Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “dynamics testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

Dynamic-stability tests on an aircraft escape module at Mach numbers from 0.40 to 2.16

Wind-tunnel measurements of the aerodynamic damping and oscillatory stability of a model of a proposed escape module for a military aircraft have been made using a small-amplitude forced-oscillation technique in pitch and yaw at Mach numbers from 0.40 to 2.16 and in roll at Mach numbers from 0.40 to 1.20. The results in pitch indicate regions in the angle-of-attack range where the model exhibits large and rapid changes in both damping and stability with angle of attack, probably caused by vortex flow over the fins. There was no pronounced effect of change in angle of attack on damping in yaw. Except for the highest Mach number, negative damping in roll was produced at high negative angles of attack.

Davenport, E. E.↗
NASA NTRS1975

Evaluation by step response tests of prototype relief valves designed for YF-12 inlet stability bleed system

Two stability bleed system relief valves were tested in a special dynamic test facility. These poppet valves are prototypes for a stability bleed system designed for use in a YF-12 flight inlet. One valve is unshielded, while the other has a special shield to eliminate the flow effect pressures on the piston. The tests determined the size of a damping orifice to be used during wind tunnel tests of the bleed system and verified an analog simulation of the valves. The effects of initial pressure level, pressure step size, and spring rate were investigated.

Dustin, M. O.↗
NASA NTRS1984

Current Status of an Organic Rankine Cycle Engine Development Program

The steps taken to achieve improved bearing life in the organic Rankine cycle (ORC) engine being developed for use on solar parabolic dishes are presented. A summary of test results is given. Dynamic tests on the machine shaft and rotors of the ORC engine are also discussed.

Barber, R. E.↗
NASA NTRS1985

Dynamic assertion testing of flight control software

Digital Flight Control System (DFCS) software was used as a test case for assertion testing. The assertions were written and embedded in the code, then errors were inserted (seeded) one at a time and the code executed. Results indicate that assertion testing is an effective and efficient method of detecting errors in flight software. Most errors are eliminate at an earlier stage in the development than before.

Andrews, D. M.↗
NASA NTRS1988

Dynamic fatigue testing of Zerodur glass-ceramic

The inherent brittleness of glass invariably leads to a large variability in strength data and a time dependence in strength. Leading rate plays a large role in strength values. Glass is found to be weaker when supporting loads over long periods of time as compared to glass which undergoes rapid leading. These properties complicate the structural design allowables for the utilization of glass components in an application such as Advanced X-ray Astrophysics Facility (AXAF). The test methodology to obtain parameters which can be used to predict the reliability and life time of Zerodur glass-ceramic which is to be used for the mirrors in the AXAF is described.

Tucker, Dennis S.↗
NASA NTRS1989

Hubble Space Telescope-Space Shuttle interface dynamic verification test

A test program has been developed for the interface between the Space Shuttle Orbiter and the Hubble Space Telescope which couples a standard modal test for a simple suspended structure with a novel, 'interface verification' test. While the free-free modal test is used to verify the high loads generating structural modes due to the interaction of internal components of the structure with the rest of the structure, the interface verification test verifies the character of the high-loading generating modes in which the structure reacts against the booster interface. The novel method excites the structure at a single payload-booster interface DOF, while all other interfaces are left free to move.

Blair, Mark A.↗
NASA NTRS1992

The Seventeenth Space Simulation Conference. Terrestrial Test for Space Success

The Institute of Environmental Sciences' Seventeenth Space Simulation Conference, 'Terrestrial Test for Space Success' provided participants with a forum to acquire and exchange information on the state of the art in space simulation, test technology, atomic oxygen, dynamics testing, contamination, and materials. The papers presented at this conference and the resulting discussions carried out the conference theme of 'terrestrial test for space success.'

Stecher, Joseph L., III↗
NASA NTRS2005

Heat Pipe Reactor Dynamic Response Tests: SAFE-100 Reactor Core Prototype

The SAFE-I00a test article at the NASA Marshall Space Flight Center was used to simulate a variety of potential reactor transients; the SAFEl00a is a resistively heated, stainless-steel heat-pipe (HP)-reactor core segment, coupled to a gas-flow heat exchanger (HX). For these transients the core power was controlled by a point kinetics model with reactivity feedback based on core average temperature; the neutron generation time and the temperature feedback coefficient are provided as model inputs. This type of non-nuclear test is expected to provide reasonable approximation of reactor transient behavior because reactivity feedback is very simple in a compact fast reactor (simple, negative, and relatively monotonic temperature feedback, caused mostly by thermal expansion) and calculations show there are no significant reactivity effects associated with fluid in the HP (the worth of the entire inventory of Na in the core is .<el, so fluid movement and temperature changes will cause very minor effects). In previous SAFE-100 tests, the point kinetics model was based on core thermal expansion via deflection measurements. It was found that core deflection was a strung function of how the SAFE-100 modules were fabricated and assembled (in terms of straightness, gaps, and other tolerances). To remove the added variable of how this particular core expands as compared to a different concept, it was decided to use a temperature based feedback model (based on several thermocouples placed throughout the core).

Bragg-Sitton, Shannon M.↗
NASA NTRS2006

Comparison of JPL and European Environmental Testing Standards

A comparison of JPL and European environmental testing standards is presented. The contents include: 1) JPL Environmental Testing Documents; 2) Focus of the Comparison; 3) Test Policy; 4) Documentation; 5) Programmatics; 6) Functional Testing; 7) Reporting; 8) Dynamics Test Levels, Durations, & Margins; 9) Thermal Test Levels, Durations, & Margins; and 10) EMC Test Levels, Durations, & Margins.

spacecraft↗
NASA NTRS2013

Multi-Mission Earth Vehicle Subsonic Dynamic Stability Testing and Analyses

Multi-Mission Earth Entry Vehicles (MMEEVs) are blunt-body vehicles designed with the purpose of transporting payloads from outer space to the surface of the Earth. To achieve high-reliability and minimum weight, MMEEVs avoid use of limited-reliability systems, such as parachutes, retro-rockets, and reaction control systems and rely on the natural aerodynamic stability of the vehicle throughout the Entry, Descent, and Landing (EDL) phase of flight. The Multi-Mission Systems Analysis for Planetary Entry (M-SAPE) parametric design tool is used to facilitate the design of MMEEVs for an array of missions and develop and visualize the trade space. Testing in NASA Langley?s Vertical Spin Tunnel (VST) was conducted to significantly improve M-SAPE?s subsonic aerodynamic models. Vehicle size and shape can be driven by entry flight path angle and speed, thermal protection system performance, terminal velocity limitations, payload mass and density, among other design parameters. The objectives of the VST testing were to define usable subsonic center of gravity limits, and aerodynamic parameters for 6-degree-of-freedom (6-DOF) simulations, for a range of MMEEV designs. The range of MMEEVs tested was from 1.8m down to 1.2m diameter. A backshell extender provided the ability to test a design with a much larger payload for the 1.2m MMEEV.

Glaab, Louis J.↗
NASA NTRS2016

V&V on a NASA Technology Demonstration Project: Low Density Supersonic Decelerator

Given their smaller budgets, but higher allowed risk posture, technology demonstration missions face different Verification and Validation (V&V) challenges than typical NASA missions. Despite these challenges, the Low Density Supersonic Decelerator (LDSD) project, managed by NASA’s Jet Propulsion Laboratory (JPL), has been extremely successful in testing new supersonic atmospheric decelerator technologies. A contribution to the project’s success is the unique V&V program that emphasized efficiency and flexibility. This paper will provide an overview of LDSD test objectives, Supersonic Flight Dynamics Tests (SFDT) performed so far, unique requirements structure and V&V processes implemented. The paper will focus on the V&V of the SFDT test architecture. Furthermore, lessons learned will also be presented at the end of the paper to aid future technology demonstration projects.

Murry, Michael L.↗