Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “molecular electronics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Some optical and electron microscope comparative studies of excimer laser-assisted and nonassisted molecular-beam epitaxically grown thin GaAs films on Si

The quality of GaAs thin films grown via MBE under pulsed excimer laser irradiation on Si substrates is examined in both laser-irradiated and nonirradiated areas using Raman scattering, Rayleigh scattering, and by photoluminescence (PL), as a function of temperature, and by TEM. The temperature dependence of the PL and Raman peak positions indicates the presence of compressive stress in the thin GaAs films in both laser-irradiated and nonirradiated areas. This indicates incomplete homogeneous strain relaxation by dislocations at the growth temperature. The residual compressive strain at the growth temperature is large enough such that even with the introduction of tensile strain arising from the difference in thermal expansion coefficients of GaAs and Si, a compressive strain is still present at room temperature for these thin GaAs/Si films.

Lao, Pudong↗
NASA NTRS2005

Diode Laser Sensors for Arc-Jet Characterization

The development and application of tunable diode laser (TDL) absorption sensors to monitor the health and operating conditions in the large-scale 60 MW arc-heated- plasma wind-tunnel at NASA Ames Research Center is reported. The interactive heating facility (THF) produces re-entry flow conditions by expanding the gas heated in a constricted plasma arc-heater to flow at high velocity over a model located in a test cabin. This facility provides the conditions needed to test thermal protective systems for spacecraft re-entering the earth s atmosphere. TDL sensors are developed to monitor gas flows in both the high-temperature constricted flow and the supersonic expansion flow into test cabin. These sensors utilize wavelength-tuned diode lasers to measure absorption transitions of atomic oxygen near 777.2 nm, atomic nitrogen near 856.8 nm, and atomic copper near 793.3 nm. The oxygen and nitrogen sensors measure the population density in exited electronic states of these atoms. The measurements combined with the assumption of local thermal and chemical equilibrium yield gas temperature (typically near 7,000K). The nitrogen and oxygen population temperatures are redundant, and their close agreement provides an important test of the local thermal equilibrium assumption. These temperature sensors provide time-resolved monitors of the operating conditions of the arc-heater and can be used to verify and control the test conditions. An additional TDL sensor was developed to monitor the copper concentration in the arc-heater flow yielding values as high as 13 ppm. Measurements of copper in the flow can identify flow conditions with unacceptably rapid electrode erosion, and hence this sensor provides valuable information needed to schedule maintenance to avoid costly arc-heater failure. TDL sensors were also developed for measurements in the test cabin, where absorption measurements of the populations of argon and molecular nitrogen in excited metastable electronic states established that the number density of these excited species is much lower than estimated using frozen-chemistry approximations. This key finding suggests that in the post-expansion region there is not a significant energy sequestration in electronically excited species. Finally, TDL measurements of atomic potassium seeded into the test cabin flow were used to directly measure the static temperature of the test gas. The results of this study illustrate the high potential of time-resolved TDL measurements for routine and economical sensing of arc-heater health (gas temperature and electrode erosion) as well as the time-resolved test-cabin-flow conditions in front of the model.

Hanson, Ronald K.↗
NASA NTRS1993

(abstract)Electron Impact Emission Cross Sections for Modeling UV Auroral and Dayglow Observations of the Upper Atmospheres of Planets

In the upper atmospheres of the Jovian and Terrestrial planets a dominant mechanism for energy transfer occurs through electron collisional processes with neutral species leading to UV radiation. In response to the need for accurate collision cross sections to model spectroscopic observations of planetary systems, JPL has measured in the laboratory emission cross sections and medium resolution spectra of H, H(sub 2), N(sub 2), SO(sub 2), and other important planetary gases.Voyager and International Ultraviolet Explorer (IUE) spacecraft have established that band systems of H(sub 2) and N(sub 2) are the dominant UV molecular emissions in the solar system produced by electron impact. Applications of our data to models of Voyager, IUE, Galileo, and Hubble Space Telescope observations of the planets will be described.

molecular emissions↗
NASA NTRS1995

Rotational And Rovibrational Energy Transfer In Electron Collisions With Molecules

Air flows around a hypervelocity reentry vehicle undergo dissociation, rovibrational excitation and ionization. More specifically the air, initially 80% N2 and 20% O2, in the shock layer consists of species such as N, O, N2, O2, NO, N+, O+, N+, O+, NO+ and 2 free electrons. It was pointed out in multi temperature models'' that the temperature of the rotational energy modes and the gas-kinetic translational temperature are quickly equilibrated by a few collisions and rise rapidly to high temperatures as 50000K before falling off to equilibrium value of 10000K. Contrary, the electronic and vibrational temperatures state energy distributions remain low (less than 15000K) because of the slow equilibration. Electron vibrational energy transfer is thought to play a crucial role in such a ionizing flow regime since chemical reaction rates and dissociation depend strongly on the vibrational temperatures. Modeling of these flowfields in principle require the rovibrational excitation and de-excitation cross section data for average electron energies from threshold up to several eV (leV=11605.4 K). In this lecture we focus on theoretical description of rotational effects i.e. energy transfer of electrons to molecules such that the molecular rotational (vojo goes to voj) or vibrational and rotational (v(sub 0)j(sub 0) goes to vj) states are changed. Excitation and de-excitation of electronic states was discussed in a previous talk at this conference.

Thuemmel, Helmar T.↗
NASA NTRS1981

Low-energy electron effects on tensile modulus and infrared transmission properties of a polypyromellitimide film

Infrared (IR) spectroscopy and tensile modulus testing were used to evaluate the importance of experimental procedure on changes in properties of pyromellitic dianhydride-p,p prime-oxydianiline film exposed to electron radiation. The radiation exposures were accelerated, approximate equivalents to the total dose expected for a 30 year mission in geosynchronous Earth orbit. The change in the tensile modulus depends more on the dose rate and the time interval between exposure and testing than on total dose. The IR data vary with both total dose and dose rate. A threshold dose rate exists below which reversible radiation effects on the IR spectra occur. Above the threshold dose rate, irreversible effects occur with the appearance of a new band. Post-irradiation and in situ IR absorption bands are significantly different. It is suggested that the electron radiation induced metastable, excites molecular states.

Ferl, J. E.↗
NASA NTRS1985

An investigation of molecular structure of copolymers using positron annihilation spectroscopy

Positron lifetime measurements were made in copolyimides synthesized from linear 4,4 prime-bis(3,4-dicarboxyphenoxy) diphenylsulfide dianhydride (BDSDA)/4,4 prime-diaminodiphenyl (ODA) and BDSDA/1,3-diaminobenzene (m-phenylene diamine) homopolymers. The probability of positronium formation as well as its subsequent lifetime are lower in the BDSDA/ODA/MPD (50-50) copolyimide, indicating the presence of a transition molecular architecture characterized by higher electron density and stronger bonds which permit both chemical as well as physical entry of water molecules into it. The presence of this transition region imparts unique physical and mechanical properties to the copolyimide.

Singh, J. J.↗
NASA NTRS1987

Results from the vehicle charging and potential experiment on STS-3

The Vehicle Charging and Potential Experiment formed part of the scientific experiments comprising the NASA Office of Space Sciences-1 pallet flown at an altitude of 250 km and an orbital inclination of 40 deg on the third flight of the Space Shuttle Orbiter in March 1982. Details of the objectives, the instrumentation of the experiment, and some preliminary results from the individual instruments are presented. The experiment studied passive vehicle charging using thermal plasma probes, and it is concluded that apart from moderate v x B (L)-induced electrical potential resulting from the large size and restricted plasma contact area, the Space Shuttle Orbiter behaved similarly to smaller spacecraft orbiting in the same ionospheric region. However, an unexpected passive orbital result was the detection of enhanced plasma density in the vicinity of the Orbiter under restricted orbital conditions, apparently composed of contaminant molecular species and with an electron component having a temperature considerably higher than the ambient ionosphere electrons. The active vehicle charging experiments were performed by using a 100 mA/1 keV electron beam emitted out of the payload bay. Charging measurements made during short electron beam pulse emissions provide an upper limit of about 1 mF for the Orbiter capacitance. Steady-state charging measurements showed that for the vehicle attitudes covered by the mission, the induced electrical potential was normally only a few volts, except during some nighttime conditions when it rose above 40 V.

Banks, P. M.↗
NASA NTRS1987

Effect of object potentials on the wake of a flowing plasma

The structure of the electric potential and ion density of the ion front in the near wake created by the flow of synthetic plasma past a conducting plate was investigated experimentally and numerically, with particular attention given to the effect of plate potential on the structure of the ion front. Results were obtained for a molecular nitrogen plasma with ambient electron densities of about 100,000/cu cm, ion temperatures of about 0.025 eV, electron temperatures of about 0.3 eV, and plasma flow velocities of about 10,000 m/s. Two-dimensional simulations of the laboratory experiments were performed by using a multiple waterbag technique. The calculated and experimental results show that wake closure is well described by the acceleration of ions in the plasma steady-state electric field. However, the ion-front motion is strongly affected by the imposed potential of the object creating the wake.

Katz, I.↗
NASA NTRS1989

Additives Lower Pickup Of Moisture By Polyimides

Series of new polyimide-processing additives decrease free volume and pickup of moisture in new 422 copolyimide. Physical properties of several copolyimides synthesized from linear BDSDA/ODA/MPD homopolymers investigated previously, by positron-annihilation spectroscopy, with results indicating copolyimides have unique transition molecular structure characterized by higher electron densities and stronger bonds. Transition structure permits both physical and chemical entry of water molecules into it.

St. Clair, Terry L.↗
NASA NTRS2000

Effect of Negative Ions on the Conductivity of the Titan Atmosphere

In an earlier paper, Borucki et al (1987) calculated the electrical conductivity and electrical charge on aerosols in Titan's atmosphere due to the ionization by galactic cosmic rays and electron precipitation from Saturn's magnetosphere. The lower atmosphere was predicted to be substantially more conducting than the atmospheres of Earth and Venus because of the high concentration of free electrons. The prediction of a high conductivity is based on the lack of electrophillic species which form negative ions with low mobility and which reduce the number of free electrons. At that time, no molecular species capable of forming negative ions in concentrations sufficient to perturb the atmospheric conductivity were identified. Recently, E. Bakes and her colleagues have been investigating the formation of nitrogenous macromolecules using quantum mechanical methods. Their calculations indicate that the molecules will be highly electrophillic and are likely to be present in the atmosphere at mixing ratios of order 10(exp -7). This mixing ratio is sufficiently large that a substantial reduction in the conductivity is expected at altitudes below 100 km. Revision of the atmospheric model to accommodate the presence of negative ions and to increase the fidelity of the modeling will be described.

Borucki, W. J.↗
NASA NTRS1999

Heats of Formation and Bond Energies in Group III Compounds

We present heats of formation and bond energies for Group-III compounds obtained from calculations of molecular ground-state I electronic energies. Data for compounds of the form MXn are presented, where M = B, Al, Ga, and In, X = He H, Cl, and CH3, and n = 1-3. Energies for the B, Al, and Ga compounds are obtained from G2 predictions, while those for the In compounds are obtained from CCSD(T)/CBS calculations; these are the most accurate calculations for indium-containing compounds published to date. In most cases, the calculated thermochemistry is in good agreement with published values derived from experiments for those species that have well-established heats of formation. Bond energies obtained from the heats of formation follow the expected trend (Cl much greater than CH3 approx. H). However, the CH3M-(CH3)2 bond energies obtained for trimethylgallium and trimethylindium are considerably stronger (greater than 15 kcal/mol) than currently accepted values.

Bauschlicher, Charles W., Jr.↗
NASA NTRS2008

Uncertainty Analysis of Air Radiation for Lunar Return Shock Layers

By leveraging a new uncertainty markup technique, two risk analysis methods are used to compute the uncertainty of lunar-return shock layer radiation predicted by the High temperature Aerothermodynamic Radiation Algorithm (HARA). The effects of epistemic uncertainty, or uncertainty due to a lack of knowledge, is considered for the following modeling parameters: atomic line oscillator strengths, atomic line Stark broadening widths, atomic photoionization cross sections, negative ion photodetachment cross sections, molecular bands oscillator strengths, and electron impact excitation rates. First, a simplified shock layer problem consisting of two constant-property equilibrium layers is considered. The results of this simplified problem show that the atomic nitrogen oscillator strengths and Stark broadening widths in both the vacuum ultraviolet and infrared spectral regions, along with the negative ion continuum, are the dominant uncertainty contributors. Next, three variable property stagnation-line shock layer cases are analyzed: a typical lunar return case and two Fire II cases. For the near-equilibrium lunar return and Fire 1643-second cases, the resulting uncertainties are very similar to the simplified case. Conversely, the relatively nonequilibrium 1636-second case shows significantly larger influence from electron impact excitation rates of both atoms and molecules. For all cases, the total uncertainty in radiative heat flux to the wall due to epistemic uncertainty in modeling parameters is 30% as opposed to the erroneously-small uncertainty levels (plus or minus 6%) found when treating model parameter uncertainties as aleatory (due to chance) instead of epistemic (due to lack of knowledge).

Kleb, Bil↗
NASA NTRS2011

Application of Emerging Pharmaceutical Technologies for Therapeutic Challenges of Space Exploration Missions

An important requirement of therapeutics for extended duration exploration missions beyond low Earth orbit will be the development of pharmaceutical technologies suitable for sustained and preventive health care in remote and adverse environmental conditions. Availability of sustained, stable and targeted delivery pharmaceuticals for preventive health of major organ systems including gastrointestinal, hepato-renal, musculo-skeletal and immune function are essential to offset adverse effects of space environment beyond low Earth orbit. Specifically, medical needs may include multi-drug combinations for hormone replacement, radiation protection, immune enhancement and organ function restoration. Additionally, extended stability of pharmaceuticals dispensed in space must be also considered in future drug development. Emerging technologies that can deliver stable and multi-therapy pharmaceutical preparations and delivery systems include nanotechnology based drug delivery platforms, targeted-delivery systems in non-oral and non-parenteral formulation matrices. Synthetic nanomaterials designed with molecular precision offer defined structures, electronics, and chemistries to be efficient drug carriers with clear advantages over conventional materials of drug delivery matricies. Nano-carrier materials like the bottle brush polymers may be suitable for systemic delivery of drug cocktails while Superparamagnetic Iron Oxide Nanoparticles or (SPIONS) have great potential to serve as carriers for targeted drug delivery to a specific site. These and other emerging concepts of drug delivery and extended shelf-life technologies will be reviewed in light of their application to address health-care challenges of exploration missions. Innovations in alternate treatments for sustained immune enhancement and infection control will be also discussed.

Putcha, Lakshmi↗
NASA NTRS1993

The (FHCl)- molecular anion - Structural aspects, global surface, and vibrational eigenspectrum

State of the art ab initio electronic structure methods have been used to investigate the (FHCl)- molecular anion. It is proposed that the geometric structure and binding energies of the complex are r(e)(H-F) = 0.963 +/- 0.003 A, R(e)(H-Cl) = 1.925 +/- 0.015 A, and D0(HF + Cl(-)) = 21.8 +/- 0.4 kcal/mol. A Morokuma decomposition of the ion-molecular bonding give the following electrostatic, polarization, exchange repulsion, dispersion, and charge-transfer plus higher-order mixing components of the vibrationless complexation energy: -27.3, -5.2, +18.3, -4.5, and -5.0 kcal/mol, respectively. A couples cluster single and doubles global surface is constructed from 208 and 228 energy points for linear and bent configurations, respectively, these being fit to rms errors of only 3.9 and 9.3/cm, respectively, below 8000/cm. Converged J = 0 and J = 1 variational eigenstates of the (FHCl)- surface to near the HF + Cl(-) dissociation threshold are determined. The fundamental vibrational frequencies are found to be nu1 = 247/cm, nu2 = 876/cm, and nu3 = 2884/cm. The complete vibrational eigenspectrum is analyzed.

Klepeis, Neil E.↗