SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Individual current feeds enable better uniformity and flexible control. Separate contacts for lasers in array enable control of output radiation pattern and compensation of manufacturing nonuniformities among lasers. Concept of separate current control described for two-laser array in "Semiconductor Laser Phased Array" (NPO-15963).
Explore the source record for details and available documents.
The objective of this research work is to investigate the residual strains induced by the presence of a exit hole and internal hollow geometry present in a 3D printed IN718 similar to that seen in a gas turbine blade. The specimens were manufactured with an internal hollow structure that ended with an exit hole, and fabricated by direct metal laser sintering additive manufacturing technique. Using this technique, metal powder was melted by a laser source and rapidly cooled to form the part layer by layer. Rapid heating and cooling generate large thermal gradients and residual stresses in the 3D printed material. To be aligned with industry standards, specimens were heat-treated to relieve most of the residual stresses as well as to investigate whether IN718 still preserved a nonhomogeneous stress state after the thermal treatment. Roughness and microstructure analysis was performed to understand the heat-treated sample properties. To investigate the volumetric residual strain, the neutron diffraction technique was used with a definite neutron wavelength. Bragg’s law was used to determine lattice spacing. Interplanar lattice spacing and stress-free state lattice spacings were measured to calculate the strains. Residual strains were measured in the x and y direction to understand the impact of the presence of a exit hole and internal hollow geometry. The results of volumetric residual strain in the x and y directions showed no significant variations in the distribution of the strain due to the presence of a hollow structure as well as the exit hole. Overall, no significant stress concentration was observed in the heat treated sample. Sample geometry, instrumentation for neutron diffraction, and material properties are discussed in detail in this paper.
Additive manufacturing allows fabrication of custom-shaped thermoelectric materials while minimizing waste, reducing processing steps, and maximizing integration compared to conventional methods. Establishing the process-structure-property relationship of laser additive manufactured thermoelectric materials facilitates enhanced process control and thermoelectric performance. This research focuses on laser processing of bismuth telluride (Bi 2 Te 3 ), a well-established thermoelectric material for low temperature applications. Single melt tracks under various parameters (laser power, scan speed and number of scans) were processed on Bi 2 Te 3 powder compacts. A detailed analysis of the transition in the melting mode, grain growth, balling formation, and elemental composition is provided. Rapid melting and solidification of Bi 2 Te 3 resulted in fine-grained microstructure with preferential grain growth along the direction of the temperature gradient. Experimental results were corroborated with simulations for melt pool dimensions as well as grain morphology transitions resulting from the relationship between temperature gradient and solidification rate. Samples processed at 25 W, 350 mm/s with 5 scans resulted in minimized balling and porosity, along with columnar grains having a high density of dislocations.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
This report is a Milestone 2 deliverable in FY2025, under work package MT-25AN090211 to support research and qualification activities supported by the Advanced Materials and Manufacturing Technologies (AMMT) program. It provides an update on the work done on the laser based additive manufacturing of steels for nuclear applications, conducted collaboratively by Argonne National Laboratory and Pacific Northwestern National Laboratory. Building upon FY23 and FY24 efforts, the focus of FY25 includes continued optimization of process parameters for the alloys: A709 & G92. The work package also includes fabricating test samples to conduct a thorough microstructural analysis and perform preliminary mechanical testing. The major accomplishments of this work package are summarized below, applicable to both Laser Powder Bed Fusion (LPBF) processes conducted at Argonne National Laboratory and Laser Powder Directed Energy Deposition (LP-DED) processes conducted at Pacific Northwest National Laboratory.
As part of the advanced manufacturing (AM) focus of the Nuclear Energy Enabling Technologies (NEET) Advanced Sensors and Instrumentation (ASI) Program, new in-house capabilities to fabricate and test novel active and passive in-pile sensors are being developed at the Idaho National Laboratory (INL). These advanced-manufactured sensors, such as peak temperature monitors and strain gauges, must be miniaturized and be able to provide real-time feedback, all while withstanding the coupled extremes of temperature and radiation typically observed in the environment of a nuclear test reactor. Fabricating durable and robust in-pile sensors with high fidelity requires a fundamental understanding of the optimal process parameters required in the AM technique, as well as the effect of deviations from optimal process parameters on the sensor-substrate adhesion and the ultimate robustness of the sensor. This report presents the use of a laser-based, non-contact approach for characterizing the adhesion of sensors manufactured using aerosol jet printing (AJP) that comprise of silver nanoparticle inks deposited and sintered on austenitic stainless steel (SS) 316L substrates. The effect of substrate surface roughness, surface energy, ink sintering time and sintering temperature on the printed sensor topography and the sensor-substrate adhesion has been systematically investigated. The sensor-substrate interfacial adhesion strength was determined from the critical laser pulse energy required to ablate/ detach the printed sensor from the substrate. Measurements of the sensor topography using optical profilometry revealed that post-deposition sintering at 400°C for 60 minutes resulted in a reduced sensor thickness, while plasma treating the substrate prior to printing yielded sensors with uniform thickness profiles transverse to the print direction. Sintering temperature and time were found to be the dominant parameters that affected sensor-substrate adhesion, followed by substrate surface roughness. The laser-based and locally-destructive approach for adhesion strength measurements shows promise in overcoming the challenges and limitations of current standardized peel tests and can be developed into a post-fabrication process control protocol for evaluating the durability of AM printed sensors in a high throughput fashion. Future studies will investigate the use of laser-induced spallation techniques as well as non-destructive laser ultrasonic methods for sensor-substrate adhesion characterization on sensors manufactured using AJP and other AM techniques such as plasma jet printing (PJP).
Laser powder bed fusion (LPBF) Additive Manufacturing (AM) has the potential to enable the production of components with novel designs and material properties unachievable otherwise. However, process repeatability is a challenge, making qualification ill-defined and greatly reducing the utility of what could be an important manufacturing technology. In this work, a combination of modeling, uncertainty quantification (UQ), and experimentation are used in an effort to predict and bound the range of possible outcomes of the LPBF process. Quantities of interest predicted are melt pool dimensions, microstructure features, and mechanical distortions. A combination of high fidelity thermal-fluid models, microstructure growth models, and reduced fidelity, rapid thermal and mechanical models are used. Uncertainty propagation techniques are used to predict probability distributions of quantities of interest from estimates of process uncertainties. Repeated experiments are done to quantify observed probability distributions and compared to predicted distributions to determine if predictions are precise and accurate. Novel modeling methods are microstrucutre characterization techniques are also discussed. It is found that high fidelity models do a generally good job bounding experimentally observed melt pool morphologies for both bead-on-plate and powder bed cases. Microstructure models are able to bound a number of experimentally observed microstructure statistics, but with low precision due to challenges with calibrating the microstructure growth model parameters. A developed modified inherent strain distortion model does not accurately predict observed distortions. A lumped laser distortion model shows promise in being both accurately and precisely bounding observed outcomes from the deflection comb build, but requires further evaluation on more builds and geometries.
Metal parts produced by laser powder bed fusion (LPBF) additive manufacturing exhibit characteristic microstructures comparable to those observed in laser welding. The primary cause of this characteristic microstructure is rapid, localized heating and cooling cycles, which result in extreme thermal gradients where material solidification is followed by fast cooling in the solid state. The final microstructure and mechanical performance are also influenced by pore formation caused by melt pool fluid dynamics. Here, we use high speed, in situ X-ray diffraction to probe the kinetics of cooling and solid-solid phase transitions after laser melting in two aerospace titanium alloys: Ti-6Al-4V, an α + β alloy; and Ti-5Al-5V-5Mo-3Cr, a near-β alloy. We complement these diffraction studies with in situ X-ray imaging to probe melt pool dynamics and pore formation. From these two complementary probes, we quantify pore formation during melting and the subsequent microstructural evolution as the material rapidly cools after solidification. These results are critical for understanding defect formation and residual stress development in different titanium alloys under LPBF conditions and can help inform process models to predict final part performance.
In fluid flow, the frictional effects from interior surfaces of flow components create pressure loss across the surface. Understanding this inherent pressure loss due to friction and other phenomena is important when designing a flow system. For conventional manufacturing, friction loss has been empirically studied and is well known in the engineering community. However, newer manufacturing techniques, such as laser powder bed fusion (LPBF), an additive manufacturing technique, need to be understood. The inherent flow conditions resulting from the additive processes were studied. Test samples were printed with the flow path oriented in the vertical direction with different channel diameters to characterize the inherent fundamental flow properties of the process. Moody diagrams were replicated for a greater understanding of possibilities and shortfalls when implementing LPBF into design applications. Experimental flow testing revealed that greater effective sand grain roughness resulted from this process when compared to conventional machining methods. This roughness did not correlate well to the average roughness measured with a laser scanning microscope but was consistent with the average particle size of the powder metal feedstock.
This paper describes the inline (coaxial to laser) near infrared (NIR) camera sensor on the Configurable Architecture Additive Testbed (CAAT). The CAAT is an instrument that provides the capability to investigate laser based additive manufacturing (AM) processes and is configured for the metal powder bed fusion process. A low cost NIR camera is radiometrically calibrated to obtain coaxial, inline, imagery of laser generated melt pools. The camera capabilities, system optical path, and the uncertainty in the temperature measurement from NIR surface area scans on a bare titanium alloy plate are presented and discussed. The surface radiance measurements are compared to optical microscopy images of the melt pool width and depth. A metallic additive manufacturing process thermal model is developed in order to predict thermal distributions during laser scanning. The predicted thermal distributions by the model for different configurations are compared to the coaxial NIR measurements and discussed.
Directed energy deposition (DED) additive manufacturing (AM) is receiving growing attention in many applications, such as repair, remanufacturing, and fabrication of functionally graded structures. However, the laser-matter interactions and melt pool dynamics in laser DED with powder flow are still unclear, particularly in how pores form and flow inside the melt pool during the process. Understanding the porosity formation mechanisms is critical in the qualification, certification, and overall properties of a DED AM part. Porosity is a common phenomenon and can significantly hinder the quality of DED fabricated parts, as the pores can act as sites of crack nucleation and propagation. Here in this paper, we reveal four types of pore formation mechanisms through in-situ and operando high-speed high-resolution X-ray imaging in the DED AM process. Our results confirm that porosity within the feedstock powder induces pores in the process. We also observed pore formation mechanisms unique to the laser-based, powder-blown DED process as a result of powder delivery, keyhole dynamics, melt pool dynamics, and shield gas. High-speed X-ray images provide direct evidence for pore formation mechanisms and show that the pores related to the interaction between the delivered powder and melt pool are the largest in size in laser-based powder-blown DED AM. These results will guide porosity mitigation, elimination, and control in DED AM.
Improved lifetime of high-power broad area laser diodes will enhance their utility for manufacturing, scientific, and medical laser systems. However, factors contributing to gradual degradation of diode laser performance are not fully understood. Here we study the aging mechanisms of ~800 nm aluminum-free laser diodes grown by solid-source MBE. Oxygen was intentionally introduced at three different concentration levels into the quantum well (QW) and waveguide (WG) at concentrations <5×10 15 cm -3 . Diode power, slope efficiency (SE th ), threshold current (I th ), and device parameters such as QW and WG lifetimes were measured at discrete time steps throughout the aging run. The data show that lasing characteristics prior to aging are degraded by oxygen introduction, but the gradual power degradation rate of ~5% over 500 hours at current density 1.74 kA/cm 2 does not change with oxygen concentration. Aging-induced changes in nonradiative lifetimes and threshold were observed for shorter aging times, but stabilized after ~100 hrs. and cannot explain the observed power degradation. This suggests that gradual degradation in these devices is not due to nonradiative recombination at low levels of point defects. The data shows that this degradation results primarily from changes in slope efficiency, and simulation of these results suggests that the power degradation arises from increased intracavity absorption (ICA). Efforts to slow ICA growth, instead of efforts to control low levels of nonradiative recombination centers, may be the most fruitful path forward to improve laser diode lifetime.
Hybrid manufacturing is a promising route for producing complex aerospace components, yet systematic cost benchmarking across multiple additive-subtractive pathways remains limited. This study presents a comprehensive process-based cost analysis of seven hybrid manufacturing routes, including laser powder bed fusion (L-PBF), powder- and wire-directed energy deposition (DED), wire arc additive manufacturing (WAAM), additive friction stir deposition (AFSD), metal binder jetting (MBJ), and agility forging, followed by scanning and finish machining. Parametric cost models incorporating direct material, labor, and energy costs were developed. L-PBF results are discussed in detail for a pickle fork component and directly compared with commercial pricing. Across all hybrid routes, labor emerged as the dominant cost driver, contributing more than 70% of total manufacturing cost in some cases. AFSD exhibited the lowest cost for aluminum components, with MBJ being its 316 L stainless steel counterpart, after accounting for geometric scaling. Benchmarking against industrial quotes suggests that hybrid manufacturing can achieve cost levels comparable to those of commercial services, although labor-intensive processes exhibit greater deviation. The analysis highlights automation of material handling, setup, and supervision as key opportunities for improving economic competitiveness. Overall, the proposed framework provides a quantitative basis for evaluating and optimizing hybrid manufacturing pathways for aerospace applications.
We report the quality of parts produced through laser powder bed fusion additive manufacturing can be irregular, with complex geometries sometimes exhibiting dimensional inaccuracies and defects. For optimal part quality, laser process parameters should be selected carefully prior to printing and adjusted during the print if necessary. This is challenging since approaches to control and optimize the build parameters need to take into account the part geometry, the material, and the complex physics of laser powder bed fusion. This work describes a data-driven approach using experimental diagnostics for the optimization of laser process parameters prior to printing. A training dataset is generated by collecting high speed photodiode signal data while printing simple parts containing key geometry features with various process parameter strategies. Supervised learning approaches are employed to train both a forward model and an inverse model. The forward model takes as inputs track-wise geometry features and laser parameters and outputs the photodiode signal along the scan path. The inverse model takes as inputs the geometry features and photodiode signal and predicts the laser parameters. Given the part geometry and a desired photodiode signal, the inverse model can thus determine the required laser parameters. Two test parts which contain defect-prone features are used to assess the validity of the inverse model. The use of the model leads to improved part quality (higher dimensional accuracy, reduced dross, reduced distortion) for both test geometries.
Laser powder bed fusion (LPBF) is a method of additive manufacturing (AM) that selectively melts and fuses together microscopic metallic powder. LPBF offers the benefit of producing custom structures out of high strength metals that can be difficult to fabricate with conventional methods. The challenge of LPBF is that 3D printed structures often have internal pores due to process flaws. Pulsed thermal tomography (PTT) is a method for reconstructing the depth profile of materials, allowing the visualization internal voids in solids. In prior work, we developed a convolutional neural network (CNN) which, having been trained on simulated 2D PTT images of subsurface elliptical defects, was able to classify the semi-major radii, semi-minor radii, and angular orientation of the best-fit ellipses in previously unseen PTT images. The unseen PTT images contained subsurface irregular defect shapes imported from scanning electron microscopy (SEM) images of metallic LPBF-printed specimens. Training the CNN on irregular defect shapes instead of on elliptical shapes would make the resulting classifications more descriptive of actual defect shapes. However, this requires a much higher volume of SEM images of material defects, which are difficult to obtain because of random occurrence of defects in LPBF. To address this challenge, we developed a generative adversarial network (GAN) to augment the existing dataset of SEM defect images. The GAN model is demonstrated to create novel yet realistic defect shapes that can be used as input for simulated PTT images to train CNN.
Polymer Laser Sintering (LS) is an additive manufacturing technique that builds 3D models layer by layer using a laser to selectively melt cross sections in powdered polymeric materials, following sequential slices of the CAD model. LS generally uses thermoplastic polymeric powders, such as polyamides (i.e. Nylon), and the resultant 3D objects are often weaker in their strength compared to traditionally processed materials, due to the lack of polymer inter-chain connection in the z-direction. The objective of this project is to investigate the possibility of printing a melt-processable RTM370 imide resin powder terminated with reactive phenylethynyl groups by LS, followed by a postcure in order to promote additional crosslinking to achieve higher temperature (250-300 C) capability. A preliminary study to build tensile specimens by LS and the corresponding DSC and rheology study of RTM370 during LS process is presented.