Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “capacity loss”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Porous Plug Phase Separator and Superfluid Film Flow Suppression System for the Soft X-Ray Spectrometer Onboard Hitomi

When using superfluid helium in low gravity environments, porous plug phase separators are commonly used to vent boiloff gas while confining the bulk liquid to the tank. Invariably, there is a flow of superfluid film from the perimeter of the porous plug down the vent line. For the Soft X-ray Spectrometer onboard ASTRO-H (Hitomi), its approximately 30-liter helium supply has a lifetime requirement of more than 3 years. A nominal vent rate is estimated as ~ 30 ug/s, equivalent to ~ 0.7 mW heat load. It is therefore critical to suppress any film flow whose evaporation would not provide direct cooling of the remaining liquid helium. That is, the porous plug vent system must be designed to both minimize film flow and to ensure maximum extraction of latent heat from the film. The design goal for Hitomi is to reduce the film flow losses to <2 ug/s, corresponding to a loss of cooling capacity of <40 uW. The design adopts the same general design as implemented for Astro-E and E2, using a vent system composed of a porous plug, combined with an orifice, a heat exchanger, and knife-edge devices. In this paper, design, on-ground testing results and in-orbit performance are described.

Porous↗
NASA NTRS2021

NASA Engineering and Safety Center Technical Bulletin No. 21-05: Industry Recommendations from Arecibo Observatory Zinc Spelter Socket Joint Failure Analysis

A structural analysis and forensic investigation concluded that the Arecibo Observatory M4N socket joint failure in August 2020 was primarily due to cumulative damage caused by initially low structural design margins and a high percentage of sustained load, resulting in zinc creep deformation, progressive internal socket wire damage, and eventual loss of joint capacity. Open spelter sockets of this type are used throughout industry in stay cables. Recommendations are proposed to prevent failures of similar socket joints, including verification of positive stress margins in socket joint wires for all failure modes, periodic visual inspections with pass/fail criteria for zinc extrusion that are tied to structural qualification, and revisiting codes/ industry standards to capture lessons learned.

Arecibo Observatory↗
DOE OSTI2025

Ether Cleavage Decreases the Ion Exchange Capacity of Anion Exchange Membranes

Anion exchange membranes (AEMs) are integral to fuel cells and water electrolysis systems but suffer from poor durability under alkaline conditions. Ether cleavage is an important failure pathway of poly(arylene ether)-based AEMs that compromises both mechanical stability and ion transport. While this degradation pathway is often studied in terms of polymer fragmentation, the role of newly formed hydrophilic groups has been largely overlooked. Here, we show that polymer scission leads to reduced mechanical rigidity, while the introduction of hydrophilic groups partially mitigates this loss. Under alkaline conditions, phenoxide groups formed during ether cleavage neutralize the polymer cations, leading to a previously unreported loss of ion exchange capacity (IEC). This IEC loss mechanism exacerbates the reduction in ionic conductivity, emphasizing the severity of ether cleavage as a degradation pathway. Recognizing that ether cleavage introduces significant chemical changes beyond polymer fragmentation provides critical insights into its interplay with other degradation mechanisms, such as the direct reduction of cationic sites by E2 and S N 2, and provides molecular-level interpretations for the concurrent effects of polymer scission and increased hydrophilicity on membrane performance.

crystal cleavage↗
NASA NTRS1991

The International Space University's variable gravity research facility design

A manned mission to Mars will require long travel times between Earth and Mars. However, exposure to long-duration zero gravity is known to be harmful to the human body. Some of the harmful effects are loss of heart and lung capacity, inability to stand upright, muscular weakness and loss of bone calcium. A variable gravity research facility (VGRF) that would be placed in low Earth orbit (LEO) was designed by students of the International Space University 1989 Summer Session held in Strasbourg, France, to provide a testbed for conducting experiments in the life and physical sciences in preparation for a mission to Mars. This design exercise was unique because it addressed all aspects concerning a large space project. The VGRF design was described which was developed by international participants specializing in the following areas: the politics of international cooperation, engineering, architecture, in-space physiology, material and life science experimentation, data communications, business, and management.

Bailey, Sheila G.↗
DOE OSTI2021

Quantification of heterogeneous, irreversible lithium plating in extreme fast charging of lithium-ion batteries

Realization of extreme fast charging (XFC, ≤15 minutes) of lithium-ion batteries is imperative for the widespread adoption of electric vehicles. However, dramatic capacity fading is associated with XFC, limiting its implementation. To quantitatively elucidate the effects of irreversible lithium plating and other degradation mechanisms on the cell capacity, it is important to understand the links between lithium plating and cell degradation at both the local and global (over the full cell) scales. Here, we study the nature of local lithium plating after hundreds of XFC cycles (charging C-rates ranging from 4C to 9C) in industrially-relevant pouch cells using spatially resolved X-ray diffraction. Our results reveal a spatial correlation at the mm scale between irreversible lithium plating on the anode, inactive lithiated graphite phases, and local state-of-charge of the cathode. In regions of plated lithium, additional lithium is locally and irreversibly trapped as lithiated graphite, contributing to the loss of lithium inventory (LLI) and to a local loss of active anode material. The total LLI in the cell from irreversibly plated lithium is linearly correlated to the capacity loss in the batteries after XFC cycling, with a non-zero offset originating from other parasitic side reactions. Finally, at the global (cell) scale, LLI drives the capacity fade, rather than electrode degradation. We anticipate that the understanding of lithium plating and other degradation mechanisms during XFC gained in this work will help lead to new approaches towards designing high-rate batteries in which irreversible lithium plating is minimized.

25 ENERGY STORAGE↗
DOE OSTI2026

Impact of anion-exchange membrane degradation on long-term CO 2 electrolysis to ethylene

Electrochemical CO 2 reduction (eCO2R) to ethylene offers a unique opportunity to diversify domestic supply chains for chemical manufacturing. Large-scale deployment of eCO2R to ethylene reactors is currently limited by low energy efficiencies and poor durability. Herein, we demonstrate >100 h of continuous electrolysis at an industrially relevant current density of 200 mA cm −2 in a 25 cm 2 geometric area zero-gap reactor with a full-cell voltage <3.1 V and ethylene Faradaic efficiency >30%. Incorporating expanded polytetrafluoroethylene (PTFE)-supported electrodes into zero-gap reactors allows for durable electrode catalysts that are resistant to flooding, and this enables wider ranges of operating parameters not typically accessible in CO 2 electrolysis. Finally, we identify membrane degradation, evidenced by a loss of membrane ion-exchange capacity, as the leading cause of performance loss over 144 h of electrolysis.

Energy - Conversion↗
DOE OSTI2023

Critical Contribution of Imbalanced Charge Loss to Performance Deterioration of Si-Based Lithium-Ion Cells during Calendar Aging

Increasing the energy density of lithium-ion batteries, and thereby reducing costs, is a major target for industry and academic research. One of the best opportunities is to replace the traditional graphite anode with a high-capacity anode material, such as silicon. However, Si-based lithium-ion batteries have been widely reported to suffer from a limited calendar life for automobile applications. Heretofore, there lacks a fundamental understanding of calendar aging for rationally developing mitigation strategies. Both open-circuit voltage and voltage-hold aging protocols were utilized to characterize the aging behavior of Si-based cells. Particularly, a high-precision leakage current measurement was applied to quantitatively measure the rate of parasitic reactions at the electrode/electrolyte interface. The rate of parasitic reactions at the Si anode was found 5 times and 15 times faster than those of LiNi 0.8 Mn 0.1 Co 0.1 O 2 and LiFePO 4 cathodes, respectively. Here, the imbalanced charge loss from parasitic reactions plays a critical role in exacerbating performance deterioration. In addition, a linear relationship between capacity loss and charge consumption from parasitic reactions provides fundamental support to assess calendar life through voltage-hold tests. These new findings imply that longer calendar life can be achieved by suppressing parasitic reactions at the Si anode to balance charge consumption during calendar aging.

25 ENERGY STORAGE↗
DOE OSTI2024

Electrolyte and Cutoff Potential Effects on Cycle Life of Li4Ti5O12/LiNi0.9Mn0.1O2 Batteries for Behind-the-Meter Storage Applications

Behind-the-Meter Storage (BTMS) is a stationary battery energy storage system that is connected to the electrical distribution system on the customer's side of the utility's service meter. BTMS systems are used to store electrical energy from the grid as well as inconstant, renewable energy, such as local solar and wind generation. A successful BTMS system will allow the customer to pair their energy generation and storage to optimize electrical consumption from the grid, improving reliability and minimizing cost. For BTMS applications, batteries must be designed and optimized with different set of criteria from other leading segments of the Li-ion battery market, like transportation, due the system being stationary and proximal to the residential or commercial building it's benefitting. BTMS applications prioritize safety, cost (low/no-critical materials), reliability (20-year calendar life), and durability (10,000 cycle life), while having the ability to (minimally) compromise energy density and rate capability. Lithium titanate (Li4Ti5O12-, LTO) is a promising anode candidate for BTMS applications due to its high safety and capacity retention, while maintaining a reasonable 160 mAhg-1 reversable capacity and composition of relatively abundant materials. (1) Specifically, LTO has a high working voltage which helps to prevent Li dendrite formation, improving safety. Furthermore, LTO also has negligible lithiation-based volume change, leading to less mechanical pulverization, or loss of active material, upon cycling. For the cathode, materials with little or no Co are of high interest due to the high cost and low abundance of Co. LiMn2O4 (LMO) has been paired with LTO for BTMS applications in the past due to its safety, low cost (abundancy), and reasonably high operating voltage. (2-4) However, the low capacity of LMO limits energy density and specific energy. While not the highest priority for BTMS applications, increasing energy density will enable deployment in space constrained BTMS applications and decrease total cost. LiNi0.9Mn0.1O2 (LN-MO) is a recently developed material with promise due to its high operating voltage and relatively low price. (5) However, Ni-rich layered oxides, including LNMO, tend to struggle with capacity retention during high-voltage cycling due to mechanical pulverization, irreversible phase transitions, and unstable solid-electrolyte interphase. The study presented here focuses on building an understanding of how electrolyte solvent and varied cutoff potentials will impact the cycle life of LTO/LN-MO cells. Specifically, a comparison is provided between ethylene carbonate (EC), ethyl methyl carbonate (EMC), fluoroethylene carbonate (FEC), and Gen2 electrolyte solvents with 1M Lithium hexafluorophosphate (LiPF6) salt, cycling to two upper termination potentials, 2.6V and 2.7V. Electrochemical testing and diagnostics (e.g., differential capacity analysis, area specific impedance, constant voltage hold, and rate capability) and post-mortem characterization will be used to understand the aging behavior and failure mechanisms of the 8 cell combinations (four electrolytes and two voltage cutoffs). Cells with FEC electrolyte showed a lower initial capacity compared to cells with Gen2, EMC, and EC cycling at both voltages; however, the cells with FEC showed consistent trends in capacity retention with 2.6V and 2.7V termination potentials, while the cells with the other electrolytes showed much higher rates of capacity loss when cycling to the higher voltage. These results indicate that FEC may play a role in improving durability of high-voltage, Ni-rich electrode systems for use in high-cycle applications, such as BTMS.

electrolyte↗
DOE OSTI2022

Composition Dependent Electrochemical Properties of Earth-Abundant Ternary Nitride Anodes

Growing energy storage demands on lithium-ion batteries necessitate exploration of new electrochemical materials as next-generation battery electrode materials. In this work, we investigate the previously unexplored electrochemical properties of earth-abundant and tunable Zn 1-x Sn 1+x N 2 (x = -0.4 to x = 0.4) thin films, which show high electrical conductivity and high gravimetric capacity for Li insertion. Enhanced cycling performance is achieved compared to previously published end-members Zn 3 N 2 and Sn 3 N 4 , showing decreased irreversible loss and increased total capacity and cycle stability. The average reversible capacity observed is >1050 mAh/g for all compositions and 1220 mAh/g for Zn-poor (x = 0.2) films. Extremely Zn-rich films (x = -0.4) show improved adhesion; however, Zn-rich films undergo a phase transformation on the first cycle. Zn-poor and stoichiometric films do not exhibit significant phase transformations which often plague nitride materials and show no required overpotential at the 0.5 V plateau. Cation composition x is explored as a mechanism for tuning relevant mechanical and electrochemical properties, such as capacity, overpotential, phase transformation, electrical conductivity, and adhesion. The lithiation/delithiation experiments confirm the reversible electrochemical reactions. Without any binding additives, the as-deposited electrodes delaminate resulting in fast capacity degradation. We demonstrate the mechanical nature of this degradation through decreased electrode thinning, resulting in cells with improved cycling stability due to increased mechanical stability. Combining composition and electrochemical analysis, this work demonstrates for the first time composition dependent electrochemical properties for the ternary Zn 1-x Sn 1+x N 2 and proposes earth-abundant ternary nitride anodes for increased reversible capacity and cycling stability.

25 ENERGY STORAGE↗
DOE OSTI2022

Li 8 MnO 6 : A Novel Cathode Material with Only Anionic Redox

In Li-excess transition-metal-oxide cathode materials, anionic oxygen redox can offer high capacity and high voltages, although peroxo and superoxo species may cause oxygen loss, poor cycling performance, and capacity fading. Previous work showed that undesirable formation of peroxide and superoxide bonds is controlled to some extent by Mn substitution, and the present work uses density functional calculations to examine the reasons for this by studying the anionic redox mechanism Li 8 MnO 6 . This material is obtained by substituting Mn for Sn in Li 8 SnO 6 or for Zr in Li 8 ZrO 6 , and we also compare to previous work on those materials. The calculations predict that Li 8 MnO 6 is stable at room temperature (with a band gap of 3.19 eV as calculated HSE06 and 1.82 eV as calculated with the less reliable with PBE+U), and they elucidate the chemical and structural effects involved in the inhibition of oxygen release in this cathode. Throughout the whole delithiation process, only O 2- ions are oxidized. The directional Mn-O bonds formed from unfilled 3d orbitals effectively inhibit the formation of O-O bonds, and the layered structure is maintained even after removing 3 Li per Li 8 MnO 6 formula unit. The calculated average voltage for removal of 3 Li is 3.69 V by HSE06, and the corresponding capacity is 389 mAh/g. The high voltage of oxygen anionic redox and the high capacity result in a high energy density of 1436 Wh/kg. The Li-ion diffusion barrier for the dominant interlayer diffusion path along the c-axis is 0.57 eV by PBE+U. Finally, these results help us to understand the oxygen redox mechanism in a new lithium-rich Li 8 MnO 6 cathode material and contribute to the design of high-energy-density lithium-ion-battery cathode materials with favorable electrochemical properties based on anionic oxygen redox.

Li8MnO6↗
DOE OSTI2023

Effects of SO 2 poisoning and regeneration on spinel containing CH 4 oxidation catalysts

Methane oxidation under periodic conditions and the oxygen storage capacity of a bilayer Pt/Pd/Al 2 O 3 over a Mn 0.5 Fe 2.5 O 4 spinel catalyst were studied before and after SO 2 exposure, and after simulated regeneration conditions. Prior to sulfur exposure, improvement in CH 4 oxidation conversion under periodic conditions compared to steady-state conditions was observed. After sulfur exposure at 100 °C, there was a loss in CH 4 oxidation performance and a loss of oxygen storage capacity of the spinel material. Here, the extent of regeneration from sulfur poisoning depends on the ability to induce the decomposition of sulfate species, and while all regeneration methods tested in this study did improve CH 4 conversion, regeneration methods under periodic conditions induced greater sulfur species desorption from the catalyst surface leading to improved CH 4 con version. Key regeneration parameters – temperature, feed composition, modulation amplitude and frequency – were optimized to induce S species decomposition and correlated to CH 4 oxidation activity recovery.

03 NATURAL GAS↗
DOE OSTI2025

Lithium-Ion Batteries with Lithium Manganese Iron Phosphate Cathodes and Lithium Titanate Anodes: Linking Electrode Dynamics to Cell Performance

This study examines the electrochemical performance, impedance behavior, and aging mechanisms of lithium-ion cells pairing lithium manganese iron phosphate (LiMn 0.6 Fe 0.4 PO 4 , LMFP64) cathodes with lithium titanate (Li 4 Ti 5 O 12 , LTO) anodes. LMFP64 half-cells display distinct Fe and Mn redox plateaus at ∼3.5 and ∼4.1 V, respectively, and deliver excellent rate capability. Three-electrode measurements show that LMFP64 dominates cell impedance, which changes sharply across the Fe–Mn redox transition and decreases with increasing temperature (30 °C–50 °C). Voltage hysteresis arises mainly from the cathode, with higher C-rates shortening redox plateaus and broadening the transition region. Elevated temperature lowers impedance, especially near the Mn-redox and transition regions, but accelerates capacity fade. Post-cycling analyses of electrodes confirm structural stability of LMFP64 and indicate loss of lithium inventory (LLI) as the source of capacity fade. This LLI causes potential slippage between the LMFP64 and LTO electrodes, which decreases the Fe-redox plateau width. Long-term cycling highlights the critical role of electrode overhang: cathode overhang mitigates capacity fade by buffering lithium loss, whereas anode overhang cells experience faster capacity decline due to uncompensated lithium depletion. These results clarify LMFP64/LTO battery impedance evolution, thermal effects, and degradation pathways and provide insights for their applications in electric vehicles.

Area Specific Impedance↗
DOE OSTI2022

Insights into dual-functional modification for water stability enhancement of mesoporous zirconium metal–organic frameworks

The stability of metal–organic frameworks (MOFs) in water affects their ability to function as chemical catalysts, their capacity as adsorbents for separations in water vapor presence, and their usefulness as recyclable water harvesters. Here, we have examined water stability of four node-modified variants of the mesoporous MOF, NU-1000, namely formate-, Acac-, TFacac-, and Facac-NU-1000, comparing these with node-accessible NU-1000. These NU-1000 variants present ligands grafted to NU-1000's hexa-Zr(IV)-oxy nodes by displacing terminal aqua and hydroxo ligands. Facac-NU-1000, containing the most hydrophobic ligands, showed the greatest water stability, being able to undergo at least 20 water adsorption/desorption cycles without loss of water uptake capacity. Computational studies revealed dual salutary functions of installed Facac ligands: (1) enhancement of framework mechanical stability due to electrostatic interactions; and (2) transformation and shielding of the otherwise highly hydrophilic nodes from H-bonding interactions with free water, presumably leading to weaker channel-stressing capillary forces during water evacuation – consistent with trends in free energies of dehydration across the NU-1000 variants. Water harvesting and hydrolysis of chemical warfare agent simulants were examined to gauge the functional consequences of modification and mechanical stabilization of NU-1000 by Facac ligands. The studies revealed a harvesting capacity of ~1.1 L of water vapor per gram of Facac-NU-1000 per sorption cycle. They also revealed retention of catalytic MOF activity following 20 water uptake and release cycles. This study provides insights into the basis for node-ligand-engendered stabilization of wide-channel MOFs against collapse during water removal.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Testing unified theories for ozone response in C 4 species

Abstract There is tremendous interspecific variability in O 3 sensitivity among C 3 species, but variation among C 4 species has been less clearly documented. It is also unclear whether stomatal conductance and leaf structure such as leaf mass per area (LMA) determine the variation in sensitivity to O 3 across species. In this study, we investigated leaf morphological, chemical, and photosynthetic responses of 22 genotypes of four C 4 bioenergy species (switchgrass, sorghum, maize, and miscanthus) to elevated O 3 in side‐by‐side field experiments using free‐air O 3 concentration enrichment (FACE). The C 4 species varied largely in leaf morphology, physiology, and nutrient composition. Elevated O 3 did not alter leaf morphology, nutrient content, stomatal conductance, chlorophyll fluorescence, and respiration in most genotypes but reduced net CO 2 assimilation in maize and photosynthetic capacity in sorghum and maize. Species with lower LMA and higher stomatal conductance tended to show greater losses in photosynthetic rate and capacity in elevated O 3 compared with species with higher LMA and lower stomatal conductance. Stomatal conductance was the strongest determinant of leaf photosynthetic rate and capacity. The response of both area‐ and mass‐based leaf photosynthetic rate and capacity to elevated O 3 were not affected by LMA directly but negatively influenced by LMA indirectly through stomatal conductance. These results demonstrate that there is significant variation in O 3 sensitivity among C 4 species with maize and sorghum showing greater sensitivity of photosynthesis to O 3 than switchgrass and miscanthus. Interspecific variation in O 3 sensitivity was determined by direct effects of stomatal conductance and indirect effects of LMA. This is the first study to provide a test of unifying theories explaining variation in O 3 sensitivity in C 4 bioenergy grasses. These findings advance understanding of O 3 tolerance in C 4 grasses and could aid in optimal placement of diverse C 4 bioenergy feedstock across a polluted landscape.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Definition of Redox Centers in Reactions of Lithium Intercalation in Li 3 RuO 4 Polymorphs

Cathodes based on layered LiMO 2 are the limiting components in the path toward Li-ion batteries with energy densities suitable for electric vehicles. Introducing an over-stoichiometry of Li increases storage capacity beyond a conventional mechanism of formal transition metal redox. However, the role and fate of the oxide ligands in such intriguing additional capacity remain unclear. This reactivity was predicted in Li 3 RuO 4 , making it a valuable model system. For this study, a comprehensive analysis of the redox activity of both Ru and O under different electrochemical conditions was carried out, and the effect of Li/Ru ordering was evaluated. Li 3 RuO 4 displays highly reversible Li intercalation to Li 4 RuO 4 below 2.5 V vs Li + /Li 0 , with conventional reactivity through the formal Ru 5+ -Ru 4+ couple. In turn, it can also undergo anodic Li extraction at 3.9 V, which involves O states to a much greater extent than Ru. This reaction competes with side processes such as electrolyte decomposition and, to a much lesser extent, oxygen loss. Although the associated capacity is reversible, reintercalation unlocks a different, conventional pathway also involving the formal Ru 5+ -Ru 4+ couple despite operating above 2.5 V, leading to chemical hysteresis. This new pathway is both chemically and electrochemically reversible in subsequent cycles. This work exemplifies both the challenge of stabilizing highly depleted O states, even with 4d metals, and the ability of solids to access the same redox couple at two very different potential windows depending on the underlying structural changes. It highlights the importance of properly defining the covalency of oxides when defining charge compensation in view of the design of materials with high capacity for Li storage.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Microwave-assisted synthesis of mixed-linker covalent organic frameworks enabling tunable and ultrahigh iodine capture

The use of covalent organic frameworks (COFs) for hazardous radioiodine capture has been highly sought after recently. However, the synthesis of high-performance COF adsorbents while circumventing the limitations of traditional solvothermal methods remains largely unexplored. Herein, we for the first time combine microwave-assisted synthesis and mixed-linker strategy to fabricate multivariate COF adsorbents (X% OMe-TFB-BD COFs, X% = 0, 33, 50, 67, and 100 mol%) with varying ratios of benzidine (BD) and 3,3'-dimethoxylbenzidine (BD-OMe) linkers in a rapid and facile manner. Adjusting the BD-OMe/BD mole ratios has led to distinct variations in density, crystallinity, porosity, morphology, and thermal/chemical stability of the resultant COFs, which empowered fine-tuning of the adsorption performance towards static iodine vapor. Remarkably, the 50% OMe-TFB-BD COF exhibited an ultrahigh iodine adsorption capability of 8.2 g g –1 , surpassing those of single-component COFs, mixed-linker COFs with other methoxy content, physically blended mixtures, and most existing COF adsorbents. Moreover, 50% OMe-TFB-BD COF was recyclable seven times without obvious loss in its adsorption capacity. Finally, this work underscores the substantial potential of microwave-assisted mixed-linker strategy as a viable approach for developing multivariate COFs with shortened reaction times, precisely tailored pore environment, and tunable sorption properties, which are of considerable promise for environmental remediation and other niche applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Boric acid removal with polyol-functionalized polyether membranes

Poor selectivity of conventional desalination membranes for boron often necessitates multi-stage treatment trains to achieve desired boron removal for end uses such as irrigation. One approach to membrane design for improved single-pass boric acid removal is via incorporation of chelating ligands that selectively sorb boron. In this study, membranes based on epoxy-amine cross-linked poly(glycidyl glycidyl ether) (PGGE) were synthesized and functionalized with N-methyl-d-glucamine (NMDG), a polyol known to interact selectively with boron. PGGE and PGGE-NMDG membranes exhibited boron sorption isotherms that were well-described by dual mode isotherms. PGGE-NMDG sorbed 2.5 mmol B/g dry polymer from a neutral aqueous solution containing 100 mmol B/L, which was almost three times the adsorption density of a commercial boron selective resin, Amberlite IRA743. Further, the membranes were regenerated in acid without a significant loss of boron sorption capacity over four cycles. Interactions between boron and NMDG and PGGE sites (e.g., epoxides) impacted boron diffusion in both membranes. The use of ligand functionalized membranes to capture target solutes such as boron requires high loading of interacting sites to maximize uptake capacity. Establishing fundamental structure/property rules for boron selectivity could lead to new material designs with improved boron separation properties for water purification.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Photo-oxidation of semicrystalline polymers: Effect of stress triaxiality on ductility

The effect of stress triaxiality on the strain-to-fracture of as-received and photo-oxidized polyamide-6 (PA-6) was investigated using mechanical testing, synchrotron X-ray tomography, and finite element analyses. Mechanical tests were conducted on cylindrical and round notched specimens, where different notch radii were used to vary the stress triaxiality. The specimens were aged by exposure to ultra-violet (UV) radiation at 60∘, causing photo-oxidation. As-received and so-aged specimens were loaded to failure (complete loss of load carrying capacity). For both unaged and aged specimens, a higher triaxiality led to a lower strain-to-fracture. To elucidate the micromechanical damage that mediates fracture in both conditions, specimens with an intermediate notch sharpness were loaded to the peak load, unloaded, and scanned ex situ using synchrotron X-ray tomography. Damage in the unaged bar was found to occur by cavitation and was concentrated at the center of the specimen, where the triaxiality is highest. In the UV-aged bar, a network of inter-connected chemical cracks were found on the notch surface, where the triaxiality is lowest. Finite element analyses were deployed to approximate the local triaxiality at damaged regions in the unaged and UV-aged specimens using a constitutive relation for semicrystalline polymers. From these analyses, the relationship between local triaxiality and strain-to-fracture was quantified for both unaged and photo-oxidized PA-6. Both unaged and photo-oxidized PA-6 showed similar decreases in ductility with triaxiality, hinting at common ductile fracture processes.

36 MATERIALS SCIENCE↗