Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “code comparisons”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Recent advances in Runge-Kutta schemes for solving 3-D Navier-Stokes equations

A thin-layer Navier-Stokes has been developed for solving high Reynolds number, turbulent flows past aircraft components under transonic flow conditions. The computer code has been validated through data comparisons for flow past isolated wings, wing-body configurations, prolate spheroids and wings mounted inside wind-tunnels. The basic code employs an explicit Runge-Kutta time-stepping scheme to obtain steady state solution to the unsteady governing equations. Significant gain in the efficiency of the code has been obtained by implementing a multigrid acceleration technique to achieve steady-state solutions. The improved efficiency of the code has made it feasible to conduct grid-refinement and turbulence model studies in a reasonable amount of computer time. The non-equilibrium turbulence model of Johnson and King has been extended to three-dimensional flows and excellent agreement with pressure data has been obtained for transonic separated flow over a transport type of wing.

Vatsa, Veer N.↗
NASA NTRS2010

Comparison of CFD Predictions with Shuttle Global Flight Thermal Imagery and Discrete Surface Measurements

Surface temperature measurements from the STS-119 boundary-layer transition experiment on the space shuttle orbiter Discovery provide a rare opportunity to assess turbulent CFD models at hypersonic flight conditions. This flight data was acquired by on-board thermocouples and by infrared images taken off-board by the Hypersonic Thermodynamic Infrared Measurements (HYTHIRM) team, and is suitable for hypersonic CFD turbulence assessment between Mach 6 and 14. The primary assessment is for the Baldwin-Lomax and Cebeci-Smith algebraic turbulence models in the DPLR and LAURA CFD codes, respectively. A secondary assessment is made of the Shear-Stress Transport (SST) two-equation turbulence model in the DPLR code. Based upon surface temperature comparisons at eleven thermocouple locations, the algebraic-model turbulent CFD results average 4% lower than the measurements for Mach numbers less than 11. For Mach numbers greater than 11, the algebraic-model turbulent CFD results average 5% higher than the three available thermocouple measurements. Surface temperature predictions from the two SST cases were consistently 3 4% higher than the algebraic-model results. The thermocouple temperatures exhibit a change in trend with Mach number at about Mach 11; this trend is not reflected in the CFD results. Because the temperature trends from the turbulent CFD simulations and the flight data diverge above Mach 11, extrapolation of the turbulent CFD accuracy to higher Mach numbers is not recommended.

Wood, William A.↗
NASA NTRSDate not supplied

Performance Characteristics of a Boundary Layer Ingesting Inlet - Distortion Tolerant Fan Through CFD Code Coupling

A method of constructing a high-fidelity simulation using two NASA CFD codes, Launch Ascent and Vehicle Aerodynamics (LAVA), which is the general-purpose solver, and a turbomachinery specific code NASA-TURBO (TURBO), will be presented. Validation of the code coupling is performed through comparison to experimental data obtained in the 2017 wind tunnel test of NASA’s Boundary Layer Ingesting Inlet - Distortion Tolerant Fan (BLI2DTF). For the simulation, the external flow field is computed by LAVA utilizing a steady-state Reynolds-averaged Navier-Stokes (RANS) methodology. Data from LAVA is exchanged with TURBO, which simulated the propulsor utilizing an unsteady-RANS methodology. A sensitivity analysis is performed using averaged and instantaneous data transfer between the two codes, as well as varying the amount of simulation time TURBO computes between updates. The results of the coupled simulations appear to replicate the BLI2DTF experiment correctly. Static pressure taps leading into and around the nacelle, total pressure ratio and efficiency of the propulsor, and profiles of total temperature, pressure, and Mach number at the rear measurement plane, aft of the propulsor, are in good agreement with experimental data. These results provide confidence that the coupled simulation is behaving in a physically realizable manner.

CFD↗
NASA NTRS1983

Computational analysis for an advanced transport configuration with engine nacelle

A small-disturbance transonic analysis code is used to calculate the flow-field effects of adding an engine nacelle to a wing/body configuration. Analyses are performed on an advanced transport configuration with and without engine nacelles. Two nacelle shapes are analyzed and the effects of the nacelle installation on pressure distributions are compared with experimental results obtained by shifting the nacelle longitudinally and vertically relative to the wing. Effects of varying the nacelle installation yaw angle are also analyzed and compared with experimental data. These comparisons show that the analysis code is adequately sensitive to variations in nacelle shape, longitudinal and vertical location beneath the wing, and the nacelle installation yaw angle. Results indicate that the code can be used as an effective guide during the design process.

Waggoner, E. G.↗
NASA NTRS1994

LSENS: A General Chemical Kinetics and Sensitivity Analysis Code for homogeneous gas-phase reactions. Part 1: Theory and numerical solution procedures

LSENS, the Lewis General Chemical Kinetics and Sensitivity Analysis Code, has been developed for solving complex, homogeneous, gas-phase chemical kinetics problems and contains sensitivity analysis for a variety of problems, including nonisothermal situations. This report is part 1 of a series of three reference publications that describe LENS, provide a detailed guide to its usage, and present many example problems. Part 1 derives the governing equations and describes the numerical solution procedures for the types of problems that can be solved. The accuracy and efficiency of LSENS are examined by means of various test problems, and comparisons with other methods and codes are presented. LSENS is a flexible, convenient, accurate, and efficient solver for chemical reaction problems such as static system; steady, one-dimensional, inviscid flow; reaction behind incident shock wave, including boundary layer correction; and perfectly stirred (highly backmixed) reactor. In addition, the chemical equilibrium state can be computed for the following assigned states: temperature and pressure, enthalpy and pressure, temperature and volume, and internal energy and volume. For static problems the code computes the sensitivity coefficients of the dependent variables and their temporal derivatives with respect to the initial values of the dependent variables and/or the three rate coefficient parameters of the chemical reactions.

Radhakrishnan, Krishnan↗
NASA NTRS2011

Test Generator for MATLAB Simulations

MATLAB Automated Test Tool, version 3.0 (MATT 3.0) is a software package that provides automated tools that reduce the time needed for extensive testing of simulation models that have been constructed in the MATLAB programming language by use of the Simulink and Real-Time Workshop programs. MATT 3.0 runs on top of the MATLAB engine application-program interface to communicate with the Simulink engine. MATT 3.0 automatically generates source code from the models, generates custom input data for testing both the models and the source code, and generates graphs and other presentations that facilitate comparison of the outputs of the models and the source code for the same input data. Context-sensitive and fully searchable help is provided in HyperText Markup Language (HTML) format.

Henry, Joel↗
NASA NTRSDate not supplied

SpaceX Dragon 1 Post Flight MMOD Inspection Campaign

Introduction The SpaceX Dragon 1 spacecraft performed 20 resupply missions to the International Space Station (ISS) between 2012 and 2020. After each mission, a team from the NASA John-son Space Center Hypervelocity Impact Technology Group inspected each Dragon 1 capsule for hypervelocity impact damage features. Data from these inspections are collected into a database that includes impact feature dimensions as well as the location on the vehicle. Additional details on the type and size of particle that produced the damage site are provided when sampling data and definitive spectroscopic analysis results are available. Observation data can be compared with impact estimates from risk assessment codes as a check on the micrometeoroid and orbital debris (MMOD) environment predictions. Scope A general description of the areas of the vehicle that were inspected are provided as well as mission details such as exposure duration and launch dates. The paper documents the general inspection procedure for collection of data and the post inspection data analysis process. It also provides details of the observation data collected as well as the results of analysis of intact samples collected for spectroscopic analysis to discern the source of the impacting particle. A comparison between observed impacts and the expected number of damage features calculated by Bumper 3 with the latest MMOD environments are also presented. Findings Statistics on the >300 impact features documented in the database will provide insight into the depth to diameter ratios and other relationships. The quality of the comparison between the observations and code predictions are dependent on several factors. The paper provides de-tails of each of these variables. (1) Damage equations (2) Impact condition assumptions a. Projectile density b. Impact speed c. Impact angle (3) Analysis results a. pre-flight vs. on-orbit damage b. MMOD vs. non-MMOD Conclusions and Recommendations The ISS visiting vehicle impact database is an ongoing project. SpaceX provides crew rotations as well as resupply and cargo return with the Dragon 2 spacecraft. Sierra Space is manifested for resupply and cargo return services starting in 2023. Boeing is expected to provide crew rotations as well. All of these spacecraft will provide additional opportunities for post flight MMOD inspections of space exposed hardware. Acknowledgements Over the course of the inspection campaign various personnel at the SpaceX Texas Test Site in McGregor and at the SpaceX headquarters in Hawthorne CA provided valuable support to this activity.

James L Hyde↗
NASA NTRS1993

Navier-Stokes computations and experimental comparisons for multielement airfoil configurations

A two-dimensional unstructured Navier-Stokes code is utilized for computing the flow around multielement configurations. Comparisons are shown for a landing configuration with an advanced-technology flap as well as for a takeoff configuration. For each, a grid convergence study is conducted to assess inaccuracies caused by inadequate grid resolution. Although adequate resolution is obtained for determining the pressure distributions, further refinement is needed to sufficiently resolve the velocity profiles at high angles of attack. For the advanced flap configuration, comparisons of pressure distributions and lift are made with experimental data. Here, two flap riggings and two Reynolds numbers are considered. In general, the trends caused by variations in these quantities are well predicted by the computations, although the angle of attack for maximum lift is overpredicted. For the takeoff configuration, comparisons between pressures, velocity profiles, and Reynolds stresses are made at a single angle of attack with generally good agreement.

Anderson, W. K.↗
NASA NTRS1976

Comparison of rate one-half, equivalent constraint length 24, binary convolutional codes for use with sequential decoding on the deep-space channel

Virtually all previously-suggested rate 1/2 binary convolutional codes with KE = 24 are compared. Their distance properties are given; and their performance, both in computation and in error probability, with sequential decoding on the deep-space channel is determined by simulation. Recommendations are made both for the choice of a specific KE = 24 code as well as for codes to be included in future coding standards for the deep-space channel. A new result given in this report is a method for determining the statistical significance of error probability data when the error probability is so small that it is not feasible to perform enough decoding simulations to obtain more than a very small number of decoding errors.

Massey, J. L.↗
NASA NTRS1992

Development of a CFD code for internal flows in liquid fueled engines

To support the design efforts of engines in which liquid propellants are used, one is often required to analyze incompressible, two-dimensional or axisymmetric flows within ducts and cavities with rotating walls and complicated geometries. The steady-state solution is of interest in most cases. This code is intended to provide a tool for efficient computational fluid dynamics (CFD) analysis of such flow problems, taking advantage of the artificial compressibility concept and the Beam-Warming numerical scheme modified for second order accurate, implicit boundary conditions. These concepts ensure a stable, robust, and accurate algorithm due to the reduced speed of sound and the accuracy of the boundary conditions. The code is dedicated only to two-dimensional or axisymmetric flows with or without swirl. Three-dimensional computation is excluded to increase efficiency and speed. This paper briefly presents the theory of the code, as well as several benchmark applications with comparison to well known analytical solutions. In all these test cases, the code produced accurate results.

Dakhoul, Youssef↗
NASA NTRS2004

Comparison of SPHC Hydrocode Results with Penetration Equations and Results of Other Codes

The SPHC hydrodynamic code was used to simulate impacts of spherical aluminum projectiles on a single-wall aluminum plate and on a generic Whipple shield. Simulations were carried out in two and three dimensions. Projectile speeds ranged from 2 kilometers per second to 10 kilometers per second for the single-wall runs, and from 3 kilometers per second to 40 kilometers per second for the Whipple shield runs. Spallation limit results of the single-wall simulations are compared with predictions from five standard penetration equations, and are shown to fall comfortably within the envelope of these analytical relations. Ballistic limit results of the Whipple shield simulations are compared with results from the AUTODYN-2D and PAM-SHOCK-3D codes presented in a paper at the Hypervelocity Impact Symposium 2000 and the Christiansen formulation of 2003.

Evans, Steven W.↗
NASA NTRS1987

Implementation and validation of a wake model for vortex-surface interactions in low speed forward flight

The wake model was implemented using a VAX 750 and a Microvax II workstation. Online graphics capability using a DISSPLA graphics package. The rotor model used by Beddoes was significantly extended to include azimuthal variations due to forward flight and a simplified scheme for locating critical points where vortex elements are placed. A test case was obtained for validation of the predictions of induced velocity. Comparison of the results indicates that the code requires some more features before satisfactory predictions can be made over the whole rotor disk. Specifically, shed vorticity due to the azimuthal variation of blade loading must be incorporated into the model. Interactions between vortices shed from the four blades of the model rotor must be included. The Scully code for calculating the velocity field is being modified in parallel with these efforts to enable comparison with experimental data. To date, some comparisons with flow visualization data obtained at Georgia Tech were performed and show good agreement for the isolated rotor case. Comparison of time-resolved velocity data obtained at Georgia Tech also shows good agreement. Modifications are being implemented to enable generation of time-averaged results for comparison with NASA data.

Komerath, Narayanan M.↗
NASA NTRSDate not supplied

Cross-Validation of Computational and Experimental Distributed Surface Pressures on the Space Launch System

This paper presents a new workflow for comparing experimental pressure-sensitive paint (PSP) data to computational fluid dynamic (CFD) simulations by way of mapping data from corresponding grids utilizing interpolation methods. In addition to generating quantitative and qualitative point-to-point comparisons between PSP and CFD data, this workflow extracts sectional loading data from both grids and generates lineload comparison charts for corresponding PSP and CFD runs. Experimental PSP data presented in this paper were taken from a 2016 NASA Ames Research Center Unitary Plan Wind Tunnel 11- by 11-Foot Transonic WindTunnel Facility test of the NASA Space Launch System. CFD simulation data for comparison purposes were generated using the FUN3D code. Overall, interpolation onto PSP grids versus CFD grids yields comparable surface pressure fields. However, lineload comparisons are easier to make on the CFD grid-mapped data due to the grid topology and the current capabilities of the lineload analysis tools at NASA Langley Research Center. This workflow is written using contemporary software (Python, Tecplot, PyTecplot), is compatible with existing tools at NASA Langley, and is developed to be adaptable depending on the situation.

SLS↗
NASA NTRS1995

Off-design computer code for calculating the aerodynamic performance of axial-flow fans and compressors

An off-design axial-flow compressor code is presented and is available from COSMIC for predicting the aerodynamic performance maps of fans and compressors. Steady axisymmetric flow is assumed and the aerodynamic solution reduces to solving the two-dimensional flow field in the meridional plane. A streamline curvature method is used for calculating this flow-field outside the blade rows. This code allows for bleed flows and the first five stators can be reset for each rotational speed, capabilities which are necessary for large multistage compressors. The accuracy of the off-design performance predictions depend upon the validity of the flow loss and deviation correlation models. These empirical correlations for the flow loss and deviation are used to model the real flow effects and the off-design code will compute through small reverse flow regions. The input to this off-design code is fully described and a user's example case for a two-stage fan is included with complete input and output data sets. Also, a comparison of the off-design code predictions with experimental data is included which generally shows good agreement.

Schmidt, James F.↗
NASA NTRS1987

High speed simulation of flexible multibody dynamics

A multiflexible body dynamics code intended for fast turnaround control design trades is described. Nonlinear rigid body dynamics and linearized flexible dynamics combine to provide efficient solution of the equations of motion. Comparison with results from the DISCOS code provide verification of accuracy.

Jacot, A. D.↗
NASA NTRS1993

Navier-Stokes Computations and Experimental Comparisons for Multielement Airfoil Configurations

A two-dimensional unstructured Navier-Stokes code is utilized for computing the flow around multielement airfoil configurations. Comparisons are shown for a landing configuration with an advanced-technology flap. Grid convergence studies are conducted to assess inaccuracies caused by inadequate grid resolution. Although adequate resolution is obtained for determining the pressure distributions, further refinement is needed to sufficiently resolve the velocity profiles at high angles of attack. For the advanced flap configuration, comparisons of pressure distributions and lift are made with experimental data. Here, two flap riggings and two Reynolds numbers are considered. In general, the trends caused by variations in these quantities are well predicted by the computations, although the angle of attack for maximum lift is overpredicted.

Anderson, W. Kyle↗
NASA NTRS1981

Relations for the thermodynamic and transport properties in the testing environment of the Langley hypersonic CF4 tunnel

Thermodynamic and transport properties of gaseous CF4 that can be used in flow field computer codes and theoretical analyses for comparison of results with experimental data from the Langley Hypersonic CF4 Tunnel are presented. The thermodynamic relations which are based on thermally perfect but calorifically imperfect gas are adequate for the testing environment of the CF4 tunnel and are simpler to use than the imperfect gas relations required to define the complete expansion from the tunnel reservoir. Relations for the transport properties are based on the kinetic theory of gases in which published experimental data are used in the derivation of the relations. Extensive experimental data were located for viscosity and the derived relation should provide values for viscosity with errors of less than 1 percent. The experimental data for thermal conductivity were limited with significant disagreement between the various sources. The derived relation will probably provide values for the thermal conductivity with errors of no more than 5 percent which is within the accuracy of the experimental data.

Sutton, K.↗
NASA NTRS1984

Modeling material failure with a vectorized routine

The computational aspects of modelling material failure in structural wood members are presented with particular reference to vector processing aspects. Wood members are considered to be highly orthotropic, inhomogeneous, and discontinuous due to the complex microstructure of wood material and the presence of natural growth characteristics such as knots, cracks and cross grain in wood members. The simulation of strength behavior of wood members is accomplished through the use of a special purpose finite element/fracture mechanics routine, program STARW (Strength Analysis Routine for Wood). Program STARW employs quadratic finite elements combined with singular crack tip elements in a finite element mesh. Vector processing techniques are employed in mesh generation, stiffness matrix formation, simultaneous equation solution, and material failure calculations. The paper addresses these techniques along with the time and effort requirements needed to convert existing finite element code to a vectorized version. Comparisons in execution time between vectorized and nonvectorized routines are provided.

Cramer, S. M.↗