Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reactor type”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Assembly of MiniFuel Targets for Irradiation of U-Mo Fuel Specimens in the High Flux Isotope Reactor

To support the development of advanced low-enriched uranium for use in nuclear reactors, irradiation testing of U-Mo disk specimens was performed at the Oak Ridge National Laboratory (ORNL) High Flux Isotope Reactor (HFIR) to collect experimental irradiation data on this type of fuel at pressurized water reactor–relevant temperatures. U-Mo is a uranium alloy that has superior dimensional stability relative to alpha-phase uranium metal and has a substantially higher uranium density compared to UO 2 . U-Mo disks specimens were fabricated at Idaho National Laboratory and inserted into MiniFuel targets for HFIR irradiation. Three MiniFuel targets were successfully assembled, welded, tested, and delivered to HFIR, along with their quality assurance documentation. The targets were inserted into HFIR’s inner vertical experiment facility within the permanent beryllium reflector. Each target contains six disk specimens and will be irradiated in HFIR for three, four, and eight cycles, with target temperatures between 250 and 500°C. This report summarizes the experiment design, test matrix, pre-characterization of specimens, and experiment assembly.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Impact of reactor architecture and design parameters on the performance of microbial electrolysis cells revealed by the electrode potential slope analysis

Microbial electrolysis cells (MECs) are appealing for recovering the chemical energy contained in domestic and industrial liquid wastes as hydrogen gas. Despite several years of research in the field, there is still a lack of critical analysis of how the reactor architecture dictates the electrochemical performance of the cell. In this study, internal resistance and onset voltage from the electrode potential slope analysis (EPS) were used in combination with current density, hydrogen production rate, reactor packing density, electrode spacing, membrane type and composition from 23 different studies to identify the reactor design parameters that primarily govern electrochemical performance of MECs. Using anion exchange membranes resulted in smaller internal resistances (AEM R int = 41± 40 mΩ m 2 ) and larger current density (18 ± 14 A m −2 ) compared to single chamber reactors (SC R int = 68 ± 58 mΩ m 2 ; 22 ± 16 A m −2 ) or MECs with cation exchange membranes (CEM R int = 376 ± 280 mΩ m 2 ; 3.0 ± 2.1 A m −2 ). Higher electrochemical performance for AEM- and SC-MECs translated in larger hydrogen gas production rates (0.122 mL H 2 C −1 for AEM vs 0.117 mL H 2 C −1 for SC), but only when inhibitors against hydrogen scavengers were added in single chamber systems (0.080 mL H 2 C −1 for SC without inhibitors). Following membrane type and composition, maintaining a small electrode spacing was the most critical parameter to improve MEC performance, indicating that the low conductivity of the media primarily limit performance by increasing ohmic resistance. Here, reactor volume and electrode surface area negatively correlated with internal resistance and current density, indicating that better performance of scaled-up reactors can likely be obtained by stacking multiple smaller units rather than just increasing reactor size. Although challenges remain in the implementation of MECs for hydrogen production from liquid wastes, advances in electrochemical engineering of the reactors can facilitate scale up and performance prediction at scale.

Electrochemistry↗
DOE OSTI2024

Degradation and Failure Phenomena of Advanced Reactor Fuel Concepts: Sodium-Cooled Fast Reactor Metallic Fuel

The U.S. Nuclear Regulatory Commission (NRC) is anticipating licensing applications and commercial use of new fuel types in advanced nuclear power reactors that would be designed and built in the United States. Pacific Northwest National Laboratory (PNNL) is providing technical assistance to the NRC related to the newly proposed nuclear fuel and cladding designs that would be deployed in these reactors. This report focuses specifically on the metallic fuel that is being considered for sodium-cooled fast reactors and specifically on mechanisms that would cause damage or failure to the fuel under reactor operating conditions and design basis accident conditions. There is historic experience with both metallic and oxide fuels in experimental sodium-cooled fast reactors, but this report will focus solely on metallic fuel. Currently two U.S.-based reactor designers are engaged with the NRC in the application or pre-application review and considering a sodium-cooled fast reactor. TerraPower is engaged with NRC in pre-application review of its Natrium reactor. The current design for this fuel uses a sodium-bonded uranium-10wt% zirconium (U10Zr) fuel clad in HT9 stainless steel. ARC Clean Technology is engaged with NRC in pre-application review of its ARC-100 reactor. The current design for this fuel uses a sodium-bonded uranium-10wt% zirconium (U10Zr) fuel with steel cladding. This report will focus on this fuel system specifically, with broader information given regarding other metallic fuel systems with other stainless steel alloy claddings. To support the NRC’s readiness efforts, this report will identify and discuss degradation and failure modes of metallic fuel concepts for sodium-cooled fast reactors, including fuel performance characteristics that may not be addressed within existing regulatory documents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Assessment of Cladding-Cladding Delamination Failures in U-Mo Fuel Plates

Monolithic fuel is a candidate fuel form for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo alloy-based fuel in a monolithic form that is sandwiched between zirconium diffusion barriers and encapsulated in an aluminum cladding. To qualify this fuel system, the program must demonstrate that the fuel meets the safety standards, has a predictable behavior, and performs well in a reactor. Although many plates have shown satisfactory thermo-mechanical performance in reactor, a small number of experimental plates exhibited failures, rendering performance of these plates unacceptable. Post-irradiation examinations of failed plates have revealed that various failures modes are present, including pillowing, blistering, buckling, warping, delamination, fracture, rupture, oxide spallation, etc. Previous studies have implied that such various operational and loading conditions could generate a complex stress-strain state, facilitating distinct failure modes that could impact the structural integrity. To understand such various failure modes, a comprehensive set of studies focusing on failure modes is being performed. As a part of these studies, this work studies the cladding-cladding separation failures that were observed in some of previous irradiation tests. To understand the root cause of cladding separation failures, selected plates from previous irradiation experiments were simulated under comparable operational conditions. Stress-strain state of the plates at the interface were examined. The results were comparatively evaluated to understand possible effects of stress state of the bond-line on delamination failures. This paper presents these findings, discusses such failure modes, and examines the influence of various factors on previously observed cladding delamination failures.

42 ENGINEERING↗
DOE OSTI2021

Modeling Summary of ASNF in DOE Sealed Standard Canisters

A pathway for road-ready and final disposition packaging configurations for the aluminum-clad spent nuclear fuel (ANSF) fuel dictates storage within helium backfilled sealed DOE standard canisters. The typical packaging configuration for the 15-foot DOE canisters places 10 advance test reactor (ATR) elements within a Type 1a basket, and three baskets are loaded within each DOE canister. During in-reactor operations and cooling pond storage conditions, oxyhydroxide layers form on the surface of the aluminum clad fuel. These layers produce hydrogen gas over time due to the fuel’s radiation field. As part of the packing procedure, the ATR fuel should be dried to remove any residual physio-/chemi- sorbed water bound to the surface. The results of this modeling will include results at fully saturated and fully dried conditions. In addition, fuels that are currently stored at the Savannah River Site were also studied for their potential for hydrogen and pressure build up. These two additional fuels modeled were the Missouri University Research Reactor (MURR) fuel, which is packaged in the same configuration as the ATR, but with a 10-foot-tall DOE standard canister. This was selected due to its relatively high decay heat compared to other DOE-managed ASNF. The second additional fuel studied with the modeling effort was the High Flux Isotope Reactor (HFIR) fuel. This fuel is modeled as two separate DOE canisters with the inner and outer annulus split for storage. The HFIR was selected for study due to its high aluminum cladding surface area. In the associated experimental work, Task 2 - Oxyhydroxide Layer Radiolytic Gas Generation Resolution, additional tests were completed in a helium environment, and updated G-values for the radiolytic production of hydrogen from the oxyhydroxide layers were provided. These values were 2.92 ×10 -4 µmol/J at 50% relative humidity and 4.12 ×10 -4 µmol/J at 100% relative humidity. These values are lower than the value for Argon that was used in prior modeling results. In addition, prior modeling results have been completed with the G-value applied to just the mass of the corrosion layer, and this has been updated to apply the G-value for hydrogen generation to the full mass of the fuel. These two effects combine to show much smaller pressure and hydrogen build up for the sealed canister model. For a nominal scenario of stored ATR fuel, after 50 years the model results give a 1.36 atm total pressure, 7% mole percent hydrogen, for the upper decay heat, 1.51 atm total pressure, 16% mole percent hydrogen, and for upper decay heat with undried fuel 2.6 atm total pressure, 15% mole percent hydrogen. For the MURR nominal case, the model results give 1.34 atm and 6% hydrogen, for upper decay heat this gives 1.41 atm total pressure with 10.8 % hydrogen, and for upper decay heat with undried fuel, this gives 2.38 atm total pressure with 9.9% hydrogen. The nominal scenario for HFIR fuel gives 1.39 atm total pressure with 9.9% hydrogen, the upper decay heat case gives 1.43 atm with 12.1% hydrogen, and the upper decay heat with undried fuel gives 2.17 atm total pressure with 11.9% hydrogen. These results confirm the ATR scenario bounds the other intact ASNF modeled here. No case modeled yields significant oxygen, and the lower decay heat cases for all fuels modeled have hydrogen concentrations that are under the 4% flammability limit after 50 years of storage. In addition, the modeled pressures for all cases are all significantly below the 500-psi limit for the DOE standard sealed canister.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Approach to nuclear criticality in IAN-R1 research reactor

The Republic of Colombia is operating a small 100 kW(t) research reactor. The reactor was provided to Colombia under the U.S. Atoms for Peace Program, and which was fueled with MTR HEU fuel enriched nominally to 93% U{sup 235}. With the cooperation of the International Atomic Energy Agency IAEA, it was prepared a new safety analysis report for performing an HEU to LEU conversion of the IAN-R1 reactor and manufacture TRIGA type LEU (19.7%, enriched) fuel to replace the original MTR-HEU fuel plate assemblies. This paper describes the activities which were achieved during the approach to nuclear criticality. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2021

Thermo-physical Properties of U-10Mo Monolithic Fuel

Monolithic fuel is a candidate fuel form that is being considered for the conversion of high-performance research reactors. This plate-type fuel consists of a high-density, U-Mo fuel in a monolithic form that is sandwiched between zirconium diffusion barriers and encapsulated in an aluminum cladding. To date, many plates were irradiated with a satisfactory irradiation performance, demonstrating that the conceptual design works. The program is now moving to the qualification phase, a predecessor to the timely conversion of the target reactors. To qualify this fuel system, the program must show that the fuel plates have predictable behavior, meet the safety standards, and perform well in reactors. The requirement of a satisfactory irradiation performance under normal operating conditions is primarily demonstrated by a successful testing. To demonstrate that the fuel system has a predictable behavior, the several key material properties should be quantified accurately since these properties are needed to estimate the thermal and mechanical behavior of the fuel system. Although, there is a large set of thermophysical property data available for unirradiated material, the property data for irradiated fuel is scarce. Since irradiation causes drastic effects in material, a significant change in material properties occurs. Consequently, using representative degradation models becomes essential for accurate performance assessments. This work examines thermal conductivity of U-10Mo, by evaluating recent experimental data from the literature and available theoretical models. The study has discovered inconsistencies in the literature data, revealing that previously developed theoretical models fail to predict the thermal conductivity of irradiated fuel.

42 ENGINEERING↗
DOE OSTI2021

Development of Enabling Technologies for Chemical Looping Combustion and Chemical Looping with Oxygen Uncoupling (Final Report)

This report summarizes results from the project, “Development of Enabling Technologies for Chemical Looping Combustion and Chemical Looping with Oxygen Uncoupling,” which evaluated several aspects of dual fluidized bed chemical looping combustion and chemical looping with oxygen uncoupling (CLOU). The objective was to provide tools and enabling technologies to help advance fluidized bed chemical looping technology to pilot, demonstration and commercial scale. One focus area is oxygen carriers, which are key to chemical looping combustion. The copper oxygen carrier-coal ash system was systematically evaluated through a combination of thermodynamic modeling and lab-scale experiments, taking into consideration different oxygen carrier support materials and coal types. A method of mapping “safe” and “risk” zones for different combinations was established, and recommendations for target conditions are provided. In addition, a simple solution for limiting negative influence of some coal ashes, namely adding small amounts of calcium to the system, is proposed. In addition, a novel process for recovering and recycling copper from spent oxygen carriers is proposed. A new approach for design and operation of loop seals in a CLOU system was developed, and involves distinct gas injection points and a short horizontal section to help control the fate of the fluidizing gases. For the air-to-fuel reactor loop seal, the upstream side is fluidized with air, ideally input into the side rather than into the bottom, which prevents uncoupling (reduction) of the oxygen carrier before entering the fuel reactor. Also, alternative for separating oxygen carrier particles and gas in circulating fluidized bed-based chemical looping system is proposed. A new reduced reaction scheme for conversion of coal in copper-based CLOU was developed and implemented into CPFD Software’s Barracuda VR package. The resulting model provides higher fidelity than the baseline, especially when it comes to minor reactions that are part of the overall combustion environment. For in-reactor heat extraction, it was determined in this project that the best way to do that in a dual circulating fluidized-bed system is through heat exchange low in the air reactor. The air reactor is the hotter of the two and for a fast-fluidized circulating bed, the lower, more dense section has a higher heat transfer coefficient and offers more consistent particle-wall contact since it doesn’t have the splashing behavior the top of the bed does. It was determined that just the wall surface area in the lower quarter to third of the air reactor is sufficient to control temperatures in both reactors. Finally, consideration was given to a new concept for CLC, which involves a staged fuel reactor with a different type of oxygen carrier in each stage.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2021

Fate and transport of unruptured tri-structural isotropic (TRISO) fuel particles in the event of environmental release for advanced and micro reactor applications

Advanced nuclear reactor designs and advanced fuel types offer safety features that may reduce environmental consequences in an accident scenario when compared to conventional reactors and fuels. One advanced reactor fuel is tri-structural isotropic (TRISO) fuel particles which are approximately 0.9 mm in diameter. TRISO particle mobility, assuming the particle is unruptured and the encapsulated radionuclides are contained, was explored through a theoretical examination of mobility through atmospheric, soil and groundwater, surface water, and non-human biota transport pathways. TRISO particles are too large and dense to travel in the atmosphere except under extreme conditions. TRISO particles are too large to penetrate most soil profiles and so cannot be transported with groundwater. TRISO particles will settle out of the water column in surface waters but the transport will depend on the energy of the body of water and likelihood of extreme dispersion events. TRISO particles could be transported by non-human biota. The size of TRISO particles could allow them to be intentionally moved by non-human biota if they are ingested as a gastrolith or if they are mistaken for something in the organism’s diet. Generally, TRISO particles will have reduced environmental mobility compared to releases of radionuclides in the event of an accident in a conventional nuclear reactor. The extent of transport has implications in emergency planning zone designations and other considerations for licensing and deploying TRISO-fueled reactors. Finally, further research and experimental work exploring TRISO particle mobility is required to understand the full environmental mobility of TRISO particles.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2026

Microwave-Assisted Plastic Upcycling: Dynamic Data Reconciliation, Parameter Estimation, and Kinetic Modeling

Microwave (MW)-assisted catalytic pyrolysis offers a promising pathway for efficient plastic upcycling. This work develops an integrated modeling framework combining dynamic data reconciliation, a temperature-dependent rate model, and a yield model to represent the time-varying production rate of components in MW-assisted LDPE pyrolysis conducted in a batch reactor. An Arrhenius-type rate model with a temperature-dependent reaction order is developed. A biexponential correlation is proposed for the yield of gaseous products that enables to capture the evolving product formation behavior during conversion. In the yield correlation, one term is used to represent the initial increase in yield, reflecting the rapid formation of intermediate or primary products at the early stages of the reaction when a larger fraction of the reactant remains available. As conversion progresses, the influence of this term gradually diminishes. The other term accounts for the subsequent decrease in the predicted yield, representing secondary reactions such as further cracking or coke formation that reduce the concentration of certain products at higher conversion. The model is found to accurately represent reconciled experimental flow rate profiles from an in-house MW-assisted catalytic batch reactor for major products, including ethylene, ethane, 1-butene, and benzene, across 250−350 °C. Ethylene remains the dominant product but decreases from about 41.95% at 250 °C to 30.14% at 350 °C, while heavier products increase significantly, with 1-butene rising to nearly 8.37% and benzene reaching 2.17% at intermediate temperatures. The model shows that the ethylene production rate can be maximized at around 270 °C. The models developed in this work can be utilized for process optimization, reactor design and scale-up of microwave-assisted plastic conversion technologies, and economic analysis.

Damahe, Harish [West Virginia Univ., Morgantown, W↗
DOE OSTI2026

Coupled CVD and Float Zone Reactor for Lower Cost, Higher Efficiency Si Boules (Final Technical Report)

This project modeled a new type of photovoltaic (PV) Si production reactor with the promise to reduce the cost, increase the efficiency, and reduce the energy required to manufacture Si wafers. The production of photovoltaic (PV) grade Si is well established, based on the pulling of single crystalline Si boules from polycrystalline Si created from trichlorosilane using the Siemens process. However, these processes are very energy intensive, and manufacturing of PV Si occurs almost entirely in China. To disrupt this paradigm and on-shore production of this critical material and provide benefits to the public, a substantial technological leap is required to move past incumbent technology. This study evaluated a new float zone chemical vapor deposition (Fz-CVD) concept in which trichlorosilane (TCS), the feedstock for polysilicon in the Siemens process, is injected directly into a float zone crystallizer to continuously deposit the feed rod for the boule pulling process through a combination of multiphysics modeling and technoeconomic analysis.

14 SOLAR ENERGY↗
DOE OSTI2020

Preliminary Study on TRISO Fuel Cross Section Generation

Cross section self-shielding methodologies for TRISO fuel were assessed to provide accurate multigroup cross sections for a high-fidelity reactor physics code so that the code is able to accurately model and simulate advanced reactors with TRISO fuel. Initially, the two existing methodologies (the SCALE method and the Sanchez-Pomraning method) were studied and implemented to MC2-3 for detailed performance tests. Additionally, a new spatial self-shielding method, named the iterative local spatial self-shielding (ILSS) method, for particulate fuels was developed based on the disadvantage factor and implemented to MC2-3 as well. The new method approximately accounts for the effect of randomly distributed particles on the particle shadowing effect using a homogenized compact region surrounding a particle of interest at the center. The self-shielded cross sections of the particle at the center are determined iteratively since the cross sections of the homogenized compact region are calculated using them. For the energy range above 100 keV where the fuel-to-moderator ratio is more important than the random distribution of particles, a single particle unit-cell model is used by preserving the average amount of moderator per fuel particle in the system. The three self-shielding methods implemented in MC2-3 were tested using numerical benchmark problems made based on fuel compact problems of a prismatic-type very high temperature reactor. Test results indicated that the ILSS method produced slightly better results than the SCALE and Sanchez-Pomraning methods, compared to the Serpent-2 Monte Carlo results obtained with 25 independent random particle configurations. The SCALE and Sanchez-Pomraning methods tend to underestimate the heterogeneity effect by 150 and 100 pcm, respectively, while the new ILSS method overestimates the heterogeneity effect by 70 pcm. In future, the new self-shielding method will be extended to perform pebble calculations and compare results with those from the SCALE and Sanchez-Pomraning methods. Furthermore, the new method will be optimized for practical applications to on-the-fly resonance treatment for lattice or whole-core calculations for advanced reactors.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Report on Initial Sodium Testing on the Thermal Hydraulic Experimental Test Article (THETA) (Fiscal Year 2024 Final Report)

The Thermal Hydraulic Experimental Test Article (THETA) is a facility that is used to develop sodium components and instrumentation as well as to acquire experimental data for validation of reactor thermal hydraulic and safety analysis codes. The facility simulates nominal thermal hydraulic conditions as well as protected/unprotected loss of flow accidents in a sodium-cooled fast reactor (SFR). High fidelity distributed temperature profiles of the developed flow field may be acquired with Rayleigh backscatter based optical fiber temperature sensors. The facility was designed in partnership with systems code experts to tailor the experiment to ensure the most relevant and highest quality data for code validation. THETA is comprised of a traditional primary coolant and secondary coolant system. The primary system is submerged in the pool of sodium and consists of a pump, electrically heated core, intermediate heat exchanger, and connected piping and thermal barriers (redan). The secondary system, located outside of the sodium pool, consists of a pump, sodium to air heat exchanger, and connected piping and valves. In fiscal year 2023, thermal stratification tests were completed with the primary system online, while the secondary system was being constructed [1]. These tests had shown that the core barrel and intermediate heat exchanger (IHX) outlet required increased thermal insulation. The THETA primary system was removed from METL, cleaned, thermal insulators installed, and then inserted into METL Test Vessel 4. At the time of this writing the THETA primary and secondary system are operational. During this fiscal year 100+ hours of testing was completed to characterize thermal hydraulic phenomena associated with steady state and transient conditions in a pool type liquid metal cooled reactor. A majority of the testing campaign was completed to satisfy the experimental data acquisition requirements for the GAIN Voucher with Oklo, CRADA 2021-21121. THETA is still operational at the time of this publication and future testing is planned for fiscal year 2025. Work is underway to publish existing and future data to an online database to facilitate collaboration with SFR engineers looking to validate their systems code or computational fluid dynamics models.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Avoidance of disruptions on KSTAR due to vertical displacement events via novel real-time stability assessment

Disruption avoidance via the DECAF approach has been achieved on KSTAR using a novel real-time vertical stability assessment and a multiactuator feedback control strategy. The development of disruption avoidance strategies with reactor-relevant reliability is an urgent activity, enabling future fusion power plants. The stability metric employed is based on a new formulation of a vertical force gradient balance metric evaluated across the poloidal cross section of the plasma, with parameters tuned using historical data. Evaluation of this metric on a validation set of 400 recent KSTAR shots indicates >82% of Vertical displacement events can be avoided via feedback control. Essential to its calculation is the two-dimensional toroidal current density distribution in the plasma. Measurement of this profile faster than fully-converged equilibrium reconstructions can deliver is found to improve forecaster performance and is achieved with a surrogate model that takes as input magnetic diagnostic measurements and outputs the current profile on a basis comprising the top principal components of historical current profiles (from past equilibrium reconstructions). This method solves the non-uniqueness problem typically faced when reconstructing current profiles directly from diagnostics, while improving computational time and accuracy. On average, profiles produced by this model reach coefficients of determination of >0.99 with respect to those from equilibrium reconstructions. The avoidance actuators employed include poloidal field coils and an electron cyclotron current drive system. The multiactuator approach, as shown in this first demonstration, allows disruption avoidance while minimizing impact to operational performance. This ability, along with its flexibility and speed, makes this new approach an attractive option for avoiding these types of disruptions in reactors.

Tobin, Matthew [Columbia Univ., New York, NY (Unit↗
DOE OSTI2020

Noncontact Flow Rate Using Laser Ultrasonics

Several types of advanced nuclear reactors are cooled with high-temperature liquid metal or molten salt flows. There is a critical need to measure flow velocity in flow channels for test purposes, and eventually in operational reactors. In conventional ultrasonic flow sensors, ultrasonic waves traveling in both the upstream and downstream directions are generated and detected by transducers that must contact the flow channels. A shift in the frequency or transit time between the two ultrasonic waves is measured to determine flow velocity. We describe here an initial effort to apply that sensing concept when the contact transducers are replaced by laser-based generation and detection instrumentation. This noncontact sensing avoids many practical problems associated with contact transducers when implemented on flow channels at high temperature. Laser-based flow monitoring can also be applied to hot-process piping in the geothermal energy, chemical-processing and petroleum-refining industries. Our effort has included theoretical simulation of noncontact laser-based flow monitoring, indicating capability of measuring flow velocities relevant to reactor cooling. It also included a room-temperature experimental demonstration using water as the flow liquid, and indicating capability of measuring flow velocity at a responsivity roughly consistent with simulation predictions. Plans were made for an experimental demonstration at Oregon State University using liquid metal at 110 degrees C.

02 PETROLEUM↗
DOE OSTI2021

Nuclear Fuels and Reprocessing Technologies: A U.S. Perspective

Reprocessing and/or waste management issues are of concern to the “back end” of the nuclear fuel cycle. Of course, there are a great many “nuclear fuel cycle” scenarios to consider; if not in practice, then at least in theory. The simplest conceptually is the “once through” fuel cycle in which the spent fuel is discarded. The more complex fuel cycle scenarios involve reprocessing spent nuclear fuels and a family of nuclear reactor technologies to accommodate burning and breeding for various military and commercial needs. Therefore, the selection of a specific “fuel cycle” is what ultimately imposes the engineering requirements of the reprocessing and waste management technologies. No one part is independent of the other parts in a fuel cycle flowsheet; all parts are fully integrated. This paper presents a summary of radiochemical processes, nuclear reactor technologies, nuclear fuel types, and the reprocessing technologies that serve the different nuclear fuel types. Comprehending how this series of topics are related to each other is a prerequisite to understanding the requirements of any reprocessing strategy. The summary materials presented here are selective, as opposed to comprehensive. More detailed information on any one subject can be found in the reference materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Multiphysics Analysis of Load Following and Safety Transients for MicroReactors

The tools developed within the U.S. Department of Energy (DOE) Office of Nuclear Energy’s Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aim at providing high fidelity multiphysics modeling capabilities to support design and licensing of various types of advanced nuclear reactors, including the technologies being developed by U.S. microreactor vendors relying on heat pipe and gas-cooled technologies. In FY-2022, the NEAMS Multiphysics Applications team made significant progress both in demonstrating capabilities applied to microreactor problems, and in supporting NEAMS developers.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗