Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “casting”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Fabrication and Testing of Solid-Solution Strengthened Corrosion Resistant Alloys For Service in Molten Fluoride Environments

The demand for higher system thermal efficiencies requires the operation of power generation cycles and heat conversion systems at progressively higher temperatures. As the system operating temperature increases, existing materials may not provide adequate mechanical properties or environmental compatibility or both. There is an increasing commercial interest in the development and deployment of liquid-fueled Molten Salt Reactors (MSRs). Hastelloy®N, the highest performing candidate MSR structural alloy, is not capable of operations at temperatures above 700°C, thus limiting the performance of these systems. Using an Integrated Computational Materials Engineering (ICME)-approach and small laboratory scale heats, ORNL developed a class of patented alloys covered by U.S. Patent 9, 435, 011 B2, “Creep-resistant, Cobalt-free alloys for high temperature, liquid-salt heat exchanger systems,” similar to Hastelloy®N in that they are primarily solid solution strengthened. In contrast to precipitation strengthened alloys, the microstructure of solid solution alloys and hence the high temperature mechanical properties are stable for extended periods of time allowing long reactor operating life. The new alloys have shown to possess good resistance to liquid fluorides at temperatures up to 850°C and have significantly improved creep properties when compared to Hastelloy®N. The purpose of the CRADA project was for ORNL to collaborate with Haynes International- a materials producer, MetalTek International- a foundry, and Kairos Power – an advanced reactor developer – to scale-up selected alloys, evaluate their properties, and identify one solid solution strengthened alloy that can meet the property requirements for the reactor being developed by Kairos Power and other similar liquid fluoride-salt cooled reactors. As part of the project, eight alloys were down-selected and fabricated in larger industrial scale heats by Haynes International. Resistance to molten salt was evaluated in flowing FLiNaK and FLiBe by Kairos Power using their Rotating Cage Loop (RCL) system. Accounting for iron deposition during these tests, the new alloys displayed very low net mass change showing excellent corrosion performance in molten salt. Creep properties evaluated at ORNL were found to be better than that of Hastelloy®N and 316 stainless steel. Long-term stabilities of the alloys evaluated by Haynes International showed that these alloys have excellent thermal stability in the temperature range 704.4-815.6°C, with the change in strength and ductility being less than 10-15% after a 4000-hour exposure at 815.6°C. Autogenously Gas Tungsten Arc Welding (GTAW) welded samples showed less than 10% change in yield strength / ultimate tensile strength / total elongation compared to the basemetal, indicating that the alloys have excellent weldability. Three parts were successfully investment-cast using one alloy with very little voiding showing feasibility of fabricating parts using the casting process. This project enabled extensive interaction between the material producer Haynes International, casting supplier MetalTek, and reactor developer Kairos Power. This facilitated testing of materials and components produced using the newly developed alloys by the end-user. This allowed the generation of critical dataset required for down-selection of a few promising alloys for further development. This data is also currently being shared with other reactor designers for them to evaluate the suitability of this alloy for their reactor design. The availability of this alloy will ultimately enable the design and development and deployment of MSRs with increased temperature of operation and thus, improved efficiencies.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2025

Fabrication and Testing of Solid-Solution Strengthened Corrosion Resistant Alloys For Service in Molten Fluoride Environments

The demand for higher system thermal efficiencies requires the operation of power generation cycles and heat conversion systems at progressively higher temperatures. As the system operating temperature increases, existing materials may not provide adequate mechanical properties or environmental compatibility or both. There is an increasing commercial interest in the development and deployment of liquid-fueled Molten Salt Reactors (MSRs). Hastelloy®N, the highest performing candidate MSR structural alloy, is not capable of operations at temperatures above 700°C, thus limiting the performance of these systems. Using an Integrated Computational Materials Engineering (ICME)-approach and small laboratory scale heats, ORNL developed a class of patented alloys covered by U.S. Patent 9,435,011 B2, “Creep-resistant, Cobalt-free alloys for high temperature, liquid-salt heat exchanger systems,” similar to Hastelloy®N in that they are primarily solid solution strengthened. In contrast to precipitation strengthened alloys, the microstructure of solid solution alloys and hence the high temperature mechanical properties are stable for extended periods of time allowing long reactor operating life. The new alloys have shown to possess good resistance to liquid fluorides at temperatures up to 850°C and have significantly improved creep properties when compared to Hastelloy®N. The purpose of the CRADA project was for ORNL to collaborate with Haynes International- a materials producer, MetalTek International- a foundry, and Kairos Power – an advanced reactor developer – to scale-up selected alloys, evaluate their properties, and identify one solid solution strengthened alloy that can meet the property requirements for the reactor being developed by Kairos Power and other similar liquid fluoride-salt cooled reactors. As part of the project, eight alloys were down-selected and fabricated in larger industrial scale heats by Haynes International. Resistance to molten salt was evaluated in flowing FLiNaK and FLiBe by Kairos Power using their Rotating Cage Loop (RCL) system. Accounting for iron deposition during these tests, the new alloys displayed very low net mass change showing excellent corrosion performance in molten salt. Creep properties evaluated at ORNL were found to be better than that of Hastelloy®N and 316 stainless steel. Long-term stabilities of the alloys evaluated by Haynes International showed that these alloys have excellent thermal stability in the temperature range 704.4-815.6°C, with the change in strength and ductility being less than 10-15% after a 4000-hour exposure at 815.6°C. Autogenously Gas Tungsten Arc Welding (GTAW) welded samples showed less than 10% change in yield strength / ultimate tensile strength / total elongation compared to the basemetal, indicating that the alloys have excellent weldability. Three parts were successfully investment-cast using one alloy with very little voiding showing feasibility of fabricating parts using the casting process. This project enabled extensive interaction between the material producer Haynes International, casting supplier MetalTek, and reactor developer Kairos Power. This facilitated testing of materials and components produced using the newly developed alloys by the end-user. This allowed the generation of critical dataset required for down-selection of a few promising alloys for further development. This data is also currently being shared with other reactor designers for them to evaluate the suitability of this alloy for their reactor design. The availability of this alloy will ultimately enable the design and development and deployment of MSRs with increased temperature of operation and thus, improved efficiencies.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Enabling Bipolar Membrane Manufacturing Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Enabling Roll-to-Roll Manufacturing of Bipolar Membranes Using Microscopy

Bipolar membranes (BPMs) used for water treatment suffer from interface instabilities, causing premature failure and decreased performance. Recent research has highlighted the impacts of membrane morphology on mechanical behavior and performance. Improved material performance of thin film membranes requires enhanced transport properties coupled with better control of the mechanical characteristics to avoid premature failure of the film. Thus, morphology is a key parameter when developing and evaluating novel membrane materials. Microscopy offers unique advantages for nano-scale characterization of thin film membrane interfaces and morphologies. In this study, the interface junction of BPMs was evaluated using scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). BPMs were fabricated using (1) hot pressing lamination, (2) bench-scale solution casting, and (3) roll-to-roll sequential casting (R2R). Both commercial and in-house fabricated ion exchange membranes were used in the BPMs. The BPMs were comprised of a cation exchange membrane and an anion exchange membrane with a catalyst layer sandwiched in between. Cross sectional SEM and EDX images of the membrane interface junction were compared among the different fabrication techniques and materials. The bench cast catalyst layers were nonuniform compared to the R2R and hot pressed membranes, demonstrating the importance of precise catalyst application conditions. Different thicknesses of the BPMs and individual membrane layers revealed that polymer solution concentration needs to be optimized during manufacturing. This work shows that microscopy can identify key processing parameters that affect BPM interface junction quality at the microscale to enable manufacturing of high performance BPMs.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Water soluble barrier coatings for washout tooling for a composite layup

A washout tooling for a composite layup is provided. The washout tooling comprises a casting mold having an exterior surface. The casting mold comprises a particulate material and a water-soluble binder. The casting mold is adapted to break down in the presence of an aqueous solution. The washout tooling further comprises a water-soluble coating layer overlying the exterior surface. The water-soluble coating layer is adapted to break down in the presence of an aqueous solution. The washout tooling further comprises a curable composite layer overlying the water-soluble coating layer. The water-soluble coating layer minimizes contact between the particulate material and the curable composite layer.

Saito, Tomonori↗
DOE OSTI2025

Wire Arc Additive Manufacturing of Multi-material Parts Using H-13 Tool Steel

H-13 tools steel’s relative hardness, resistance to thermal fatigue, and high tolerance of thermal shock, make it very desirable for use in forging, pressing, casting, and extrusion processes[1]. H-13 is however typically quite expensive when compared to many other steel compositions. It is therefore desirable to encase a lower cost steel composition with H-13. This configuration allows for the benefits of H-13 tooling to be realized, at a considerably reduced cost. To demonstrate the viability of this concept, a casting tool was fabricated using a Wire Arc Additive Manufacturing (WAAM) process. Initial materials testing was conducted on a multi-material wall which consisted of one section of H-13 tool steel, and one section of 410NiNmo. These tests included scanning electron microscopy, energy dispersive X-ray spectroscopy, and hardness testing. This testing generated favorable results and subsequently a casting tool was fabricated for evaluation. Utilization of a Multi-Material WAAM process to fabricate large tooling in this manner could yield significant improvements in material cost, manufacturing agility, and supply chain complexity.

Lambert, Nathan [ORNL] (ORCID:0009000324134206)↗
DOE OSTI2020

High Speed In-situ X-ray Imaging of 3D Freeze Printing of Aerogels

3D freeze printing (3DFP) combines drop-on-demand (DOD) inkjet printing with freeze casting to fabricate lightweight and multifunctional aerogels with customized geometries. Freeze casting is an efficient and easily implemented method capable of fabricating porous, sponge-like structures for many different applications. This process enables tailoring the microstructure of the final product (i.e., pore morphology, alignment, average size distribution, etc.) by controlling the fabrication conditions and freezing kinetics. Furthermore, its combination with DOD printing provides the capability of engineering the macrostructure without relying on a mold as reported for 3D freeze-printed aerogels made from graphene, silver nanowires, and other nanocomposites. In this paper, we performed in-situ X-ray imaging to understand the inside process dynamics in 3DFP using a commercially available colloidal silica ink. We investigated the 3DFP process with the following hierarchy: first, single droplets; then, uniform lines obtained from coalescence of droplets; and finally, three consecutive lines deposited layer by layer. With the help of X-ray imaging, the importance of the balance between material deposition and freezing rates was shown in-situ by the observation inside of the freeze front following the tip of the printed line. The effects of the substrate temperature on the elimination of undesired interfacial boundaries were also shown by the observed ice crystals penetrating from lower to upper layer.

36 MATERIALS SCIENCE↗
DOE OSTI2022

High-performance organic photodetectors enabled by a refined fibrillar multiphase morphology

Film morphology of donor:acceptor blend layers plays a critical role in photon-to-current efficiency and dark/noise current of organic photodetectors (OPDs). One effective approach to manipulate crystallization and mesoscale phase separation of such blend layers is sequential casting (SC). However, the guiding strategies to control the morphology and the impacts on OPD performance of the SC films remain elusive, as the film structural evolution during SC is different from conventional blend casting (BC). In this report a refined fibrillar multiphase morphology is demonstrated by SC in an NT812:IEICO-4F blend film, where the high-quality IEICO-4F crystallites infiltrate the robust NT812 fibril network from the surface to the bulk. Such a morphology leads to improved charge generation and collection, reduced trap states, and enhanced charge block capability of resultant device, enabling simultaneous achievement of high external quantum efficiency and low dark/noise current. A maximum special detectivity of 5 × 10 13 Jones is achieved at 860 nm under –0.1 V, which is among the highest detectivities for vis-to-NIR OPDs. The linear dynamic range and response speed are also improved. Such enhancements are parallelly observed from OPD devices based on other blend systems with similar fibrillar refinement, which provides guidelines for film structure manipulation towards high OPD performance.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Hierarchical microstructural parameters governing electrical and thermal conductivity in Al-based eutectic systems

Enhancing conductivity properties of aluminum alloys can drive superior performance and efficiency across diverse engineering applications, yet currently commercially available Al casting alloys are severely limited in electrical and thermal conductivity. There is a general understanding that the presence of any defects and alloying elements within Al will inevitably lower conductivity properties. However, there is a lack of comparative studies evaluating the intricate interplay between the microstructural parameters and conductivity properties across cast Al-based eutectic systems. Therefore, this study bridges this gap by conducting a comparative study across hypoeutectic alloy compositions consisting of 50 % primary Al and 50 % eutectic region to elucidate the key parameters that dictate conductivity properties. This research contributes to advancing the understanding of alloy design opportunities for high conductivity, high strength castable Al alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Bicontinuous substrates with reduced pore restriction for CO 2 -selective composite membranes

A substrate with bicontinuous structure is attractive for thin-film composite (TFC) membrane synthesis due to its high surface porosity and well-interconnected bulk morphology. In this study, the vapor-induced phase separation (VIPS) of the casting solution comprising water, 2-pyrrolidone, and polyethersulfone (PES) was studied. By tuning the water addition in the casting solution and water vapor exposure time, the optimized substrate exhibited a bicontinuous surface with a high porosity of 24.2% (or 216/µm 2 pore density), thereby mitigating pore restriction and showing a high CO 2 permeance of 2.94×10 5 GPU. Compared to the benchmark PES substrate with cellular surface pores and lower gas permeance, the use of the bicontinuous substrate led to a 12% increase in the CO 2 permeance of the TFC membrane. The mitigated pore restriction was further rationalized by a resistance-in-series model. The analysis of the lateral diffusion and substrate resistances indicates that an even higher surface pore density of the substrate is required to fully realize the potential of ultra-permeable, CO 2 -selective polymers in the TFC configuration. As a result, the scalability of the VIPS process was demonstrated by the roll-to-roll fabrication of the optimized bicontinuous substrate with a width of 21" and a length of >100'.

42 ENGINEERING↗
DOE OSTI2023

Bone resorption and formation in the pedicles of European roe deer ( Capreolus capreolus ) in relation to the antler cycle—A morphological and microanalytical study

We analyzed pedicle bone from roe bucks that had died around antler casting or shortly before or during the rutting period. Pedicles obtained around antler casting were highly porous and showed signs of intense osteoclastic activity that had caused the formation of an abscission line. Following the detachment of the antler plus a portion of pedicle bone, osteoclastic activity in the pedicles continued for some time, and new bone was deposited onto the separation plane of the pedicle stump, leading to partial pedicle restoration. Pedicles obtained around the rutting period were compact structures. The newly formed, often very large secondary osteons, which had filled the resorption cavities, exhibited a lower mineral density than the persisting older bone. The middle zones of the lamellar infilling frequently showed hypomineralized lamellae and enlarged osteocyte lacunae. This indicates a deficiency in mineral elements during the formation of these zones that occurred along with peak antler mineralization. We suggest that growing antlers and compacting pedicles compete for mineral elements, with the rapidly growing antlers being the more effective sinks. The competition between the two simultaneously mineralizing structures is probably more severe in Capreolus capreolus than in other cervids. This is because roe bucks regrow their antlers during late autumn and winter, a period of limited food and associated mineral supply. The pedicle is a heavily remodeled bone structure with distinct seasonal variation in porosity. Pedicle remodeling differs in several aspects from the normal bone remodeling process in the mammalian skeleton.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2020

Phase Transformation of Thermally Aged and Neutron Irradiated Duplex Stainless Steel Used in LWRs. Final report

The lifetime of reactor components made of duplex stainless steels can be limited by the embrittlement from thermal aging, neutron irradiation or a synergistic effect between thermal aging and neutron irradiation. There is still a large scientific knowledge gap in understanding the phase evolution in duplex stainless steels upon thermal aging with or without neutron irradiation, the synergistic effect between thermal aging and neutron irradiation, and the impacts of structural evolution on material mechanical responses. In this project, totally, five major tasks were completed through this project: a) the in-situ WAXS tensile tests of thermally aged cast duplex stainless steels, b) the EXAFS investigation of thermally aged cast austenitic stainless steel and welds of austenite sainless steel, c) the characterization of irradiation effect on neutron irradiated CASS using APT, d) characterize the ferrite hardening of neutron irradiated CASS using nanoindentation, and e) the FEM modelling to validate the in-situ WAXS tensile tests and to simulate the stress/strain distribution during deformation for thermally aged duplex stainless steel. In summary, the thermal aging without neutron irradiation can significantly increase the strength of ferrite phase through the spinodal decomposition and G-phase precipitations. The in-situ X-ray experiments show that the hardening effect in ferrite phase can significantly alter the load partition between the ferrite and austenite phases. Atom probe tomography characterizations on samples irradiated to 0.08, 3, 5, 10, 20, and 40 dpa shows that neutron irradiation has dominated the microstructural evolution after 3 dpa, and the spinodal decomposition has saturated yet even at 40 dpa based on the quantified wavelength and amplitude.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Remaining Life Determination

This project developed and demonstrated the capability of nondestructive evaluation methods for detecting early stage fatigue damage in grey cast iron metal. Non-collinear ultrasonic wave mixing and laser speckle differentiation were the primary technologies evaluated on custom fatigue specimens having properties specified by Caterpillar, Inc. The ultrasonic method showed the greatest potential for estimating the remaining fatigue life in grey cast iron, which may provide remanufacturers with a level of confidence when fielding used component cores in high-stress applications. While successes were realized during this project, there are still follow-on research tasks required to prove the commercial applicability of the methods. The following report sections document the steps completed during the project and an assessment of the technologies applied.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Optimizing Information Automation Using a New Method Based on System-Theoretic Process Analysis: Tool Development and Method Evaluation

This report is an update to a prior report that describes progress and findings for a program of research supporting the design and optimization of information automation systems for nuclear power plants. Much of the domestic nuclear fleet is currently focused on modernizing technologies and processes, including transitioning toward digitalization in the control room and throughout the plant, along with a greater interest in the use of automation, artificial intelligence, robotics, and other emerging technologies. While there are significant opportunities to apply these technologies toward greater plant safety, efficiency, and overall cost-effectiveness, optimizing their design and avoiding potential safety and performance risks depends on ensuring that human performance-related organizational and technical design issues are identified and addressed early in the design process. This report describes modeling tools and techniques, based on sociotechnical systems theory, to support these design goals and their application in the current research effort. The report is primarily intended for senior nuclear energy stakeholders, including regulators, corporate management, and senior plant management. We have developed and employed a method to design an optimized information automation ecosystem (IAE) based on the systems-theoretic constructs underlying sociotechnical systems theory in general and the Systems-Theoretic Accident Modeling and Processes (STAMP) approach in particular. We argue that an IAE can be modeled as an interactive information control system whose behavior can be understood in terms of dynamic control, feedback, and communication relationships amongst the system’s technical and organizational components. We have employed two STAMP-based tools in this effort. The first is Causal Analysis based on STAMP (CAST), an accident and incident analysis technique that was used to examine a performance- and safety-related incident at an industry partner’s plant involving the unintentional activation of an emergency diesel generator. This analysis provided insight into the behavior of the plant’s current information control structure within the context of a specific, significant event. The second tool is Systems Theoretic Process Analysis (STPA) which is a proactive risk analysis tool used to examine existing and potential, planned sociotechnical systems. STPA was used to identify risk factors in the current design of a generic nuclear power plant (NPP) preventive maintenance system. Our analyses focused on identifying near-term system improvements and longer-term design requirements for an optimized IAE system. CAST analysis findings indicate an important underlying contributor to the incident under investigation, and a significant risk to information automation system performance, was perceived time and schedule pressure, which exposed weaknesses in interdepartmental coordination between and within responsible plant organizations and challenged the resilience of established plant processes, until a human caused the eventual event. These findings are discussed in terms of their risk to overall system performance and their implications for information automation system resilience and brittleness. STPA findings exposed several areas of concern in the design of current preventive maintenance systems. We also present two preliminary information automation models. The proactive issue resolution (PIR) model is a test case of an information automation concept with significant near-term potential for application and subsequent reduction in significant plant events. The IAE model is a more general representation of a broader, plantwide information automation system and represents an end-state vision for our work. From our results, we have generated an initial set of preliminary system-level requirements and safety constraints for these models. We have also focused on early development of easy to learn, easy to use “transportable” tools for sociotechnical systems analysis. We intend these to be used by NPP personnel as a means of gaining reliable and relatively quick insight into (1) sociotechnical systems factors impacting incidents and accidents, (2) potential sociotechnical risk factors in existing or planned system designs, and (3) potential weaknesses in a system’s safety and/or information control structure. We conclude the report with a set of summary recommendations, a discussion of planned and potential follow-on research and development, and a draft list of system-level requirements and safety constraints for optimized information automation systems.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

Grain Refinement Effect on the Hot-Tearing Resistance of Higher-Temperature Al–Cu–Mn–Zr Alloys

The hot-tearing resistance of Al-Cu-Mn-Zr (ACMZ) alloys was investigated as a step toward introducing these new cast alloys for severe duty, higher-temperature applications, such as cylinder heads for down-sized, turbocharged automotive engines. Alloy Cu compositions were varied from 5 to 8 wt.%. Targeted Ti levels were 0.02, 0.1, and 0.2 wt.% via additions of the Al–5Ti–1B master alloy. Hot-tearing resistance was assessed by visual examination and ranking of the cracking severity in a multi-arm permanent mold casting. It was found that at high impurity contents (Fe and Si of 0.2 wt.% each), the Al–Cu–Mn–Zr alloy with 4.95 wt.% Cu exhibited the poorest hot-tearing resistance, irrespective of the grain refining amount. Microstructural analysis indicated an effective reduction in the grain size, as the Ti additions were increased to 0.02 and 0.1 wt.% Ti via the Al–Ti–B grain refiner. The finest grain size was attained with a 0.1 wt.% Ti. Based on the hot-tearing evaluation, it was found that the additional grain refining via the Al–5Ti–1B master alloy at 0.1 wt.% Ti significantly reduces the hot-tearing susceptibility at Cu contents greater than 7.3 wt.% for ACMZ alloys with low Fe and Si. These findings indicate that the best hot-tearing resistance was observed at a grain refiner level of 0.1 wt.% Ti and high Cu content (greater than 7.3 wt.%). This study to indicates that these Al–Cu–Mn–Zr alloys, which possess excellent microstructural stability and mechanical properties at elevated temperatures, can also possess excellent hot-tearing resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Compositional Modifications to Alter and Suppress Laves Phases in Al x CrMoTa y Ti Alloys

The development of refractory complex concentrated alloys in the Al–Cr–Mo–Ta–Ti alloy system is reported. Alloys with modified Al and Ta concentrations are designed using CALPHAD tools and produced via arc melting and characterized in both as-cast and annealed forms. Properties of the alloys, nature of the microstructures, and phase transformation behavior are described via X-ray diffraction, microstructural characterization, microhardness, and differential scanning calorimetry. Two alloys, namely, Al 0.25 CrMoTa 0.8 Ti and Al 0.75 CrMoTa 0.8 Ti, are represented by a body-centered-cubic matrix phase after annealing, along with a secondary Cr–Ta Laves phase of the C15 and C14 polytypes, respectively. In as-cast and annealed forms, the Al 0.75 CrMoTa 0.45 Ti alloy comprises a single-bcc phase. Microhardness of the Laves phase containing alloys demonstrates susceptibility to cracking, whereas the Al 0.75 CrMoTa 0.45 Ti alloy displays high specific hardness, signs of ductility as evidenced by slip traces near indentations, and minimal scatter of hardness values.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Strong‐Yet‐Ductile Eutectic Alloys Employing Cocoon‐Like Nanometer‐Sized Dislocation Cells

Abstract Eutectic alloys (EAs) with superior fluidity are known to be the easiest to cast into high‐quality ingots, making them the alloys of choice for making large‐sized structural parts. However, conventional EAs (CEAs) have never reached strength–ductility combinations on par with the best in other alloy categories. Via thermomechanical processing of cast Ni‐32.88wt%Fe‐9.53wt%Al CEAs, a cocoon‐like nano‐meshed (as fine as 26 nm) network of dislocations (CNN‐D) is produced via recovery annealing, through the rearrangement of cold‐work‐accumulated dislocations anchored by dense pre‐existing nanoprecipitates. In lieu of traditional plasticity mechanisms, such as TWIP and TRIP, the CNN‐D is particularly effective in eutectic lamellae with alternating phases, as it instigates nanometer‐spaced planar slip bands that not only dynamically refine the microstructure but also transmit from the FCC (face‐centered‐cubic) layers into the otherwise brittle B2 layers. These additional mechanisms for strengthening and strain hardening sustain stable tensile flow, resulting in a striking elevation of both strength and ductility to outrank not only all previous CEAs, but also the state of the art—additively manufactured eutectic high‐entropy alloys. The CNN‐D thus adds a novel microstructural strategy for performance enhancement, especially for compositionally complex alloys that increasingly make use of nanoprecipitates or local chemical order.

Chemistry↗
DOE OSTI2020

Achieving Balanced Crystallization Kinetics of Donor and Acceptor by Sequential-Blade Coated Double Bulk Heterojunction Organic Solar Cells

Sequential deposition has great potential to achieve high performance in organic solar cells due to the resulting well-controlled vertical phase separation. In this work, double bulk heterojunction organic solar cells are fabricated by sequential-blade cast in ambient conditions. Probed by the in situ grazing incidence X-ray diffraction and in situ UV–vis absorption measurements, the seq-blade system exhibits a different tendency from each of the binary films during the film formation process. Due to the extensive aggregation of FOIC, the binary PBDB-T:FOIC film displays a strong and large phase separation, resulting in low current density (J sc) and unsatisfactory power conversion efficiency. In the seq-blade cast system, the bottom layer PBDB-T:IT-M produces many crystal nuclei for the top layer PBDB-T:FOIC, so the PBDB-T molecules are able to crystallize easily and quickly. Balanced crystallization kinetics between polymer and small molecule and an ideal percolation network in the film are observed. In addition, the balanced crystallization kinetics are favorable toward realizing lower recombination loss through charge transport processes.

14 SOLAR ENERGY↗