Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “elastic”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Characteristic Elastic Systems of Time-Limited Optimal Maneuvers

Optimizing an elastic system and its active control is discussed. Maneuvers from an initial state to a final state in a finite time interval are considered. An active generalized control force that accomplishes the desired maneuver of a prespecified system is optimal if it minimizes a given quadratic cost function. By also varying a set of design parameters, the elastic system can be determined so as to further minimize the cost function. Here, the elastic system that minimizes the actual control cost is compared with the system that minimizes the ratio of actual cost to the cost of optimally maneuvering a rigid system of the same inertial properties. It is shown that an elastic system corresponding to an extremum of the ratio is actually a characteristic of the time-limited maneuver. Because both the spatial domain and the time interval are fixed, a characteristic elastic system is tuned to the specified temporal boundary conditions. The implication for rest-to-rest, spinup, and spin reversal maneuvers of spacecraft is that the optimal control for a characteristic elastic spacecraft is identical to the optimal control for the same spacecraft as if it were rigid.

Hale, A. L.↗

Elastic electron scattering cross sections for molecular hydrogen

Using an electron-beam - molecular-beam apparatus and employing the relative flow technique, ratios of the differential elastic scattering cross sections (DCSs of H2 to He were measured at incident electron energies of 15-100 eV and over the angular range of 10-125 degrees. From these ratios, the absolute elastic DCSs for H2 were determined by normalization to accurate, available elastic DCSs of He. Since pure rotational structure was not resolved in this work, the DCSs reported are the sum of elastic and rotational excitations of H2 at room temperature. The reliability of the relative flow normalization to He was checked at each energy and angle by performing similar elastic DCS measurements on Ne (for which the cross sections are known). The resulting absolute Ne DCSs were found to be in good agreement (within 10 percent with the Ne elastic DCSs measured previously (Register and Trajmar, 1984). From the DCSs, integral and momentumtransfer cross sections were calculated. The present results are compared with other recent measurements.

Khakoo, M. A.↗

Flexural models of trench/outer rise topography of coronae on Venus with axisymmetric spherical shell elastic plates

Magellan altimetry has revealed that many coronae on Venus have trenches or moats around their peripheries and rises outboard of the trenches. This trench/outer rise topographic signature is generally associated with the tectonic annulus of the corona. Sandwell and Schubert have interpreted the trench/outer rise topography and the associated tectonic annulus around coronae to be the result of elastic bending of the Venus lithosphere (though the tectonic structures are consequences of inelastic deformation of the lithosphere). They used two-dimensional elastic plate flexure theory to fit topographic profiles across a number of large coronae and inferred elastic lithosphere thicknesses between about 15 and 40 km, similar to inferred values of elastic thickness for the Earth's lithosphere at subduction zones around the Pacific Ocean. Here, we report the results of using axisymmetric elastic flexure theory for the deformation of thin spherical shell plates to interpret the trench/outer rise topography of the large coronae modeled by Sandwell and Schubert and of coronae as small as 250 km in diameter. In the case of a corona only a few hundred kilometers in diameter, the model accounts for the small planform radius of the moat and the nonradial orientation of altimetric traces across the corona. By fitting the flexural topography of coronae we determine the elastic thickness and loading necessary to account for the observed flexure. We calculate the associated bending moment and determine whether the corona interior topographic load can provide the required moment. We also calculate surface stresses and compare the stress distribution with the location of annular tectonic features.

Moore, W.↗

Evaluation of a Hybrid Elastic EVA Glove

The hybrid elastic design is based upon an American Society for Engineering Education (ASEE) glove designed by at the Space Systems Laboratory (SSL) in 1985. This design uses an elastic restraint layer instead of convolute joints to achieve greater dexterity and mobility during EVA (extravehicular activity). Two pilot studies and a main study were conducted using the hybrid elastic glove and 4000-series EMU (extravehicular activity unit) glove. Data on dexterity performance, joint range of motion, grip strength and perceived exertion was assessed for the EMU and hybrid elastic gloves with correlations to a barehanded condition. During this study, 30 test subjects performed multiple test sessions using a hybrid elastic glove and a 4000- series shuttle glove in a 4.3psid pressure environment. Test results to date indicate that the hybrid elastic glove performance is approximately similar to the performance of the 4000-series glove.

Korona, F. Adam↗

Apparent elastic modulus and hysteresis of skeletal muscle cells throughout differentiation

The effect of differentiation on the transverse mechanical properties of mammalian myocytes was determined by using atomic force microscopy. The apparent elastic modulus increased from 11.5 +/- 1.3 kPa for undifferentiated myoblasts to 45.3 +/- 4.0 kPa after 8 days of differentiation (P < 0.05). The relative contribution of viscosity, as determined from the normalized hysteresis area, ranged from 0.13 +/- 0.02 to 0.21 +/- 0.03 and did not change throughout differentiation. Myosin expression correlated with the apparent elastic modulus, but neither myosin nor beta-tubulin were associated with hysteresis. Microtubules did not affect mechanical properties because treatment with colchicine did not alter the apparent elastic modulus or hysteresis. Treatment with cytochalasin D or 2,3-butanedione 2-monoxime led to a significant reduction in the apparent elastic modulus but no change in hysteresis. In summary, skeletal muscle cells exhibited viscoelastic behavior that changed during differentiation, yielding an increase in the transverse elastic modulus. Major contributors to changes in the transverse elastic modulus during differentiation were actin and myosin.

NASA Discipline Musculoskeletal↗

Single-Crystal Elastic Constants of Yttria (Y2O3) Measured to High Temperatures

Yttria, or yttrium sesquioxide (Y2O3), has been considered for use in nuclear applications and has gained interest relatively recently for use in infrared optics. Single crystals of yttria have been grown successfully at the NASA Glenn Research Center using a laser-heated float zone technique in a fiber and rod. Such samples allow measurement of the single-crystal elastic properties, and these measurements provide useful property data for the design of components using single crystals. They also yield information as to what degree the elastic properties of yttria ceramics are a result of the intrinsic properties of the yttria crystal in comparison to characteristics that may depend on processing, such as microstructure and intergranular phases, which are common in sintered yttria. The single-crystal elastic moduli are valuable for designing such optical components. In particular, the temperature derivatives of elastic moduli allow the dimensional changes due to heating under physical constraints, as well as acoustic excitation, to be determined. The single-crystal elastic moduli of yttria were measured by Brillouin spectroscopy up to 1200 C. The room-temperature values obtained were C(sub 11) = 223.6 + 0.6 GPa, C(sub 44) = 74.6 + 0.5 GPa, and C(sub 12) = 112.4 + 1.0 GPa. The resulting bulk and (Voigt-Reuss-Hill) shear moduli were K = 149.5 + 1.0 GPa and G(sub VRH) = 66.3 + 0.8 GPa, respectively. Linear least-squares regressions to the variation of bulk and shear moduli with temperature resulted in derivatives of dK/dT = -17 + 2 MPa/C and dG(sub VRH)/dT = -8 + 2 MPa/ C. Elastic anisotropy was found to remain essentially constant over the temperature range studied.

Sayir, Ali↗

Elastic-Plastic Fracture Mechanics Analysis of Critical Flaw Size in ARES I-X Flange-to-Skin Welds

NASA's Ares 1 Upper Stage Simulator (USS) is being fabricated from welded A516 steel. In order to insure the structural integrity of these welds it is of interest to calculate the critical initial flaw size (CIFS) to establish rational inspection requirements. The CIFS is in turn dependent on the critical final flaw size (CFS), as well as fatigue flaw growth resulting from transportation, handling and service-induced loading. These calculations were made using linear elastic fracture mechanics (LEFM), which are thought to be conservative because they are based on a lower bound, so called elastic, fracture toughness determined from tests that displayed significant plasticity. Nevertheless, there was still concern that the yield magnitude stresses generated in the flange-to-skin weld by the combination of axial stresses due to axial forces, fit-up stresses, and weld residual stresses, could give rise to significant flaw-tip plasticity, which might render the LEFM results to be non-conservative. The objective of the present study was to employ Elastic Plastic Fracture Mechanics (EPFM) to determine CFS values, and then compare these values to CFS values evaluated using LEFM. CFS values were calculated for twelve cases involving surface and embedded flaws, EPFM analyses with and without plastic shakedown of the stresses, LEFM analyses, and various welding residual stress distributions. For the cases examined, the computed CFS values based on elastic analyses were the smallest in all instances where the failures were predicted to be controlled by the fracture toughness. However, in certain cases, the CFS values predicted by the elastic-plastic analyses were smaller than those predicted by the elastic analyses; in these cases the failure criteria were determined by a breakdown in stress intensity factor validity limits for deep flaws (a greater than 0.90t), rather than by the fracture toughness. Plastic relaxation of stresses accompanying shakedown always increases the calculated CFS values compared to the CFS values determined without shakedown. Thus, it is conservative to ignore shakedown effects.

Chell, G. Graham↗

Invariant surface elastic properties in FCC metals and their correlation to bulk properties revealed by machine learning methods

In this work, we present a combination of machine-learned models that predicts the surface elastic properties of general free surfaces in face-centered cubic (FCC) metals. These models are built by combining a semi-analytical method based on atomistic simulations to calculate surface properties with the artificial neural network (ANN) method or the boosted regression tree (BRT) method. The latter is also used to link bulk properties and surface orientation to surface properties. The surface elastic properties are represented by their invariants considering plane elasticity within a polar method. The resulting models are shown to accurately predict the surface elastic properties of seven pure FCC metals (Cu, Ni, Ag, Au, Al, Pd, Pt). The BRT model reveals the correlations between bulk and corresponding surface properties in terms of invariants, which can be used to guide the design of complex nano-sized particles, wires and films. Finally, by expressing the surface excess energy density as a function of surface elastic invariants, fast predictions of surface energy as a function of in-plane deformations can be made from these model constructs.

36 MATERIALS SCIENCE↗

An Elastic-Plastic Damage Model for Long-Fiber Thermoplastics

This article proposes an elastic-plastic damage model that combines micromechanical modeling with continuum damage mechanics to predict the stress-strain response of injection-molded long-fiber thermoplastics. The model accounts for distributions of orientation and length of elastic fibers embedded in a thermoplastic matrix whose behavior is elastic-plastic and damageable. The elastic-plastic damage behavior of the matrix is described by the modified Ramberg-Osgood relation and the three-dimensional damage model in deformation assuming isotropic hardening. Fiber/matrix debonding is accounted for using a parameter that governs the fiber/matrix interface compliance. A linear relationship between this parameter and the matrix damage variable is assumed. First, the elastic-plastic damage behavior of the reference aligned-fiber composite containing the same fiber volume fraction and length distribution as the actual composite is computed using an incremental Eshelby-Mori-Tanaka mean field approach. The incremental response of the latter is then obtained from the solution for the aligned-fiber composite by averaging over all fiber orientations. The model is validated against the experimental stress-strain results obtained for long-glass-fiber/polypropylene specimens.

36 MATERIALS SCIENCE↗

Elastic Properties in Tension and Shear of High Strength Nonferrous Metals and Stainless Steel - Effect of Previous Deformation and Heat Treatment

A resume is given of an investigation of the influence of plastic deformation and of annealing temperature on the tensile and shear elastic properties of high strength nonferrous metals and stainless steels in the form of rods and tubes. The data were obtained from earlier technical reports and notes, and from unpublished work in this investigation. There are also included data obtained from published and unpublished work performed on an independent investigation. The rod materials, namely, nickel, monel, inconel, copper, 13:2 Cr-Ni steel, and 18:8 Cr-Ni steel, were tested in tension; 18:8 Cr-Ni steel tubes were tested in shear, and nickel, monel, aluminum-monel, and Inconel tubes were tested in both tension and shear. There are first described experiments on the relationship between hysteresis and creep, as obtained with repeated cyclic stressing of annealed stainless steel specimens over a constant load range. These tests, which preceded the measurements of elastic properties, assisted in devising the loading time schedule used in such measurements. From corrected stress-set curves are derived the five proof stresses used as indices of elastic or yield strength. From corrected stress-strain curves are derived the secant modulus and its variation with stress. The relationship between the forms of the stress-set and stress-strain curves and the values of the properties derived is discussed. Curves of variation of proof stress and modulus with prior extension, as obtained with single rod specimens, consist in wavelike basic curves with superposed oscillations due to differences of rest interval and extension spacing; the effects of these differences are studied. Oscillations of proof stress and modulus are generally opposite in manner. The use of a series of tubular specimens corresponding to different amounts of prior extension of cold reduction gave curves almost devoid of oscillation since the effects of variation of rest interval and extension spacing were removed. Comparison is also obtained between the variation of the several properties, as measured in tension and in shear. The rise of proof stress with extension is studied, and the work-hardening rates of the various metals evaluated. The ratio between the tensile and shear proof stresses for the various annealed and cold-worked tubular metals is likewise calculated. The influence of annealing or tempering temperature on the proof stresses and moduli for the cold-worked metals and for air-hardened 13:2 Cr-Ni steel is investigated. An improvement of elastic strength generally is obtained, without important loss of yield strength, by annealing at suitable temperature. The variation of the proof stress and modulus of elasticity with plastic deformation or annealing temperature is explained in terms of the relative dominance of three important factors: namely, (a) internal stress, (b) lattice-expansion or work-hardening, and (c) crystal reorientation. Effective values of Poisson's ratio were computed from tensile and shear moduli obtained on tubular specimens. The variation of Poisson's ratio with plastic deformation and annealing temperature is explained in terms of the degree of anisotropy produced by changes of (a) internal stress and (b) crystal orientation.

METALS - ELASTICITY↗

The Elastic Constants for Wrought Aluminum Alloys

There are several constants which have been devised as numerical representations of the behavior of metals under the action of loadings which stress the metal within the range of elastic action. Some of these constants, such as Young's modulus of elasticity in tension and compression, shearing modulus of elasticity, and Poisson's ratio, are regularly used in engineering calculations. Precise tests and experience indicate that these elastic constants are practically unaffected by many of the factors which influence the other mechanical properties of materials and that a few careful determinations under properly controlled conditions are more useful and reliable than many determinations made under less favorable conditions. It is the purpose of this paper to outline the methods employed by the Aluminum Research Laboratories for the determination of some of these elastic constants, to list the values that have been determined for some of the wrought aluminum alloys, and to indicate the variations in the values that may be expected for some of the commercial products of these alloys.

ALUMINUM ALLOYS, WROUGHT-ELASTICITY↗

Structural, Elastic, Thermodynamic, Electronic, and Magnetic Investigations of Full-Heusler Compound Ag{sub 2}CeAl: FP-LAPW Method

Structural, elastic, thermodynamic, electronic, and magnetic properties of the full-Heusler compound Ag{sub 2}CeAl were determined using generalized gradient approximation with exchange-correlation functional GGA (PBEsol) with spin-orbit coupling (SOC) correction. The elastic modulus and their pressure dependence are calculated. From the elastic parameter behavior, it is inferred that this compound is elastically stable and ductile in nature. Through the quasi-harmonic Debye model, in which the phononic effect is considered the effect of pressure P (0 to 50) and temperature T (0 to 1000) on the lattice constant, the elastic parameters, bulk modulus B, heat capacity and thermal expansion α, internal energy U, entropy S, Debye temperature 𝜃{sub D}, Helmholtz free energy A, and Gibbs free energy G are investigated. The thermodynamic properties show that the compound Ag{sub 2}CeAl is a heavy fermion material. The density of state (DOS), magnetic momentum, and band structure are computed, to investigate the magnetic and metallic characteristics. The calculated polarization of the compound is 77.34%. The obtained results are the first predictions of the physical properties for the rare-earth-based (Ce) full-Heusler Ag{sub 2}CeAl.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Efficient machine-learning model for fast assessment of elastic properties of high-entropy alloys

We combined descriptor-based analytical models for stiffness-matrix and elastic-moduli with mean-field methods to accelerate assessment of technologically useful properties of high-entropy alloys, such as strength and ductility. Model training for elastic properties uses Sure-Independence Screening (SIS) and Sparsifying Operator (SO) method yielding an optimal analytical model, constructed with meaningful atomic features to predict target properties. Computationally inexpensive analytical descriptors were trained using a database of elastic properties determined from density functional theory for binary and ternary subsets of Nb-Mo-Ta-W-V refractory alloys. The optimal Elastic-SISSO models, extracted from an exponentially large feature space, give an extremely accurate prediction of target properties, similar to or better than other models, with some verified from existing experiments. Here we also show that electronegativity variance and elastic-moduli can directly predict trends in ductility and yield strength of refractory HEAs, and reveals promising alloy concentration regions.

36 MATERIALS SCIENCE↗

Field Dislocation Mechanics for heterogeneous elastic materials: A numerical spectral approach

Spectral methods using Fast Fourier Transform (FFT) algorithms have recently seen a surge in interest in the mechanics of materials community. The present work addresses the critical question of determining accurate local mechanical fields using FFT methods without artificial fluctuations arising from materials and defects induced discontinuities. Precisely, this work introduces a numerical approach based on intrinsic discrete Fourier transforms for the simultaneous treatment of material discontinuities arising from the presence of dislocations and from elastic stiffness heterogeneities. To this end, the elasto-static equations of the field dislocation mechanics theory for periodic heterogeneous materials are numerically solved with FFT in the case of dislocations in proximity of inclusions of varying stiffness. An optimal intrinsic discrete Fourier transform method is sought based on two distinct schemes. A centered finite difference scheme for differential rules are used for numerically solving the Poisson-type equation in the Fourier space, while centered finite differences on a rotated grid is chosen for the computation of the modified Fourier–Green’s operator associated with the Lippmann–Schwinger-type equation. By comparing different methods with analytical solutions for an edge dislocation in a composite material, it is found that the present spectral method is accurate, devoid of any numerical oscillation, and efficient even for an infinite phase elastic contrast like a hole embedded in a matrix containing a dislocation. The present FFT method is then used to simulate physical cases such as the elastic fields of dislocation dipoles located near the matrix/inclusion interface in a 2D composite material and the ones due to dislocation loop distributions surrounding cubic inclusions in 3D composite material. In these configurations, the spectral method allows investigating accurately the elastic interactions and image stresses due to dislocation fields in the presence of elastic inhomogeneities.

36 MATERIALS SCIENCE↗

The effect of elastic anisotropy on the symmetry selection of irradiation-induced void superlattices in cubic metals

We report self-organized microstructures and patterns have been widely observed in non-equilibrium physical systems. In particular, irradiation in metals creates far-from-equilibrium environments, in which the competing dynamics of defect production and annihilation can lead to unique self-organized superlattice structures, e.g., void and gas bubble superlattices. From a physical point of view, the superlattice structures are dictated by the intrinsic symmetry breaking in the metals, i.e., anisotropy caused by the breaking of continuous rotational symmetry. In the literature, two distinctive anisotropies, elastic anisotropy and diffusion anisotropy of interstitials, have been proposed to be the origins of superlattice formation. However, it is still unclear which anisotropy dominates the symmetry selection of superlattice structures. In this paper, we study elastic anisotropy and its effect on the symmetry of void superlattices. By using theoretical analyses and phase field simulations, we show that elastic anisotropy in cubic metals can lead to either face-centered cubic or simple cubic superlattices depending on the Zener anisotropy ratio. The superlattices formed under this elastic anisotropy mechanism must form under the influence of spinodal decomposition, as the mechanism requires perturbations in the vacancy concentration field to develop into spatially-static concentration waves. We compare to existing work on symmetry selection in superlattices via diffusion anisotropy and to experimental observations, and we suggest that concentration wave development under the influence of elastic anisotropy is not the mechanism for symmetry selection during the formation of irradiation-induced void superlattices, but that diffusion anisotropy could be the dominant mechanism.

36 MATERIALS SCIENCE↗

The Water-Fe-Pressure dependent single-crystal elastic properties of wadsleyite: Implications for the seismic anisotropy in the upper Mantle Transition Zone

Recent seismic studies suggest an anisotropic Mantle Transition Zone (MTZ) in areas adjacent to subducted slabs. Wadsleyite is the main anisotropy contributor in the upper MTZ, therefore the interpretation of these seismic observations requires the knowledge of single-crystal elastic moduli (C ij s) and the deformation-induced lattice preferred orientation (LPO) of wadsleyite. Wadsleyite can host up to 3 wt% water in its crystal structure as point defects in the form of hydroxyl groups, however, the combined effect of water content, Fe content, and pressure on the C ij s of wadsleyite remains unclear. In this study, we measured the high-pressure single-crystal elasticity of a synthetic hydrous Fe-bearing wadsleyite (0.14(5) wt% water, Fe#=9.4, Fe 3+ /ΣFe=0.3) up to 18.2 (2) GPa. In combination with previous experimental data, we separated the effects of pressure, water, and Fe contents on the Cijs and intrinsic elastic anisotropy of wadsleyite. Overall, our results suggest that the intrinsic elastic anisotropy of wadsleyite decreases with pressure, water, and Fe contents. At 15 GPa, increasing the water content by 0.1 wt% or Fe# by 1 decreases the V P and V S anisotropy of wadsleyite by ~1.1-1.3%, and ~0.8-1.3% in average, respectively. Combined with the LPO determined in previous deformation experiments, we modeled the seismic anisotropy in the upper MTZ generated by a sub-vertical mantle flow near cold subducted slabs and a sub-horizontal mantle flow in the ambient mantle. In both scenarios, the LPO of wadsleyite leads to V SV (vertically polarized shear wave velocity) > V SH (horizontally polarized shear wave velocity). Our results suggest that wadsleyite may account for a weak anisotropic MTZ (<1%) on the global scale. Considering the fact that water decreases the elastic anisotropy but promotes LPO of wadsleyite, seismic anisotropy may not be a good water sensor.

36 MATERIALS SCIENCE↗

Learning interpretable surface elasticity properties from bulk properties via neural network equation learners

Surface elasticity is central to understanding the mechanics and stability of surfaces and interfaces. It is characterized by quantities such as surface tension, residual surface stress, and surface stiffness. However their analytical expressions are typically difficult to derive from atomistic data, and depend strongly on modeling choices. This work presents a neural network-based equation learner which combines customized activation functions and connection-based pruning to discover parsimonious, closed-form equations for surface elasticity from atomistic simulations. Applying the method to seven face-centered cubic (FCC) metals, our equation learner uncovers interpretable equations that describe both low-Miller index and high-Miller index surface properties, capturing long-tail property distributions accurately. The discovered expressions are decoupled into two components: a universal, geometry-driven orientation function, and material-specific baseline coefficients. We find that lower-order properties such as surface tension are fundamentally geometry dependent, while higher-order properties such as surface stress and elasticity show more complex geometry and material dependence. We also relate material dependent coefficients to bulk properties, forming a clear map from bulk material properties to surface elasticity. Overall, this approach demonstrates that interpretable neurosymbolic machine learning can bridge the gap between atomistic simulations and physical laws, enabling the discovery of generalizable structure–property relationships for materials science phenomena such as surface elasticity.

Equation learning↗

An analytical elastic plastic contact model with strain hardening and frictional effects for normal and oblique impacts

Impact between metallic surfaces is a phenomenon that is ubiquitous in the design and analysis of mechanical systems. We found that to model this phenomenon, a new formulation for frictional elastic–plastic contact between two surfaces is developed. The formulation is developed to consider both frictional, oblique contact (of which normal, frictionless contact is a limiting case) and strain hardening effects. The constitutive model for normal contact is developed as two contiguous loading domains: the elastic regime and a transitionary region in which the plastic response of the materials develops and the elastic response abates. For unloading, the constitutive model is based on an elastic process. Moreover, the normal contact model is assumed to only couple one-way with the frictional/tangential contact model, which results in the normal contact model being independent of the frictional effects. Frictional, tangential contact is modeled using a microslip model that is developed to consider the pressure distribution that develops from the elastic–plastic normal contact. This model is validated through comparisons with experimental results reported in the literature, and is demonstrated to be significantly more accurate than 10 other normal contact models and three other tangential contact models found in the literature.

36 MATERIALS SCIENCE↗