Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “nonlinear response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2007

Stability Analysis of a High-Speed Seal Test Rotor With Marginal and Extended Squeeze-Film Dampers: Theoretical and Experimental Results

A case study of a high-speed seal test rotor shows how rotor dynamic analysis can be used to diagnose the source of high vibrations and evaluate a proposed remedy. Experimental results are compared with the synchronous and non-synchronous whirl response analysis of a double overhung, high-speed seal test rotor with ball bearings supported in 5.84- and 12.7-mm-long, un-centered squeeze-film oil dampers. Test performance with the original damper of length 5.84 mm was marginal. Non-synchronous whirling occurred at the overhung seal test disk and there was a high amplitude synchronous response near the drive spline above 32,000 rpm. Nonlinear synchronous unbalance and time transient whirl studies were conducted on the seal test rotor with the original and extended damper lengths. With the original damper design, the nonlinear synchronous response showed that unbalance could cause damper lockup at 33,000 rpm. Alford cross-coupling forces were also included at the overhung seal test disk for the whirl analysis. Sub-synchronous whirling at the seal test disk was observed in the nonlinear time transient analysis. With the extended damper length of 12.7 mm, the sub-synchronous motion was eliminated and the rotor unbalance response was acceptable to 45,000 rpm with moderate rotor unbalance. Seal test rotor orbits and vibration levels with the extended squeeze film dampers showed smooth operation to 40,444 rpm.

Proctor, Margaret P.↗
NASA NTRS1973

User document for computer programs for ring-stiffened shells of revolution

A user manual and related program documentation is presented for six compatible computer programs for structural analysis of axisymmetric shell structures. The programs apply to a common structural model but analyze different modes of structural response. In particular, they are: (1) Linear static response under asymmetric loads; (2) Buckling of linear states under asymmetric loads; (3) Nonlinear static response under axisymmetric loads; (4) Buckling nonlinear states under axisymmetric (5) Imperfection sensitivity of buckling modes under axisymmetric loads; and (6) Vibrations about nonlinear states under axisymmetric loads. These programs treat branched shells of revolution with an arbitrary arrangement of a large number of open branches but with at most one closed branch.

Cohen, G. A.↗
NASA NTRS1976

Dynamic response of membranes with finite elements

A general set of finite-element equations is developed for treating the nonlinear dynamic response of membranes consisting of complex nonlinear materials. The approach proposed by Key (1974) for a most complete treatment of the finite-element method to the nonlinear dynamic analysis of solids is used in developing the nonlinear equations of motion for membranes with cubic quadrilateral finite elements. The computations are kept general with respect to material modeling by computing the deformation gradient and requiring a constitutive subroutine to supply the Cauchy stress. An example calculation of the vibration of a square membrane demonstrates the accuracy of the formulation for small deformation theory and shows the nonlinear effect of large deformations.

Benzley, S. E.↗
NASA NTRS1957

Experimental Comparison of Speed : Fuel-flow and Speed-area Controls on a Turbojet Engine for Small Step Disturbances

Optimum proportional-plus-integral control settings for speed - fuel-flow control, determined by minimization of integral criteria, correlated well with analytically predicted optimum settings. Engine response data are given for a range of control settings around the optimum. An inherent nonlinearity in the speed-area loop necessitated the use of nonlinear controls. Response data for two such nonlinear control schemes are presented.

ENGINES, CONTROL - TURBOJET↗
NASA NTRS1993

Projections on structures and material strength in the computational context

The ideas associated with the subsequent viewgraphs are summarized. The primary motivation behind this presentation is to observe that certain macroscopic, microscopic, and submicroscopic phenomena are being understood that have basic influence on understanding the durability and high temperature sensitivity of polymers and polymer-based composites. This understanding covers important issues of long term stability with respect to residual stresses and deformations which can have very deleterious effects on structures used for long periods of time as a result of the heat-involving manufacturing process. Beyond this, important progress is being made in understanding the nonlinear material response of polymers in the fracture context, because the nonlinear mechanics of the material at the tip of a crack, either propagating or ready to do so, is being understood with increasing precision.

Knauss, Wolfgang G.↗
NASA NTRS1992

Viscoelastic Response Of A Highly Filled Polymer

Report describes experimental and theoretical studies of nonlinear viscoelastic response of elastomeric binder material filled with small particles of different material. Studies characterize response with sufficient accuracy for use in designing parts subjected to high strains.

Peng, Steven T. J.↗
NASA NTRS1988

Transient response of joint dominated space structures - A new linearization technique

The linearization method presented for calculating the transient responses of nonlinear systems due to initial disturbances is an extension of the 'describing function' approach, in which the system's steady-state response is calculated by representing such nonlinear elements as space structure joints with impedances that are functions of response amplitude. It is shown that, for the transient case, the steady-state impedances can be averaged over the range of responses in order to furnish equivalent values of stiffness and damping; these, for a given set of initial displacements, may be treated as constant during calculations of system response.

Foelsche, G. A.↗
NASA NTRS1987

Response of joint dominated space structures

An efficient linearization method is presented for calculating the transient response of nonlinear systems due to initial disturbances. The method is an extension of the describing function approach in which the steady state response of the system is calculated by representing the nonlinear element, typically joints in the case of space structures, by impedances which are functions of the amplitude of response. Thus, the problem of solving the differential equation for the steady state response becomes one of solving a set of nonlinear algebraic equations involving the steady state amplitudes and phases of the system. It is shown that for the transient case the steady state impedances can be averaged over the range of responses in order to provide equivalent values of stiffness and damping that, for a given set of initial displacements, may be treated as being constant for purposes of calculating system response. Single degree of freedom system are used to demonstrate the method and to develop an approach for optimizing the joint's characteristics so as to minimize transient response times. The use of this method for response estimation and optimization in multiple degree of freedom systems is investigated.

Source record↗
NASA NTRS1975

Transfer function verification and block diagram simplification of a very high-order distributed pole closed-loop servo by means of non-linear time-response simulation

Linear frequency domain methods are inadequate in analyzing the 1975 Viking Orbiter (VO75) digital tape recorder servo due to dominant nonlinear effects such as servo signal limiting, unidirectional servo control, and static/dynamic Coulomb friction. The frequency loop (speed control) servo of the VO75 tape recorder is used to illustrate the analytical tools and methodology of system redundancy elimination and high order transfer function verification. The paper compares time-domain performance parameters derived from a series of nonlinear time responses with the available experimental data in order to select the best possible analytical transfer function representation of the tape transport (mechanical segment of the tape recorder) from several possible candidates. The study also shows how an analytical time-response simulation taking into account most system nonlinearities can pinpoint system redundancy and overdesign stemming from a strictly empirical design approach. System order reduction is achieved through truncation of individual transfer functions and elimination of redundant blocks.

Mukhopadhyay, A. K.↗
NASA NTRS1975

Combustion instability with partial length acoustic liners

The development is discussed of analytical techniques and numerical methods for the prediction of the stability behavior of liquid propellant rocket combustors with partial length acoustic liners, injector face baffles, and nonlinear combustion responses. Three primary objectives included: (1) extension of the Green's Function integral-iteration technique previously developed so that nonlinear three dimensional wave propagation effects could be included in stability predictions; (2) development of an analytical technique and a computer program for the prediction of the damping effects caused by injector face baffles; and (3) inclusion of a nonlinear, wave distortation dependent, combustion response model in the global stability analysis and determination of its effect on combustor stability.

Mitchell, C. E.↗
NASA NTRS1982

Nonlinear analysis of rotor-bearing systems using component mode synthesis

The method of component mode synthesis is developed to determine the forced response of nonlinear, multishaft, rotor-bearing systems. The formulation allows for simulation of system response due to blade loss, distributed unbalance, base shock, maneuver loads, and specified fixed frame forces. The motion of each rotating component of the system is described by superposing constraint modes associated with boundary coordinates and constrained precessional modes associated with internal coordinates. The precessional modes are truncated for each component and the reduced component equations are assembled with the nonlinear supports and interconnections to form a set of nonlinear system equations of reduced order. These equations are then numerically integrated to obtain the system response. A computer program, which is presently restricted to single shaft systems, has been written and results are presented for transient system response associated with blade loss dynamics with squeeze film dampers, and with interference rubs.

Nelson, H. D.↗
NASA NTRS1980

User's manual to the ACTION computer code

The form and interpretation of input and output data are defined. The Analysis of Crash Transients in Inelastic and Geometrically Nonlinear structures program (ACTION) performs nonlinear transient response analysis of structures subjected to time varying loads, allowing for nonlinear, time independent material properties and large geometry changes.

Kamat, M. P.↗
NASA NTRS1971

Some heuristic procedures for analyzing random vibration of nonlinear oscillators.

The stationary response of a lightly damped nonlinear oscillator subjected to wideband random excitation can be examined as an example of thermal equilibrium. It may be assumed that the response consists of a series of free-vibration cycles with small random fluctuations in phase and amplitude. Certain statistical properties of the response can be estimated by averaging corresponding properties of the free vibration with respect to cycle amplitude distributions. Such heuristic procedures for determining the expected frequency and the autocorrelation function of the stationary response are outlined. Some additional results concerning first-passage problems for nonlinear oscillators are included.

Crandall, S. H.↗
NASA NTRS1998

High Strain Rate Deformation Modeling of a Polymer Matrix Composite: Matrix Constitutive Equations - Part 1

Recently applications have exposed polymer matrix composite materials to very high strain rate loading conditions, requiring an ability to understand and predict the material behavior under these extreme conditions. In this first paper of a two part report, background information is presented, along with the constitutive equations which will be used to model the rate dependent nonlinear deformation response of the polymer matrix. Strain rate dependent inelastic constitutive models which were originally developed to model the viscoplastic deformation of metals have been adapted to model the nonlinear viscoelastic deformation of polymers. The modified equations were correlated by analyzing the tensile/ compressive response of both 977-2 toughened epoxy matrix and PEEK thermoplastic matrix over a variety of strain rates. For the cases examined, the modified constitutive equations appear to do an adequate job of modeling the polymer deformation response. A second follow-up paper will describe the implementation of the polymer deformation model into a composite micromechanical model, to allow for the modeling of the nonlinear, rate dependent deformation response of polymer matrix composites.

Goldberg, Robert K.↗