Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “feedback control systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Multivariable control of the Space Shuttle Remote Manipulator System using linearization by state feedback

This paper demonstrates an approach to nonlinear control system design that uses linearization by state feedback to allow faster maneuvering of payloads by the Shuttle Remote Manipulator System (SRMS). A nonlinear feedback law is defined to cancel the nonlinear plant dynamics so that a linear controller can be designed for the SRMS. First a nonlinear design model was generated via SIMULINK. This design model included nonlinear arm dynamics derived from the Lagrangian approach, linearized servo model, and linearized gearbox model. The current SRMS position hold controller was implemented on this system. Next, a trajectory was defined using a rigid body kinematics SRMS tool, KRMS. The maneuver was simulated. Finally, higher bandwidth controllers were developed. Results of the new controllers were compared with the existing SRMS automatic control modes for the Space Station Freedom Mission Build 4 Payload extended on the SRMS.

Gettman, Chang-Ching L.↗
NASA NTRS1999

Real-Time Optical Fuel-to-Air Ratio Sensor for Gas Turbine Combustors

The measurement of the temporal distribution of fuel in gas turbine combustors is important in considering pollution, combustion efficiency and combustor dynamics and acoustics. Much of the previous work in measuring fuel distributions in gas turbine combustors has focused on the spatial aspect of the distribution. The temporal aspect however, has often been overlooked, even though it is just as important. In part, this is due to the challenges of applying real-time diagnostic techniques in a high pressure and high temperature environment. A simple and low-cost instrument that non-intrusively measures the real-time fuel-to-air ratio (FAR) in a gas turbine combustor has been developed. The device uses a dual wavelength laser absorption technique to measure the concentration of most hydrocarbon fuels such as jet fuel, methane, propane, etc. The device can be configured to use fiber optics to measure the local FAR inside a high pressure test rig without the need for windows. Alternatively, the device can readily be used in test rigs that have existing windows without modifications. An initial application of this instrument was to obtain time-resolved measurements of the FAR in the premixer of a lean premixed prevaporized (LPP) combustor at inlet air pressures and temperatures as high as 17 atm at 800 K, with liquid JP-8 as the fuel. Results will be presented that quantitatively show the transient nature of the local FAR inside a LPP gas turbine combustor at actual operating conditions. The high speed (kHz) time resolution of this device, combined with a rugged fiber optic delivery system, should enable the realization of a flight capable active-feedback and control system for the abatement of noise and pollutant emissions in the future. Other applications that require an in-situ and time-resolved measurement of fuel vapor concentrations should also find this device to be of use.

Nguyen, Quang-Viet↗
NASA NTRS2000

Controlling Microbial Byproducts using Model-Based Substrate Monitoring and Control Strategies

We have developed a computer-controlled bioreactor system to study various aspects of microbially-mediated nitrogen cycling. The system has been used to investigate methods for controlling microbial denitrification (the dissimilatory reduction of nitrate to N2O and N2) in hydroponic plant growth chambers. Such chambers are key elements of advanced life support systems being designed for use on long duration space missions, but nitrogen use efficiency in them is reduced by denitrification. Control software architecture was designed which permits the heterogeneous control of system hardware using traditional feedback control, and quantitative and qualitative models of various system features. Model-based feed forward control entails prediction of future systems in states and automated regulation of system parameters to achieve desired and avoid undesirable system states. A bacterial growth rate model based on the classic Monod model of saturation kinetics was used to evaluate the response of several individual denitrifying species to varying environmental conditions. The system and models are now being applied to mixed microbial communities harvested from the root zone of a hydroponic growth chamber. The use of a modified Monod organism interaction model was evaluated as a means of achieving more accurate description of the dynamic behavior of the communities. A minimum variance parameter estimation routine was also' used to calibrate the constant parameters in the model by iterative evaluation of substrate (nitrate) uptake and growth kinetics. This representation of processes and interactions aids in the formulation of control laws. The feed forward control strategy being developed will increase system autonomy, reduce crew intervention and limit the accumulation of undesirable waste products (NOx).

Smernoff, David T.↗
NASA NTRS1994

Robust stability of second-order systems

Nonlinear control using feedback linearization or inverse dynamics for robotic manipulators yields good results in the absence of modeling uncertainty. However, modeling uncertainties due to unknown joint friction coefficients and payload variations can give rise to undesirable characteristics when these control systems are implemented. It is shown how passivity concepts can be used to supplement the feedback linearization control design technique, in order to make it robust with respect to the uncertain effects mentioned above. Results are obtained for space manipulators with freely floating base; however, they are applicable to fixed base manipulators as well. The controller guarantees asymptotic tracking of the joint variables. Closed-loop simulation results are illustrated for planar space manipulators for cases where uncertainty exists in friction modeling and payload inertial parameters.

Chuang, C.-H.↗
NASA NTRS1973

On the stabilization of decentralized control systems.

This paper considers the problem of stabilizing a linear time-variant multivariable system by using several local feedback control laws. Each local feedback control law depends only on partial system outputs. A necessary and sufficient condition for the existence of local control laws with dynamic compensation to stabilize a given system is derived. This condition is stated in terms of a new notion, called fixed modes, which is a natural generalization of the well-known concept of uncontrollable modes and unobservable modes that occur in centralized control system problems. A procedure that constructs a set of stabilizing feedback control laws is given.

Wang, S.-H.↗
NASA NTRS2007

Loss-of-Control-Inhibitor Systems for Aircraft

Systems to provide improved tactile feedback to aircraft pilots are being developed to help the pilots maintain harmony between their control actions and the positions of aircraft control surfaces, thereby helping to prevent loss of control. A system of this type, denoted a loss-of-control-inhibitor system (LOCIS) can be implemented as a relatively simple addition to almost any pre-existing flight-control system. The LOCIS concept offers at least a partial solution to the problem of (1) keeping a pilot aware of the state of the control system and the aircraft and (2) maintaining sufficient control under conditions that, as described below, have been known to lead to loss of control. Current commercial aircraft exhibit uneven responses of primary flight-control surfaces to aggressive pilot control commands, leading to deterioration of pilots ability to control their aircraft. In severe cases, this phenomenon can result in loss of control and consequent loss of aircraft. For an older aircraft equipped with a purely mechanical control system, the loss of harmony between a pilot s command action and the control- surface response can be attributed to compliance in the control system (caused, for example, by stretching of control cables, flexing of push rods, or servo-valve distortion). In a newer aircraft equipped with a fly-by-wire control system, the major contributions to loss of harmony between the pilot and the control surfaces are delays attributable to computer cycle time, control shaping, filtering, aliasing, servo-valve distortion, and actuator rate limiting. In addition, a fly-by-wire control system provides no tactile feedback that would enable the pilot to sense such features of the control state as surface flutter, surface jam, position limiting, actuator rate limiting, and control limiting imposed by the aircraft operational envelope. Hence, for example, when a pilot is involved in aggressive closed-loop maneuvering, as when encountering a wake-vortex upset on final landing approach, the control-surface delay can lead to loss of control. Aggressive piloting can be triggered and exacerbated by control-system anomalies, which the pilot cannot diagnose because of the lack of symptoms caused by the absence of feedback through the controls. The purpose served by a LOCIS is to counteract these adverse effects by providing real-time feedback that notifies the pilot that the aircraft is tending to lag the pilot s commands. A LOCIS (see figure) includes cockpit control input-position sensors, control-surface output-position sensors, variable dampers (for example, shock absorbers containing magneto-rheological fluids such that the damping forces can be varied within times of the order of milliseconds by varying applied magnetic fields) attached to the cockpit control levers, electromagnet coils to apply the magnetic fields, and feedback control circuits to drive the electromagnet coils. The feedback control gains are chosen so that the current applied to each electromagnet coil results in a damping force that increases in a suitable nonlinear manner (e.g., exponentially) with the difference between the actual and commanded positions of the affected control surface. The increasing damping force both alerts the pilot to the onset of a potentially dangerous situation and resists the pilot s effort to command a control surface to change position at an excessive rate

AHarrah, Ralph C.↗
NASA NTRS2021

A Learn-to-Fly Approach for Adaptively Tuning Flight Control Systems

A method is presented for adaptively tuning feedback control gains in a flight control system to achieve desired closed-loop performance. The method combines efficient aircraft parameter estimation, for identifying closed-loop dynamics models, with online nonlinear optimization, for sequentially perturbing and updating control gains to improve performance. Access to flight measurements and the control gains is required, but no prior information about the aircraft dynamics or the flight control architecture is needed. After the procedure, the optimized control gains (with uncertainties), the open-loop dynamics model, and the closed-loop dynamics model are available. The method is demonstrated for tuning a longitudinal stability augmentation system using a realistic nonlinear flight dynamics simulation of a subscale airplane. Convergence was attained using five maneuvers that spanned approximately one minute of flight test time. Although shown for a relatively simple case, the method is general and can be applied to other aircraft, axes of motion, performance metrics, and control system designs.

Adaptive tuning↗
NASA NTRS1989

Optimal feedback control of infinite-dimensional parabolic evolution systems - Approximation techniques

A general approximation framework is discussed for computation of optimal feedback controls in linear quadratic regular problems for nonautonomous parabolic distributed parameter systems. This is done in the context of a theoretical framework using general evolution systems in infinite dimensional Hilbert spaces. Conditions are discussed for preservation under approximation of stabilizability and detectability hypotheses on the infinite dimensional system. The special case of periodic systems is also treated.

Banks, H. T.↗
NASA NTRS1975

Performance analysis of the advanced thermal control flight experiment

Flight data for the different operational modes of the advanced thermal control flight experiment are presented and compared with ground-test data. Performance of the system with feedback control is compared to performance without such control, and performances of the individual components are analyzed. Finally, changes in performance from launch through March 31, 1975, are discussed and analyzed. All thermal control components are performing as predicted for the existing flight environment. However, the daily reservoir and radiator temperatures during peak solar input are greater than those experienced in ground acceptance tests. These increased temperatures have resulted in a loss of control by the feedback-controlled variable-conductance heat pipe for several hours around the period of maximum insolation. The higher temperatures are apparently due to contamination and/or degradation of the second-surface mirrors which cover the reservoir and radiator.

Kirkpatrick, J. P.↗
NASA NTRS1988

Control strategies

Techniques for improving the performance of robotic-manipulator path-control systems comprising independent SISO feedback controllers for each joint are discussed and illustrated with block diagrams, reviewing the results of recent analytical investigations. Topics examined include the servo design for a single link, the equations of motion for manipulators, SISO servo design for multiple links, inverse methods, pole placement with compensation of the gravity terms, linear state-feedback control based on the perturbation equations, and adaptive control methods. Consideration is given to variable-structure systems, suboptimal controllers, and the optimal-design-strategy approach.

Wang, J. C.↗