SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Interface design between a probe and a spacecraft requires not only technical considerations but also management planning and mission analysis interactions. Two further aspects of importance are the flyby versus the probe trade-off, and the relay link design and data handling optimization.
Considerations of planetary quarantine for the outer planets covering prelaunch, launch, and spacecraft conditions are outlined. A basic contamination equation is included.
Special considerations for oxygen systems engineering with respect to system design, fabrication, and use are studied. The concerns for oxygen systems include the problems of leakage and erosion, difficulties that arise from dynamic processes, and the sensitivity of oxygen systems to contamination and cleaning requirements.
A radar mapping mission to Venus is under consideration by NASA for the 1980s. The science objectives of the mission are to determine the geologic history of the planet; map the major topographic features and provide limited detailed geologic and terrain analysis of potential probe landing sites. Because of the thick Venusian atmosphere, a synthetic-aperture side-looking radar system has been selected as the most practical remote sensing instruments to use. Topographic data are the most useful for achieving the science goals of the mission. The radar system variables and mission parameters must be specified to maximize topographic data returns while being compatible with engineering and cost restraints. A baseline imaging resolution of 100 meters, with ability to obtain some higher-resolution coverage, is acceptable. Total planet coverage is desirable but the primary science objectives can be achieved if at least one entire hemisphere is imaged.
The Shuttle/Orbiter Program requirements relative to operational and performance parameters of the CCTV (closed circuit television) subsystem and their influence upon design considerations are presented. The anticipated use of the CCTV for rendezvous, docking, manipulator arm operation, satellite inspection and general orbiter operations is outlined to establish the performance requirements of each subsystem element. Typical physical characteristics, interface parameters, and remote-control design philosophy are briefly described.
Probe design considerations for a 1981 Pioneer Jupiter Orbiter/Probe mission are summarized. Extensive engineering analysis, design, and proof-of-concept testing of a reference probe system developed during the past three years are reviewed. Mission compatibility, science measurements, environmental characteristics, spacecraft interfaces, subsystem constraints, technology development, and programmatic factors are reviewed and discussed. It is demonstrated that for a low-entry-angle, daylight mission to Jupiter a 150 kg semiautonomous entry probe system utilizing state of the art technology is compatible with all the requirements.
Vacuum considerations in the techniques for design, fabrication, and testing of space simulators are discussed. Particular emphasis is given to a diffusion pump-rotary pump combination for the vacuum system.
One of the many factors which must be considered in performance evaluation of solar energy systems is the relative merit of a given solar energy system when compared to a standard conventional system. Although initial and operational costs will be dominant factors in the comparison of the two types of systems and will be given prime consideration in system selection, sufficient data are not yet available for a definitive treatment of these variables. It is possible, however, to formulate relationships between the nonsolar energy requirements of the solar energy systems and the energy requirements of a conventional system in terms of the primary performance parameters of the systems. Derivations of such relationships, some parametric data for selected ranges of the performance parameters, and data with respect to limiting conditions are presented.
The analytical considerations which support the computation of (1) two components of the velocity vector from an X-array and (2) the transverse vorticity from the X-array and an adjacent parallel wire pair are presented. The electronic circuit which will execute these computations at a 50 khz rate is also described. The factors limiting the accuracy of the measurements are identified and quantitative estimates are given for a typical x-probe. An extensive analysis of the factors which effect the output and which are unknown (or unknowable) during the measurements is presented. Quantitative estimates of these effects are developed in the form of an uncertainty analysis. Numerical values, calculated using the analytical structure of the response equations, are tabulated; other estimates which require special experiments are described.
Special considerations in the planning of Space Shuttle missions for multidiscipline applications are summarized. Selection of orbits and launch times, the optimum operations schedule and viewing opportunities for a given mission are discussed. Trade-offs between the limitations of a mission-peculiar sensor mount and time requirements for sensor retraction/deployment operations in the planning of the payload mounting design are considered. It is suggested that payloads which are largely automated or whose operation is not orbit-time sensitive be considered as possible 'fill-ins' between opportunity-constrained operations. Sequential scheduling of payload operations and delayed real-time data transmission may be means of avoiding RF interference between payloads and with Orbiter communications links, and of maintaining resource demands within manageable levels.
A fixed beam array antenna approach is proposed to meet the omnidirectional receiving and transmitting requirements of LST (Large Space Telescope). The proposed method uses an antenna of known performance and scales the size and frequency to conform with the LST 1/5-th scale model. The simplification that the approach provides over switching antenna elements on board the LST or switching from the ground by frequency diversity makes it worthy of consideration against the factors of performance, cost, reliability, and operations complexity. For LST applications, the system capabilities, requirements, and margins are summarized. The areas to be covered by further investigations into the proposed LST antenna are noted.
The increased search for alternative energy sources has lead to renewed interest and studies of large wind-driven generators. This paper presents the results and considerations of such an investigation. The paper emphasizes the concept selection of wind-driven generators, system optimization, control system design, safety aspects, economic viability on electric utility systems and potential electric system interfacing problems.
Two types of reusable surface insulation under consideration for Space Shuttle applications have been analyzed for flutter stability. The first consisted of silicone rubber-coated Nomex felt bonded to the skin of the vehicle; the second consisted of silicone tiles with ceramic coating on five faces, bonded to Nomex felt which was then attached to the vehicle skin. The piston theory was used to compute the aerodynamic forces on the basis of simple models on the two systems. Exact solutions were obtained, and the effect of different parameters of the flutter stability boundary was investigated. Possible reasons for the slow convergence of the Galerkin technique for analyzing membrane flutter are suggested, and a consistent set of nondimensional parameters convenient for flutter studies is introduced.
A study was conducted to investigate major design considerations involved in the application of laminar flow control to the wings and empennage of long range subsonic transport aircraft compatible with initial operation in 1985. For commercial transports with a design mission range of 10,186 km (5500 n mil) and a payload of 200 passengers, parametric configuration analyses were conducted to evaluate the effect of aircraft performance, operational, and geometric parameters on fuel efficiency. Study results indicate that major design goals for aircraft optimization include maximization of aspect ratio and wing loading and minimization of wing sweep consistent with wing volume and airport performance requirements.
A number of remote sensing or surveillance tasks (e.g., fire fighting, crop monitoring) in the civilian sector of our society may be performed in a cost effective manner by use of small remotely piloted aircraft (RPA). This study was conducted to determine equipment (and the associated technology) that is available, and that could be applied to the mini-RPA and to examine the potential applications of the mini-RPA with special emphasis on the wild fire surveillance mission. The operational considerations of using the mini-RPA as affected by government regulatory agencies were investigated. These led to equipment requirements (e.g., infra-red sensors) over and above those for the performance of the mission. A computer technology survey and forecast was performed. Key subsystems were identified, and a distributed microcomputer configuration, that was functionally modular, was recommended. Areas for further NASA research and development activity were also identified.
A discussion is presented on the problems encountered in the design of a reference cell that meets basic criteria, starting with basic design considerations, and proceeding with the precautions taken to ensure a global monitoring capability. The effects of the variations in atmospheric conditions on the calibration and use of reference cells are presented along with a discussion of the simplifications brought about by the use of spectrally matched test and reference cells. Finally, a method of matching test modules and arrays to reference cells by a red/blue response ratio technique is described.
A description is given of some of the more significant thermal design considerations employed in the development and qualification of the monopropellant hydrazine terminal descent engines on the Viking Mars lander spacecraft. The terminal descent engine operates in a blowdown and throttling mode, which results in an operating thrust range of 638 to 90 lbf. Martian entry thermal design boundary conditions are described, along with resulting radiative and conductive engine thermal isolation hardware. Test results are presented, showing engine thermal design performance as compared with specified requirements. General engine materials of construction are described, along with Hastelloy B shell structural characteristics, which were extended to 2000 F by test and are compared with limited existing MIL-HDBK-5 data. Subscale test results are presented, showing the maximum catalyst bed cylinder design temperature of 1970 F. Test results also are presented, showing local reactor internal convective heat-transfer coefficients. Such data are unique, since the engine employs a completely radial flow catalyst bed design. This design approach is the first of its kind in the monopropellant hydrazine gas generator field to be flight qualified.
A numerical study to determine the temperature distribution in the rotor of a radial inflow turbine is presented. Internal cooling passages are modeled in the present formulation in order to carry out solid and coolant temperature computations simultaneously resulting in a considerable computer time savings. The stresses due to centrifugal and thermal loadings are determined in an actual rotor and the effect of cooling design on its mechanical integrity is discussed.