SEARCH · Engineering Papers

Results for “fast ions”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

All sources NASA NTRS DOE OSTI

NASA NTRS1998

The Relationship of Ion Beams and Fast Flows in the Plasma Sheet Boundary Layer

We report new findings on the behavior of plasmas in the vicinity of the plasma sheet boundary layer (PSBL). A large geometrical factor detector on WIND (3D plasma experiment) has discovered a unidirectional ion beam streaming in the tailward direction missed by previous observations. This tailward beam is as intense as the earthward streaming beam and it is found just inside the outer edge of the PSBL where earthward streaming beams are observed. The region where this tailward beam is observed includes an isotropic plasma component which is absent in the outer edge where earthward streaming beams are found. When these different distributions are convolved to calculate the velocity moments, fast flows (greater than 400 km/s) result in the earthward direction and much slower flows (less than 200 km/s) in the tailward direction. These new findings are substantially different from previous observations. Thus, the interpretation of fast flows and earthward and counterstreaming ion beams in terms of a neutral line model must be reexamined.

Parks, G. K.↗

DOE OSTI2021

Operando Analysis of Gas Evolution in TiNb 2 O 7 (TNO)-Based Anodes for Advanced High-Energy Lithium-Ion Batteries under Fast Charging

TiNb 2 O 7 (TNO) is regarded as one of the promising next-generation anode materials for lithium-ion batteries (LIBs) due to its high rate capabilities, higher theoretical capacity, and higher lithiation voltage. Furthermore, this enables the cycling of TNO-based anodes under extreme fast charging (XFC) conditions with a minimal risk of lithium plating compared to that of graphite anodes. Here, the gas evolution in real time with TNO-based pouch cells is first reported via operando mass spectrometry. The main gases are identified to be CO 2 , C 2 H 4 , and O 2 . A solid–electrolyte interphase is detected on TNO, which continues evolving, forming, and dissolving with the lithiation and delithiation of TNO. The gas evolution can be significantly reduced when a protective coating is applied on the TNO particles, reducing the CO 2 and C 2 H 4 evolution by ~2 and 5 times, respectively, at 0.1C in a half-cell configuration. The reduction on gas generation in full cells is even more pronounced. The surface coating also enables 20% improvement in capacity under XFC conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

How Fast Can a Li-Ion Battery Be Charged? Determination of Limiting Fast Charging Conditions

Fast-charge protocols that prevent lithium plating are needed to extend the life span of lithium-ion batteries. Here, we describe a simple experimental method to estimate the minimum charging time below which it is simply impossible to avoid plating at a given temperature. We demonstrate that, by gauging and correcting the ohmic drop that is intrinsic to reference electrodes, the local potential at the anode surface can be reasonably approximated. This finer anode control enables the determination of the maximum average rate at which lithium deposition can be mitigated, establishing realistic boundaries that can inform the development of advanced charging protocols.

25 ENERGY STORAGE↗

DOE OSTI2022

Examination of stiff ion temperature gradient mode physics in simulations of DIII-D H-mode transport

A systematic evaluation of gyrokinetic and gyrofluid model predictions of ion temperature gradient (ITG) stability and transport using parameters from DIII-D high confinement mode (H-mode) plasmas has been performed. The nonlinear CGYRO code is used to make the gyrokinetic predictions, and the quasilinear TGLF model for the corresponding gyrofluid predictions. The assessments are made at three radii (normalized toroidal flux ρtor = 0.4, 0.55, and 0.7) in three different plasma scenarios with varying levels of neutral beam heating and torque. For each of the nine cases (3 radii × 3 scenarios) considered, ITG turbulence is found to be the dominant long-wavelength instability and transport mechanism. The inclusions of both transverse magnetic fluctuations and dynamic fast beam ions are stabilizing for all cases considered, with strongest effects seen at ρor = 0.4 where the fast ion population and normalized plasma pressure β = 2μ0nT/B2 are highest. The further inclusion of parallel magnetic fluctuations does not have a meaningful impact on the ITG turbulence in these scenarios, but does destabilize (in combination with fast ions) new high-frequency instabilities at ρtor = 0.4 in the high power scenarios. In each case the linear and nonlinear ITG critical gradients are predicted to be lower than the measured ITG scale lengths and their associated uncertainties. Inclusion of equilibrium flow shear in the transport predictions generally leads to an upshift in effective critical gradient rather than a qualitative change in the predicted stiffness, with stronger responses typically seen in the gyrokinetic predictions than in the gyrofluid results. However, in most cases these upshifted gradients still remain below the measured values and their uncertainties. Although the predicted critical gradients are below the measured gradients, both models predicted flux-matching gradients consistent with measured values in six of the nine cases considered, with no clear systematic over- or underprediction. Thus, while the experimental ion temperature profiles do not appear to be closely pinned to the ITG critical gradient, both gyrokinetic and gyrofluid models are able to accurately match the measured gradients reasonably well in most cases.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1988

A fast and accurate method for evaluating the nonrelativistic free-free Gaunt factor for hydrogenic ions

A fast method for obtaining a two-dimensional Chebyshev expansion of the nonrelativistic hydrogenic free-free Gaunt factor is presented which gives a maximum relative error of 0.7 percent over a wide range of temperatures and frequencies. The expansion derived by Karzas and Latter (1961) is used to derive primary values of the free-free Gaunt factor as a function of the initial and final electron energies. Thermal averages have been numerically computed and are presented in tabular form in intervals of 0.25 dex.

Hummer, D. G.↗

DOE OSTI2021

Design Considerations for Fast Charging Lithium Ion Cells for NMC/MCMB Electrode Pairs

Lithium ion cells that can be quickly charged are of critical importance for the continued and accelerated penetration of electric vehicles (EV) into the consumer market. Considering this, the U.S. Department of Energy (DOE) has set a cell recharge time goal of 10–15 min. The following study provides an investigation into the effect of cell design, specifically negative to positive matching ratio (1.2:1 vs. 1.7:1) on fast charging performance. By using specific charging procedures based on negative electrode performance, as opposed to the industrial standard constant current constant voltage procedures, we show that the cells with a higher N:P ratio can be charged to ~16% higher capacity in the ten-minute time frame. Cells with a higher N:P ratio also show similar cycle life performance to those with a conventional N:P ratio, despite the fact that these cells experience a much higher irreversible capacity loss, leading to a lower reversible specific capacity.

25 ENERGY STORAGE↗

DOE OSTI2023

Improved ion heating in fast ignition by pulse shaping

The fast ignition paradigm for inertial fusion offers increased gain and tolerance of asymmetry by compressing fuel at low entropy and then quickly igniting a small region. Because this hotspot rapidly disassembles, the ions must be heated to ignition temperature as quickly as possible, but most ignitor designs directly heat electrons. A constant-power ignitor pulse, which is generally assumed, is suboptimal for coupling energy from electrons to ions. Using a simple model of a hotspot in isochoric plasma, a novel pulse shape to maximize ion heating is presented in analytical form. Bounds are derived on the maximum ion temperature attainable by electron heating only. Moreover, arranging for faster ion heating allows a smaller hotspot, improving fusion gain. As a result, under representative conditions, the optimized pulse can reduce ignition energy by over 20%.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

DOE OSTI2022

Fast wave interferometer for ion density measurement on DIII-D

=A fast wave interferometer (FWI), which can measure ion mass density, has been developed on DIII-D for its use on future fusion reactors, as well as for the study of ion behavior in current plasma devices. The frequency of the fast waves used for the FWI is around 60 MHz, and require antennas and coaxial cables or waveguides, which, unlike traditional mirror-based optical interferometers, are less susceptible to neutron/gamma-ray radiation and are relatively immune to impurity deposition and erosion as well as alignment issues. The bulk ion density evaluated using FWI show good agreement with that derived from CO 2 interferometry within about 15%. When the ion mass density measurement by FWI is combined with an electron density measurement from CO 2 interferometry, Z eff measurements are also enabled and are in agreement with those from visible Bremsstrahlung measurements. Additionally, large-bandwidth FWI measurements clearly resolve 10–100 kHz coherent modes and demonstrate its potential as a core fluctuation diagnostic, sensitive to both magnetic and ion density perturbations.

Instruments & Instrumentation↗

NASA NTRS1984

Abundances and spectra of superathermal H(+), He(++) and heavy ions in a fast moving plasma structure (plasmoid) in the distant geotail

An ISEE-3 Geotail Mission sensor has furnished data on a 16-min particle intensity increase in the distant magnetotail from which rest frame distribution functions have been deduced for 3-150 keV/amu H(+), He(++), and ions with a charge state greater than 3. The event was characterized by isotropic electron distributions and is identified as a tailward-moving plasmoid. These suprathermal ions are convected nearly tailward at an average speed of 1000 + or - 50 km/sec and have an energy density of 150 eV/cu cm. A crosstail expansion speed of about 80 km/sec is indicated.

Gloeckler, G.↗

DOE OSTI2021

Defect–Concentration–Mediated T–Nb 2 O 5 Anodes for Durable and Fast–Charging Li–Ion Batteries

Metastable orthorhombic niobium pentoxide (T-Nb 2 O 5 ) is a promising anode to fulfill the requirements for high-rate Li-ion batteries (LIBs). Stoichiometric T-Nb 2 O 5 is plagued by low electric conductivity and particle pulverization after repeated charge/discharge processes. In this work, oxygen vacancies are implanted into T-Nb 2 O 5 particles via acid immersion of Nb 2 O 5 ·nH 2 O with the formation of Lewis acid sites. The multiple characterizations and simulations reveal the lengthening of Nb–O bonds, and the transformation from NbO 7 pentagonal bipyramids and NbO 6 tetragonal bipyramids in T-Nb 2 O 5–x . The enrichment of oxygen vacancies endows T-Nb 2 O 5–x with higher electric conductivity, better electrochemical kinetics, larger pseudocapacitive contribution. O-doped graphitic C 3 N 4 is creatively proposed as a trace oxygen pump to repair excessive oxygen vacancies, and it also serves as a sacrifice template for Nb 2 O 5–x growth to construct a porous and monolithic electrode network. Defect-modulated Nb 2 O 5–x displays extraordinary cycling stability (164 mAh g –1 at 5 C after 1100 cycles), high capacity retention (104 mAh g –1 ) at an ultrahigh rate (25 C), and large areal capacity (0.74 mAh cm –2 ) under high mass loading (4 mg cm –2 ). The practical prospect is proved by Nb 2 O 5–x /LiNi 0.8 Co 0.1 Mn 0.1 O 2 full cells with high average platform (2.12 V) and high specific capacity (229 mAh g –1 ). Finally, the oxygen-defect modulation strategy on oxide anodes provides an alternative solution to fast-charging and durable LIBs.

25 ENERGY STORAGE↗

DOE OSTI2021

Methodologies for Design, Characterization and Testing of Electrolytes that Enable Extreme Fast Charging of Lithium-ion Cells

Selection, testing and validation of electrolyte candidates for Li-ion cells are discussed, based on a 10-minute target for extreme fast charge (XFC). A combination of modeling and laboratory measurements create a timely and synergistic approach to identifying candidate electrolyte formulations. Multi-solvent systems provide a balanced set of properties, wherein lower molecular-weight solvents offer reduced viscosity, increased species diffusivity, and mitigation of concentration polarization at high charge rates. Carefully selected formulations can exhibit peak conductivity and usable conductivity range of two to three times that of the baseline EC-EMC (3:7, wt.) + LiPF 6 . Candidates are also chosen based on stability and longevity within the cell environment. Lab testing coincides with property predictions from the Advanced Electrolyte Model (AEM) and a macro-scale cell model. Furthermore, cell testing utilized coin and pouch cells having NMC532 or NMC811 cathodes with graphite electrodes. Results indicate combinations of low-molecular weight solvents are key for fast-charge electrolytes as they extend the useful conductivity range to both low and higher salt concentrations, and possess higher self-diffusivities compared to conventional solvents. This reduces impacts from concentration polarization. The choice of electrolyte also influences the tendency for lithium metal deposition at the anode, as showcased by experimental and modeling results herein.

25 ENERGY STORAGE↗

DOE OSTI2022

Conformal Pressure and Fast-Charging Li-Ion Batteries

Batteries capable of extreme fast-charging (XFC) are a necessity for the deployment of electric vehicles. Material properties of electrodes and electrolytes along with cell parameters such as stack pressure and temperature have coupled, synergistic, and sometimes deleterious effects on fast-charging performance. We develop a new experimental testbed that allows precise and conformal application of electrode stack pressure. We focus on cell capacity degradation using single-layer pouch cells with graphite anodes, LiNi 0.5 Mn 0.3 Co 0.2 O 2 (NMC532) cathodes, and carbonate-based electrolyte. In the tested range (10–125 psi), cells cycled at higher pressure show higher capacity and less capacity fading. Additionally, Li plating decreases with increasing pressure as observed with scanning electron microscopy (SEM) and optical imaging. While the loss of Li inventory from Li plating is the largest contributor to capacity fade, electrochemical and SEM examination of the NMC cathodes after XFC experiments show increased secondary particle damage at lower pressure. We infer that the better performance at higher pressure is due to more homogeneous reactions of active materials across the electrode and less polarization through the electrode thickness. Our study emphasizes the importance of electrode stack pressure in XFC batteries and highlights its subtle role in cell conditions.

25 ENERGY STORAGE↗

DOE OSTI2020

Advanced electrolytes for fast-charging high-voltage lithium-ion batteries in wide-temperature range

LiNixMnyCo1-x-yO2 (NMC) cathode materials with Ni=0.8 have attracted great interest for application in high energy-density lithium (Li)-ion batteries (LIBs) because of their high specific capacities at high voltages. However, the practical application of Ni-rich NMC in LIBs under high charge voltages (e.g. 4.4 V and above) still faces big challenges due to the severe capacity fading, which is directly related to the instability of the cathode/electrolyte interface. In this work, we develop new localized high-concentration electrolytes (LHCEs) based on carbonate solvents, which are compatible with graphite (Gr) anode and have a high oxidation potential over 4.9 V vs. Li/Li+. The optimal LHCE enables the Gr||NMC811 cells with 2.8 mAh cm-2 cathode areal capacity loading to achieve an excellent cycling stability over 600 cycles with a capacity retention of 94.2 % under a charge cut-off voltage of 4.4 V at 25 ?C, good rate capabilities under fast charging or discharging up to 3C rate, and superior low-temperature discharge performance down to -30 ?C with a capacity retention of 85.6% at C/5 rate. The findings in this work shed light a very promising strategy to develop new electrolytes for practical high-energy LIBs with Ni-rich NMC cathodes.

Zhang, Xianhui↗

DOE OSTI2022

Revealing Fast Cu-Ion Transport and Enhanced Conductivity at the CuInP 2 S 6 –In 4/3 P 2 S 6 Heterointerface

Van der Waals layered ferroelectrics, such as CuInP 2 S 6 (CIPS), offer a versatile platform for miniaturization of ferroelectric device technologies. Control of the targeted composition and kinetics of CIPS synthesis enables the formation of stable self-assembled heterostructures of ferroelectric CIPS and nonferroelectric In 4/3 P 2 S 6 (IPS). Here, we use quantitative scanning probe microscopy methods combined with density functional theory (DFT) to explore in detail the nanoscale variability in dynamic functional properties of the CIPS-IPS heterostructure. Within, we report evidence of fast ionic transport which mediates an appreciable out-of-plane electromechanical response of the CIPS surface in the paraelectric phase. Further, we map the nanoscale dielectric and ionic conductivity properties as we thermally stimulate the ferroelectric-paraelectric phase transition, recovering the local dielectric behavior during this phase transition. Finally, aided by DFT, we reveal a substantial and tunable conductivity enhancement at the CIPS/IPS interface, indicating the possibility of engineering its interfacial properties for next generation device applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Ionic Liquid–Directed Nanoporous TiNb 2 O 7 Anodes with Superior Performance for Fast–Rechargeable Lithium–Ion Batteries

Nanoporous TiNb 2 O 7 (NPTNO) material is synthesized by a sol–gel method with an ionic liquid (IL) as the nanoporous structure directing template. NPTNO exhibits a high reversible capacity of 210 mAh g –1 even at the charging rate of 50 C and an excellent cyclability of half-cell capacity retention of 74% for 1000 cycles at 5 C and LiNi 0.5 Mn 1.5 O 4 -coupled full-cell capacity retentions of 81% and 87% for 1000 cycles at 1 C and 2 C, respectively. The studies of the 1000 cycled NPTNO electrode illustrate that the IL-directed mesoporous structure can enhance the cyclability of NPTNO cells due to the alleviation of repetitive mechanical stress and volume fluctuation induced by the repetitive Li + insertion-extraction processes. The measured Li + diffusion coefficients from the galvanostatic intermittent titration technique suggest that the IL-templating strategy indeed ensures the fast rechargeability of NPTNO cells based on the fast Li + diffusion kinetics. Benefitting from the nanoporous structure, NPTNO with unhindered Li + diffusion pathways achieves a superior rate capability in the titanium-based oxide materials and the best full-cell cyclability in the TNO materials. Furthermore, the templating potential of IL is demonstrated, and the superb electrochemical performance establishes the IL-directed NPTNO as a promising anode candidate for fast-rechargeable LIBs.

25 ENERGY STORAGE↗

DOE OSTI2021

Quantification of heterogeneous, irreversible lithium plating in extreme fast charging of lithium-ion batteries

Realization of extreme fast charging (XFC, ≤15 minutes) of lithium-ion batteries is imperative for the widespread adoption of electric vehicles. However, dramatic capacity fading is associated with XFC, limiting its implementation. To quantitatively elucidate the effects of irreversible lithium plating and other degradation mechanisms on the cell capacity, it is important to understand the links between lithium plating and cell degradation at both the local and global (over the full cell) scales. Here, we study the nature of local lithium plating after hundreds of XFC cycles (charging C-rates ranging from 4C to 9C) in industrially-relevant pouch cells using spatially resolved X-ray diffraction. Our results reveal a spatial correlation at the mm scale between irreversible lithium plating on the anode, inactive lithiated graphite phases, and local state-of-charge of the cathode. In regions of plated lithium, additional lithium is locally and irreversibly trapped as lithiated graphite, contributing to the loss of lithium inventory (LLI) and to a local loss of active anode material. The total LLI in the cell from irreversibly plated lithium is linearly correlated to the capacity loss in the batteries after XFC cycling, with a non-zero offset originating from other parasitic side reactions. Finally, at the global (cell) scale, LLI drives the capacity fade, rather than electrode degradation. We anticipate that the understanding of lithium plating and other degradation mechanisms during XFC gained in this work will help lead to new approaches towards designing high-rate batteries in which irreversible lithium plating is minimized.

25 ENERGY STORAGE↗

DOE OSTI2022

Overcoming the Intrinsic Limitations of Fast Charging Lithium‐Ion Batteries Using Integrated Acoustic Streaming

A lithium‐ion battery's maximum charge rate and energy density are intrinsically limited by the ion diffusion rate in the electrolyte. Most research focuses on materials science solutions to this problem, with gradual improvement over the years. A mechanical solution is proposed to integrate an MHz‐order frequency surface acoustic wave (SAW) device into an existing 1.8 Ah multilayered Li‐ion pouch cell to enhance the ion diffusion rate and the overall battery performance. Both the charging rate and cycling lifetime are improved from SAW. At a 6C (10 min) charge and C/3 discharge rate, typical of electric vehicle applications, integrating SAW into the Li‐ion cell doubles the energy density and maintains at least 72% of the battery's initial capacity after 2000 cycles. Moreover, using SAW quantifiably reduces battery degradation in these conditions as determined by optical imaging, scanning electron microscopy, X‐ray diffraction, and neutron diffraction. The use of SAW appears to offer a method to avoid undesirable Li metal plating on the graphite anode during charging, and leads to a much longer battery lifetime and good charge capacity, all despite rapid charging.

Huang, An↗

DOE OSTI2022

Enhanced performance in fusion plasmas through turbulence suppression by megaelectronvolt ions

Alpha particles with energies on the order of megaelectronvolts will be the main source of plasma heating in future magnetic confinement fusion reactors. Instead of heating fuel ions, most of the energy of alpha particles is transferred to electrons in the plasma. Furthermore, alpha particles can also excite Alfvénic instabilities, which were previously considered to be detrimental to the performance of the fusion device. In this work, we report improved thermal ion confinement in the presence of megaelectronvolts ions and strong fast ion-driven Alfvénic instabilities in recent experiments on the Joint European Torus. Herein, detailed transport analysis of these experiments reveals turbulence suppression through a complex multi-scale mechanism that generates large-scale zonal flows. This holds promise for more economical operation of fusion reactors with dominant alpha particle heating and ultimately cheaper fusion electricity.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗