SEARCH · Engineering Papers

Results for “integrated controls”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS2010

Control Design for a Generic Commercial Aircraft Engine

This paper describes the control algorithms and control design process for a generic commercial aircraft engine simulation of a 40,000 lb thrust class, two spool, high bypass ratio turbofan engine. The aircraft engine is a complex nonlinear system designed to operate over an extreme range of environmental conditions, at temperatures from approximately -60 to 120+ F, and at altitudes from below sea level to 40,000 ft, posing multiple control design constraints. The objective of this paper is to provide the reader an overview of the control design process, design considerations, and justifications as to why the particular architecture and limits have been chosen. The controller architecture contains a gain-scheduled Proportional Integral controller along with logic to protect the aircraft engine from exceeding any limits. Simulation results illustrate that the closed loop system meets the Federal Aviation Administration s thrust response requirements

Csank, Jeffrey↗

NASA NTRS1984

Highly integrated digital engine control system on an F-15 airplane

The highly integrated digital electronic control (HIDEC) program will demonstrate and evaluate the improvements in performance and mission effectiveness that result from integrated engine-airframe control systems. This system is being used on the F-15 airplane at the Dryden Flight Research Facility of NASA Ames Research Center. An integrated flightpath management mode and an integrated adaptive engine stall margin mode are being implemented into the system. The adaptive stall margin mode is a highly integrated mode in which the airplane flight conditions, the resulting inlet distortion, and the engine stall margin are continuously computed; the excess stall margin is used to uptrim the engine for more thrust. The integrated flightpath management mode optimizes the flightpath and throttle setting to reach a desired flight condition. The increase in thrust and the improvement in airplane performance is discussed in this paper.

Burcham, F. W., Jr.↗

NASA NTRS1993

Bode Integrals And Feedback Control Systems

Feedback maximized in desired frequency ranges. Four of Bode integrals constitute basis of method of optimizing design of feedback control system. Integrals express frequency-domain relationships among, and constraints upon, various measures of attenuation and phase in feedback amplifiers. Applicable to similar magnitudes and phases in feedback control systems. Also used to design feedback compensators to maintain stability and performance in presence of disturbances, noise, and uncertainties in characteristics of plant to be controlled.

Kissel, Glen J.↗

NASA NTRS1977

Design and evaluation of an integrated flight-control system concept for manual IFR VTOL operations

An integrated flight controller, display, and power management system design, suitable for all-weather VTOL flight operations onto small ships, is described. The flight controller uncouples the aircraft's translational and attitude motions, which are then commanded by the pilot, through separate controls. A head-up display provides situation and flight director information sufficient to permit zero-zero landings. The system was applied to a VTOL transport model and simulated on moving base simulators at Ames Research Center. Presented herein are results concerning the aircraft's general handling qualities and, in particular, its handling qualities during IFR landings onto a moving ship.

Merrick, V. K.↗

NASA NTRS1990

Integrated Flight-propulsion Control Concepts for Supersonic Transport Airplanes

Integration of propulsion and flight control systems will provide significant performance improvements for supersonic transport airplanes. Increased engine thrust and reduced fuel consumption can be obtained by controlling engine stall margin as a function of flight and engine operating conditions. Improved inlet pressure recovery and decreased inlet drag can result from inlet control system integration. Using propulsion system forces and moments to augment the flight control system and airplane stability can reduce the flight control surface and tail size, weight, and drag. Special control modes may also be desirable for minimizing community noise and for emergency procedures. The overall impact of integrated controls on the takeoff gross weight for a generic high speed civil transport is presented.

Burcham, Frank W., Jr.↗

NASA NTRS1984

An intelligent robotics control scheme

The problem of robot control is viewed at the level of communicating high-level commands produced by intelligent algorithms to the actuator/sensor controllers. Four topics are considered in the design of an integrated control and communications scheme for an intelligent robotic system: the use of abstraction spaces, hierarchical versus heterarchical control, distributed processing, and the interleaving of the steps of plan creation and plan execution. A scheme is presented for an n-level distributed hierarchical/heterarchical control system that effectively interleaves intelligent planning, execution, and sensory feedback. A three-level version of this scheme has been successfully implemented in the Intelligent Systems Research Lab at NASA Langley Research Center. This implementation forms the control structure for DAISIE (Distributed Artificially Intelligent System for Interacting with the Environment), a testbed system integrating AI software with robotics hardware.

Orlando, N. E.↗

NASA NTRS1975

Propulsion systems technology

The selection of components, control design, simulation, and tests are examined for designing supersonic propulsion systems. Inlet-engine combination under electronic control are shown. Design and test results from the integrated control for afterburning turbofan and supersonic cruise inlet are presented.

Hiller, K. W.↗

NASA NTRS1982

Role of IAC in large space systems thermal analysis

Computer analysis programs to evaluate critical coupling effects that can significantly influence spacecraft system performance are described. These coupling effects arise from the varied parameters of the spacecraft systems, environments, and forcing functions associated with disciplines such as thermal, structures, and controls. Adverse effects can be expected to significantly impact system design aspects such as structural integrity, controllability, and mission performance. One such needed design analysis capability is a software system that can integrate individual discipline computer codes into a highly user-oriented/interactive-graphics-based analysis capability. The integrated analysis capability (IAC) system can be viewed as: a core framework system which serves as an integrating base whereby users can readily add desired analysis modules and as a self-contained interdisciplinary system analysis capability having a specific set of fully integrated multidisciplinary analysis programs that deal with the coupling of thermal, structures, controls, antenna radiation performance, and instrument optical performance disciplines.

Jones, G. K.↗

NASA NTRS1988

Precise computer controlled positioning of robot end effectors using sensory feedback

A preliminary study of the combined position/force control using sensory feedback for a one-dimensional manipulator model, which may count for the spacecraft docking problem or to be extended to the multijoint robot manipulator problem, has been performed. The additional degrees of freedom introduced by the compliant force sensor is included in the system dynamics in the design of precise position control. State feedback based on pole placement method and with integral control is used to design the position controller. A simple constant gain force controller is used as an example to illustrate the dependence of the stability and steady-state accuracy of the overall position/force control on the design of the inner position controller. Supportive simulation results are also provided.

Wang, J. C.↗

NASA NTRS1984

Interactive aircraft flight control and aeroelastic stabilization

An analytical model has been used to study the problem of integrated control system/structural dynamic design. This model utilizes the traditional typical section lifting surface with a control surface attached in 2-D unsteady incompressible flow. The studies have as their purpose the examination of the use of the location of the elastic axis of the airfoil as a design variable in the search for an actively controlled configuration that has a specified flutter margin. Items of interest include the determination of flutter speed and divergence speed as functions of a nondimensional parameter, a sub c, that measures the location (in semi-chords) of the elastic axis with respect to the airfoil midchord. All other parameters are fixed. The behavior of velocity root locus curves with changes in a sub c is illustrated. Also shown is an example of the use of sensitivity derivatives to reposition poles of the open loop system. The behavior of the actively controlled or closed loop system is also discussed. A set of examples are presented to indicate how the shear center parameter, a sub c, affects the design of the controlled system.

Weisshaar, T. A.↗

NASA NTRS1986

Design verification and fabrication of active control systems for the DAST ARW-2 high aspect ratio wing, part 1

A study was conducted under Drones for Aerodynamic and Structural Testing (DAST) program to accomplish the final design and hardware fabrication for four active control systems compatible with and ready for installation in the NASA Aeroelastic Research Wing No. 2 (ARW-2) and Firebee II drone flight test vehicle. The wing structure was designed so that Active Control Systems (ACS) are required in the normal flight envelope by integrating control system design with aerodynamics and structure technologies. The DAST ARW-2 configuration uses flutter suppression, relaxed static stability, and gust and maneuver load alleviation ACS systems, and an automatic flight control system. Performance goals and criteria were applied to individual systems and the systems collectively to assure that vehicle stability margins, flutter margins, flying qualities and load reductions are achieved.

Mcgehee, C. R.↗

NASA NTRS1986

Design verification and fabrication of active control systems for the DAST ARW-2 high aspect ratio wing. Part 2: Appendices

This is Part 2-Appendices of a study conducted under Drones for Aerodynamic and Structural Testing (DAST) Program to accomplish the final design and hardware fabrication for four active control systems compatible with and ready for installation in the NASA Aeroelastic Research Wing No. 2 (ARW-2) and Firebee II drone flight test vehicle. The wing structure was designed so that Active Control Systems (ACS) are required in the normal flight envelope by integrating control system design with aerodynamics and structure technologies. The DAST ARW-2 configuration uses flutter suppression, relaxed static stability, and gust and maneuver load alleviation ACS systems, and an automatic flight control system. Performance goals and criteria were applied to individual systems and the systems collectively to assure that vehicle stability margins, flutter margins, flying qualities, and load reductions were achieved.

Mcgehee, C. R.↗

NASA NTRS1988

Precise computer controlled positioning of robot end effectors using force sensors

A thorough study of combined position/force control using sensory feedback for a one-dimensional manipulator model, which may count for the spacecraft docking problem or be extended to the multi-joint robot manipulator problem, was performed. The additional degree of freedom introduced by the compliant force sensor is included in the system dynamics in the design of precise position control. State feedback based on the pole placement method and with integral control is used to design the position controller. A simple constant gain force controller is used as an example to illustrate the dependence of the stability and steady-state accuracy of the overall position/force control upon the design of the inner position controller. Supportive simulation results are also provided.

Shieh, L. S.↗

NASA NTRS2013

Shock Position Control for Mode Transition in a Turbine Based Combined Cycle Engine Inlet Model

A dual flow-path inlet for a turbine based combined cycle (TBCC) propulsion system is to be tested in order to evaluate methodologies for performing a controlled inlet mode transition. Prior to experimental testing, simulation models are used to test, debug, and validate potential control algorithms which are designed to maintain shock position during inlet disturbances. One simulation package being used for testing is the High Mach Transient Engine Cycle Code simulation, known as HiTECC. This paper discusses the development of a mode transition schedule for the HiTECC simulation that is analogous to the development of inlet performance maps. Inlet performance maps, derived through experimental means, describe the performance and operability of the inlet as the splitter closes, switching power production from the turbine engine to the Dual Mode Scram Jet. With knowledge of the operability and performance tradeoffs, a closed loop system can be designed to optimize the performance of the inlet. This paper demonstrates the design of the closed loop control system and benefit with the implementation of a Proportional-Integral controller, an H-Infinity based controller, and a disturbance observer based controller; all of which avoid inlet unstart during a mode transition with a simulated disturbance that would lead to inlet unstart without closed loop control.

Csank, Jeffrey T.↗

NASA NTRS2001

Integrated Modeling for the Next Generation Space Telescope "Yardstick" Concept

The so-called NASA "Yardstick" design concept for the Next Generation Space Telescope presents unique challenges for systems-level analysis. Simulations that integrate controls, optics, thermal, and structural models are required to evaluate baseline performance, study design sensitivities, and perform design optimization. An integrated modeling approach was chosen using a combination of commercial off-the-shelf and "in-house" developed codes. The resulting capability provides a foundation for linear and non-linear analysis, using both the time and frequency-domain methods. It readily allows various combinations of design parameters and environmental loads to be evaluated directly in terms of key science-related metrics, in this case the scalar RMS (root mean square) line-of-sight and RMS wavefront errors. This presentation first addresses the development of the component, or discipline, models for the Yardstick design. It will then proceed to present the integration of the component models, using linear-systems approaches, in order to support two of the most critical baseline performance analyses: jitter and thermal-elastic stability of the optical telescope assembly (OTA). The results of the jitter analysis indicate that disturbances from the reaction wheels coupled with the lightly-damped and highly-flexible structure present significant challenges to the baseline line-of-sight control architecture. Vibration isolation will be required to meet jitter error requirements. The results of the thermal-elastic analysis indicate that the mirror segment displacements due to ground-to-orbit cool-down of the telescope are within the expected capture range of the segment rigid-body control actuators. This means we will be able to align and phase the primary mirror. However, the results for the analysis of the thermal transient response following an attitude maneuver (slew) show that this telescope design is not sufficiently stable, passively, to meet the wavefront error requirements. Structural re-design is one possibility; alternatively, active thermal control of the OTA may be considered. The Yardstick integrated models were successfully used to demonstrate the feasibility of two thermal control strategies.

Mosier, Gary E.↗

NASA NTRS1989

Qualitative simulation for process modeling and control

A qualitative model is developed for a first-order system with a proportional-integral controller without precise knowledge of the process or controller parameters. Simulation of the qualitative model yields all of the solutions to the system equations. In developing the qualitative model, a necessary condition for the occurrence of oscillatory behavior is identified. Initializations that cannot exhibit oscillatory behavior produce a finite set of behaviors. When the phase-space behavior of the oscillatory behavior is properly constrained, these initializations produce an infinite but comprehensible set of asymptotically stable behaviors. While the predictions include all possible behaviors of the real system, a class of spurious behaviors has been identified. When limited numerical information is included in the model, the number of predictions is significantly reduced.

Dalle Molle, D. T.↗

NASA NTRS1996

Biomechanically Induced and Controller Coupled Oscillations Experienced on the F-16XL Aircraft During Rolling Maneuvers

During rapid rolling maneuvers, the F-16 XL aircraft exhibits a 2.5 Hz lightly damped roll oscillation, perceived and described as 'roll ratcheting.' This phenomenon is common with fly-by-wire control systems, particularly when primary control is derived through a pedestal-mounted side-arm controller. Analytical studies have been conducted to model the nature of the integrated control characteristics. The analytical results complement the flight observations. A three-degree-of-freedom linearized set of aerodynamic matrices was assembled to simulate the aircraft plant. The lateral-directional control system was modeled as a linear system. A combination of two second-order transfer functions was derived to couple the lateral acceleration feed through effect of the operator's arm and controller to the roll stick force input. From the combined systems, open-loop frequency responses and a time history were derived, describing and predicting an analogous in-flight situation. This report describes the primary control, aircraft angular rate, and position time responses of the F-16 XL-2 aircraft during subsonic and high-dynamic-pressure rolling maneuvers. The analytical description of the pilot's arm and controller can be applied to other aircraft or simulations to assess roll ratcheting susceptibility.

Smith, John W.↗

NASA NTRS2022

Robust Controller Synthesis for Vision-based Spacecraft Guidance and Control

This work develops a method for Robust Controller for Vision-based Spacecraft (RCVS) guidance and control, integral to the robust autonomy framework for multi-spacecraft for- mation control and reconfiguration applications. The method is built around the use of a photo-realistic simulator, where a camera is deployed on a tracking spacecraft (ego) in order to observe an uncontrolled spacecraft (target) in a Low Earth Orbit (LEO). In this direction, the proposed approach performs the relative state (attitude and position) estimation of the target spacecraft using Convolutional Neural Network (CNN). The state estimation error is then modeled and the corresponding error-bounds are obtained around a nominal trajectory of the ego and target spacecraft. Next, this work proposes a linear matrix inequalities (LMIs) based approach to controller synthesis, guaranteed to be robust against both model uncertainties and measurement errors, resulting from vision-based estimation. This controller is comprised of two distinct components, one synthesized based on the nominal trajectory, while the “robust” component corrects for deviations from the nominal trajectory. Finally, a tracking scenario that directly utilize the image data for spacecraft guidance and control, is presented to showcase the performance of the proposed robust autonomy framework.

Rahmani, Amir↗