Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “gamma”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Behavior of the Fused Quartz Suspended Core Acoustic Waveguide Sensor in Gamma Radiation

Previously, a fused-quartz acoustic waveguide named the suspended core waveguide with tight-field confinement in a small diameter was developed and its sensing potential in harsh environment was demonstrated with the fabricated periodic acoustic fiber Bragg grating. In this paper, the acoustic sensor was exposed to around 70 Gy/h gamma radiation at room temperature for 3550 h at Oak Ridge National Laboratory. For comparisons, a thermocouple and two optical fiber Bragg gratings were tested under the same conditions. The central frequency reading of the acoustic sensor was found to encounter a relatively fast decrease of 0.5 kHz in the first 800 hours. The reading then became stable, centering at 478.5 kHz with a fluctuation of ±0.2 kHz, and responded to small environmental temperature variations less than 1.2 °C. The major effect to the fluctuation was concluded to be radiation-induced material compaction and expansion. For optical fiber Bragg gratings, the same one-directional fast change of readings in the first 500 hours were observed as well. Although the optical gratings were able to track temperature changes, they also showed continuous drifts. The survivability and consistency of the acoustic sensor under long-term gamma radiation could lead to new sensing methods in nuclear applications.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2022

Optimization Simulations for a Gamma-Ray Calibration Standard for a Cyclic Neutron Activation Analysis Pneumatic System at the Penn State Breazeale Reactor

For new experimental setups, the initial testing and calibrations can be expensive and time consuming without prior optimization. However, these issues can be mitigated using realistic modeling and simulation studies of the proposed system a priori. Specifically, an experiment can be performed virtually using realistic simulations and the expected results evaluated to inform adjustments of the experimental setup to achieve optimum results. At the Penn State Breazeale Reactor, a new pneumatic transfer system has been developed for the detection and characterization of short-lived fission fragments to enhance and complement existing nuclear data. The system accomplishes this task by transporting samples cyclically between an assortment of gamma-ray/neutron detectors and the reactor-core vicinity with sub-second transit times. The measured neutron flux paired with simulations of detector response using Geant4 and a custom module for estimating cascade summing effects and corrections were used to select sample-material masses for system characterization. With the optimized sample masses, an experimental counting plan for characterizing the repeatability of the newly developed pneumatic system was developed. Finally, the predictions made with these simulations allowed for optimization of the irradiation sample characteristics and gamma-ray detection system.

cyclic neutron activation, gamma-ray spectroscopy↗
DOE OSTI2021

Improved Gamma-Ray Point Source Quantification in Three Dimensions by Modeling Attenuation in the Scene

We discuss using a series of detector measurements taken at different locations to localize a source of radiation as a well-studied problem. The source of radiation is sometimes constrained to a single point-like source, in which case the location of the point source can be found using techniques such as maximum likelihood. Recent advancements have shown the ability to locate point sources in 2D and even 3D, but few have studied the effect of intervening material on the problem. In this work we examine gamma-ray data taken from a freely moving system and develop voxelized 3-D models of the scene using data from the onboard LiDAR. Ray casting is used to compute the distance each gamma ray travels through the scene material, which is then used to calculate attenuation assuming a single attenuation coefficient for solids within the geometry. Parameter estimation using maximum likelihood is performed to simultaneously find the attenuation coefficient, source activity, and source position that best match the data. Using a simulation, we validate the ability of this method to reconstruct the true location and activity of a source, along with the true attenuation coefficient of the structure it is inside, and then we apply the method to measured data with sources and find good agreement.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2022

Gamma-radiation-induced negative nonlinear absorption in quartz glass

The effect of ionizing radiation on the nonlinear optical properties of materials needs to be considered for applications that employ high-power laser pulses in extreme radiation environments. The Heraeus Infrasil302 optical quartz glass was irradiated by gamma rays, and its nonlinear absorption was measured using the open-aperture Z-scan technique with nanosecond laser pulses. Irradiation results in a negative nonlinear absorption coefficient whose magnitude increases with irradiation dose. Nonlinear absorption coefficients of -0.78, -1.14, -1.29, and -1.88~ × ~10 -13 m/W are measured for gamma doses of 600 krad, 1.2 Mrad, 3.6 Mrad, and 10 Mrad, respectively. Thermal annealing restores the optical properties of quartz-glass to their unirradiated values. It is suggested that metallic impurities introduced by the manufacturing process have a role in inducing saturated absorption in irradiated quartz glass, which manifests as negative nonlinear absorption coefficient, and is demonstrated by comparing Infrasil302 quartz results to equivalent irradiated measurements for Spectrosil2000 quartz.

07 ISOTOPE AND RADIATION SOURCES↗
DOE OSTI2021

Dense Pair and Gamma-Ray Creation Using Ultra-Intense Lasers (Final Technical Report)

Lasers with intensity >1.4x10 18 W.cm -2 irradiating solid targets couple 10-50% of its energy to “hot electrons” near the critical surface, with temperature kT > mc 2 . When these hot electrons impact high-Z target ions (e.g. Au, Pt), they emit copious bremsstrahlung gamma-rays and create e + e - pairs via the Trident process. For targets thicker than ~0.1mm, the gamma-rays create secondary pairs via the Bethe-Heitler processes. The concept of using lasers to create pairs was first studied by Shearer et al (1973). Motivated by the rapid advance of short-pulse ultra-intense lasers based on chirped-pulse amplification, Liang (1994) first proposed irradiating solid Au targets with laser intensity ≥10 20 W.cm -2 to create dense e + e - pairs. Using particle-in-cell (PIC, Birdsall and Langdon, 1991) simulations, Liang et al (1998, 2002) estimated that high-energy PW lasers can in principle achieve ultra-high in-situ pair densities. Subsequent studies supported this idea and found that for gold foils thicker than ~50 μm, the pair yield is dominated by the Bethe-Heitler (BH, Heitler 1954) process. Cowan et al (1999, 2000) using the LLNL Nova PW-laser to irradiate 125μm gold foils first observed pair creation, followed by Chen et al (2009) who demonstrated copious BH pair creation using the Titan, Omega-EP and Orion lasers. However, the emerging e + /e - ratio of these experiments was ≤ few %, and the pair density was only 10 13 /cc so that the pair jet transverse size R(~mm) was < pair skin depth c/ω + (=8πn+e 2 /m) 1/2 ). This was insufficient to qualify as a bona fide ”pair plasma”.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2022

Revised 207 Pb Thermal Capture Gamma-ray Spectrum Evaluation

This report details the revision of the JENDL-4.0 thermal capture gamma-ray spectrum evaluation for 207 Pb and the comparison of the current evaluations and the revised spectrum. The history of the available reaction evaluations is described and the deficiencies are identified. The modified spectrum has an average energy of 7.329 MeV and an average multiplicity of 1.005, leading to a total energy released value of 7.366 MeV, just 0.03% off from the Q-value of the reaction, 7.368 MeV. Based on comparison to the measurements and structure libraries considered, the revised evaluation is closer to reality and should provide more accurate coupled neutron-gamma ray calculations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2023

Gamma-Ray Transient Network Science Analysis Group Report

The Interplanetary Network (IPN) is a detection, localization and alert system that utilizes the arrival time of transient signals in gamma-ray detectors on spacecraft separated by planetary baselines to geometrically locate the origin of these transients. Due to the changing astrophysical landscape and the new emphasis on time domain and multi messenger astrophysics (TDAMM) from the Pathways to Discovery in Astronomy and Astrophysics for the 2020s , this Gamma-ray Transient Network Science Analysis Group was tasked to understand the role of the IPN and high-energy monitors in this new era. The charge includes describing the science made possible with these facilities, tracing the corresponding requirements and capabilities, and highlighting where improved operations of existing instruments and the IPN would enhance TDAMM science. While this study considers the full multiwavelength and multimessenger context, the findings are specific to space-based high-energy monitors. These facilities are important both for full characterization of these transients as well as facilitating follow-up observations through discovery and localization. The full document reports the history of this field in Section 1, followed by our detailed analyses and findings in some 68 pages, providing a holistic overview of the role of the IPN and high-energy monitors in the coming decades.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

On the Mechanism of the Steady-State Gamma Radiolysis-Induced Scissions of the Phenyl-Vinyl Polyester-Based Resins

The major societal problem of polymeric waste necessitates new approaches to break down especially challenging discarded waste streams. Gamma radiation was utilized in conjunction with varying solvent environments in an attempt to discern the efficacy of radiolysis as a tool for the deliberate degradation of model network polyesters. Our EPR results demonstrated that gamma radiolysis of neat resin and in the presence of four widely used solvents induces glycosidic scissions on the backbone of the polyester chains. EPR results clearly show the formation of alkoxy radicals and C-centered radicals as primary intermediate radiolytic products. Despite the protective role of the phenyl groups on the backbone of the radiation-induced polyester chains, the radiolytic-glycosidic scissions predominate. Among the following three solvents used in this study (water, isopropyl alcohol, and dichloromethane), the highest radiolytic yield of glycosidic scission was achieved using water. The •OH radicals produced in the radiolysis of phenyl unsaturated polyester aqueous suspensions very rapidly abstract H atoms from the methylene group, which is followed by a very rapid glycosidic scission. The lowest glycosidic yield was found in the dichloromethane solutions of these polyester resins due to scavenging by the fast electron capture reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Contrastive Machine Learning with Gamma Spectroscopy Data Augmentations for Detecting Shielded Radiological Material Transfers

Data analysis techniques can be powerful tools for rapidly analyzing data and extracting information that can be used in a latent space for categorizing observations between classes of data. Machine learning models that exploit learned data relationships can address a variety of nuclear nonproliferation challenges like the detection and tracking of shielded radiological material transfers. The high resource cost of manually labeling radiation spectra is a hindrance to the rapid analysis of data collected from persistent monitoring and to the adoption of supervised machine learning methods that require large volumes of curated training data. Instead, contrastive self-supervised learning on unlabeled spectra can enhance models that are built on limited labeled radiation datasets. This work demonstrates that contrastive machine learning is an effective technique for leveraging unlabeled data in detecting and characterizing nuclear material transfers demonstrated on radiation measurements collected at an Oak Ridge National Laboratory testbed, where sodium iodide detectors measure gamma radiation emitted by material transfers between the High Flux Isotope Reactor and the Radiochemical Engineering Development Center. Label-invariant data augmentations tailored for gamma radiation detection physics are used on unlabeled spectra to contrastively train an encoder, learning a complex, embedded state space with self-supervision. A linear classifier is then trained on a limited set of labeled data to distinguish transfer spectra between byproducts and tracked nuclear material using representations from the contrastively trained encoder. The optimized hyperparameter model achieves a balanced accuracy score of 80.30%. Any given model—that is, a trained encoder and classifier—shows preferential treatment for specific subclasses of transfer types. Regardless of the classifier complexity, a supervised classifier using contrastively trained representations achieves higher accuracy than using spectra when trained and tested on limited labeled data.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Feasibility of Observing Gamma-Ray Polarization from Cygnus X-1 Using a CubeSat

Instruments flown on CubeSats are small. Meaningful applications of CubeSats in astronomical observations rely on the choice of a particular subject that is feasible for CubeSats. Here we report the result of a feasibility study for observing gamma-ray polarization from Cygnus X-1 using a small Compton polarimeter on board a 3U CubeSat. Silicon detectors and cerium bromide scintillators were employed in the instrument models that we discuss in this study. Through Monte Carlo simulations with a Geant4-based MEGAlib package, we found that, with a 10 Ms on-axis, zenith-direction observation in a low-inclination, low-altitude, Earth-orbit radiation background environment, the minimum detectable polarization degree can be down to about 10% in 160–250 keV, 20% in 250–400 keV, and 65% in 400–2000 keV. A 3U CubeSat dedicated to observing Cygnus X-1 can therefore yield useful information on the polarization state of gamma-ray emissions from the brightest persistent X-ray black hole binary in the sky.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2022

Searches for Neutrinos from Gamma-Ray Bursts Using the IceCube Neutrino Observatory

Gamma-ray bursts (GRBs) are considered as promising sources of ultra-high-energy cosmic rays (UHECRs) due to their large power output. Observing a neutrino flux from GRBs would offer evidence that GRBs are hadronic accelerators of UHECRs. Previous IceCube analyses, which primarily focused on neutrinos arriving in temporal coincidence with the prompt gamma-rays, found no significant neutrino excess. The four analyses presented in this paper extend the region of interest to 14 days before and after the prompt phase, including generic extended time windows and targeted precursor searches. GRBs were selected between 2011 May and 2018 October to align with the data set of candidate muon-neutrino events observed by IceCube. No evidence of correlation between neutrino events and GRBs was found in these analyses. Limits are set to constrain the contribution of the cosmic GRB population to the diffuse astrophysical neutrino flux observed by IceCube. Prompt neutrino emission from GRBs is limited to ≲1% of the observed diffuse neutrino flux, and emission on timescales up to 10 4 s is constrained to 24% of the total diffuse flux.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2023

On the Anticorrelation between Duration and Redshift in Gamma-Ray Bursts

Abstract For gamma-ray bursts (GRBs) with durations greater than two seconds (so-called long GRBs), the intrinsic prompt gamma-ray emission appears, on average, to last longer for bursts at lower redshifts. We explore the nature of this duration–redshift anticorrelation, describing systems and conditions in which this cosmological evolution could arise. In particular, we explore its dependence on the metallicity of a massive star progenitor, because we can securely count on the average stellar metallicity to increase with decreasing redshift. Although stars with higher metallicity/lower redshift lose mass and angular momentum through line-driven winds, in some cases these stars are able to form more extended accretion disks when they collapse, potentially leading to longer-duration GRBs. We also examine how this duration–redshift trend may show up in interacting binary models composed of a massive star and compact object companion, recently suggested to be the progenitors of radio-bright GRBs. Under certain conditions, mass loss and equation-of-state effects from massive stars with higher metallicity and lower redshift can decrease the binary separation. This can then lead to spin-up of the massive star and allow for a longer-duration GRB upon the massive star’s collapse. Finally, the duration–redshift trend may also be supported by a relatively larger population of small-separation binaries born in situ at low redshift.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2021

On the Existence of the Plateau Emission in High-energy Gamma-Ray Burst Light Curves Observed by Fermi-LAT

The Large Area Telescope (LAT) on board the Fermi Gamma-ray Space Telescope (Fermi) shows long-lasting high-energy emission in many gamma-ray bursts (GRBs), similar to X-ray afterglows observed by the Neil Gehrels Swift Observatory (Swift). Some LAT light curves (LCs) show a late-time flattening reminiscent of X-ray plateaus. We explore the presence of plateaus in LAT temporally extended emission analyzing GRBs from the second Fermi-LAT GRB Catalog from 2008 to 2016 May with known redshifts, and check whether they follow closure relations corresponding to four distinct astrophysical environments predicted by the external forward shock model. We find that three LCs can be fit by the same phenomenological model used to fit X-ray plateaus and show tentative evidence for the existence of plateaus in their high-energy extended emission. The most favorable scenario is a slow-cooling regime, whereas the preferred density profile for each GRBs varies from a constant-density interstellar medium to an r –2 wind environment. We also compare the end time of the plateaus in γ-rays and X-rays using a statistical comparison with 222 Swift GRBs with plateaus and known redshifts from 2005 January to 2019 August. Within this comparison, the case of GRB 090510 shows an indication of chromaticity at the end time of the plateau. Finally, we update the 3D fundamental plane relation among the rest-frame end time of the plateau, its correspondent luminosity, and the peak prompt luminosity for 222 GRBs observed by Swift. We find that these three LAT GRBs follow this relation.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2024

The Dependence of Gamma-Ray Burst Jet Collimation on Black Hole Spin

Gamma-ray bursts (GRBs) are the most luminous events in the Universe and are excellent laboratories to study extreme physical phenomena in the cosmos. Despite a long trajectory of progress in understanding these highly energetic events, there are still many observed features that are yet to be fully explained. Observations of the jet opening angle of long gamma-ray bursts (LGRBs) suggest that LGRB jets are narrower for those GRBs at higher redshift. This phenomenon has been explained in the context of collimation by the stellar envelope, with denser (lower metallicity) stars at higher redshifts able to collimate the jet more effectively. However, until now, the dependence of the jet opening angle on the properties of the central engine has not been explored. We investigate the effect of black hole spin on the jet collimation angle for a magnetically launched jet, using the general relativistic radiation magnetohydrodynamical code ν bhlight . We present 3D results for a range of spin values. The simulations show that higher-spinning black holes tend to create narrower jets. If indeed LGRB progenitors in the early Universe are able to produce black hole central engines with higher spin, this could account for at least some of the observed jet opening angle-redshift correlation.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2020

ISOCS-based Extended In Situ Gamma Spectrometry Services Tool SuperISOCS for Waste Measurements - 20275

Canberra's In Situ Object Counting System (ISOCS) is an established tool used for gamma spectrometry. It allows physical representation of complex geometries and mathematical calculation of the calibration function while avoiding the need for radioisotope standards. ISOCS provides a large range of templates to generate the geometry for most nuclear waste components in nuclear facilities. Nonetheless, there are some complex geometries where the accuracy attainable is limited by the conventional ISOCS templates. An ISOCS-based extended in-situ Gamma Spectrometry service tool has been developed, based on the so-called SuperISOCS (SISOCS) software. This tool was developed to generate the most complex geometries. The principle of geometry construction is based on the composition of 8 different primitive geometries. The primitive object is able to be cut and to change a part of an object. An object is able to overlap to another one to form a more complex object. These functions refine the modelled geometry compared to the real objects and decrease the measurement systematic error because they allow the mathematical model to represent the real-life geometry more faithfully through reducing the approximations and simplifications that need to be made The algorithm of SISOCS is the same as that of standard ISOCS. A set of calculations was done in comparison with MCNP efficiency calculation and SISOCS results. 80 different models were compared between SISOCS and MCNP, with added 30 cases compared between ISOCS and SISOCS. The average differences were less than 2%, for all energy's efficiency calculations. In this paper we illustrate the benefits that this new tool can provide, in terms of improved accuracy for complex realistic geometries, through simulation of some example scenarios. Furthermore, we demonstrate, through SISOCS modelling of the real object data test, the comparison between SISOCS to ISOCS calculations for the same geometry. This paper describes the added functions that are easily employed using SISOCS. Our results show the potential application and benefit of this technique for real waste assay projects and the way to integrate the tool into the waste assay systems. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

ATR Gamma Facility User Guide

Advanced Test Reactor Gamma Facility User Guide provides guidance to assist Test Sponsors in meeting the administrative requirements associated with ATR Gamma Facility irradiations. The sections in the guide provide a brief discussion of each step, including purpose, party responsible for execution, typical order of events, general methodology, and location at which each step takes place. The length of time to complete an experiment will vary depending on the complexity of the irradiation test (i.e., experiment design) and irradiation duration.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗