Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “design considerations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1980

Design considerations for optical heterodyne receivers: A review

The current state of knowledge concerning optical heterodyne receivers is reviewed. Following a discussion of noise processes in the heterodyne receiver and the manner in which sensitivity is increased through time integration of the detected signal, an expression for the mean square signal current is derived by mixing a coherent local oscillator with a partially coherent, quasimonochromatic source. Then the manner in which the IF signal calculation can be transferred to any convenient plane in the optical front end of the receiver is demonstrated. Using these techniques, a relatively simple equation is obtained for the coherently detected signal from an extended incoherent source and applied to the heterodyne detection of an extended thermal source and to the backscatter lidar problem where the antenna patterns of both the transmitter beam and heterodyne receiver must be taken into account. Finally, the detection of a coherent source is considered and, in particular, a distant point source such as a star or laser transmitter in a long range heterodyne communications system is discussed.

Degnan, J. J.↗
NASA NTRS1980

Initial MPTS study results: Design considerations and issues

One of the key issues identified during investigations of microwave power transmission systems from 1965 to 1976 was the need to assure that the billions of diodes on ground-based rectennas are sufficiently reliable to support long life times of approximately 30 years. Major systems studies conducted focused on waveguides; radio frequency interference and biological considerations; the relationship between performance, weight, and cost; risk assessment; crossed field directional amplifier noise; a 48 kW klystron; effects of the environment on propagation and phase control; rectenna technology; a rationale for the ground power density region; alternate technologies for orbital assembly; ionospheric effects and phase control; and reception conversion (rf to dc collector/converter).

Maynard, O. E.↗
NASA NTRS1982

Design considerations of a thermally stabilized continuous flow electrophoresis chamber 2

The basic adjustable parameters of a Beckman Continouous Particle Electrophoresis (CPE) Apparatus are investigated to determine the optimum conditions for ground based operation for comparison with space experiments. The possible application of electrically insulated copper/aluminum chamber walls is evaluated as a means to thermally stabilize or equilibrate lateral temperature gradients which exist on the walls of conventional plastic chambers and which distort the rectilinear base flow of buffer through the chamber, significantly affecting sample resolution.

Jandebeur, T. S.↗
NASA NTRS1983

Design considerations for large space electric power systems

As power levels of spacecraft rise to the 50 to 100 kW range, it becomes apparent that low voltage (28 V) dc power distribution and management systems will not operate efficiently at these higher power levels. The concept of transforming a solar array voltage at 150 V dc into a 1000 V ac distribution system operating at 20 kHz is examined. The transformation is accomplished with series-resonant inverter by using a rotary transformer to isolate the solar array from the spacecraft. The power can then be distributed in any desired method such as three phase delta to delta. The distribution voltage can be easily transformed to any desired load voltage and operating frequency. The reasons for the voltage limitations on the solar array due to plasma interactions and the many advantages of a high voltage, high frequency at distribution system are discussed.

Renz, D. D.↗
NASA NTRS1983

Design considerations for a real-time ocular counterroll instrument

A real-time algorithm for measuring three-dimensional movement of the human eye, especially torsional movement, is presented. As its input, the system uses images of the eyeball taken at video rate. The amount of horizontal and vertical movement is extracted using a pupil tracking technique. The torsional movement is then measured by computing the discrete cross-correlation function between the circular samples of successive images of the iris patterns and searching for the position of the peak of the function. A local least square interpolation around the peak of the cross-correlation function is used to produce nearly unbiased estimates of torsion angle with accuracy of about 3-4 arcmin. Accuracies of better than 0.03 deg are achievable in torsional measurement with SNR higher than 36 dB. Horizontal and vertical rotations of up to + or - 13 deg can occur simultaneously with torsion without introducing any appreciable error in the counterrolling measurement process.

Hatamian, M.↗
NASA NTRS1983

Design considerations for high-power VHF radar transceivers: The Poker Flat MST radar phase control system

Sixty-four separate 50-kW peak-power transmitters are distributed throughout the 200 x 200 meter Poker Flat MST radar antenna array. The relative phase of each transmitter is automatically controlled by a 64-channel unit located in the main building at the edge of the antenna. The phase control unit is described. In operation the RF pulse from a transmitter coupler is power divided and compared with the phase reference in a mixer. The mixer output is low-pass filtered and sampled near the center of the resulting video pulse by an amplifying sample-and-hold integrated circuit. Phase control is effected by maintaining the mixer output pulse near zero volts by amplifying the sample-and-hold output which then drives the voltage-controlled phase shifter in the direction to null the mixer output. The voltage-controlled shifter achieves over 360 deg phase shift in the range from 0.7 to 24 volts. When the voltage into the shifter tracks to either voltage limit the wrap-around control resets the voltage so that the shifter is always operating within its control range.

Ecklund, W. L.↗
NASA NTRS1983

Design considerations for FET-gated power transistors

An FET-bipolar combinational power transistor configuration (tested up to 300 V, 20 A at 100 kHz) is described. The critical parameters for integrating the chips in hybrid form are examined, and an effort to optimize the overall characteristics of the configuration is discussed. Chip considerations are examined with respect to the voltage and current rating of individual chips, the FET surge capability, the choice of triple diffused transistor or epitaxial transistor for the bipolar element, the current tailing effect, and the implementation of the bipolar transistor and an FET as single chip or separate chips. Package considerations are discussed with respect to package material and geometry, surge current capability of bipolar base terminal bonding, and power losses distribution.

Chen, D. Y.↗
NASA NTRS1982

Visible charge-coupled device (CCD) focal plane design considerations for multispectral applications

The typical Multispectral Linear Array (MLA) Instrument mission would be to gather high-resolution, radiometrically accurate earth resources data in several spectral bands over a prolonged period of time. These bands would include the visible (VIS), near infrared (NIR) and short wavelength infrared. Silicon charge-coupled imaging devices (CCDs) can be assembled into contiguous pixel focal planes which will cover the VIS/NIR region and operate reliably for several years in a space environment. A typical MLA focal plane would have approximately 12,000 pixels, with a pixel-to-pixel registration requirement on the order of + or - 0.1 pixel. The technology to assemble such focal planes has been developed and is described. The problem of polarization sensitivity associated with certain types of focal plane assemblies is addressed. Radiation effects on CCDs are also discussed, and a practical solution to the problem through the use of shielding is described.

Sadowski, H.↗
NASA NTRS1985

Feed System Design Considerations for Large Space Antenna Systems. Part 2: Single Aperture with Overlapping Feeds

Contiguous multiple beams are used to make use of the set of frequency bands at different beams at different geographical locations and achieve the most efficient use of precious frequency allocation. This is feasible only if the interference among cochannel beams is below some acceptable level, by carrier/interference (C/I) ratio. Individual beam patterns of very low sidelobes, which in turn necessitates narrow feed are required. A physically realizable solution to this problem entails either more than one reflector, more complicated optics, or breaking of each feed into a cluster of smaller elements, some of which would then be shared by adjacent beams. The latter, however, requires a complicated beamforming network (BFN) for the proper feeding of the elements. The feedpacking problem is not unique to reflector antennas and exists in lens type antennas as well. The BFN and associated problems are present in the phased array antennas and on a much larger scale. Poor scan capabilities are associated with reflector systems. The scan properties of offset fed reflector systems can be improved by choosing a very large focal length to parent reflector diameter ((F/Dp) ratio, which requires a longer boom to support the feed. In the case of reflectors with cluster feed arrangements, the scan capability for smaller F/Dp ratios is improved by proper adjustment of cluster element excitations. Such a system seems to be appropriate for up to 10 beamwidths scan. For a larger number of beams, systems with wider scan capabilities, such as phased arrays or phased array/reflector combinations, become more appealing.

Jamnejad, V.↗
NASA NTRS1985

Process and design considerations for high-efficiency solar cells

This paper shows that oxide surface passivation coupled with optimum multilayer anti-reflective coating can provide approx. 3% (absolute) improvement in solar cell efficiency. Use of single-layer AR coating, without passivation, gives cell efficiencies in the range of 15 to 15.5% on high-quality, 4 ohm-cm as well as 0.1 to 0.2 ohm-cm float-zone silicon. Oxide surface passivation alone raises the cell efficiency to or = 17%. An optimum double-layer AR coating on oxide-passivated cells provides an additional approx. 5 to 10% improvement over a single-layer AR-coated cell, resulting in cell efficiencies in excess of 18%. Experimentally observed improvements are supported by model calculations and an approach to or = 20% efficient cells is discussed.

Rohati, A.↗
NASA NTRS1984

Artificial gravity studies and design considerations for Space Station centrifuges

The requirements to and capabilities of a Space Station biological facility centrifuge are discussed on the basis of an assessment of the objectives and subjects of future microgravity biological experiments. It is argued that the facility should be capable of both acute and extended chronic exposure of test subjects and biological materials to altered-g loading. In addition, the experimental approaches and equipment for microgravity studies on a Space Station are outlined. Finally, the engineering requirements of such a centrifuge are examined, with consideration of radial gravity gradients, size, and physical access to animals.

Halstead, T. W.↗
NASA NTRS1986

Network design consideration of a satellite-based mobile communications system

Technical considerations for the Mobile Satellite Experiment (MSAT-X), the ground segment testbed for the low-cost spectral efficient satellite-based mobile communications technologies being developed for the 1990's, are discussed. The Network Management Center contains a flexible resource sharing algorithm, the Demand Assigned Multiple Access scheme, which partitions the satellite transponder bandwidth among voice, data, and request channels. Satellite use of multiple UHF beams permits frequency reuse. The backhaul communications and the Telemetry, Tracking and Control traffic are provided through a single full-coverage SHF beam. Mobile Terminals communicate with the satellite using UHF. All communications including SHF-SHF between Base Stations and/or Gateways, are routed through the satellite. Because MSAT-X is an experimental network, higher level network protocols (which are service-specific) will be developed only to test the operation of the lowest three levels, the physical, data link, and network layers.

Yan, T.-Y.↗
NASA NTRS1986

Spartan 101 structural analysis and design considerations

The final results for the Spartan 101 (Sp101) stress analysis are presented. The Special Payloads Division (SPD) is the payload integrator for the Spartan payloads. As a payload integrator of a Space Shuttle payload the SPD is responsible for all the structural safety requirements. The Spartan system includes the Spartan Flight Support Structure (SFSS) and the Spartan fly-away experiment. The Release/Engage Mechanism (REM), the Mission Peculiar Equipment (MPE), and the MPE Support Structure (MPESS) are the components of the SFSS. It is demonstrated how the full Spartan 101 system was integrated and verified before flying in the Space Shuttle. Needed analyses and testing are discussed. Key events in the Sp101 time line are also covered.

Ferragut, N. J.↗
NASA NTRS1987

Design considerations for long-lived glass mirrors for space

Large mirrors intended for long-term operation in orbital space will have to retain high reflectance in the presence of contamination or destruction by high-energy particles, meteorites, and orbiting debris. These conditions require the use of low-energy outer surfaces that resist the buildup of contamination, the use of small mirror segments that restrict local damage and facilitate replacement, and the use of surface coatings that minimize the effects of atomic oxygen and/or charge buildup. The present recommendations are based on experience accumulated with terrestrial solar-concentrator mirror materials.

Bouquet, Frank L.↗
NASA NTRS1988

Design considerations of manipulator and feel system characteristics in roll tracking

A fixed-base simulation was performed to identify and quantify interactions between the pilot's hand/arm neuromuscular subsystem and such control system features of typical modern fighter aircraft roll rate command mechanizations as: (1) force versus displacement sensing side-stick type manipulator, (2) feel force/displacement gradient, (3) feel system versus command prefilter dynamic lag, and (4) flight control system effective time delay. The experiment encompassed some 48 manipulator/filter/aircraft configurations. Displacement side-stick experiment results are given and compared with the previous force sidestick experiment results. Attention is focused on control bandwidth, excitement (peaking) of the neuromuscular mode, feel force/displacement gradient effects, time delay effects, etc. Section 5 is devoted to experiments with a center-stick in which force versus displacement sensing, feel system lag, and command prefilter lag influences on tracking performance and pilot preference are investigated.

Johnston, Donald E.↗