Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “load factor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Flight loads and control

The prediction of flight loads and their potential reduction, using various control logics for the space shuttle vehicles, is very complex. Some factors, not found on previous launch vehicles, that increase the complexity are large lifting surfaces, unsymmetrical structure, unsymmetrical aerodynamics, trajectory control system coupling, and large aeroelastic effects. Discussed are these load producing factors and load reducing techniques. Identification of potential technology areas is included.

Mowery, D. K.↗
NASA NTRS1995

Aerosol effects and corrections in the Halogen Occultation Experiment

The eruptions of Mt. Pinatubo in June 1991 increased stratospheric aerosol loading by a factor of 30, affecting chemistry, radiative transfer, and remote measurements of the stratosphere. The Halogen Occultation Experiment (HALOE) instrument on board Upper Atmosphere Research Satellite (UARS) makes measurements globally for inferring profiles of NO2, H2O, O3, HF, HCl, CH4, NO, and temperature in addition to aerosol extinction at five wavelengths. Understanding and removing the aerosol extinction is essential for obtaining accurate retrievals from the radiometer channels of NO2, H2O and O3 in the lower stratosphere since these measurements are severely affected by contaminant aerosol absorption. If ignored, aerosol absorption in the radiometer measurements is interpreted as additional absorption by the target gas, resulting in anomalously large mixing ratios. To correct the radiometer measurements for aerosol effects, a retrieved aerosol extinction profile is extrapolated to the radiometer wavelengths and then included as continuum attenuation. The sensitivity of the extrapolation to size distribution and composition is small for certain wavelength combinations, reducing the correction uncertainty. The aerosol corrections extend the usable range of profiles retrieved from the radiometer channels to the tropopause with results that agree well with correlative measurements. In situations of heavy aerosol loading, errors due to aerosol in the retrieved mixing ratios are reduced to values of about 15, 25, and 60% in H2O, O3, and NO2, respectively, levels that are much less than the correction magnitude.

Hervig, Mark E.↗
NASA NTRS1973

Experimental study on optimization parameters of a supersonic jet ejector thrust augmentor.

The experimental data were aimed at obtaining the effect of jet mixing, the effective length/diameter of the ejector tube, the entrance length shape factor, the shape loading, and the optimum primary jet location. The total augmented thrust is proportional to the diameter of the ejector. The data show that for a practical design the entrance lip shape and the stream lines around the lip are also important in order to optimize the percentage augmentation.

Cheng, D. Y.↗
NASA NTRS1974

Analysis and synthesis of a fluid sonic pulse system

A nonlinear sonic system is described that includes a delay line. Short-lived pulses with a high repetition frequency circulate through the system. The analysis was carried out by defining the reflection factor at the load and then dividing the input pulse according to duration into sections of appropriate width. The response was determined for each section, the response to the whole pulse being given by the sum of the responses at the sections. This makes it possible to broach the synthesis of a sonic system that will give an output pulse of the desired form.

Boita, M.↗
NASA NTRS1978

Temperature control analysis and flight results for the Viking Orbiter 1975 Mars atmospheric water detection instrument

The Mars atmospheric water detector (MAWD) instrument required a temperature of -70 C at the detector. The monochromator housing required +20 C + or - 1 C. This instrument was located on the scan platform, and slewed across two solar panels. The thermal design for the detector was an open flat plate radiator thermally isolated on four 1-in. tubes, with a flexible strap to the detector. MAWD radiator view factors and heat loads from the spacecraft were determined for the Lander on and off, for all angular positions of the scan platform. Subsystem and system tests were performed using the 25-ft diameter solar simulator. In-flight results have shown no anomalies, and no degradation has been observed. Servo-controlled heaters are used to control the temperature.

Kavanagh, H. M.↗
NASA NTRS1973

User's instructions for the cardiovascular Walters model

The model is a combined, steady-state cardiovascular and thermal model. It was originally developed for interactive use, but was converted to batch mode simulation for the Sigma 3 computer. The model has the purpose to compute steady-state circulatory and thermal variables in response to exercise work loads and environmental factors. During a computer simulation run, several selected variables are printed at each time step. End conditions are also printed at the completion of the run.

Croston, R. C.↗
NASA NTRS1982

Thermal performance of a photographic laboratory process: Solar Hot Water System

The thermal performance of a solar process hot water system is described. The system was designed to supply 22,000 liters (5,500 gallons) per day of 66 C (150 F) process water for photographic processing. The 328 sq m (3,528 sq. ft.) solar field has supplied 58% of the thermal energy for the system. Techniques used for analyzing various thermal values are given. Load and performance factors and the resulting solar contribution are discussed.

Walker, J. A.↗
NASA NTRS1983

Fabrication division ultrasonic inspection specification for critically stressed components

An ultrasonic inspection specification which incorporates existing industry practices for straight beam modes with a new approach to the angle beam reference standard was developed. The method employs a commercially available letter "I" die stamp to impress a controlled shape ultrasonic reflector using common hand tools. The specification is designed to produce very stringent inspections and is primarily intended for utilization in the grading of material used in high load-low safety factor applications, such as cryogenic wind tunnel models and support hardware.

Berry, R. F., Jr.↗
NASA NTRS1987

Experimental study of shock wave interference heating on a cylindrical leading edge at Mach 6 and 8

This paper presents the details of an experimental study of shock wave interference heating on a cylindrical leading edge representative of the cowl of a rectangular hypersonic engine inlet. The study was conducted at Mach numbers of 6.3, 6.5 and 8.0. This study has provided the first (1) detailed pressure and heat transfer rate distributions for a two-dimensional shock wave interference on a cylinder and (2) insight into the effects of temperature dependent specific heats on the phenomena. The peak pressure and heat transfer rates were 10 times the undisturbed flow stagnation point levels. The peak levels and their gradients increased with Mach number. Variation in specific heats and hence the ratio of specific heats with temperature manifest in slightly lower loads and amplification factors than for corresponding perfect gas conditions.

Wieting, Allan R.↗
NASA NTRS1990

Optimum structural design of robotic manipulators with fiber reinforced composite materials

High-speed robotic arms with advanced structural characteristics can be fabricated from optimally tailored fiber reinforced composites. An integrated design methodology is presented for the optimal structural synthesis of composite robotic manipulators. Optimum configurations of ply angles and ply thicknesses are predicted for maximum structural end-effector stiffness and maximum end-effector load carrying capacity, without altering the geometric dimensions of the links. Multiple posture finite element-based static performance criteria are implemented. A new finite element has been developed for the modeling of tubular composite links. Unique features are the inclusion of shear effects and coupling between stretching and flexure. Numerical solutions are obtained via an efficient optimization algorithm. Applications to an existing SCARA-class manipulator illustrate the effectiveness of the method and demonstrate the dramatic influence of the multi-postural design criteria on the optimal design. For a filament wound structure using a high strength carbon fiber in a thermoplastic matrix, the resultant optimum ply configurations have increased the specific stiffness and specific load capacity by factors of 1.5 and 16, respectively, in comparison to identically sized aluminum links.

Saravanos, D. A.↗
NASA NTRS1991

Liquid hydrogen turbopump foil bearing

Space transfer vehicles and other power and propulsion systems require long-life turbopumps. Rolling element bearings used in current turbopumps do not have sufficient life for these applications. Process fluid foil bearings have established long life, with exceptional reliability, over a wide range of temperatures and fluids in many high-speed turbomachinery applications. However, liquid hydrogen turbopumps require high-load capacity bearings. An experimental study was conducted to measure foil journal bearing load capacity in liquid hydrogen, using a bearing designed specifically for cryogenic hydrogen turbopump applications. Additional performance parameters such as power loss, stability, cooling flow requirements, and bearing life were measured. These tests showed a load capacity safety factor of approximately 10 for liquid hydrogen turbopump applictions. These tests also demonstrated good rotor stability, low power loss and cooling flow, and long life.

Saville, M.↗
NASA NTRS1992

Structural development of Topex/Poseidon satellite

The Topex/Poseidon satellite's structural development approach adhered to more stringent requirements than previous efforts, since this spacecraft must withstand not only launch/flight loads but also those planned for the 'protoflight' vehicle's structural and environmental tests. There requirements encompassed conservatively estimated design loads, high safety factors, and extensive analytical simulations. The structural adequacy of the satellite was verified by means of a ground testing program to comply with both JPL institutional requirements and Arianespace requirements. Modal survey tests of the satellite have been successfully completed.

Lou, Michael C.↗
NASA NTRS1993

Probabilistic assessment of composite structures

A methodology and attendant computer code were developed and are used to computationally simulate the uncertain behavior of composite structures. The uncertain behavior includes buckling loads, stress concentration factors, displacements, stress/strain, etc., which are the consequences of the inherent uncertainties (scatter) in the primitive (independent random) variables (constituent, ply, laminate, and structural) that describe the composite structures. The computer code is IPACS (Integrated Probabilistic Assessment of Composite Structures). IPACS can simulate both composite mechanics and composite structural behavior. Application to probabilistic composite mechanics is illustrated by its use to evaluate the uncertainties in the major Poisson's ratio and in laminate stiffness and strength. IPACS' application to probabilistic structural analysis is illustrated by its used to evaluate the uncertainties in the buckling of a composite plate, the stress concentration factor in a composite panel, and the vertical displacement and ply stress in a composite aircraft wing segment. IPACS' application to probabilistic design is illustrated by its use to assess the thin composite shell (pipe).

Chamis, C. C.↗
NASA NTRS1945

An analysis of life expectancy of airplane wings in normal cruising flight

In order to provide a basis for judging the relative importance of wing failure by fatigue and by single intense gusts, an analysis of wing life for normal cruising flight was made based on data on the frequency of atmospheric gusts. The independent variables considered in the analysis included stress-concentration factor, stress-load relation, wing loading, design and cruising speeds, design gust velocity, and airplane size. Several methods for estimating fatigue life from gust frequencies are discussed. The procedure selected for the analysis is believed to be simple and reasonably accurate, though slightly conservative.

Putnam, Abbott A↗
NASA NTRS1993

IPACS (Integrated Probabilistic Assessment of Composite Structures): Code development and applications

A methodology and attendant computer code have been developed and are described to computationally simulate the uncertain behavior of composite structures. The uncertain behavior includes buckling loads, stress concentration factors, displacements, stress/strain etc., which are the consequences of the inherent uncertainties (scatter) in the primitive (independent random) variables (constituent, ply, laminate and structural) that describe the composite structures. The computer code, IPACS (Integrated Probabilistic Assessment of Composite Structures), can handle both composite mechanics and composite structures. Application to probabilistic composite mechanics is illustrated by its uses to evaluate the uncertainties in the major Poisson's ratio and in laminate stiffness and strength. IPACS application to probabilistic structural analysis is illustrated by its use to evaluate the uncertainties in the buckling of a composite plate, in the stress concentration factor in a composite panel and in the vertical displacement and ply stress in a composite aircraft wing segment.

Chamis, C. C.↗
NASA NTRS1991

An Evaluation of the Iosipescu Specimen for Composite Materials Shear Property Measurement

A detailed evaluation of the suitability of the Iosipescu specimen tested in the modified Wyoming fixture is presented. An experimental investigation using conventional strain gage instrumentation and moire interferometry is performed. A finite element analysis of the Iosipescu shear test for unidirectional and cross-ply composites is used to assess the uniformity of the shear stress field in the vicinity of the notch, and demonstrate the effect of the nonuniform stress field upon the strain gage measurements used for the determination of composite shear moduli. From the test results for graphite-epoxy laminates, it is shown that the proximity of the load introduction point to the test section greatly influences the individual gage readings for certain fiber orientations but the effect upon shear modulus measurement is relatively unimportant. A numerical study of the load contact effect shows the sensitivity of some fiber configurations to the specimen/fixture contact mechanism and may account for the variations in the measured shear moduli. A comparison of the strain gage readings from one surface of a specimen with corresponding data from moire interferometry on the opposite face documented an extreme sensitivity of some fiber orientations to eccentric loading which induced twisting and yielded spurious shear stress-strain curves. In the numerical analysis, it is shown that the Iosipescu specimens for different fiber orientations have to be modeled differently in order to closely approximate the true loading conditions. Correction factors are needed to allow for the nonuniformity of the strain field and the use of the average shear stress in the shear modulus evaluation. The correction factors, which are determined for the region occupied by the strain gage rosette, are found to be dependent upon the material orthotropic ratio and the finite element models. Based upon the experimental and numerical results, recommendations for improving the reliability and accuracy of the shear modulus values are made, and the implications for shear strength measurement discussed. Further application of the Iosipescu shear test to woven fabric composites is presented. The limitations of the traditional strain gage instrumentation on the satin weave and high tow plain weave fabrics is discussed. Test results of a epoxy based aluminum particulate composite is also presented. A modification of the Iosipescu specimen is proposed and investigated experimentally and numerically. It is shown that the proposed new specimen design provides a more uniform shear stress field in the test section and greatly reduces the normal and shear stress concentrations in the vicinity of the notches. While the fabrication and the material cost of the proposed specimen is tremendously reduced, it is shown the accuracy of the shear modulus measurement is not sacrificed.

Ho, Henjen↗
NASA NTRS1995

Stellar models with microscopic diffusion and rotational mixing. 1: Application to the Sun

The Yale stellar evolution code has been modified to include the combined effects of diffusion and rotational mixing on H-1, H-4, and the trace elements He, Li-6, Li-7, and Be-9. The interaction between rotational mixing and diffusion is studied by calculating a number of calibrated solar models. The rotational mixing inhibits the diffusion in the outer parts of the models, leading to a decrease in the envelope diffusion by 25%-50%. Conversely, diffusion leads to gradients in mean molecular weight which can inhibit the rotational mixing. The degree to which gradients in mean molecular weight inhibit the rotational mixing is somewhat uncertain. A comparison with the observed solar oblateness suggests that gradients in the mean molecular weight play a smaller role in inhibiting the rotational mixing than previously believed. This is reinforced by the fact that the model with the standard value for the inhibiting effect of mean molecular weight on the rotational mixing depletes no Li on the main sequence. This is clear in contrast to the observations. A reduction in the inhibiting effect of mean molecular weight gradients by a factor of 10 loads to noticeable main-sequence Li depletion.

Chaboyer, Brian↗