Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “multi material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Modeling the Interaction of Laser-Produced Proton Beams with Matter

A major goal of this project is to significantly increase our understanding of isochoric heating of matter using laser produced proton beams, and the associated high energy density (HED) and warm dense matter (WDM) regimes generated. This will benefit research fields such as planetary science, fusion energy, plasma physics, and material science. For example, it will enhance our understanding of WDM properties of iron and silica under conditions encountered in planetary interiors and diagnostic components in fusion devices exposed to high fluxes of energetic plasma ions. The project is motivated by recent experiments that irradiated Si targets with proton beams generated by the 20 TW-laser at the SLAC MEC end-station. The HED/WDM states are probed using the 50 fs hard X-rays available in the 3rd harmonic of the LCLS. As part of this project, results from the phase contrast X-ray imaging, which shows the generation of compression waves that produces rear surface spallation, are compared with results from the 3D multi-physics multi- material code, PISALE, that combines Arbitrary Lagrangian-Eulerian (ALE) hydrodynamics with Adaptive Mesh Refinement (AMR). This comparison required modifications to several physics models in the PISALE (Pacific Island Structured-AMR with ALE) code. An important aspect of this project is the continued training of graduate students in HED physics and in conducting complex multiphysics simulations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Novel Techniques for Millimeter-Wave Packages

A new millimeter-wave package architecture with supporting electrical, mechanical and material science experiment and analysis is presented. This package is well suited for discrete devices, monolithic microwave integrated circuits (MMIC's) and multichip module (MCM) applications. It has low-loss wide-band RF transitions which are necessary to overcome manufacturing tolerances leading to lower per unit cost Potential applications of this new packaging architecture which go beyond the standard requirements of device protection include integration of antennas, compatibility to photonic networks and direct transitions to waveguide systems. Techniques for electromagnetic analysis, thermal control and hermetic sealing were explored. Three dimensional electromagnetic analysis was performed using a finite difference time-domain (FDTD) algorithm and experimentally verified for millimeter-wave package input and output transitions. New multi-material system concepts (AlN, Cu, and diamond thin films) which allow excellent surface finishes to be achieved with enhanced thermal management have been investigated. A new approach utilizing block copolymer coatings was employed to hermetically seal packages which met MIL STD-883.

Herman, Martin I.↗

Vehicle Lightweighting: Mass Reduction Spectrum Analysis and Process Cost Modeling

The U.S. Department of Energy’s Vehicle Technologies Office, Materials area commissioned a study to model and assess manufacturing economics of alternative design and production strategies for a series of lightweight vehicle concepts. In the first two phases of this effort examined combinations of strategies aimed at achieving strategic targets of 40% and a 45% mass reduction relative to a standard North American midsize passenger sedan at an effective cost of $3.42 per pound (lb) saved. These results have been reported in the Idaho National Laboratory report INL/EXT-14-33863 entitled Vehicle Lightweighting: 40% and 45% Weight Savings Analysis: Technical Cost Modeling for Vehicle Lightweighting published in March 2015. The data for these strategies were drawn from many sources, including Lotus Engineering Limited and FEV, Inc. lightweighting studies, U.S. Department of Energy-funded Vehma International of America, Inc./Ford Motor Company Multi-Material Lightweight Prototype Vehicle Demonstration Project, the Aluminum Association Transportation Group, many United States Council for Automotive Research’s/United States Automotive Materials Partnership LLC lightweight materials programs, and IBIS Associates, Inc.’s decades of experience in automotive lightweighting and materials substitution analyses.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Indefinite materials

A compensating multi layer material includes two compensating layers adjacent to one another. A multi-layer embodiment of the invention produces subwavelength near-field focusing, but mitigates the thickness and loss limitations of the isotropic “perfect lens”. An antenna substrate comprises an indefinite material.

Smith, David R.↗

Indefinite materials

A compensating multi layer material includes two compensating layers adjacent to one another. A multi-layer embodiment of the invention produces sub-wavelength near-field focusing, but mitigates the thickness and loss limitations of the isotropic “perfect lens.” An antenna substrate comprises an indefinite material.

Smith, David R.↗

Adhesively-bonded Metal-CFRTP Bi-materials: Enhanced Crack Growth Resistance via Plasma and Quantified Fracture via Size Effect Method

This work investigated air plasma effect on the Mode I crack growth resistance of adhesively-bonded metal-CFRTP dissimilar joints by using aluminum alloy (AA6061) and short-carbon-fiber-reinforced polyamide 66 (CFRPA66) as an example, and the Double Cantilever Beam (DCB) fracture testing as an evaluation method. The results show that air plasma treatment can significantly improve the fracture resistance of adhesively-bonded AA6061-CFRPA66 dissimilar joints with about 140% enhanced Mode I fracture energy in maximum compared to non-treated ones. The quantified fracture energies from size effect method for both non-treated and plasma-treated cases are geometry-independent, whereas this is not true for modified beam theory causing geometry-dependent results. The foregoing improvement was confirmed from the failure surface morphology of plasma-treated specimens, showing fibers peeling off from CFRPA66 surface due to plasma-enhanced bonding between CFRPA66 and adhesive by the formation of covalent bonds at their interface. This study demonstrated air plasma as an efficient surface modification method to enhance the fracture resistance of adhesively-bonded metal-CFRTP dissimilar joints, and size effect method as a characterization method to properly quantify their fracture properties. These aspects are valuable in the area of multi-materials joining.

Plasma, Adhesive Bonding, Slow Crack Growth, fract↗

Numerical simulation of compressible fluid-dynamics in the chamber of inertial fusion energy systems

Here, this paper aims to establish new and innovative modeling capabilities for analyzing chambers in Inertial Fusion Energy (IFE) systems. IFE is emerging as a promising method to achieve fusion power production, but several challenges must be overcome to develop an IFE pilot plant or deploy commercial IFE systems. These challenges are both theoretical and technical, encompassing a deeper understanding of the underlying physical phenomena and the development of new technologies and materials. One of the needs is to develop mathematical models to describe IFE systems and numerical tools to simulate them. This paper contributes to this endeavor by presenting a new OpenFOAM solver for IFE systems, focusing on gas dynamics in their chambers. The analysis and development of chamber designs will play a significant role in the transition from single-shot experiments to high-repetition rates, as there is a need to protect the chamber walls from the intense radiation fields produced by fusion reactions. A promising design option, normally referred to as thick wall chamber design, consists in using lithium or molten salt jet arrays within the chamber. A critical phenomenon is the venting of high-pressure gases from the center to the external part of the chamber, passing through the blanket array. This process involves the propagation and attenuation of strong pressure waves, requiring suitable modeling approaches for compressible fluid-dynamics. The solver proposed in this work implements a multi-material hydrodynamics model tailored to accurately describe the non-linear propagation of pressure waves while avoiding numerical oscillation issues typical of high-velocity compressible simulation. This solver is verified against numerical test cases, validated against experimental data, and applied to the analysis of the High-Yield Lithium-Injection Fusion-Energy (HYLIFE-I) concept. The relevance of this paper is threefold. Firstly, it contributes to developing and testing modeling approaches for compressible fluid-dynamics phenomena, with specific focus on the new and unexplored topic of IFE thick-liquid-wall blanket modeling. Secondly, it marks one of the first applications of the OpenFOAM library in the research field of IFE systems. Finally, the investigated problem is of practical interest for IFE developers, as it provides useful indications about relevant phenomena in pressure wave propagation in the chamber of these systems.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Additive manufacturing of LiNi 1/3 Mn 1/3 Co 1/3 O 2 battery electrode material via vat photopolymerization precursor approach

Additive manufacturing, also called 3D printing, has the potential to enable the development of flexible, wearable and customizable batteries of any shape, maximizing energy storage while also reducing dead-weight and volume. In this work, for the first time, three-dimensional complex electrode structures of high-energy density LiNi 1/3 Mn 1/3 Co 1/3 O 2 (NMC 111) material are developed by means of a vat photopolymerization (VPP) process combined with an innovative precursor approach. This innovative approach involves the solubilization of metal precursor salts into a UV-photopolymerizable resin, so that detrimental light scattering and increased viscosity are minimized, followed by the in-situ synthesis of NMC 111 during thermal post-processing of the printed item. The absence of solid particles within the initial resin allows the production of smaller printed features that are crucial for 3D battery design. The formulation of the UV-photopolymerizable composite resin and 3D printing of complex structures, followed by an optimization of the thermal post-processing yielding NMC 111 is thoroughly described in this study. Based on these results, this work addresses one of the key aspects for 3D printed batteries via a precursor approach: the need for a compromise between electrochemical and mechanical performance in order to obtain fully functional 3D printed electrodes. In addition, it discusses the gaps that limit the multi-material 3D printing of batteries via the VPP process.

25 ENERGY STORAGE↗

The Roles of Interface, Adherend, and Adhesive in Plasma- and Other-treated Joints of Metals and FRP Materials Under Shear Deformation

This work investigated the role of interface, adherend, and adhesive in adhesively-bonded metal-metal, metal-CFRTP, and CFRTP-CFRTP combinations with plasma-treated surfaces under shear deformation. To this end, aluminum alloys (AA5052 and AA6061) and short-carbon-fiber-reinforced polyamide 66 (CFRPA66) were used as examples and performed through single lap shear testing. The results showed that air plasma surface treatment can improve the shear behavior of adhesively-bonded AA5052-CFRPA66 and CFRPA66-CFRPA66 joints with about 20% enhanced lap shear strength compared to non-treated cases. Failure surface morphology of plasma-treated CFRPA66 adherend confirmed this improvement by showing an increased amount of adhesive failure than interfacial failure between CFRPA66 and adhesive. But this is not true for AA5052-AA6061 joints with plasma-treated surfaces exhibiting almost no enhanced lap shear strength. This study also showed the importance of selecting a proper surface modification method for the enhancement of adhesive-bonded structures under shear deformation through the analysis of the results in this study and in the literature. For fiber-reinforced polymers (FRPs), improving FRP/adhesive interface may be prioritized via different surface modification methods (e.g., plasma, chemical coating, etc.) than adhesive modification methods. However, for surface-cleaned metals, toughening adhesive via different enhancement methods (e.g., nano-particles, chemical enhancement, etc.) may be more important than improving metal/adhesive interface. These insightful results are valuable in the area of multi-materials joining.

Qiao, Yao↗

Temporally Stable Supramolecular Polymeric Salts Enabling High-Performance 3D All-Aromatic Polyimide Lattices

Vat photopolymerization (VP) Additive Manufacturing (AM), in which UV light is selectively applied to cure photo-active polymers into complex geometries with micron-scale resolution, has a limited selection of aliphatic thermoset materials that exhibit relatively poor thermal performance. Ring-opening dianhydrides with acrylate-containing nucleophiles yielded diacrylate ester-dicarboxylic acids that enabled photo-active polyimide (PI) precursors, termed polysalts, upon neutralization with an aromatic diamine in solution. In situ FTIR spectroscopy coupled with a solution and photo-rheological measurements revealed a previously unknown time-dependent instability of 4,4'-oxydianiline (ODA) polysalts due to an aza-Michael addition. Replacement of the electron-donating ether-containing diamine with an electron withdrawing sulfone-containing monomer, e.g., 4,4'-diaminodiphenyl sulfone (DDS), prohibited the aza-Michael addition of the aromatic amine to the activated acrylate double bond. Novel DDS polysalt photocurable solutions are similarly analyzed and validated long-term stability, which enabled reproducible printing of polyimide organogel intermediates. Subsequent VP AM afforded 3-dimensional (3D) structures of intricate complexity and excellent surface finish, as demonstrated with scanning electron microscopy. In addition, the novel PMDA-HEA/DDS solution enabled the production of the first beam latticed architecture comprised of all-aromatic polyimide. Finally, the versatility of a polysalt platform for multi-material printing is further demonstrated by printing parts with alternating polysalt compositions.

36 MATERIALS SCIENCE↗

TU-F-18A-04: Use of An Image-Based Material-Decomposition Algorithm for Multi-Energy CT to Determine Basis Material Densities

Purpose: Published methods for image-based material decomposition with multi-energy CT images have required the assumption of volume conservation or accurate knowledge of the x-ray spectra and detector response. The purpose of this work was to develop an image-based material-decomposition algorithm that can overcome these limitations. Methods: An image-based material decomposition algorithm was developed that requires only mass conservation (rather than volume conservation). With this method, using multi-energy CT measurements made with n=4 energy bins, the mass density of each basis material and of the mixture can be determined without knowledge of the tube spectra and detector response. A digital phantom containing 12 samples of mixtures from water, calcium, iron, and iodine was used in the simulation (Siemens DRASIM). The calibration was performed by using pure materials at each energy bin. The accuracy of the technique was evaluated in noise-free and noisy data under the assumption of an ideal photon-counting detector. Results: Basis material densities can be estimated accurately by either theoretic calculation or calibration with known pure materials. The calibration approach requires no prior information about the spectra and detector response. Regression analysis of theoretical values versus estimated values results in excellent agreement for both noise-free and noisy data. For the calibration approach, the R-square values are 0.9960+/−0.0025 and 0.9476+/−0.0363 for noise-free and noisy data, respectively. Conclusion: From multi-energy CT images with n=4 energy bins, the developed image-based material decomposition method accurately estimated 4 basis material density (3 without k-edge and 1 with in the range of the simulated energy bins) even without any prior information about spectra and detector response. This method is applicable to mixtures of solutions and dissolvable materials, where volume conservation assumptions do not apply. CHM receives research support from NIH and Siemens Healthcare.

62 RADIOLOGY AND NUCLEAR MEDICINE↗

Shape optimization using a NURBS-based interface-enriched generalized FEM

This study presents a gradient-based shape optimization over a fixed mesh using a non-uniform rational B-splines-based interface-enriched generalized finite element method, applicable to multi-material structures. In the proposed method, non-uniform rational B-splines are used to parameterize the design geometry precisely and compactly by a small number of design variables. An analytical shape sensitivity analysis is developed to compute derivatives of the objective and constraint functions with respect to the design variables. Subtle but important new terms involve the sensitivity of shape functions and their spatial derivatives. As a result, verification and illustrative problems are solved to demonstrate the precision and capability of the method.

42 ENGINEERING↗

Adaptive immersed isogeometric level-set topology optimization

Here, this paper presents for the first time an adaptive immersed approach for level-set topology optimization using higher-order truncated hierarchical B-spline discretizations for design and state variable fields. Boundaries and interfaces are represented implicitly by the iso-contour of one or multiple level-set functions. An immersed finite element method, the eXtended IsoGeometric Analysis, is used to predict the physical response. The proposed optimization framework affords different adaptively refined higher-order B-spline discretizations for individual design and state variable fields. The increased continuity of higher-order B-spline discretizations together with local refinement enables direct control over the accuracy of the representation of each field while simultaneously reducing computational cost compared to uniformly refined discretizations. A flexible mesh adaptation strategy enables local refinement based on geometric measures or physics-based error indicators. These adaptive discretization and analysis approaches are integrated into gradient-based optimization schemes, evaluating the design sensitivities using the adjoint method. Numerical studies illustrate the features of the proposed framework with static, linear elastic, multi-material, two- and three-dimensional problems. The examples provide insight into the effect of refining the design variable field on the optimization result and the convergence rate of the optimization process. Using coarse higher-order B-spline discretizations for level-set fields promotes the development of smooth designs and suppresses the emergence of small features. Moreover, adaptive mesh refinement for state variable fields results in a reduction of overall computational cost. Higher-order B-spline discretizations are especially interesting when evaluating gradients of state variable fields due to their higher inter-element continuity.

36 MATERIALS SCIENCE↗

Investigation of Droplet Deposition for Suspensions Usable for Thermoplastic 3D Printing (T3DP)

Thermoplastic 3D printing (T3DP) is an additive manufacturing (AM) technology, which can be used for the production of dense single- and especially multi-material components. This becomes possible because of the combination of the precise deposition of small droplets of molten thermoplastic suspensions containing ceramic or metal particles, and a curing mechanism caused on cool down increasing the viscosity. In this paper, the droplet formation behavior of zirconia suspensions for T3DP (82 and 84 wt.%) was investigated. The droplet fusion factor (dff) is introduced to calculate the necessary distance between two droplets to form filament-like structures by fusion of adjacent droplets. Filament-like structures with a smooth surface and a nearly homogeneous cross section were manufactured for both suspensions with a dff of 44% or higher.

36 MATERIALS SCIENCE↗

Modification of Jet Velocities in an Explosively Loaded Copper Target with a Conical Cavity

Here, in this work, the design and execution of an experiment with the goal of demonstrating control over the evolution of a copper jet is described. Simulations show that when using simple multi-material buffers placed between a copper target with a conical cavity and a cylinder of high-explosive, a variety of jetting behaviors occur based on material placement, including both jet velocity augmentation and mitigation. A parameter sweep was performed to determine optimal buffer designs in two configurations. Experiments using the optimal buffer designs verified the effectiveness of the buffers at altering jet velocities. Similar trends were shown between the experimental results and the modeling.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Achieving Metallurgical Bonding in Aluminum/Steel Bimetallic Castings

Abstract Aluminum castings are increasingly being used in automotive powertrain and structural applications for vehicle lightweighting. Cast aluminum parts often need to be machined and joined to steel components in multi-material systems. Bimetallic components produced by casting aluminum over steel substrate are advantageous due to the elimination of machining and traditional dissimilar material joining processes. However, forming a strong metallurgical bonding during overcasting process has been challenging. In this paper, the effects of processing conditions such as substrate surface preparation, pre-heating temperature, melt conditions as well as casting design were studied by investigating the bimetallic interfaces for aluminum A319 casting alloy and a high alloy steel substrate in a sand-casting process. Zn and Al-based substrate coatings were evaluated. The experimental results suggest a metallurgical bond between aluminum and steel can be formed during the sand-casting process via high temperature diffusion with or without coatings. Al-based substrate coating prior to overcasting results in the formation of a continuous layer of intermetallics at the bimetallic interface, with large Al–Si–Fe intermetallics penetrating the cast aluminum.

Moodispaw, Michael P. (ORCID:0000000267635882)↗

Additive manufacturing of two-phase lightweight, stiff and high damping carbon fiber reinforced polymer microlattices

Carbon fiber reinforced polymer (CFRP) composite is known for its high stiffness-to-weight ratio and hence is of great interest in several engineering fields such as aerospace, automotive, defense, etc. However, such a composite is not suitable for energy dissipation as failure occurs with very little or no plastic deformation. Herein, we present an extendable multi-material projection microstereolithography process capable of producing carbon-fiber-reinforced cellular materials that achieve simultaneously high specific stiffness and damping coefficient. Inspired by the upper bounds of stiffness-loss coefficient in a two-phase composite, we designed and additively manufactured CFRP microlattices with soft phases architected into selected stiff-phase struts. Our results, confirmed by experimental and analytical calculations, revealed that the damping performance can be significantly enhanced by the addition of only a small fraction of the soft phase. The presented design and additive manufacturing strategy allow for optimizing mutually exclusive properties. As a result, these CFRP microlattices achieved high specific stiffness comparable to commercial CFRP, technical ceramics, and composites, while being dissipative like elastomers.

36 MATERIALS SCIENCE↗

Laser powder bed fusion of Inconel 718 on 316 stainless steel

The joining of Inconel 718 and 316 stainless steel has notable industrial importance. However, traditional arc-welding has many issues. In particular, the formation of the detrimental Nb-rich Laves phase in the heat affected zone can promote crack initiation and propagation, which leads to poor mechanical properties. The small heat input and the rapid solidification of laser powder bed fusion (PBF) has the potential to suppress this problem. Despite the infancy of the multi-material PBF, it is of interest to investigate the relationship among the process parameter, the microstructure at the materials joining point, and the mechanical performance. In this study, we used high-speed x-ray imaging to in-situ monitor the printing of Inconel 718 tracks on a 316H SS substrate via laser powder bed fusion, followed by post-build characterization and testing with SEM, XRD and nanoindentation. We observed that a higher linear energy density resulted in a more diffused interface and a smaller compositional gradient, but as a trade-off, generated more keyhole pores and thermal cracks. Furthermore, we also showed that the built layer exhibited chemical inhomogeneity at two length scales: a tens-of-mu m-scale compositional vortex due to the melt flow, and a sub-mu m-scale Nb-rich dendritic structure due to the non-equilibrium solidification that led to the formation of the Laves phase. It was inferred that the chemical inhomogeneity may benefit the mechanical properties at the interface by providing more interlocking between the two materials and also by limiting the effect of the brittle Laves phase to potentially short range.

36 MATERIALS SCIENCE↗