Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “delay errors.”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Testing of A Photon-Counting Optical Ground Receiver With Emulated Space-to-Ground Link Effects

The National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) developed and previously characterized a photon-counting optical ground receiver system. The receiver is compliant with the Consultative Committee for Space Data Systems (CCSDS) Optical Communications Coding and Synchronization High Photon Efficiency (HPE) Standard. The standard will be used on the Optical Artemis-2 Orion (O2O) communications demonstration and the Deep Space Optical Communication (DSOC) project aboard the Psyche spacecraft. The receiver system consists of a fiber interconnect, up to sixteen superconducting nanowire single-photon detectors (SNSPDs), and a field programmable gate array (FPGA) based receive modem. Previously, the receiver system architecture was described and test results without emulated link effects were presented. SNSPD device properties, which impact detection jitter and time delay, can limit the receiver dynamic range, especially when operating with varying flux rates (>10 dB) between detectors. Codeword error-rate curves with and without simulated clock drifts attributed to Doppler shift and space transmitter clock differences are presented. Results with ±66 ppm clock differences show minimal performance impact (<0.2 dB). Test results show that the receiver dynamic range (>28 dB) is limited by changing SNSPD detection delays at high photon flux rates.

optical communications↗
DOE OSTI2025

Airport Delay Prediction with Temporal Fusion Transformers

Since flight delay hurts passengers, airlines, and airports, its prediction becomes crucial for the decision-making of all stakeholders in the aviation industry and thus has been attempted by various previous research. However, previous delay predictions are often categorical and at a highly aggregated level. To improve that, this study proposes to apply the novel Temporal Fusion Transformer model and predict numerical airport arrival delays at quarter hour level for U.S. top 30 airports. Inputs to our model include airport demand and capacity forecasts, historic airport operation efficiency information, airport wind and visibility conditions, as well as en-route weather and traffic conditions. The results show that our model achieves satisfactory performance measured by small prediction errors on the test set. In addition, the interpretability analysis of the model outputs identifies the important input factors for delay prediction.

Liu, Ke [University of California Berkeley]↗
NASA NTRS1984

Tropospheric Delay Effects in Radio Interferometry

A new tropospheric mapping function is derived which is more accurate than previous mapping functions above elevations of 4 degrees. The error due to the given analytic approximation is estimated to be less than 0.02% for elevation angles larger than 6 degrees, (less than 0.4 cm at 6 degrees, and approximately 0.004% or 0.03 cm at 20 degrees). The mathematical expansion used in the derivation is valid for any laterally homogeneous atmospheric model of refractivity. The new mapping function, computer generated ray tracing tables and other mapping functions are compared. The results can be used in correcting for tropospheric delays of radio signals.

Lanyi, G.↗
NASA NTRS2023

Single-Band VLBI Absolute Astrometry

The ionospheric path delay impacts single-band very long baseline interferometry (VLBI) group delays, which limits their applicability for absolute astrometry. I consider two important cases: when observations are made simultaneously in two bands, but delays in only one band are available for a subset of observations and when observations are made at one band design. I developed optimal procedures of data analysis for both cases using Global Navigation Satellite System (GNSS) ionosphere maps, provided a stochastic model that describes ionospheric errors, and evaluated their impact on source position estimates. I demonstrate that the stochastic model is accurate at a level of 15%. I found that using GNSS ionospheric maps as is introduces serious biases in estimates of declination and I developed a procedure that almost eliminates them. I found serendipitously that GNSS ionospheric maps have multiplicative errors and have to be scaled by 0.85 in order to mitigate the declination bias. A similar scale factor was found in comparison of the vertical total electron content from satellite altimetry against GNSS ionospheric maps. I favor interpretation of this scaling factor as a manifestation of the inadequacy of the thin shell model of the ionosphere. I showed that we are able to model the ionospheric path delay to the extent that no noticeable systematic errors emerge and we are able to assess adequately the contribution of the ionosphere-driven random errors on source positions. This makes single-band absolute astrometry a viable option that can be used for source position determination.

Radio astrometry↗
NASA NTRS1985

An adaptive quantization method for burst mode synthetic aperture radar data

Synthetic aperture radar (SAR) has high data rate because it collects and processes the data coherently. The data rate limitation of the system has to be satisfied while maintaining good image quality. Thus, a quantizer with minimum data rate and high SNR should be employed. An adaptive quantization method is proposed for the burst mode SAR. This adaptive quantizer uses uniformly quantized data to select a subset of bits which is equivalent to changing the step size of the uniform quantizer. A simple implementation which uses the previous burst data to compute the local statistics for the bit selection is presented. The use of previous burst simplifies the implementation because it does not require storage or delay; however, an abrupt change in the terrain could result in incorrect bit selection. An error analysis of this implementation and comparison of two burst mode SAR images formed using the uniformly quantized and adaptively quantized data is presented.

Joo, T. H.↗
NASA NTRS1986

A new algorithm for microwave delay estimation from water vapor radiometer data

A new algorithm has been developed for the estimation of tropospheric microwave path delays from water vapor radiometer (WVR) data, which does not require site and weather dependent empirical parameters to produce high accuracy. Instead of taking the conventional linear approach, the new algorithm first uses the observables with an emission model to determine an approximate form of the vertical water vapor distribution which is then explicitly integrated to estimate wet path delays, in a second step. The intrinsic accuracy of this algorithm has been examined for two channel WVR data using path delays and stimulated observables computed from archived radiosonde data. It is found that annual RMS errors for a wide range of sites are in the range from 1.3 mm to 2.3 mm, in the absence of clouds. This is comparable to the best overall accuracy obtainable from conventional linear algorithms, which must be tailored to site and weather conditions using large radiosonde data bases. The new algorithm's accuracy and flexibility are indications that it may be a good candidate for almost all WVR data interpretation.

Robinson, S. E.↗
NASA NTRS1987

Two-color short-pulse laser altimeter measurements of ocean surface backscatter

The timing and correlation properties of pulsed laser backscatter from the ocean surface have been measured with a two-color short-pulse laser altimeter. The Nd:YAG laser transmitted 70- and 35-ps wide pulses simultaneously at 532 and 355 nm at nadir, and the time-resolved returns were recorded by a receiver with 800-ps response time. The time-resolved backscatter measured at both 330-m and 1291-m altitudes showed little pulse broadening due to the submeter laser spot size. The differential delay of the 355-nm and 532-nm backscattered waveforms were measured with a rms error of about 75 ps. The change in aircraft altitudes also permitted the change in atmospheric pressure to be estimated by using the two-color technique.

Abshire, James B.↗
NASA NTRS1989

Reliable magnetic tape recording for real-time data acquisition systems

The design of a real-time magnetic tape I/O system using automatic error recovery and data spooling is discussed. Real time requirements (data acquired at one rate and recorded at another by queing) must be met and data integrity must be provided regardless of tape failures or I/O errors. Automatic blocking services should be used for multiple local records storage. Avoidance of operational delays and loss of data is essential, noting the problems of the tape drives of the NASA Langley cryogenic wind tunnel. A series of block diagrames and flow charts are included.

Richard W Ross↗
NASA NTRS2002

Modulation Study for Beam Steerable Reflectarray Antennas

The reflectarray antenna is a power-efficient antenna but with an inherent intersymbol interference (ISI) problem with digital modulations. The composite signal model of a reflectarray is established. The ISI is characterized by the signal components delays. The feed-to-element distance and the element-to-observation distance contribute to the total delay, with the latter having the major effect. The effect of typical phase shifters' phase errors is analyzed and evaluated. Simulations are performed. The analytical and simulation results for an example reflectarray at f(sub c) = 26.5 GHz and bit rate of 1.325 Gbps show that the BER degradation due to ISI is proportional to the symbol rate and the loss ranges from less than 1 dB to around 2 dB in E(sub b)/N(sub o), depending on original E(sub b)/N(sub o), for BPSK, QPSK, 8PSK and 16QAM. The phase error effect is negligible for lower order modulations and is unacceptable for higher order modulations such as 64 and 256QAM.

Xiong, Fuqin↗
NASA NTRS2024

Clock Synchronization Characterization of the Washington DC Metropolitan Area Quantum Network (DC-QNet)

Quantum networking protocols relying on interference and precise time-of-flight measurements require high-precision clock synchronization. This study describes the design, implementation, and characterization of two optical time transfer methods in a metropolitan-scale quantum networking research testbed. With active electronic stabilization, sub-picosecond time deviation (TDEV) was achieved at integration times between 1 s and 10 5 s over 53 km of deployed fiber. Over the same integration periods, 10-picosecond level TDEV was observed using the White Rabbit-Precision Time Protocol (WR-PTP) over 128 km. Measurement methods are described to understand the sources of environmental fluctuations on clock synchronization towards the development of in-situ compensation methods. Path delay gradients, chromatic dispersion, polarization drift, and optical power variations all contributed to clock synchronization errors. The results from this study will inform future work in the development of link noise management methods essential for enabling experimental research in developing practical quantum networking protocols.

PIKTime↗
NASA NTRS2006

The Effectiveness of TAG or Guard-Gates in SET Suppression Using Delay and Dual-Rail Configurations at 0.35 microns

Design options for decreasing the susceptibility of integrated circuits to Single Event Upset (SEU) fall into two categories: (1) increasing the critical charge to cause an upset at a particular node, and (2) employing redundancy to mask or correct errors. With decreasing device sizes on an Integrated Circuit (IC), the amount of charge required to represent a logic state has steadily reduced. Critical charge methods such as increasing drive strength or increasing the time required to change state as in capacitive or resistive hardening or delay based approaches extract a steadily increasing penalty as a percentage of device resources and performance. Dual redundancy is commonly assumed only to provide error detection with Triple Modular Redundancy (TMR) required for correction, but less well known methods employ dual redundancy to achieve full error correction by voting two inputs with a prior state to resolve ambiguity. This requires special circuits such as the Whitaker latch [1], or the guard-gate [2] which some of us have called a Transition AND Gate (TAG) [3]. A 2-input guard gate is shown in Figure 1. It is similar to a Muller Completion Element [4] and relies on capacitance at node "out" to retain the prior state when inputs disagree, while eliminating any output buffer which would be susceptible to radiation strikes. This paper experimentally compares delay based and dual rail flip-flop designs wherein both types of circuits employ guard-gates to optimize layout and performance, and draws conclusions about design criteria and suitability of each option. In both cases a design goal is protection against Single Event Transients (SET) in combinational logic as well as SEU in the storage elements. For the delay based design, it is also a goal to allow asynchronous clear or preset inputs on the storage elements, which are often not available in radiation tolerant designs.

Shuler, Robert L.↗
NASA NTRS1987

Performance analysis of an optimal file transfer protocol for integrated mobile satellite services

A file-transfer protocol based on the selective-repeat automatic-retransmission-request (ARQ) scheme has been developed for the Mobile Satellite Experiment (MSAT-X). In this protocol, each file is divided into packets, which are error-detected and acknowledge individually. A file can be transferred in either the open- or closed-end connection. In the open-end connection, the file is transmitted continuously according to the selective-repeat scheme until all packets are positively acknowledged; in the closed-end connection, each retransmission will initiate its own connection request. The relationship between the packet size and the average end-to-end delay in the mobile fading environment is investigated. The communications channel uses trellis-coded modulation with symbol interleaving, packet replication, and error detection. The packet error performance in such a channel is evaluated by simulation, and the optimal packet size for various operating conditions is derived, using the simulated results. It is shown that for a symbol-energy-to-noise ratio of 12 dB, each file should be divided into packets of length between 256 bits and 512 bits (excluding the overhead) to minimize the average end-to-end delay.

Wang, Charles C.↗
NASA NTRS2011

Scatterometer-Calibrated Stability Verification Method

The requirement for scatterometer-combined transmit-receive gain variation knowledge is typically addressed by sampling a portion of the transmit signal, attenuating it with a known-stable attenuation, and coupling it into the receiver chain. This way, the gain variations of the transmit and receive chains are represented by this loop-back calibration signal, and can be subtracted from the received remote radar echo. Certain challenges are presented by this process, such as transmit and receive components that are outside of this loop-back path and are not included in this calibration, as well as the impracticality for measuring the transmit and receive chains stability and post fabrication separately, without the resulting measurement errors from the test set up exceeding the requirement for the flight instrument. To cover the RF stability design challenge, the portions of the scatterometer that are not calibrated by the loop-back, (e.g., attenuators, switches, diplexers, couplers, and coaxial cables) are tightly thermally controlled, and have been characterized over temperature to contribute less than 0.05 dB of calibration error over worst-case thermal variation. To address the verification challenge, including the components that are not calibrated by the loop-back, a stable fiber optic delay line (FODL) was used to delay the transmitted pulse, and to route it into the receiver. In this way, the internal loopback signal amplitude variations can be compared to the full transmit/receive external path, while the flight hardware is in the worst-case thermal environment. The practical delay for implementing the FODL is 100 s. The scatterometer pulse width is 1 ms so a test mode was incorporated early in the design phase to scale the 1 ms pulse at 100-Hz pulse repetition interval (PRI), by a factor of 18, to be a 55 s pulse with 556 s PRI. This scaling maintains the duty cycle, thus maintaining a representative thermal state for the RF components. The FODL consists of an RF-modulated fiber-optic transmitter, 20 km SMF- 28 standard single-mode fiber, and a photodetector. Thermoelectric cooling and insulating packaging are used to achieve high thermal stability of the FODL components. The chassis was insulated with 1-in. (.2.5-cm) thermal isolation foam. Nylon rods support the Micarta plate, onto which are mounted four 5-km fiber spool boxes. A copper plate heat sink was mounted on top of the fiber boxes (with thermal grease layer) and screwed onto the thermoelectric cooler plate. Another thermal isolation layer in the middle separates the fiberoptics chamber from the RF electronics components, which are also mounted on a copper plate that is screwed onto another thermoelectric cooler. The scatterometer subsystem fs overall stability was successfully verified to be calibratable to within 0.1 dB error in thermal vacuum (TVAC) testing with the fiber-optic delay line, while the scatterometer temperature was ramped from 10 to 30 C, which is a much larger temperature range than the worst-case expected seasonal variations.

McWatters, Dalia A.↗
NASA NTRS1987

Error propagation in a digital avionic mini processor

A methodology is introduced and demonstrated for the study of error propagation from the gate to the chip level. The importance of understanding error propagation derives from its close tie with system activity. In this system the target system is BDX-930, a digital avionic multiprocessor. The simulator used was developed at NASA-Langley, and is a gate level, event-driven, unit delay, software logic simulator. An approach is highly structured and easily adapted to other systems. The analysis shows the nature and extent of the dependency of error propagation on microinstruction type, assembly level instruction, and fault-free gate activity.

Lomelino, Dale L.↗
NASA NTRS1972

Testing relativistic gravity theories using radio tracking data from planetary orbiting spacecraft.

We present a thorough analysis of a computational method for determining the numerical values of the relativity and other related dynamical parameters using two-way Doppler and ranging data from planetary orbiting spacecraft. The computational method consists of two parts. From Doppler data we first determine the earth-planet components of the position of the orbiting spacecraft relative to the center of gravity of the planet to high accuracy; adding the observed spacecraft range yields a range value to the center of the planet. These constructed earth-planet range data, referred to as normal points, are then treated as raw data in a regression analysis combined with planetary radar delay and meridian circle measurements to solve for the significant solar system dynamical parameters. The major errors sources in the planetary orbiter process are enumerated and their individual effects on the overall accuracy of the normal point accuracies are presented. The accuracies of the parameter estimates as a function of time, data sampling, and a priori assumptions are illustrated.

Jordan, J. F.↗
NASA NTRS1979

Group-delay standards

Delay-line standards have been tested by three independent laboratories using six different methods. Results are published in report showing delay values obtained from 15-, 30-, and 60-ns cables by different laboratories. Study of potential error sources indicates that reflection errors due to discontinuities at ends of cables are usually small.

Beatty, R. W.↗
NASA NTRS1981

Atmospheric media effects on ARIES baseline determination

Different types of media effects on ARIES baseline determination are compared. The effectiveness of simple ionospheric calibration models are studied. To perform the covariance analysis, an ARIES observation sequence needs to be assumed. For the current purposes, the observation sequence is selected to be that of experiment 80D over the JPL/Goldstone baseline (approximately 180 km). This experiment consisted of 96 observations over a period of approximately 25 hours on March 25 to 26, 1980. It is found through covariance analyses that the component most sensitive to media depends heavily upon the correlation, between the two stations, of the media effects. It is also found that relying on the cancellation of ionospheric delays between the two ray paths of VLBI observations at S band results in a large error in baseline length determination. High degree removal of ionospheric effects is possible with a crude model, providing correct diurnal peak and minimum ionospheric levels are input.

Wu, S. C.↗