Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “fracture modelling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Inverse Method for Estimation of Composite Kink-Band Toughness from Open-Hole Compression Strength Data

Fiber-reinforced polymer matrix composite materials can fail by kink-band propagation mechanism when subjected to in-plane compressive loading. This mode of failure is especially prevalent in compressive loading of laminates with holes, cut-outs, or impact damage. Most of the successful models for predicting compressive strength of such laminates require “fracture” toughness associated with kink-band propagation under in-plane compression. However, this property is difficult to measure experimentally, limiting the use of such models in design practice. In this paper an inverse method is proposed to estimate the kink-band toughness of the laminate from its open-hole compression strength data, which is an easier property to measure experimentally. Furthermore, a scaling relationship is proposed to estimate kink-band toughness for other laminate configurations of the same material.

Luke Borkowski↗
NASA NTRSDate not supplied

Hot Structure Concepts and Materials for Space Exploration Project

Hot structures are multifunctional material systems that integrate the functions of thermal protection systems (TPS) and primary structure to increase mass efficiency in aerospace vehicles. The goal of this project was to improve our capabilities for developing lightweight, reusable, and reliable hot structures concepts to enable advanced space exploration missions. Specifically, current hot structure carbon/carbon (C/C) composite material systems have low interlaminar strength, which can lead to material failures at low load levels, and large material property variability in as-fabricated parts. Two parallel paths were followed to address these shortcomings. First, analysis models were developed to identify the conditions under which excessive interlaminar stresses occur and to evaluate the potential of stitching the C/C laminae to improve the interlaminar thermal-structural response. This effort included the development of high-fidelity, fracture-based thermal-structural finite element analysis models to evaluate critical features needed to produce efficient hot structure concepts. The second path focused on developing atomistic and mesoscale simulation tools to model the fabrication process in an effort to reduce the time and cost of production while improving the quality of the resulting parts. Aspects of the process currently being investigated include the infusion of the matrix precursor into the fiber preform, the cure of the precursor molecules into their polymeric form, and the carbonization and graphitization of the polymer to form the carbon matrix material. Results of the 6-month study are presented herein.

thermal↗
NASA NTRS2013

Applications of Automation Methods for Nonlinear Fracture Test Analysis

Using automated and standardized computer tools to calculate the pertinent test result values has several advantages such as: 1. allowing high-fidelity solutions to complex nonlinear phenomena that would be impractical to express in written equation form, 2. eliminating errors associated with the interpretation and programing of analysis procedures from the text of test standards, 3. lessening the need for expertise in the areas of solid mechanics, fracture mechanics, numerical methods, and/or finite element modeling, to achieve sound results, 4. and providing one computer tool and/or one set of solutions for all users for a more "standardized" answer. In summary, this approach allows a non-expert with rudimentary training to get the best practical solution based on the latest understanding with minimum difficulty.Other existing ASTM standards that cover complicated phenomena use standard computer programs: 1. ASTM C1340/C1340M-10- Standard Practice for Estimation of Heat Gain or Loss Through Ceilings Under Attics Containing Radiant Barriers by Use of a Computer Program 2. ASTM F 2815 - Standard Practice for Chemical Permeation through Protective Clothing Materials: Testing Data Analysis by Use of a Computer Program 3. ASTM E2807 - Standard Specification for 3D Imaging Data Exchange, Version 1.0 The verification, validation, and round-robin processes required of a computer tool closely parallel the methods that are used to ensure the solution validity for equations included in test standard. The use of automated analysis tools allows the creation and practical implementation of advanced fracture mechanics test standards that capture the physics of a nonlinear fracture mechanics problem without adding undue burden or expense to the user. The presented approach forms a bridge between the equation-based fracture testing standards of today and the next generation of standards solving complex problems through analysis automation.

Allen, Phillip A.↗
NASA NTRS2002

Generalized Reliability Methodology Applied to Brittle Anisotropic Single Crystals

A generalized reliability model was developed for use in the design of structural components made from brittle, homogeneous anisotropic materials such as single crystals. The model is based on the Weibull distribution and incorporates a variable strength distribution and any equivalent stress failure criteria. In addition to the reliability model, an energy based failure criterion for elastically anisotropic materials was formulated. The model is different from typical Weibull-based models in that it accounts for strength anisotropy arising from fracture toughness anisotropy and thereby allows for strength and reliability predictions of brittle, anisotropic single crystals subjected to multiaxial stresses. The model is also applicable to elastically isotropic materials exhibiting strength anisotropy due to an anisotropic distribution of flaws. In order to develop and experimentally verify the model, the uniaxial and biaxial strengths of a single crystal nickel aluminide were measured. The uniaxial strengths of the <100> and <110> crystal directions were measured in three and four-point flexure. The biaxial strength was measured by subjecting <100> plates to a uniform pressure in a test apparatus that was developed and experimentally verified. The biaxial strengths of the single crystal plates were estimated by extending and verifying the displacement solution for a circular, anisotropic plate to the case of a variable radius and thickness. The best correlation between the experimental strength data and the model predictions occurred when an anisotropic stress analysis was combined with the normal stress criterion and the strength parameters associated with the <110> crystal direction.

Salem, Jonathan A.↗
NASA NTRS2015

Modeling of Fragmentation of Asteroids

The objective of this study is to understand fragmentation and fracture of a given asteroid and mechanisms of break-up. The focus of the present work is to develop modeling techniques for stony asteroids in 10m-100m range to answer two questions: 1) What is the role of material makeup of an asteroid in the stress distribution? 2)How is stress distribution altered in the presence of pre-existing defects?

Asteroids↗
NASA NTRS2013

Does Aspartic Acid Racemization Constrain the Depth Limit of the Subsurface Biosphere?

Previous studies of the subsurface biosphere have deduced average cellular doubling times of hundreds to thousands of years based upon geochemical models. We have directly constrained the in situ average cellular protein turnover or doubling times for metabolically active micro-organisms based on cellular amino acid abundances, D/L values of cellular aspartic acid, and the in vivo aspartic acid racemization rate. Application of this method to planktonic microbial communities collected from deep fractures in South Africa yielded maximum cellular amino acid turnover times of approximately 89 years for 1 km depth and 27 C and 1-2 years for 3 km depth and 54 C. The latter turnover times are much shorter than previously estimated cellular turnover times based upon geochemical arguments. The aspartic acid racemization rate at higher temperatures yields cellular protein doubling times that are consistent with the survival times of hyperthermophilic strains and predicts that at temperatures of 85 C, cells must replace proteins every couple of days to maintain enzymatic activity. Such a high maintenance requirement may be the principal limit on the abundance of living micro-organisms in the deep, hot subsurface biosphere, as well as a potential limit on their activity. The measurement of the D/L of aspartic acid in biological samples is a potentially powerful tool for deep, fractured continental and oceanic crustal settings where geochemical models of carbon turnover times are poorly constrained. Experimental observations on the racemization rates of aspartic acid in living thermophiles and hyperthermophiles could test this hypothesis. The development of corrections for cell wall peptides and spores will be required, however, to improve the accuracy of these estimates for environmental samples.

cellular↗
NASA NTRS1989

Nonlinear fracture of concrete and ceramics

The nonlinear fracture process zones in an impacted unnotched concrete bend specimen, a prenotched ceramic bend specimen, and an unnotched ceramic/ceramic composite bend specimen were estimated through hybrid experimental numerical analysis. Aggregate bridging in concrete, particulate bridging in ceramics, and fiber bridging in ceramic/ceramic composite are modeled by Barenblatt-type cohesive zones which are incorporated into the finite-element models of the bend specimens. Both generation and propagation analyses are used to estimate the distribution of crack closure stresses in the nonlinear fracture process zones. The finite-element models are then used to simulate fracture tests consisting of rapid crack propagation in an impacted concrete bend specimen, and stable crack growth and strain softening in a ceramic and ceramic/ceramic composite bend specimens.

Kobayashi, Albert S.↗
NASA NTRS1989

Thermoplastic matrix composites - Finite-element analysis of mode I and mode II failure specimens

A finite-element analysis was conducted to evaluate the stress distributions within mode I and mode II failure specimens, assuming both isotropic and orthotropic elastic material properties. The effects of anisotropy on both the magnitude and the location of the highest stress concentration at the vicinity of the crack tip are significant. The results from modeling realistic blunt crack tip geometry and resin-rich zones imply that local variations in the microstructure strongly influence the stress state near the crack tip and therefore the measured fracture properties. In addition, the features of a viscoelastic model for thermoplastic matrices are described. This model will be used in future investigations of matrix-dominated failure phenomena.

Bankert, Ray J.↗
NASA NTRS1972

Slow and fast motion of cracks in inelastic solids. Part 1: Slow growth of cracks in a rate sensitive tresca solid. Part 2: Dynamic crack represented by the Dugdale model

An extension is proposed of the classical theory of fracture to viscoelastic and elastic-plastic materials in which the plasticity effects are confined to a narrow band encompassing the crack front. It is suggested that the Griffith-Irwin criterion of fracture, which requires that the energy release rate computed for a given boundary value problem equals the critical threshold, ought to be replaced by a differential equation governing the slow growth of a crack prior to the onset of rapid propagation. A new term which enters the equation of motion in the dissipative media is proportional to the energy lost within the end sections of the crack, and thus reflects the extent of inelastic behavior of a solid. A concept of apparent surface energy is introduced to account for the geometry dependent and the rate dependent phenomena which influence toughness of an inelastic solid. Three hypotheses regarding the condition for fracture in the subcritical range of load are compared. These are: (1) constant fracture energy (Cherepanov), (2) constant opening displacement at instability (Morozov) and (3) final stretch criterion (Wnuk).

Wnuk, M. P.↗
NASA NTRS1984

Ultrasonic nondestructive evaluation, microstructure, and mechanical property interrelations

Ultrasonic techniques for mechanical property characterizations are reviewed and conceptual models are advanced for explaining and interpreting the empirically based results. At present, the technology is generally empirically based and is emerging from the research laboratory. Advancement of the technology will require establishment of theoretical foundations for the experimentally observed interrelations among ultrasonic measurements, mechanical properties, and microstructure. Conceptual models are applied to ultrasonic assessment of fracture toughness to illustrate an approach for predicting correlations found among ultrasonic measurements, microstructure, and mechanical properties.

Vary, A.↗
NASA NTRS1985

Planetary Interior Modeling and Tectonic Implications

A technique is described for estimating spectral admittance functions using Pioneer Venus gravity and topography data. These admittance functions provide a convenient means to carry out systematic geophysical studies over much of the surface of Venus with a variety of interior density models. The admittance functions are calculated in the observation space of line-of-sight (LOS) gravity. Both closed and open system petrological models are considered for the Tharsis region of Mars. An analytic theory for isostatic compensation on one-plate planet is applied, including membrane stresses in the lithosphere, self gravitation, and rotational ellipticity. Crucial to this stress modeling and also to the petrological modeling is the observation that the earliest fracturing seen in the Tharsis region is associated with isostatic stresses. The radial fractures that extend far from Tharsis are associated with an additional and/or a completely different mechanism.

Phillips, R. J.↗
NASA NTRS2003

Martian Crustal Magnetism: What Have We Learned After Approximately 6 Years of MGS Observations?

The MAG/ER investigation aboard the Mars Global Surveyor (MGS) has established conclusively that an internal, dynamo-generated field does not currently exist at Mars and discovered, unexpectedly, strong magnetization in the crust. An estimate of the upper limit of the current Mars dipole moment derived from the MGS data yields M < ~2 x 10(exp 17) A-m2, which corresponds to a surface equatorial field strength of < 0.5 nT. The intense magnetization of the crust is closely associated with the ancient, heavily cratered high terrain, which lies south of Mars dichotomy boundary. The correlation of magnetization with the old terrain and the role of impacts, which have modified the magnetic properties of the crust, constitute a new and powerful diagnostic tool that is providing a unique view into the early thermal history of the planet, which was almost totally unknown prior to the arrival of MGS. Data from the Lunar Prospector mission complement contemporary analyses and interpretation of crustal magnetism in planetary system bodies that do not currently possess core dynamos. The observation of magnetic lineations over Terra Sirenum (Sirenum Fossae) and Terra Cimmeria, are suggestive of tectonic processes observed at Earth in association with sea-floor spreading and geomagnetic field reversals. If this association is correct, it would indicate the possible existence of plate tectonics and magnetic field reversals in Mars' early history. Alternative models involving fault/graben formation associated with the fracturing of a thin, magnetized crustal layer by tectonic or volcanism-induced stresses, yield equally valid interpretations. To date, no reliable correlation between topography, geology and crustal magnetism has been established and the origin of these remarkable Martian magnetic anomalies remains a mystery.

M H Acuna↗
NASA NTRS2004

Gardosian Patterns in Tribology

The following paper is a memorial retrospective on selected research of Dr. Michael N. Gardos. Dr. Gardos spent his professional career engaged in tribological research which often extended the scientific boundaries of the field. Several of the concepts he put forth into the tribology community were initially met with grave skepticism but over time his views have been largely embraced but not widely acknowledged. His approach to new research topics was often characterized by these qualities: 1) pioneering points of view, 2) the use of the model experiment, and 3) the presence of multiple research agendas for each single experiment. I have chosen to name his research approach as "Gardosian Patterns" in honor of his contributions to Tribology. Three specific examples of these patterns will be reviewed. One is the concept of atomic level tailoring of materials to control macroscopic properties. A second is the use of a model ball polishing experiment to identify high fracture toughness ceramics for use in rolling element bearings. A third Gardosian Pattern example is his pioneering work with the tribology of diamond and diamond films in which he proposed controlling friction via surface bond tailoring. In these examples, Gardos utilized conventional research tools in unconventional ways and, at times, even developed new tools which have become part of the mainstream. His remarkable career has left a positive and lasting mark on Tribology.

DellaCorte, Christopher↗
NASA NTRS2018

VCCT with Progressive Nodal Release for Simulating Mixed-Mode Delamination: Formulation, Algorithmic Improvements and Implications

To simulate the propagation of cracks using the Virtual Crack Closure Technique (VCCT), intermediate crack positions between existing node pairs can be modeled by progressively releasing the nodes using fracture mechanics principles. This approach has been implemented in commercial software and can be applied to simulate delamination growth. Recent research has provided insight into the synchronized mixed mode nodal release, extending and formalizing the methodology for delamination growth. This paper documents the development of the Jacobians associated with delamination propagation under quasi-static mixed-mode conditions, leading to improvements in convergence of the implicit nonlinear solvers used.

Mabson, G. E.↗
NASA NTRS2018

VCCT with Progressive Nodal Release for Simulating Mixed-Mode Delamination: Formulation, Algorithmic Improvements and Implications

To simulate the propagation of cracks using the Virtual Crack Closure Technique (VCCT), intermediate crack positions between existing node pairs can be modeled by progressively releasing the nodes using fracture mechanics principles. This approach has been implemented in commercial software and can be applied to simulate delamination growth. Recent research has provided insight into the synchronized mixed mode nodal release, extending and formalizing the methodology for delamination growth. This paper documents the development of the Jacobians associated with delamination propagation under quasi-static mixed-mode conditions, leading to improvements in convergence of the implicit nonlinear solvers used.

G E Mabson↗
NASA NTRSDate not supplied

Initiation and Propagation of Skin/Stiffener Separation in Postbuckled Structures Subjected to Cyclic Loads

A methodology is proposed to evaluate experimentally and numerically the initiation and propagation of skin/stiffener separation in postbuckled panels subjected to cyclic loads. The response mechanisms that characterize skin/stiffener separation were investigated using a three point bend (3PB) test specimen, which is a simple specimen consisting of a laminate representing the skin and a doubler representing the stiffener flange. The 3PB tests were performed under quasi-static and cyclic loads. A fatigue cohesive model was used to analyze the initiation and propagation of skin/stiffener separation in the 3PB. The results indicate that the fatigue cohesive model with model parameters obtained from quasi-static fracture tests can provide accurate predictions of initiation from a pristine state, and the rate of fatigue crack propagation for a variety of mode mixities, load levels, and stress ratios.

Carlos G Davila↗