Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “external control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Robust cooperative control strategy for a platoon of connected and autonomous vehicles against sensor errors and control errors simultaneously in a real-world driving environment

In a real-world driving environment, a platoon of connected and autonomous vehicles (CAVs) is subject to many internal and external disturbances, resulting in uncertain vehicle dynamics. In general, the disturbances can be categorized into two types: disturbances due to vehicle sensor errors (e.g., GPS error) and disturbances due to vehicle control errors (e.g., actuator delay). In the literature, many control strategies have been proposed to improve the robustness of the CAV platoon against uncertain vehicle dynamics induced by these disturbances. However, most of these strategies only consider one type of disturbance and cannot tackle both types of disturbances simultaneously. Furthermore, they are designed to maximize the benefits of each vehicle in the platoon independently, which can deteriorate the performance of the platoon. Here, to address these problems, this study proposes a robust cooperative control (RCC) strategy to maneuver the vehicles in the platoon cooperatively to counteract the impacts of both types of disturbances. The RCC strategy is developed based on a minimax problem, where the maximization subproblem seeks to find the worst inputs for the uncertainty terms in the vehicle dynamics equation to minimize the platoon performance, while the minimization subproblem seeks to find the optimal control decisions for all subsequent vehicles to maximize the platoon performance in the worst case. To solve the minimax problem, this study proposes a globally convergent solution algorithm. It can solve the minimax problem very efficiently to enable real time deployment of the RCC strategy. Numerical application indicates that compared to the existing methods, the RCC strategy can dramatically improve the robustness of the CAV platoon against the uncertain vehicle dynamics induced by both vehicle state detection errors and vehicle control errors. Therefore, it can maneuver the CAV platoon safely and efficiently in a real-world driving environment.

33 ADVANCED PROPULSION SYSTEMS↗

Optical Control of Adaptive Nanoscale Domain Networks

Adaptive networks can sense and adjust to dynamic environments to optimize their performance. Understanding their nanoscale responses to external stimuli is essential for applications in nanodevices and neuromorphic computing. However, it is challenging to image such responses on the nanoscale with crystallographic sensitivity. Here, the evolution of nanodomain networks in (PbTiO 3 ) n /(SrTiO 3 ) n superlattices (SLs) is directly visualized in real space as the system adapts to ultrafast repetitive optical excitations that emulate controlled neural inputs. The adaptive response allows the system to explore a wealth of metastable states that are previously inaccessible. Their reconfiguration and competition are quantitatively measured by scanning x-ray nanodiffraction as a function of the number of applied pulses, in which crystallographic characteristics are quantitatively assessed by assorted diffraction patterns using unsupervised machine-learning methods. The corresponding domain boundaries and their connectivity are drastically altered by light, holding promise for light-programable nanocircuits in analogy to neuroplasticity. Phase-field simulations elucidate that the reconfiguration of the domain networks is a result of the interplay between photocarriers and transient lattice temperature. The demonstrated optical control scheme and the uncovered nanoscopic insights open opportunities for the remote control of adaptive nanoscale domain networks.

36 MATERIALS SCIENCE↗

Expert Elicitation on Wind Farm Control

Wind farm control is an active and growing field of research in which the control actions of individual turbines in a farm are coordinated, accounting for inter-turbine aerodynamic interaction, to improve the overall performance of the wind farm and to reduce costs. The primary objectives of wind farm control include increasing power production, reducing turbine loads, and providing electricity grid support services. Additional objectives include improving reliability or reducing external impacts to the environment and communities. In 2019, a European research project (FarmConners) was started with the main goal of providing an overview of the state-of-the-art in wind farm control, identifying consensus of research findings, data sets, and best practices, providing a summary of the main research challenges, and establishing a roadmap on how to address these challenges. Complementary to the FarmConners project, an IEA Wind Topical Expert Meeting (TEM) and two rounds of surveys among experts were performed. From these events we can clearly identify an interest in more public validation campaigns. Additionally, a deeper understanding of the mechanical loads and the uncertainties concerning the effectiveness of wind farm control are considered two major research gaps.

17 WIND ENERGY↗

Design of an 8-channel 40 GS/s 20 mW/Ch waveform sampling ASIC in 65 nm CMOS

One picosecond timing resolution is the entry point to signature based searches relying on secondary/tertiary vertices and particle identification. We describe PSEC5, an 8-channel 40 GS/s waveform-sampling ASIC in TSMC 65 nm process targetting one picosecond resolution at 20 mW power per channel. Each channel consists of four fast and one slow switched capacitor arrays (SCA), allowing for picosecond time resolution combined with a long effective buffer. Each fast SCA is 1.6 ns long and has a nominal sampling rate of 40 GS/s. The slow SCA is 204.8 ns long and samples at 5 GS/s. Recording of the analog data for each channel is triggered by a fast discriminator capable of multiple triggering during the window of the slow SCA. To achieve a large dynamic range, low leakage, and high bandwidth, the SCA sampling switches are implemented as 2.5 V nMOSFETs controlled by 1.2 V shift registers. Stored analog data are digitized by an external ADC at 10 bits or better. Specifications on operational parameters include a 4 GHz analog bandwidth and a dead time of 20 microseconds, corresponding to a 50 kHz readout rate, determined by the choice of the external ADC. PSEC5 has been submitted for fabrication.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Modulation of Photoinduced Iodine Expulsion in Mixed Halide Perovskites with Electrochemical Bias

Hole trapping at iodine (I) sites in MAPbBr 1.5 I 1.5 mixed halide perovskites (MHP) is responsible for iodine migration and its eventual expulsion into solution. We have now modulated the photoinduced iodine expulsion in MHP through an externally applied electrochemical bias. At positive potentials, electron extraction at TiO 2 /MHP interfaces becomes efficient, leading to hole buildup within MHP films. This improved charge separation, in turn, favors iodine migration as evident from the increased apparent rate constant of iodine expulsion (k expulsion = 0.0030 s –1 ). Conversely, at negative potentials (-0.3 V vs Ag/AgCl) electron–hole recombination is facilitated within MHP, slowing down iodine expulsion by an order of magnitude (k expulsion = 0.00018 s –1 ). The tuning of the EFermi level through external bias modulates electron extraction at the TiO 2 /MHP interface and indirectly controls the buildup of holes, ultimately inducing iodine migration/expulsion. Suppressing iodine migration in perovskite solar cells is important for attaining greater stability since they operate under internal electrical bias.

14 SOLAR ENERGY↗

Sputtered p-Type Cu x Zn 1– x S Back Contact to CdTe Solar Cells

As thin-film cadmium telluride (CdTe) solar cells gain prominence, one particular challenge is optimizing contacts and their interfaces to transfer charge without losses in efficiency. Back contact recombination is still significant and will prevent CdTe solar technology from reaching its full potential in device efficiency, and transparent back contacts have not been developed for bifacial solar technology or multijunction solar cells. To address these challenges, here we investigate sputtered Cu x Zn 1– x S as a p-type semi-transparent back contact material to thin-film polycrystalline CdTe solar cells at Cu concentrations x = 0.30, 0.45, and 0.60. This material is selected for its high hole conductivity (160–2120 S cm –1 ), wide optical band gap (2.25–2.75 eV), and variable ionization potential (approximately 6–7 eV) that can be aligned to that of CdTe. We report that without device optimization, CdTe solar cells with these Cu x Zn 1– x S back contacts perform as well as control cells with standard ZnTe:Cu back contacts. We observe no reduction in external quantum efficiency, low contact barrier heights of approximately 0.3 eV, and carrier lifetimes on par with those of baseline CdTe. These cells are relatively stable over one year in air, with V OC and efficiency of the x = 0.30 cell decreasing by only 1 and 3%, respectively. Using scanning electron microscopy and scanning transmission electron microscopy to investigate the Cu x Zn 1– x S/CdTe interface, we demonstrate that the Cu x Zn 1– x S layer segregates into a bilayer of Cu-Te-S and Zn-Cd-S, and thermodynamic reaction calculations support these findings. Despite its bilayer formation, the back contact still functions well. This investigation explains some of the physical mechanisms governing the device stack, inspires future work to understand interfacial chemistry and charge transfer, and elicits optimization to achieve higher-efficiency CdTe cells.

14 SOLAR ENERGY↗

Physics basis for the reference flat-top plasma scenario in the ST–E1 fusion power plant

As part of the U.S. Department of Energy’s Milestone-Based Fusion Energy Development Program, Tokamak Energy has completed the pre-concept design of the ST–E1 fusion power plant. ST–E1 is envisaged to operate in two phases: a pilot plant phase, targeting sustained net power production of 300 - 500 MWe for a duration >1 hr, followed by a commercial power plant phase targeting steady-state operations and a normalised overnight capital cost of ⩽12 000 $\$$/kWe. The design process adopted was highly iterative, integrating all major plant systems and progressing in a phased fidelity approach. At the pre-conceptual stage, the emphasis has been on exploring the design space, identifying the main system-level trade-offs, and making the key decisions that define the overall plant concept, rather than optimising a single operating point. This paper, part of a focused collection detailing the ST–E1 pre-concept design, addresses the development of a series of reference flat-top plasma operating points for the pilot plant phase. A modelling workflow was established to develop and assess candidate plasma design points and explore key dependencies. The workflow includes integrated core plasma modelling, magnetohydrodynamic (MHD) stability assessment, equilibrium generation, scrape-off-layer and exhaust modelling, heating & current drive design and optimisation, and turbulent transport modelling. Using this framework, the impact of several key parameters on the flat-top operating space was investigated, including the density limit, core radiation fraction and divertor power loading, level of external heating and curent drive power and assumed pedestal characteristics. The MHD stability, controllability and micro-stability characteristics of these plasmas were also analysed. These investigations informed the definition of a set of fully non-inductive, flat-top reference operating points that satisfy the high-level ST–E1 mission, including a low and high density case, a case that is stable to resistive wall modes and a case with reduced divertor power loading.

ST–E1↗

Origins of magnetic memory and strong exchange bias bordering magnetic compensation in mixed-lanthanide systems

Here, the unexpected physical phenomena resulting from the seemingly inconsequential substitutions of chemically similar lanthanide elements in the Pr 1-x Gd x ScGe system are exploited to further the understanding of rare-earth magnetism and inform materials design. By directly probing magnetic moments of crystallographically indistinguishable Pr and Gd we solve the puzzles of how an unusual magnetic memory and strong exchange bias emerge at specific, easily predictable chemistries. Both effects are rooted in a robust antiparallel arrangement of large 4f magnetic moments of light and heavy lanthanides. This enables precise control of nearly zero net magnetization either opposed to, or aligned with, the external magnetic field that persists over a wide range of temperatures and fields. Further, spontaneous perturbations in the random distribution of lanthanide ions makes strong exchange bias possible in bulk single-phase compounds bordering magnetic compensation, consequently expanding the materials base beyond artificial magnetic multilayers and broadening the range of potential applications of the phenomenon.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

The Impact of Increased Requirements for Verification Measurements of Category III and IV Receipts

As part of the regular nuclear material accounting and control process, sites that have accountable nuclear material regularly perform measurements of the material in their possession. The expectation for the type of measurements and their frequency is set out in Department of Energy (DOE) Order 474.2, and further detailed in each site’s respective material control and accountability (MC&A) plan and associated controlling documents. The measurements of interest in this report are those performed on external (between DOE sites) transfer receipts of Category III or IV accountable materials. In 2020, a revision of DOE Order 474.2 was proposed that would significantly increase the requirement that measurements be performed upon receipt of material, and further, that those measurements be quantitative verification (rather than qualitative confirmatory) measurements. A survey was performed of DOE sites to discuss the impact on their MC&A measurements program if more rigorous verification measurements requirements for Category III and IV receipts were implemented. An assessment of nondestructive assay (NDA) measurement instruments to meet those needs was also performed. Across the board, sites indicated that personnel and budget would cause the largest impact. Sites which are qualified as Category I/II indicated a reduced impact as these sites already have the measurement capabilities and some personnel but would require the acquisition of additional measurement systems. Category III/IV sites indicated a much larger impact as these sites generally have smaller MC&A programs. A few smaller sites stated a measurement program would need to be created to handle the demand. Calorimetry, quantitative gamma spectroscopy and neutron coincidence counting systems were identified as common systems that could meet the verification measurement requirements. The other, and perhaps larger issue is the need for calibration standards for the calorimetry and neutron coincidence counting systems. It is proposed that a comparative study be performed for ISOCS and ISOTOPICS, qualification of a COTS calorimetry system be performed, and development of an AWCC system that uses a neutron generator.

98 NUCLEAR DISARMAMENT, SAFEGUARDS, AND PHYSICAL P↗

Real Time, In-line Monitoring of Hanford Tank Wastes - Year 1 Report

The team comprised of students, postdocs, early, mid and senior career scientists from Los Alamos National Laboratory, Savanah River National Laboratory, Georgia Tech and Florida International University, with the guidance of H2C, is developing a suite of in-line instruments for the Hanford high level waste (HLW) and low active waste (LAW) processes to provide near-real-time analysis of waste form physical properties and composition. The work builds on results from the recent DOE-ORP, EM Technology Development and other projects that demonstrated promise for the use of real-time in-line monitoring (RTIM) to measure chemical compositions of slurries of up to 20 weight % solids. The goal is for this instrument suite is to substantially reduce the need for sampling for process control. Sample waste, exposure associated with sample analysis, and the demand for an external laboratory facility would be greatly reduced. The throughput of waste treatment systems would be improved by elimination of the downtime caused by waiting for sample results. This translates into reduced process storage as process knowledge will be continuously updated in near-real-time. These breakthrough technologies would significantly reduce the life cycle cost and accelerate the schedule for the Hanford tank waste mission.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Current status and outlook for ATRP

Atom transfer radical polymerization (ATRP) is one of the most often used controlled radical polymerization techniques. It employs very small amounts (ppm) of Cu complexes in the presence of various chemical reducing agents but also external stimuli such as light, electrical current or mechanical forces. It can be carried out in bulk, in solution, and in dispersed media. ATRP has been successfully used to prepare various polymers with controlled architecture and well-defined topology, composition, and functionality, as well as bioconjugates and organic–inorganic hybrids. This article summarizes the current status and also an outlook for ATRP.

ATRP↗

Designed Spin‐Texture‐Lattice to Control Anisotropic Magnon Transport in Antiferromagnets

Abstract Spin waves in magnetic materials are promising information carriers for future computing technologies due to their ultra‐low energy dissipation and long coherence length. Antiferromagnets are strong candidate materials due, in part, to their stability to external fields and larger group velocities. Multiferroic antiferromagnets, such as BiFeO 3 (BFO), have an additional degree of freedom stemming from magnetoelectric coupling, allowing for control of the magnetic structure, and thus spin waves, with the electric field. Unfortunately, spin‐wave propagation in BFO is not well understood due to the complexity of the magnetic structure. In this work, long‐range spin transport is explored within an epitaxially engineered, electrically tunable, 1D magnonic crystal. A striking anisotropy is discovered in the spin transport parallel and perpendicular to the 1D crystal axis. Multiscale theory and simulation suggest that this preferential magnon conduction emerges from a combination of a population imbalance in its dispersion, as well as anisotropic structural scattering. This work provides a pathway to electrically reconfigurable magnonic crystals in antiferromagnets.

36 MATERIALS SCIENCE↗

Gridtrust: Electricity Grid Root-of-Trust Decentralized Supply Chain Cyber-Security (Final Scientific/Technical Report)

GridTrust represents a departure from reliance on a single organization or a single person to multiple organizations and therefore multiple people across organizational structures. The motivating idea behind involving multiple organizations is the increase in security due to human factors. More specifically, the requirement that distinct people in different organizations sign off on a change or an update makes a cyberattack much less likely due to the inherent requirement that both organizations be penetrated and fooled. GridTrust focuses on the software update process as the primary exemplar for the research and development work. A novel hardware-based technology referred to as a Physical Unclonable Function (PUF) provides a microchip Root-of-Trust (RoT), i.e., a starting point for verifying that the hardware being communicated with is the hardware the control center believes the hardware to be. As a result, staff at power grid control centers can ensure the accurate and reliable identification of hardware devices from the outset. The GridTrust protocol introduces two key innovations, as detailed in this report. Firstly, the utilization of a PUF as a root-of-trust in the initial phase of a software or firmware update. Secondly, the application of multiple cryptographic signatures from two or more organizations to the update binary. These signatures are verified before implementing the update on a power grid device in the field. In terms of GridTrust hardware design, this report outlines two main components. The first is the GridTrust Native Device, integrating PUF technology intrinsically into the hardware device itself. The second is the GridTrust Interfacing Device, which incorporates PUF technology and multiple cryptographic signatures. These signatures are cross-checked within a separate hardware positioned between the power grid control center and the legacy power grid device, functioning as an intermediary. While the GridTrust Interfacing Device offers the advantage of being applicable to existing power grid equipment, it may have reduced security if the intermediary component is targeted. On the other hand, the GridTrust Native Device boasts increased security due to protocol integration within a unified form factor. The effectiveness of GridTrust technology has been extensively demonstrated, with multiple external red-team attackers unable to breach GridTrust's security measures. This was observed both in controlled laboratory settings during Phase 1 of the project and in real-world conditions within a City of Marietta substation during Phase 2 of the project.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Overscreening, Coion-Dominated Electroosmosis, and Electric Field Strength Mediated Flow Reversal in Polyelectrolyte Brush Functionalized Nanochannels

Controlling the direction and strength of nanofluidic electrohydrodyanmic transport in the presence of an externally applied electric field is extremely important in a number of nanotechnological applications. Here, we employ all-atom molecular dynamics simulations to discover the possibility of changing the direction of electroosmotic (EOS) liquid flows by merely changing the electric field strength in a nanochannel functionalized with polyelectrolyte (PE) brushes. In exploring this, we have uncovered three facets of nanoconfined PE brush behavior and resulting EOS transport. First, we identify the onset of an overscreening effect: such overscreening refers to the presence of more counterions (Na + ) within the brush layer than needed to neutralize the negative brush charges. Accordingly, as a consequence of the overscreening, in the bulk liquid outside the brush layer, there is a greater number of co-ions (Cl – ) than counterions in the presence of an added salt (NaCl). Second, this specific ion distribution ensures that the overall EOS flow is along the direction of motion of the co-ions. Such co-ion-dictated EOS transport directly contradicts the notion that EOS flow is always dictated by the motion of the counterions. Finally, for large-enough electric fields, the brush height reduces significantly, causing some of the excess overscreening-inducing counterions to squeeze out of the PE brush layer into the brush-free bulk. As a result, the overscreening effect disappears and the number of co-ions and counterions outside the PE brush layer become similar. Despite that there is an EOS transport, this EOS transport, unlike the standard EOS transport that occurs due to the imbalance of the co-ions and counterions, occurs since a larger residence time of the water molecules in the first solvation shell of the counterions (Na + ) ensures a water transport in the direction of motion of the counterions. In this work, the net effect is the reversal of the direction of the EOS transport by merely changing the strength of the electric field.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

THz generation by exchange-coupled spintronic emitters

Abstract The mechanism of THz generation in ferromagnet/metal (F/M) bilayers has been typically ascribed to the inverse spin Hall effect (ISHE). Here, we fabricated Pt/Fe/Cr/Fe/Pt multilayers containing two back-to-back spintronic THz emitters separated by a thin ( t Cr ≤ 3nm) wedge-shaped Cr spacer. In such an arrangement, magnetization alignment of the two Fe films can be controlled by the interplay between Cr-mediated interlayer exchange coupling (IEC) and an external magnetic field. This in turn results in a strong variation of the THz amplitude A , with A ↑ ↓ reaching up to 14 times A ↑ ↑ (arrows indicate the relative alignment of the magnetization of the two magnetic layers). This observed functionality is ascribed to the interference of THz transients generated by two closely spaced THz emitters. Moreover, the magnetic field dependence A ( H ) shows a strong asymmetry that points to an additional performance modulation of the THz emitter via IEC and multilayer design.

Adam, Roman↗

High-Sensitivity rf Detection Using an Optically Pumped Comagnetometer Based on Natural-Abundance Rubidium with Active Ambient-Field Cancellation

To detect a specific radio-frequency (rf) magnetic field, rf optically pumped magnetometers (OPMs) require a static magnetic field to set the Larmor frequency of the atoms equal to the frequency of interest. However, unshielded and variable magnetic field environments (e.g., an rf OPM on a moving platform) pose a problem for rf OPM operation. Here, we demonstrate the use of a natural-abundance rubidium vapor to make a comagnetometer to address this challenge. Our implementation builds upon the simultaneous application of several OPM techniques within the same vapor cell. First, we use a modified implementation of an OPM variometer based on 87 Rb to detect and actively cancel unwanted external fields at frequencies ≲60 Hz using active feedback to a set of field control coils. In this experiment, we exploit this stabilized field environment to implement a high-sensitivity rf magnetometer using 85 Rb. Using this approach, we demonstrate the ability to measure rf fields with a sensitivity of approximately 9 fT Hz -1/2 inside a magnetic shield in the presence of an applied field of approximately 20 μT along three mutually orthogonal directions. This demonstration opens up a path toward completely unshielded operation of a high-sensitivity rf OPM.

47 OTHER INSTRUMENTATION↗

High-Temperature Wireless Sensor Platform Powered by Energy Scavenging

This paper reports on the development of key components required for a self-powered oscillator unit designed to wirelessly transmit its signal under full insertion in high-temperature (HT) harsh-environments (HE), such as those present in power plants and industrial settings (metallurgic, oil extraction, molding, and aerospace). The oscillator employed a silicon carbide (SiC) power transistor and HT passive components on a screen-printed alumina circuit board capable of operation beyond 300 °C. The HT oscillator circuit was powered solely by in-situ energy scavenging thermoelectric generator (TEG) modules using passive cooling, eliminating the need for an external power supply or active cooling. In addition, a silicon-based external booster circuit was used to achieve the required TEG voltage regulation to test the TEG-powered HT oscillator circuit. The TEG-powered oscillator circuit was tested inside a non-metallic furnace from room temperature to over 300 °C for transmission of a wireless signal, which was detected outside the furnace at 11 ft (3.4 m). Such a wireless transmitting system powered only by in-situ TEGs, with no requirement for external power or active cooling, is very attractive for flexible, mobile stand-alone control and sensor units targeted for operation in HT HE conditions found in power plants and industrial settings.

20 FOSSIL-FUELED POWER PLANTS↗