Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “power density”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Development of High Bs Fe-Ni Based Metal Amorphous Nanocomposite by Optimization of Glass Forming Ability

A growing interest in electric vehicles challenges soft magnetic materials to improve efficiency and power density. Metal amorphous nanocomposites (MANCs) have lower coercivities and eddy current losses, allowing for greater efficiency and higher switching frequency. The later allows for high motor speeds and improved power density. However, commercially available and laboratory demonstrated MANCs have shortcomings. Fe-based MANCs, such as FINEMET have excellent magnetic properties, but mechanical properties limit their application in high speed electric motors (HSMs). Fe-Co based MANCs, such as HITPERM, have high saturation inductions and good mechanical properties, but elevated magnetostrictive losses. Co-based MANCs and more recent Fe-Ni based MANCs have low losses and good mechanical properties, but lower saturation inductions (1-1.2 T), that limit power density in HSMs. Recently, much work has explored improving saturation induction in MANCs by increasing the content of magnetic elements, which comes at the cost of glass-forming ability (GFA). These efforts where generally limited to trial and error testing. Additionally, all work to date has focused on Fe-based alloys. In this work, a method of using Thermocalc simulation to locate near-eutectic compositions has been applied to Fe-Ni based alloys. Minima in liquidus temperature and solidification range were found for a ternary composition range and used to identify compositions that retain good GFA as the percentage of magnetic elements is increased. The (Fe 70 Ni 30 ) x (B-Si-Nb) 100-x alloy system for x=82% and x=85% was explored by Thermocalc simulations. This is an increase in magnetic element content compared to previously developed x=80% alloys. 3 compositions in the x=82% system, and 1 alloy in the x=85% system where identified and successfully cast as amorphous ribbon. The amorphous nature of the ribbon was confirmed by a bend test and XRD. Magnetic testing was performed by PPMS to measure saturation induction and Curie temperature of the amorphous material. The Curie temperatures increased to 407-438 °C for the x=82% alloys, and 462 °C for the x=85% alloy. Saturation induction increased to 1.28-1.36 T for the x=82% alloy and 1.48 T for the x=85% alloy, which is a significant improvement over the ~370 °C Curie temperature and 1.2 T saturation of previous Fe-Ni alloy. Crystallization behavior was studied by XRD for the x=85% alloy, showing that crystallization process follows a 2-step process of Amorphous → BCC+FCC+Amorphous → BCC+FCC+Fe 3 B+Fe 23 B 6 . Post annealing magnetic properties were studied by strip testing, and saturation induction as high as 1.48 T was seen after optimal annealing. TEM was used to study structure of as cast and annealed material. 2 alloys with x=82% compositions were identified with an optimal crystalline size of 10-20 nm, while the x=85% alloy had this structure in the as cast state. This opens the possibility of using the alloy in the as cast state, without requiring annealing. In conclusion, alloys with good GFA and improved magnetic properties were identified by Thermocalc simulation.

Krimer, Yuval↗
NASA NTRS1983

The development of a power spectral density processor for C and L band airborne radar scatterometer sensor systems

A real-time signal processor was developed for the NASA/JSC L-and C-band airborne radar scatterometer sensor systems. The purpose of the effort was to reduce ground data processing costs. Conversion of two quadrature channels of data (like and cross polarized) was made to obtain Power Spectral Density (PSD) values. A chirp-z transform (CZT) approach was used to filter the Doppler return signal and improved high frequency and angular resolution was realized. The processors have been tested with record signals and excellent results were obtained. CZT filtering can be readily applied to scatterometers operating at other wavelengths by altering the sample frequency. The design of the hardware and software and the results of the performance tests are described in detail.

Harrison, D. A., III↗
DOE OSTI2021

Seismically Detecting Nuclear Reactor Operations Using a Power Spectral Density (PSD) Misfit Detector

To explore the ability to indirectly detect and attribute various operations conducted at a nuclear reactor using waveform data, we investigated the seismic signals recorded near the High Flux Isotope Reactor (HFIR) located at Oak Ridge National Laboratory in Oak Ridge, Tennessee. Specifically, we processed seismic data collected from a single seismoacoustic station, WACO, near the HFIR facility, and employed a power spectral density misfit detector to identify signals of interest and associate the detections with operational events. Initial results suggest that this method provides a promising means of regularly detecting at least 19 unique operations. Furthermore, with additional station deployment and more comprehensive data logs, we anticipate that future analysis will offer an additional means to seismically monitor nuclear reactors (such as HFIR) health and performance more accurately.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
NASA NTRS1999

Hard X-Ray Variability of the Black Hole Candidate GRO J0422+32 During its 1992 Outburst

We have studied the hard X-ray variability of the soft X-ray transient GRO J0422+32 with BATSE (Burst and Transient Source Experiment) in the 20-100 keV energy band. Our analysis covers 180 days following the first X-ray detection of the source on August 5, 1992, fully covering its primary and secondary X-ray outbursts. We compute power density spectra (PDSs) in the 20-50, 50-100, and 20-100 keV energy bands, in the frequency interval 0.002-0.488 Hz. The PDSs of GRO J0422+32 are approximately flat up to a break frequency, and decay as a power law above it, with index approximately 1. During the first 70 days of the X-ray outburst, the PDSs of GRO J0422+32 show a significant quasi-periodic oscillation (QPO) peak near approximately 0.2 Hz, superposed on the power-law tail. The break frequency of the PDSs obtained during the primary X-ray outburst of GRO J0422+32 occurs at 0.041 +/- 0.006 Hz; during the secondary outburst, the break is at 0.081 +/- 0.015 Hz. The power density at the break ranged between 44% and 89% / square root of Hz (20-100 keV). The canonical anticorrelation between the break frequency and the power density at the break, observed in Cyg X-1 and other BHCs in the low state, is not observed in the PDSs of GRO J0422+32. We compare our results with those of similar variability studies of Cyg X-1. The relation between the spectral slope and the amplitude of the X-ray variations of GRO J0422+32 is similar to that of Cyg X-1; however, the relation between the hard X-ray flux and the amplitude of its variation is opposite to what has been found in Cyg X-1. Phase lags between the X-ray flux variations of GRO J0422+32 at high and low photon energies could only be derived during the first 30 days of its outburst. During this period, the variations in the 50-100 keV band lag those in the 20-50 keV energy band by an approximately constant phase difference of 0.039(3) rad in the frequency interval 0.02-0.20 Hz. The time lags of GRO J0422+32 during the first 30 days of the outburst decrease with frequency as a power law with index 0.9 for v > 0.01 Hz.

vanderHooft, F.↗
NASA NTRS1998

Hard X-Ray Variability of the Black Hole Candidate GRO J0422+32 During its 1992 Outburst

We have studied the hard X-ray variability of the soft X-ray transient GRO J0422+32 with the Burst and Transient Source Experiment (BATSE) in the 20-100 keV energy band. Our analysis covers 180 days following the first X-ray detection of the source on 1992 August 3, fully covering its primary and secondary X-ray outburst. We computed power density spectra (PDSS) in the 20-50, 50-100, and 20-100 keV energy bands., in the frequency interval 0.002-0.488 Hz. The PDSs of GRO J0422+32 are approximately flat up to a break frequency and decay as a power law above, with index about 1. During the first 70 days of the X-ray outburst, the PDSs of GRO J0422+32 show a significant QPO Peak near about 0.2 Hz, superposed on the power-law tail. The break frequency of the PDSs obtained during the primary X-ray outburst of GRO J0422+32 occurs at 0.041+/-0.006 Hz; during the secondary outburst the break is at 0.081q0.01.5 Hz. The power density at the break ranged between 44 and 89% Hz(exp -1/2) 20-100 keV). The canonical anticorrelation between the break frequency and the power density at the break, observed in Cyg X-1 and other BHCs in the low state, is not observed in the PDSs of GRO J0422+32. We compare our results with those of similar variability studies of Cyg X-1. The relation between the spectral slope and the amplitude of the X-ray variations of GRO J0422+32 is similar to that of Cyg X-1.

VanderHooft, F.↗
DOE OSTI2021

The Silencing of U.S. Campuses Following the COVID-19 Response: Evaluating Root Mean Square Seismic Amplitudes Using Power Spectral Density Data

In response to the COVID-19 global pandemic, many populated and active regions have become deserted and show significant reductions in their background seismicity, especially campuses across the United States (U.S.). Seismic sensors located in the vicinity of or within U.S. campuses show that anthropogenic seismic noise remains elevated during the ordinary, nonpandemic, academic year, only subduing during periods of recess (e.g., winter break). Here, we use power spectral density (PSD) data computed by the Incorporated Research Institutions for Seismology Data Management Center for quality assessment to calculate root mean square (rms) amplitude and analyze the effects of the COVID-19 school closures. We processed and analyzed PSD data for 46 seismic stations located within 50 m of a U.S. university or college. Results show that 42 campus stations show an overall rms drop following a statewide school closure.

58 GEOSCIENCES↗
NASA NTRS2017

Results of All Polyimide, Etched Foil Heater Qualification and Failure Limit Testing

Standard FEP (Fluorinated Ethylene Propylene resin) polyimide (SFP) or Kapton film heaters—which have a long history of space flight—are output-power limited by the melting point of Teflon which is used as an adhesive and insulator between the encasing layers of Kapton. The limit is expressed as a power density or through maximum operating temperature limits. All-polyimide (AP) heaters (also known as adhesive-less heaters) do not contain FEP Teflon between the layers of Kapton so the heaters are unconstrained by the melting point of Teflon. Thus, AP heaters have a higher maximum power density and operating temperature. AP heaters have not been qualified or flown on JPL missions but could be useful in applications that require a higher power density (Watt density) than the SFP heaters can support. The purpose of this paper is to document the qualification and property testing of the AP heaters for flight purposes. JPL (Jet Propulsion Lab.) tested several varieties of all-polyimide heaters to determine their functional equivalence to the standard heater which has substantial flight heritage and to determine their maximum limits. Tests included standard in-air burn-in tests, maximum power testing, lead pull strength, process qualification verification (PQV), long duration thermal cycling, and electro-magnetic compatibility shielding properties for copper-cladded shielded heaters. The results show that the all-polyimide heater appears to be functionally equivalent to the standard heater and has a higher Watt density and maximum operating temperature limit. The tests, test articles, failure analysis of the test articles, and results are described herein. These test results indicate that the all-polyimide heater is ready for flight applications.

Cucullu, Gordon C., III↗
DOE OSTI2025

Overcoming the Conductance versus Crossover Trade-off in State-of-the-Art Proton Exchange Fuel-Cell Membranes by Incorporating Atomically Thin Chemical Vapor Deposition Graphene

Permeance–selectivity trade-offs are inherent to polymeric membranes. In fuel cells, thinner proton exchange membranes (PEMs) could enable higher proton conductance and increased power density with lower area-specific resistance (ASR), smaller ohmic losses, and lower ionomer cost. However, reducing thickness is accompanied by an increase in undesired species crossover harming performance and long-term efficiency. Here, we show that incorporating atomically thin monolayer graphene synthesized via scalable chemical vapor deposition (CVD) and tunable defect density into PEMs (Nafion, ~5–25 μm thick) can allow for reduced H 2 crossover (~34–78% of Nafion of a similar thickness) while maintaining adequate areal proton conductance for applications (>4 S cm –2 ). In contrast to most prior work using >50 μm symmetric Nafion sandwich structures, we elucidate the interplay of graphene defect density and Nafion proton transport resistance on the performance of Nafion|graphene composite membranes and find high-quality low-defect density CVD graphene (G) supported on Nafion 211 (~25 μm); i.e., N211|G has a high areal proton conductance (~6.1 S cm –2 ) and the lowest H 2 crossover (~0.7 mA cm –2 ). Fully functional centimeter-scale N211|G fuel-cell membranes demonstrate performance comparable to that of state-of-the-art Nafion N211 at room temperature as well as standard operating conditions (~80 °C, ~150–250 kPa-abs) with H 2 /air (power density ~0.57–0.63 W cm –2 ) and H 2 /O 2 feed (power density ~1.4–1.62 W cm –2 ) and markedly reduced H 2 crossover (~53–57%).

25 ENERGY STORAGE↗
DOE OSTI2023

Cracked Film Lithography with CuGaO x Buffers for Bifacial CdTe Photovoltaics

Abstract Bifacial CdTe solar cells with greater power density than the monofacial baselines are demonstrated by using a CuGaO x rear interface buffer that passivates while reducing sheet resistance and contact resistance. Inserting CuGaO x between the CdTe and Au increases mean power density from 18.0 ± 0.5 to 19.8 ± 0.4 mW cm −2 for one sun front illumination. However, coupling CuGaO x with a transparent conductive oxide leads to an electrical barrier. Instead, CuGaO x is integrated with cracked film lithography (CFL)‐patterned metal grids. CFL grid wires are spaced narrowly enough (≈10 µm) to alleviate semiconductor resistance while retaining enough passivation and transmittance for a bifacial power gain: bifacial CuGaO x /CFL grids generate 19.1 ± 0.6 mW cm −2 for 1 sun front + 0.08 sun rear illumination and 20.0 ± 0.6 mW cm −2 at 1 sun front + 0.52 sun rear—the highest reported power density at field albedo conditions for a scaled polycrystalline absorber.

14 SOLAR ENERGY↗
NASA NTRS2004

InGaAs/InP Monolithic Interconnected Modules (MIM) for Thermophotovoltaic Applications

There has been a traditional trade-off in thermophotovoltaic (TPV) energy conversion development between systems efficiency and power density. This trade-off originates from the use of front surface spectral controls such as selective emitters and various types of filters. A monolithic interconnected module (MIM) structure has been developed which allows for both high power densities and high system efficiencies. The MIM device consists of many individual indium gallium arsenide (InGaAs) devices series -connected on a single semi-insulating indium phosphide (InP) substrate. The MIMs are exposed to the entire emitter output, thereby maximizing output power density. An infrared (IR) reflector placed on the rear surface of the substrate returns the unused portion of the emitter output spectrum back to the emitter for recycling, thereby providing for high system efficiencies. Initial MIM development has focused on a 1 sq cm device consisting of eight series interconnected cells. MIM devices, produced from 0,74 eV InGAAs, have demonstrated V(sub infinity) = 3.23 volts, J(sub sc) = 70 mA/sq cm and a fill factor of 66% under flashlamp testing. Infrared (IR) reflectance measurement (less than 2 microns) of these devices indicate a reflectivity of less than 82%. MIM devices produced from 0.55 eV InGaAs have also been den=monstrated. In addition, conventional p/n InGaAs devices with record efficiencies (11.7% AM1) have been demonstrated.

Wilt, David M.↗
NASA NTRS1997

Electrical and Optical Performance Characteristics of 0.74-eV p/n InGaAs Monolithic Interconnected Modules

There has been a traditional trade-off in thermophotovoltaic (TPV) energy conversion development between system efficiency and power density. This trade-off originates from the use of front surface spectral controls such as selective emitters and various types of filters. A monolithic interconnected module (MIM) structure has been developed which allows for both high power densities and high system efficiencies. The MIM device consists of many individual indium gallium arsenide (InGaAs) cells series-connected on a single semi-insulating indium phosphide (InP) substrate. The MIM is exposed to the entire emitter output, thereby maximizing output power density. An infrared (IR) reflector placed on the rear surface of the substrate returns the unused portion of the emitter output spectrum back to the emitter for recycling, thereby providing for high system efficiencies. Initial MIM development has focused on a 1 sq cm device consisting of eight (8) series interconnected cells. MIM devices, produced from 0.74-eV InGaAs, have demonstrated V(sub oc) = 3.2 volts, J(sub sc) = 70 mA/sq cm, and a fill factor of 66% under flashlamp testing. Infrared (IR) reflectance measurements (greater than 2 micron) of these devices indicate a reflectivity of greater than 82%. MIM devices produced from 0.55-eV InGaAs have also been demonstrated. In addition, conventional p/n InGaAs devices with record efficiencies (11.7% AM0) have been demonstrated.

Wilt, David M.↗
NASA NTRS1997

Electrical and Optical Performance Characteristics of p/n InGaAs Monolithic Interconnected Modules

There has been a traditional trade-off in ThermoPhotoVoltaic (TPV) energy conversion development between system efficiency and power density. This trade-off originates from the use of front surface spectral controls such as selective emitters and various types of filters. A Monolithic Interconnected Module (MIM) structure has been developed which allows for both high power densities and high system efficiencies. The MIM device consists of many individual Indium Gallium Arsenide (InGaAs) devices series-connected on a single semi-insulating Indium Phosphide (InP) substrate. The MIMs are exposed to the entire emitter output, thereby maximizing output power density. An InfraRed (IR) reflector placed on the rear surface of the substrate returns the unused portion of the emitter output spectrum back to the emitter for recycling, thereby providing for high system efficiencies. Initial MIM development has focused on a 1 sq cm device consisting of eight (8) series interconnected cells. MIM devices, produced from 0.74eV InGaAs, have demonstrated V(sub infinity) = 3.2 volts, J(sub sc) = 70 mA/sq cm and a fill factor of 66% under flashlamp testing. IR reflectance measurements (greater than 2 microns) of these devices indicate a reflectivity of greater than 82%. MIM devices produced from 0.55 eV InGaAs have also been demonstrated. In addition, conventional p/n InGaAs devices with record efficiencies (11.7% AM0) have been demonstrated.

Wilt, David M.↗
DOE OSTI2021

Role of mixed conducting Pr 0.1 Gd 0.1 Ce 0.8 O 1.9-δ barrier layer on the promotion of SOFC performance

The cathode activity in a solid oxide fuel cell can be promoted by introducing various catalysts to reduce its polarization resistance towards oxygen reduction, and thus improve cell performance. Here, in this work, the La 0.6 Sr 0.4 Co 0.2 Fe 0.8 O 3 (LSCF) cathode surface is modified by the infiltration of Pr 6 O 11 and the power density at 0.8 V and 750 °C is improved by 21%. Moreover, by replacing the traditional barrier layer Gd 0.2 Ce 0.8 O 1.9 with mixed conducting Pr 0.1 Gd 0.1 Ce 0.8 O 1.9 (PGCO), the power density increases by 38%. The ohmic resistance is dramatically reduced by applying the PGCO interlayer. The distribution of relaxation time was used to analyze the mechanism for which the polarization resistance was decreased, attributing to the mixed conduction nature in PrO x . An increase of power density, ~0.358 W/cm 2 (71%) at 0.8 V, is achieved with the implementation of both surface modification and buffer layer engineering.

08 HYDROGEN↗
NASA NTRS1977

Estimates of Optimal Operating Conditions for Hydrogen-Oxygen Cesium-Seeded Magnetohydrodynamic Power Generator

The value of percent seed, oxygen to fuel ratio, combustion pressure, Mach number, and magnetic field strength which maximize either the electrical conductivity or power density at the entrance of an MHD power generator was obtained. The working fluid is the combustion product of H2 and O2 seeded with CsOH. The ideal theoretical segmented Faraday generator along with an empirical form found from correlating the data of many experimenters working with generators of different sizes, electrode configurations, and working fluids, are investigated. The conductivity and power densities optimize at a seed fraction of 3.5 mole percent and an oxygen to hydrogen weight ratio of 7.5. The optimum values of combustion pressure and Mach number depend on the operating magnetic field strength.

Smith, J. M.↗
NASA NTRS1978

A method for predicting full scale buffet response with rigid wind tunnel model fluctuating pressure data. Volume 2: Power spectral densities for method assessment

The predicted upper and lower bounds power spectra for all of the cases and response items given in Volume 1 are plotted. The flight test power spectra are shown on each prediction plot for the nominal value of angle of attack that most closely agrees with the flexible angle for the prediction. The flight test and prediction conditions are given in tabular form for all cases considered.

Cunningham, A. M., Jr.↗
NASA NTRS1987

Power spectra of quasi-periodic oscillations in luminous X-ray stars

A variety of partial random processes are considered in order to study the effects on the power-density spectrum of several physical phenomena that may occur in the beat-frequency modulated accretion (BFMA) model of QPOs. The relevant physical properties of BFMA model are summarized, and the class of random processes used to represent the X-ray intensity time series predicted by the model are introduced. The dependence of the power-density spectrum on pulse shape is discussed. Pulse-lifetime and orbital-frequency distributions are introduced, illustrating how these affect the power-density spectrum. The effect of nonuniform initial-pulse phase distributions and of nonuniform pulse-time distributions are considered. The effects of a particular type of pulse-to-pulse correlation that may be natural in the context of the BFMA model and that greatly increases the power of the oscillations relative to that in the red noise is analyzed.

Shibazaki, N.↗
DOE OSTI2023

A Hot‐Swappable, Fault‐Tolerant, Modular Power Converter System for Solar Photovoltaic Plants

The performance metrics of the state-of-the-art commercial solar inverters, such as system cost, operation and maintenance (O&M) cost, service life, reliability, maintainability, and power density are much lower than the target metrics needed to achieve SunShot’s 2030 levelized cost of energy (LCOE) goals. To overcome the shortcomings of the existing solar inverters, this project proposed a novel Hot-Swappable, Fault-Tolerant, Modular Power Converter (HSFT-MPC) concept for solar photovoltaic (PV) plants and proved the concept through the design, fabrication, and laboratory test validation of a single-phase HSFT-MPC prototype. The HSFT-MPC has the following distinct advantages over the state-of-the-art: 1) elimination of harmonic/ electromagnetic interference (EMI) filter in the inverter stage due to the novel topology, 2) lower system cost and higher power density due to the modular design, elimination of harmonic/EMI filter, and lower cooling requirement, 3) higher efficiency due to lower switching frequencies, 4) higher reliability and longer (50 years) service life due to simpler cooling and fault tolerance capability, 5) easier installation, lower O&M cost, and improved maintainability due to the modular design and hot-swappable power electronic building blocks (PEBBs), and 6) improved manufacturability due to the modular design. This project developed a single-phase HSFT-MPC prototype with 25kW nominal output power, 2.4kV, 60Hz nominal AC output, lower than 5% AC output voltage total harmonic distortion, over 5 kW/L inverter power density, and 99.4% inverter peak efficiency, being tolerant to failure of single and multiple PEBBs, and capable of hot swapping of the failed PEBB(s). The HSFT-MPC enables uninterruptable operation of the solar PV plant when failure of single or multiple PEBBs or PV modules occurs. Compared with the existing solar inverters in the market, the HSFT-MPC is expected to reduce the inverter failure-caused downtime and energy losses of solar PV plants by more than 60% and 50%, respectively. Project findings have been presented at major conferences in the field and published in peer-reviewed papers, which added new knowledge to the field of power electronics for solar PV systems. A minicourse on Solar PV Systems was developed for outreach activities. The minicourse will help attract young individuals to the renewable energy profession which has a significant talent shortage. The HSFT-MPC is expected to overcome all of the shortcomings of the state-of-the-art solar inverters in terms of cost, efficiency, service life, reliability, maintainability, and manufacturability targets needed to achieve SunShot’s 2030 LCOE goals. Therefore, the proposed HSFT-MPC concept has the great potential to disrupt the current solar inverter market. This project created a pathway towards industry adoption of the HSFT-MPC to help achieve 50-year service life solar PV systems. Since the solar PV plants using the HSFT-MPC will feature with higher reliability, longer service life, and easier maintenance, they are particularly useful for the rural areas with underserved populations that demand reliable and affordable clean electricity. The outcomes of the project have the strong potential to address national needs in the field of renewable energy to reduce CO 2 emissions from the electricity sector, reduce imports of energy from foreign sources, and improve energy security, efficiency, and sustainability. Since electricity is used in almost all of society’s sectors, the outcomes of the project will benefit various sectors of society and economy.

14 SOLAR ENERGY↗
NASA NTRS1993

Flow instability in particle-bed nuclear reactors

A three-dimensional model of the stability of the particle-bed reactor is presented, in which the fluid has mobility in three dimensions. The model accurately represents the stability at low Re numbers as well as the effects of the cold and hot frits and of the heat conduction and radiation in the particle bed. The model can be easily extended to apply to the cylindrical geometry of particle-bed reactors. Exemplary calculations are carried out, showing that a particle bed without a cold frit would be subject to instability if operated at the high-temperature ratios used for nuclear rockets and at power densities below about 4 MW/l; since the desired power density for such a reactor is about 40 MW/l, the operation at design exit temperature but at reduced power could be hazardous. Calculations show however that it might be possible to remove the instability problem by appropriate combinations of cold and hot frits.

Kerrebrock, J. L.↗