Results for “environmental characterization” — Page 18

DOE OSTI2025

Role of Mg:Al ratio and Pt promotion on mitigating the deactivation of Ni-based methane steam reforming catalysts

Ni-based catalysts for CH 4 steam reforming require fine-tuning to withstand deactivation under dynamic operation conditions relevant to emerging H 2 -driven technologies. This study investigates the impact of the Mg:Al ratio and Pt presence in catalyst composition on the activity and stability of industrially relevant Ni-based mono- and bimetallic catalysts during simulated daily start-up and shut-down cycles in various gas atmospheres. The evolution of the catalyst structure during extensive testing procedures was investigated in detail by complementary electron microscopy, in situ/operando XAS and XRD. The results obtained revealed that catalyst deactivation is promoted at high Mg:Al ratios and especially affects the monometallic catalysts. By converting CH 4 at lower temperatures, Pt regulates the extent of Ni oxidation and its incorporation into MgO lattice. Further prevention of catalyst deactivation was achieved by optimizing the reactor shut-down procedure to minimize the simultaneous exposure to high temperatures and H 2 O vapors. By flushing the reactor with N 2 only around the reaction extinction temperature, a fraction of Ni species is maintained in metallic state, which is beneficial for the long-term activity and reaction operation economy.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Compositional analysis of organosolv poplar lignin by using high-performance liquid chromatography/high-resolution multi-stage tandem mass spectrometry

Organosolv treatment is an efficient and environmentally friendly process to degrade lignin into small compounds. The capability of characterizing the individual compounds in the complex mixtures formed upon organosolv treatment is essential for the optimization of the further lignin conversion processes and for the rational genetic engineering of plants used to produce lignin in order to improve lignin properties. In this study, an organosolv poplar lignin sample was initially analyzed by high-resolution mass spectrometry coupled with negative-ion mode electrospray ionization ((-)ESI HRMS). Lignin monomers and dimers were found to constitute the majority of the compounds in the organosolv lignin sample. Larger lignin oligomers, such as trimers and tetramers, and some not lignin-related compounds, were also detected. A high-performance liquid chromatograph/linear quadrupole ion trap/orbitrap mass spectrometer capable of multi-stage high-resolution tandem mass spectrometry experiments (HRMS n ), equipped with an (-)ESI source (HPLC/(-)ESI HRMS n ), was employed to separate the unknown compounds in the organosolv mixture and to obtain structural information for the deprotonated compounds via collision-activated dissociation (CAD) HRMS n experiments. To improve the understanding of the CAD behavior of deprotonated lignin-related compounds, 16 deprotonated model compounds with different functionalities and linkage types were examined. This approach enabled the assignment of likely structures for several lignin monomers, dimers, trimers, and tetramers, and some not lignin-related compounds, most likely fatty acids. Based on the proposed structures, compounds in the organosolv lignin sample contain β-O-4, 5–5, β-5, and possibly also 4-O-5 linkages. Most compounds contain G- and S-monomeric units although a small amount of H-units were also detected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2026

Synthesizing land use and demographic change in Southeast Asia’s smaller urbanized areas from 2000–2015

The majority of the human population now reside in urban areas today. The United Nations estimates that nearly half of all urban dwellers currently live in cities smaller than 500 000 persons and the majority of future urban growth will take place in Asia and Africa, likely in these smaller urban areas, not mega cities. Thus, understanding the factors that influence urban demographic trajectories in small urban areas is critical to address sustainable and equitable policy initiatives related to food security, changing climate hazard exposure, and economic opportunities. Here we focus on Southeast Asia—a region historically characterized by lower urban population proportions, yet with a rapidly shifting dynamic demographic—to examine correlates of demographic change among smaller cities. We combine two open-source satellite-informed datasets: GHS urban center database (2015) and age-sex gridded data from WorldPop to calculate socio-demographic characteristics to model drivers of change in annualized urban population growth from 2000–2015 for 505 urbanized places. We find a general pattern of decreasing dependency ratios as city-size increases for most urban areas in Southeast Asia. Higher rates of growth and more variation is observed for smaller cities—those with fewer than 300 000 persons, the lowest population limit for UN data on urbanization. When examining covariates of urban population growth, we find significant statistical associations of population change in smaller urbanized areas with climatic, economic, and land cover/land use variables, but with country-specific variations. Characterizing a continuum of urban population development in the context of changing environmental, economic and climate conditions has been an important sustainable development and equity issue for decades, but newer analysis of city-level drivers allows for systematic inquiry thus moving beyond total population counts for policy-relevant insight.

Southeast Asia synthesis↗

DOE OSTI2025

Microbiome Comparison and Pathogen Identification for Three Migrating Passerines Captured During Spring Season in Jordan Using 16S rRNA Sequencing

Jordan is located on an important spot along the Mediterranean and Black Sea Flyway. Hundreds of migratory bird species have been identified stopping over in Jordan during spring and autumn migratory seasons. Compared to mammals and economically important birds, the microbiomes of wild bird species are severely understudied. Gut microbial composition is a valuable source of information that reflects food preferences, foraging behavior, and the risk of pathogen transmission to humans and other animals. In this study, we assessed the microbiome composition of three species of migrating passerines (willow warblers, lesser whitethroats, and common reed warblers) captured during the spring migration stopover in Jordan in 2023. A total of 59 fecal samples were selected evenly from the three species and subjected to 16S sequencing and microbiome analysis. Our objectives were to determine the diversity of bacteria in these three species, assess the amount of intra- and inter-specific variation, and detect pathogenic genera and species that could pose health risks to humans, domestic animals, and wildlife. Bacteria mainly belonged to the phyla Proteobacteria (62%), Actinobacteriota (18%), Firmicutes (13%), Cyanobacteria (5%), and Bacteroidota (1%). The results reveal that lesser whitethroats had the greatest variation in bacterial genus richness, Shannon diversity, and microbial composition compared to willow warblers and common reed warblers. The three bird species harbored several pathogenic genera and species, including Campylobacter, Enterococcus, Escherichia-Shigella, Mycoplasma, Rickettsia, Clostridium perfringens, and Vibrio cholerae. We suggest further investigation to understand the relationship between migratory behavior and their gut microbiome. We advocate for the use of advanced molecular techniques to characterize the pathogens found in migratory birds that might have public and environmental health impacts in addition to economic loss.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Seasonality regulates the structure and biogeochemical impact of ectomycorrhizal fungal communities across environmentally divergent neotropical dry forests

Abstract Ectomycorrhizal (ECM) symbioses support forest functioning globally, yet both the structure and function of ECM fungal communities in seasonally dry neotropical forests (SDTFs), known for extreme heterogeneity in vegetation and edaphic properties, remain under characterized. Here, we evaluated the relative influences of seasonal versus spatial variation in ECM fungal community structure in soils from four environmentally divergent SDTFs. We also assessed the importance of biotic and abiotic drivers of SDTF ECM fungal community structure at regional scales, as well as ECM impacts on soil carbon (C) and nitrogen (N) cycling. ECM fungal frequency, relative abundance and richness all increased in the wet season, but spatial rather than seasonal effects explained more variation in community composition. Across the four SDTFs investigated, differences in tree communities drove ECM fungal community turnover more than geographic distances, site abiotic conditions or soil chemistry. Although soil moisture and ECM tree basal area were stronger predictors of soil biogeochemistry, incorporating ECM fungal community composition and relative abundance added explanatory power to models of soil C and N cycling in the wet season. Synthesis : Our results highlight the importance of seasonality and plant community composition in shaping different aspects of SDTF ECM fungal community structure and diversity as well as the potential for both the plant and fungal components of ECM symbioses to impact soil functioning across heterogenous SDTFs. Furthermore, our findings suggest that alterations in SDTF plant community composition due to climate or land‐use change will have important consequences for ECM fungal diversity and associated effects on soil biogeochemical cycling.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2021

Escaping the fate of Sisyphus: assessing resistome hybridization baits for antimicrobial resistance gene capture

Finding, characterizing and monitoring reservoirs for antimicrobial resistance (AMR) is vital to protecting public health. Hybridization capture baits are an accurate, sensitive and cost-effective technique used to enrich and characterize DNA sequences of interest, including antimicrobial resistance genes (ARGs), in complex environmental samples. We demonstrate the continued utility of a set of 19 933 hybridization capture baits designed from the Comprehensive Antibiotic Resistance Database (CARD)v1.1.2 and Pathogenicity Island Database (PAIDB)v2.0, targeting 3565 unique nucleotide sequences that confer resistance. We demonstrate the efficiency of our bait set on a custom-made resistance mock community and complex environmental samples to increase the proportion of on-target reads as much as >200-fold. However, keeping pace with newly discovered ARGs poses a challenge when studying AMR, because novel ARGs are continually being identified and would not be included in bait sets designed prior to discovery. Here we provide imperative information on how our bait set performs against CARDv3.3.1, as well as a generalizable approach for deciding when and how to update hybridization capture bait sets. This research encapsulates the full life cycle of baits for hybridization capture of the resistome from design and validation (both in silico and in vitro) to utilization and forecasting updates and retirement.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2023

Proteomes reveal metabolic capabilities of Yarrowia lipolytica for biological upcycling of polyethylene into high-value chemicals

ABSTRACT Polyolefins derived from plastic wastes are recalcitrant for biological upcycling. However, chemical depolymerization of polyolefins can generate depolymerized plastic (DP) oil, comprising of a complex mixture of saturated, unsaturated, even, and odd hydrocarbons suitable for biological conversion. While DP oil contains a rich carbon and energy source, it is inhibitory to cells. Understanding and harnessing robust metabolic capabilities of microorganisms to upcycle the hydrocarbons in DP oil, both naturally and unnaturally occurring, into high-value chemicals are limited. Here, we discovered that an oleaginous yeast, Yarrowia lipolytica, undergoing short-term adaptation to DP oil robustly utilized a wide range of hydrocarbons for cell growth and production of citric acid and neutral lipids. When growing on hydrocarbons, Y. lipolytica partitioned into planktonic and oil-bound cells with each exhibiting distinct proteomes and amino acid distributions invested in establishing these proteomes. Significant proteome reallocation toward energy and lipid metabolism, belonging to 2 of the 23 Eukaryotic Orthologous Groups classes C and I, enabled robust growth of Y. lipolytica on hydrocarbons, with n-hexadecane as the preferential substrate. This investment was even higher for growth on DP oil where classes C and I were ranked one and two, respectively, and many associated proteins and pathways were expressed and upregulated including the hydrocarbon degradation pathway, Krebs cycle, glyoxylate shunt and, unexpectedly, propionate metabolism. However, a reduction in proteome allocation for protein biosynthesis, at the expense of the observed increase toward energy and lipid metabolisms, might have caused the inhibitory effect of DP oil on cell growth. IMPORTANCE Sustainable processes for biological upcycling of plastic wastes in a circular bioeconomy are needed to promote decarbonization and reduce environmental pollution due to increased plastic consumption, incineration, and landfill storage. Strain characterization and proteomic analysis revealed the robust metabolic capabilities of Yarrowia lipolytica to upcycle polyethylene into high-value chemicals. Significant proteome reallocation toward energy and lipid metabolisms was required for robust growth on hydrocarbons with n-hexadecane as the preferential substrate. However, an apparent over-investment in these same categories to utilize complex depolymerized plastic (DP) oil came at the expense of protein biosynthesis, limiting cell growth. Taken together, this study elucidates how Y. lipolytica activates its metabolism to utilize DP oil and establishes Y. lipolytica as a promising host for the upcycling of plastic wastes.

1-alkenes↗

DOE OSTI2020

Low-cost & Energy Dense Batteries for Transportation

The project sought to explore development of novel polymer separator materials and additives for Li-S and Li-ion batteries that would solve critical failure modes and performance bottlenecks for these chemistries. This technology presented significant advanced manufacturing challenges and opportunities in getting to scale, including materials synthesis scale-up, large-area polymer processing techniques, electrode formulation, and the development of coin and pouch cells for electrochemical energy storage. Specific accomplishments included synthesis of organic molecular and polymer materials designed to solve outstanding challenges in electrochemical cells. The primary focus of new materials design was aimed at improving longevity, power, cost reduction, and environmental sustainability of said electrochemical devices. The project also involved assembly and characterization of electrochemical devices with standard galvanostatic and potentiostatic techniques as well as electrochemical impedance spectroscopy.

25 ENERGY STORAGE↗

DOE OSTI2020

Performance Assessment of Portable Optical Particle Spectrometer (POPS)

Accurate representation of atmospheric aerosol properties is a long-standing problem in atmospheric research. Modern pilotless aerial systems provide a new platform for atmospheric in situ measurement. However, small airborne platforms require miniaturized instrumentation due to apparent size, power, and weight limitations. A Portable Optical Particle Spectrometer (POPS) is an emerged instrument to measure ambient aerosol size distribution with high time and size resolution, designed for deployment on a small unmanned aerial system (UAS) or tethered balloon system (TBS) platforms. This study evaluates the performance of a POPS with an upgraded laser heater and additional temperature sensors in the aerosol pathway. POPS maintains its performance under different environmental conditions as long as the laser temperature remains above 25 °C and the aerosol flow temperature inside the optical chamber is 15 °C higher than the ambient temperature. The comparison between POPS and an Ultra-High Sensitivity Aerosol Spectrometer (UHSAS) suggests that the coincidence error is less than 25% when the number concentration is less than 4000 cm –3 . The size distributions measured by both of them remained unaffected up to 15,000 cm –3 . While both instruments’ sizing accuracy is affected by the aerosol chemical composition and morphology, the influence is more profound on the POPS.

47 OTHER INSTRUMENTATION↗

DOE OSTI2021

Recent advances in nano-scale spatial resolution x-ray microscopy instrumentation at NSLS-II

X-ray microscopy is an invaluable and powerful characterization tool applied in many scientific fields, such as materials science, biology, environmental science, and energy research. In recent years it has been driven by rapid developments of novel technologies and systems resulting in imaging experiments elucidating structural inhomogeneities and chemical reactions at the nanometer scale. To obtain high spatial resolution comprehensive chemical and structural information, an X-ray microscope must be equipped with adequate capabilities and allow for simultaneous acquisition of multiple datasets. In recent years, a number of X-ray microscopes have been designed, constructed, and commissioned at NSLS-II. Here we provide an overview of the microscopy instrumentation development program at NSLS-II and specifically focus on the multilayer Laue lens-based hard X-ray nanoprobe optimized for ~10 nm spatial resolution imaging, its current status, and future upgrades along with recently constructed Kirkpatrick-Baez based scanning microscope designed for ~100 nm spatial resolution experiments.

36 MATERIALS SCIENCE↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel

Chemical Interaction of Palladium in Uranium Oxycarbide Nuclear Fuel Kernel Jana Howard1,3, Guang Yang3, Haiyan Zhao1*, Patrick Warren4, Tiankai Yao3, Steven Cavazos4 Elizabeth Sooby Wood4*, Ching-heng Shiau2 1 University of Idaho, Environmental Science, Idaho Falls, Idaho, USA 2 Boise State University, Microscopy and Characterization Suite, Idaho Falls, Idaho, USA 3 Idaho National Laboratory, Idaho Falls, Idaho, USA 4 University of Texas San Antonio, Department of Physics and Astronomy, San Antonio, Texas, USA *Corresponding author: haiyanz@uidaho.edu; elizabeth.soobywood@utsa.edu Tri-structural Isotropic (TRISO) particle fuel is the preferred choice for the newest and next-generation high-temperature nuclear reactors due to its robust construction [1]. The fuel design effectively contains fission products inside the particle at extremely high temperatures [2]. However, the effect of transition metal fission products on fuel performance and structural integrity remains largely unknown, creating uncertainties in predicting fuel performance and potential failure mechanisms [2]. For example, palladium (Pd) has a strong tendency to form intermetallic phases with uranium (U). These new phases tend to be hard and brittle which could lead to fracture of fuel kernel during irradiation [3,4]. Pd is not normally produced in high concentrations in normal fission reactions however, driving the production of Pd into the locality of a Uranium Oxycarbide (UCO) nuclear fuel provides an opportunity to closely observe the diffusion and chemical interactions. This study focuses on detailed transmission electron microscopy characterization of the intermetallic phases formed by the interaction between a UCO kernel and a Pd bar after annealing at 1100 °C for 100 hours. Figure 1 provides an overview of the UCO kernel in contact with the Pd bar. The UCO-Pd sample surface was examined using a Focused Ion Beam (FIB) Quanta 3D FEG FEI in VCD detector mode at 10kV, 83pA to reveal surface features. Several key surface features in the interaction region were observed including: (1) a small area with dendritic microstructure, (2) color contrast near the UCO kernel and Pd boundary, and (3) darker and lighter regions throughout the sample surface. To analyze diffusion behavior, FIB was used to prepare lamellae from five different areas of the UCO-Pd sample, as well as one for the as-received sample. These lamellae were examined using a Scanning Transmission Electron Microscope ThermoFisher Spectra 300 (STEM-Spectra). Energy Dispersive Spectroscopy results confirmed the diffusion between the UCO fuel and Pd bar. Figure 2 shows the identified phases of UC, UO2, and Pd dispersed throughout the interaction region. It was also found that the Pd concentration decreases as the radial distance from the UCO-Pd interface increases. The Pd concentration was 36.93% atomic fraction 11µm from the interaction region then decreased to 7.51% atomic fraction at 257 µm away from the interaction region. Figure 3 shows how concentrations of U and Pd vary across the interaction zone, highlighting the extent of diffusion. This study confirms that Pd interacts with surrounding material to form U-Pd phase and diffusion zones. These diffusion zones vary in composition depending on its radial distance from the point of contact with the Pd bar. These findings contribute to a deeper understanding of the fission product behavior in high temperature nuclear fuels, aiding in the prediction and mitigation of potential fuel degradation mechanisms. A B C Fig. 1. SEM micrographs of UCO fuel kernel in contact with solid Pd bar and the lift out locations. Figure 1A shows UCO fuel kernel in contact with solid Pd bar. Figure 1B shows a higher magnification image of the UCO fuel-Pd interaction zone. Figure 1C shows lift out sites for the lamellae. A B C Fig 2. EDS maps reveal the distribution of U, O, and Pd in location 3. Figure 2A shows the distribution of uranium. Figure 2B shows the distribution of oxygen. Figure 2C shows the distribution of palladium. A B C Fig 3. Palladium and uranium concentration across interaction zone in location 2. Figure 3A shows EDS map of lift out number 2. Figure 3B shows a zoomed in EDS map taken from the interaction zone. Figure 3C shows a line graph of uranium and palladium concentrations across the interaction zone. References: 1. B.E. Wells, N.R. Phillips, K.J. Geelhood. Pacific West Laboratory. (2021). TRISO Fuel: Properties and Failure Modes. https://www.nrc.gov/docs/ML2117/ML21175A152.pdf (Accessed January 16, 2025). 2. American Nuclear Society. TRISO Fuel Development Progresses in INL, ORNL. https://www.gen-4.org/gif/upload/docs/application/pdf/2014-03/nov13nn_fuel_reprint.pdf (Accessed January 16, 2025) 3. Clark R.A., M.A. Con

36 - MATERIALS SCIENCE↗

DOE OSTI2025

Studying Aerosol, Clouds, and Air Quality in the Coastal Urban Environment of Southeastern Texas

A multi-agency succession of field campaigns was conducted in southeastern Texas during July 2021 through October 2022 to study the complex interactions of aerosols, clouds and air pollution in the coastal urban environment. As part of the Tracking Aerosol Convection interactions Experiment (TRACER), the TRACER- Air Quality (TAQ) campaign the Experiment of Sea Breeze Convection, Aerosols, Precipitation and Environment (ESCAPE) and the Convective Cloud Urban Boundary Layer Experiment (CUBE), a combination of ground-based supersites and mobile laboratories, shipborne measurements and aircraft-based instrumentation were deployed. These diverse platforms collected high-resolution data to characterize the aerosol microphysics and chemistry, cloud and precipitation micro- and macro-physical properties, environmental thermodynamics and air quality-relevant constituents that are being used in follow-on analysis and modeling activities. We present the overall deployment setups, a summary of the campaign conditions and a sampling of early research results related to: (a) aerosol precursors in the urban environment, (b) influences of local meteorology on air pollution, (c) detailed observations of the sea breeze circulation, (d) retrieved supersaturation in convective updrafts, (e) characterizing the convective updraft lifecycle, (f) variability in lightning characteristics of convective storms and (g) urban influences on surface energy fluxes. The work concludes with discussion of future research activities highlighted by the TRACER model-intercomparison project to explore the representation of aerosol-convective interactions in high-resolution simulations.

54 ENVIRONMENTAL SCIENCES↗

DOE OSTI2024

Abstract for CRADA between National Energy Technology Laboratory and ClearSign Technologies Corporation

The National Energy Technology Laboratory (NETL) and ClearSign Technologies Corporation (Participant) will collaborate in the development of a preliminary LCA for the scaling of a hydrogen burner product currently in proof of concept and primarily developed for chemicals processing at refineries. The current combustion product has been tested at 80% hydrogen content (20% natural gas) and maintains the NOx 97% improvement vs incumbent technologies, yet the GHG emissions of the product and use case in refining to chemicals processing would be the focus of this preliminary LCA. The Participant has noted areas where they expect environmental improvements relative to alternatives, but these improvements have not been quantified to date. The collaboration will facilitate characterizing the emissions improvement comparative to some selected incumbent technologies during the deployment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Characterization of Senecavirus A Isolates Collected From the Environment of U.S. Sow Slaughter Plants

Vesicular disease caused by Senecavirus A (SVA) is clinically indistinguishable from foot-and-mouth disease (FMD) and other vesicular diseases of swine. When a vesicle is observed in FMD-free countries, a costly and time-consuming foreign animal disease investigation (FADI) is performed to rule out FMD. Recently, there has been an increase in the number of FADIs and SVA positive samples at slaughter plants in the U.S. The objectives of this investigation were to: (1) describe the environmental burden of SVA in sow slaughter plants; (2) determine whether there was a correlation between PCR diagnostics, virus isolation (VI), and swine bioassay results; and (3) phylogenetically characterize the genetic diversity of contemporary SVA isolates. Environmental swabs were collected from three sow slaughter plants (Plants 1-3) and one market-weight slaughter plant (Plant 4) between June to December 2020. Of the 426 samples taken from Plants 1-3, 304 samples were PCR positive and 107 were VI positive. There was no detection of SVA by PCR or VI at Plant 4. SVA positive samples were most frequently found in the summer (78.3% June-September, vs. 59.4% October-December), with a peak at 85% in August. Eighteen PCR positive environmental samples with a range of C t values were selected for a swine bioassay: a single sample infected piglets ( n = 2). A random subset of the PCR positive samples was sequenced; and phylogenetic analysis demonstrated co-circulation and divergence of two genetically distinct groups of SVA. These data demonstrate that SVA was frequently found in the environment of sow slaughter plants, but environmental persistence and diagnostic detection was not indicative of whether a sampled was infectious to swine. Consequently, a more detailed understanding of the epidemiology of SVA and its environmental persistence in the marketing chain is necessary to reduce the number of FADIs and aide in the development of control measures to reduce the spread of SVA.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Feasibility of source-free DAS logging for next-generation borehole imaging

Characterizing and monitoring geologic formations around a borehole are crucial for energy and environmental applications. However, conventional wireline sonic logging usually cannot be used in high-temperature environments nor is the tool feasible for long-term monitoring. We introduce and evaluate the feasibility of a source-free distributed-acoustic-sensing (DAS) logging method based on borehole DAS ambient noise. Our new logging method provides a next-generation borehole imaging tool. The tool is source free because it uses ever-present ambient noises as sources and does not need a borehole sonic source that cannot be easily re-inserted into a borehole after well completion for time-lapse monitoring. The receivers of our source-free DAS logging tool are fiber optic cables cemented behind casing, enabling logging in harsh, high-temperature environments, and eliminating the receiver repeatability issue of conventional wireline sonic logging for time-lapse monitoring. We analyze a borehole DAS ambient noise dataset to obtain root-mean-squares (RMS) amplitudes and use these amplitudes to infer subsurface elastic properties. We find that the ambient noise RMS amplitudes correlate well with anomalies in conventional logging data. The source-free DAS logging tool can advance our ability to characterize and monitor subsurface geologic formations in an efficient and cost-effective manner, particularly in high-temperature environments such as geothermal reservoirs. Further validation of the source-free DAS logging method using other borehole DAS ambient noise data would enable the new logging tool for wider applications.

58 GEOSCIENCES↗

DOE OSTI2025

Southwest Regional Partnership on Carbon Sequestration: Phase III (Final Scientific/Technical Report)

The Southwest Regional Partnership on Carbon Sequestration (SWP) is one of 7 regional partnerships formed in 2003 under the U.S. Department of Energy’s (DOE) Regional Carbon Sequestration Partnerships (RCSPs) initiative. The overall purpose of the initiative was to help determine and implement the technology, infrastructure, and regulations most appropriate to promote carbon storage in different regions of the country. Covering Arizona, Colorado, New Mexico, Oklahoma, Utah, and parts of Texas, Wyoming, and Kansas, the SWP evaluated regional carbon storage and utilization potential and focused on technologies and sites that could complement the region’s strong position in energy production. The project progressed through three phases: • Phase I (2003–2005): Characterized regional geologic formations and CO 2 sources, assessed sequestration potential, and identified pilot test sites. • Phase II (2005–2013): Conducted small-scale field tests to validate sequestration methods, including geologic and terrestrial projects. • Phase III (2008–2022): Demonstrated large-scale CO 2 injection at a commercial oil field to test monitoring, verification, and long-term storage strategies. This report covers Phase III. The final project site, the Farnsworth Unit (FWU) in Texas, provided real-world testing of reservoir characterization, monitoring, and risk evaluation tools and processes that could be used in any commercial scale carbon capture, utilization, and storage (CCUS) project. Extensive data collection and analysis helped refine best practices for reservoir characterization, injection monitoring, and storage verification. The SWP contributed to national databases, DOE best practice manuals, and regional geological assessments to support future sequestration efforts. Key lessons learned include the importance of robust data management, strategic site selection, regulatory navigation, and effective industry collaboration. The project’s findings will inform ongoing and future carbon storage initiatives. Task 1 (Regional Characterization) • The SWP continued to participate in national outreach efforts and NATCARB. • The SWP evaluated multiple potential sites before selecting the FWU as the primary field test location. Task 2 (Public Outreach and Education) • The SWP contributed to national databases, DOE best practice manuals, and regional geological assessments to support future sequestration efforts. Task 3 (Permitting and Regulatory Compliance) • The SWP ensured compliance with federal and state regulations, including National Environmental Policy Act (NEPA) requirements. • The SWP obtained all necessary permits for drilling, injection, and monitoring activities. Task 4 (Site Characterization and Planning) • The SWP developed work plans for four key activities: characterization, simulation, monitoring and verification, and risk evaluation. • The SWP collected and synthesized legacy data from multiple sources to build initial static geological models and dynamic reservoir models demonstrating project feasibility. • The SWP conducted an initial risk evaluation and developed mitigation plans. Task 5 (Field Operations and Data Collection) • The SWP drilled, logged, and cored three characterization wells to gather critical subsurface data. • The SWP conducted multiple geophysical surveys, including 3D seismic, crosswell seismic, and vertical seismic profiling, to improve reservoir characterization. Task 6 (Monitoring and Verification) • The SWP performed extensive geological characterization using data from characterization wells and seismic surveys. • The SWP established a surface monitoring network to track CO 2 flux in soil gas, groundwater chemistry, and near-surface atmospheric CO 2 levels. • The SWP built and refined reservoir models to study the effects of relative permeability on simulation behavior and improve calibration with experimental data. Task 7 (Risk Assessment and Model Refinement) • The SWP conducted multiple studies to evaluate reservoir integrity, predict CO 2 plume behavior and improve predictive modeling capabilities. • The SWP refined geological models and used them to enhance the accuracy of simulation models. • The SWP continued quantitative risk assessment of top-ranked risks and strengthened the link between qualitative and quantitative risk methodologies.

02 PETROLEUM↗

DOE OSTI2020

Rare earth metals from secondary sources: Review of potential supply from waste and byproducts

Current concerns about lack of diversity in supply of critical metals have spurred research into utilizing domestic sources, particularly from waste streams. Sustainability strategies like urban mining, industrial symbiosis, and the circular economy suggest avenues to realize new supplies of critical metals. In this work we explore the resource and economic potential for extracting rare earth elements (REEs) from industry byproducts (e.g. coal combustion products, red mud) and secondary sources (e.g. waste electronics and light bulbs). Combining materials flow analysis and characterization data, we find that while REE concentrations in waste and byproduct streams are mostly much lower than current REE ores, some secondary sources are richer than ores in high value REEs such as scandium. The quantities of REEs contained in secondary sources could meet current global demand even with low extraction yield rates. Phosphogypsum, coal ash and red mud from aluminum production stand out as promising candidates for recovery due to high concentrations of valuable REEs and sufficient quantities to potentially meet demand. Processes to extract REEs from secondary sources are under development, it is not clear yet which will be profitable at scale and which can be achieved at least environmental impact. This work provides high level guidance on the potential of secondary sources by characterizing quality (concentrations of different rare earths) and quantity (mass of rare earths in global scale wastes and byproducts). This significant first step helps clarify directions for policy and research and development investments.

42 ENGINEERING↗