Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “band modulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

Advanced tracking and data relay experiment study: Multimode transponder experiment

A series of experiments utilizing a multimode transponder mounted in an aircraft working either through a spacecraft or directly with a ground station is studied. The purpose of the experiments is to determine the best modulation and encoding techniques for combating RFI and multipath propagation and to determine the characteristics of VHF and UHF RFI in discreet bands. The experiments would also determine the feasibility and accuracy of range and range rate measurements with the various modulation and encoding techniques.

Cnossen, R. S.↗
NASA NTRS1973

Advanced tracking and data relay experiments study: Multimode transponder experiment analysis procedure

Plans and implementation concepts were developed for utilizing a multimode transponder mounted in an aircraft working either through a spacecraft or directly with a ground station. The purpose would be to determine the best modulation and encoding techniques for combating RFI and multipath propagation and to determine the characteristics of VHF and UHF RFI in discreet bands. The experiments would also determine the feasibility and accuracy of range and range rate measurements with the various modulation and encoding techniques.

Cnossen, R. S.↗
NASA NTRS2003

Infrared Avionics Signal Distribution using Wavelength Division Multiplexing

Pilots in the cockpits of aircrafts currently communicate with ground stations using Radio Frequency (RF) signals. Antennas mounted outside the aircraft receive and transmit RF signals from and to the ground stations. The RF signals received at the antennas are sent to the cockpit using coaxial cables. As the number of antennas needed to provide more than one frequency band in aircrafts increases, RF distribution media (such as coaxial cable) adds to the complexity and weight of the cockpit wiring. Concomitantly, the safety and signal to noise ratio also decreases due to the use of RF signals. The University of Oklahoma is collaborating with the National Aeronautics and Space Administration to develop optical fiber based schemes to replace the coaxial cable used for RF signal distribution within an aircraft. The project aims at exploiting emerging Wavelength Division Multiplexing (WDM) techniques to reduce the weight of cabling, and increase the signal to noise ratio and reliability. This will be achieved by wavelength division multiplexing the signals from the various antennas and then demultiplexing the signals to recover the original signals at the cockpit. This paper will show that (i) RF signals can not only be wavelength multiplexed at the end of a fiber, but additional signals can be inserted into the middle of the fiber using WDM technology, and (ii) the signals can also be successfully extracted by tapping into the middle of the fiber. We are currently extending our previous laboratory prototype (which could multiplex signals only at the end of the fiber) to include additional multiplexing and demultiplexing of RF signals from the middle of the optical backbone with a view to validating the proof of concept, and carrying out measurements to determine the effectiveness of Wavelength Division Multiplexing for avionics applications. A test bed to perform measurements of several relevant parameters for various modulation schemes and frequencies (such as VHF, UHF, and L-Band) has been implemented. In particular, results of transmitter and receiver noise, bit-error-rate (BER), effect of cross talk on the quality of the multiplexed signals, and Signal to Noise ratio and Carrier to Noise ratio, obtained using the aforementioned test bed, will be presented.

Atiquzzaman, Mohammed↗
NASA NTRS2016

Development and Characterization of a Small Spacecraft Electro-Optic Scanner for Free-Space Laser Communications

Emergent data-intensive missions coupled with dramatic reductions in spacecraft size plus an increasing number of space-based missions necessitates new high performance, compact and low cost communications technology. Free space optical communications offer advantages including orders of magnitude increase for data rate performance, increased security, immunity to jamming and lack of frequency allocation requirements when compared with conventional radio frequency (RF) means. The spatial coherence and low divergence associated with the optical frequencies of laser communications lends themselves to superior performance, but this increased directionality also creates one of the primary technical challenges in establishing a laser communications link by repeatedly and reliably pointing the beam onto the receive aperture. Several solutions have emerged from wide angle (slow) mechanical articulation systems, fine (fast) steering mirrors and rotating prisms, inertial compensation gyros and vibration isolation cancellation systems, but each requires moving components and imparts a measured amount of burden on the host platform. The complexity, cost and size of current mechanically scanned solutions limits their platform applicability, and restricts the feasibility of deploying optical communications payloads on very compact spacecraft employing critical systems. A high speed, wide angle, non-mechanical solution is therefore desirable. The purpose of this work is to share the development, testing, and demonstration of a breadboard prototype electro-optic (EO) scanned laser-communication link (see Figure 1). This demonstration is a step toward realizing ultra-low Size, Weight and Power (SWaP) SmallSat/MicroSat EO non-mechanical laser beam steering modules for high bandwidth ( greater than Gbps) free-space data links operating in the 1550 nm wavelength bands. The elimination of all moving parts will dramatically reduce SWaP and cost, increase component lifetime and reliability, and simplify the system design of laser communication modules. This paper describes the target mission architectures and requirements (few cubic centimeters of volume, 10's of grams of weight with milliwatts of power) and design of the beam steering module. Laboratory metrology is used to determine the component performance including horizontal and vertical resolution (20urad) as a function of control voltage (see Figure 2), transition time (0.1-1ms), pointing repeatability and optic insertion loss. A test bed system demonstration, including a full laser communications link, is conducted. The capabilities of this new EO beam steerer provide an opportunity to dramatically improve space communications through increased utilization of laser technology on smaller platforms than were previously attainable.

Laser Optical Communications↗
NASA NTRS1980

Shuttle orbiter Ku-band radar/communications system design evaluation. Deliverable test equipment evaluation

The Ku-band test equipment, known as the Deliverable System Test equipment (DSTE), is reviewed and evaluated. The DSTE is semiautomated and computer programs were generated for 14 communication mode tests and 17 radar mode tests. The 31 test modules provide a good cross section of tests with which to exercise the Ku-band system; however, it is very limited when being used to verify Ku-band system performance. More detailed test descriptions are needed, and a major area of concern is the DSTE sell-off procedure which is inadequate.

Maronde, R. G.↗
NASA NTRS2007

High-Capacity Communications from Martian Distances

High capacity communications from Martian distances, required for the envisioned human exploration and desirable for data-intensive science missions, is challenging. NASA s Deep Space Network currently requires large antennas to close RF telemetry links operating at kilobit-per-second data rates. To accommodate higher rate communications, NASA is considering means to achieve greater effective aperture at its ground stations. This report, focusing on the return link from Mars to Earth, demonstrates that without excessive research and development expenditure, operational Mars-to-Earth RF communications systems can achieve data rates up to 1 Gbps by 2020 using technology that today is at technology readiness level (TRL) 4-5. Advanced technology to achieve the needed increase in spacecraft power and transmit aperture is feasible at an only moderate increase in spacecraft mass and technology risk. In addition, both power-efficient, near-capacity coding and modulation and greater aperture from the DSN array will be required. In accord with these results and conclusions, investment in the following technologies is recommended:(1) lightweight (1 kg/sq m density) spacecraft antenna systems; (2) a Ka-band receive ground array consisting of relatively small (10-15 m) antennas; (3) coding and modulation technology that reduces spacecraft power by at least 3 dB; and (4) efficient generation of kilowatt-level spacecraft RF power.

Williams, W. Dan↗
NASA NTRS2013

Sleuthing the MSL EDL Performance from an X Band Carrier Perspective

During the Entry, Descent, and Landing (EDL) of NASA's Mars Science Laboratory (MSL), or Curiosity, rover to Gale Crater on Mars on August 6, 2012 UTC, the rover transmitted an X-band signal composed of carrier and tone frequencies and a UHF signal modulated with an 8kbps data stream. During EDL, the spacecraft's orientation is determined by its guidance and mechanical subsystems to ensure that the vehicle land safely at its destination. Although orientation to maximize telecom performance is not possible, antennas are especially designed and mounted to provide the best possible line of sight to Earth and to the Mars orbiters supporting MSL's landing. The tones and data transmitted over these links are selected carefully to reflect the most essential parameters of the vehicle's state and the performance of the EDL subsystems for post-EDL reconstruction should no further data transmission from the vehicle be possible. This paper addresses the configuration of the X band receive system used at NASA / JPL's Deep Space Network (DSN) to capture the signal spectrum of MSL's X band carrier and tone signal, examines the MSL vehicle state information obtained from the X band carrier signal only and contrasts the Doppler-derived information against the post-EDL known vehicle state. The paper begins with a description of the MSL EDL sequence of events and discusses the impact of the EDL maneuvers such as guided entry, parachute deploy, and powered descent on the frequency observables expected at the DSN. The range of Doppler dynamics possible is derived from extensive 6 Degrees-Of-Freedom (6 DOF) vehicle state calculations performed by MSL's EDL simulation team. The configuration of the DSN's receive system, using the Radio Science Receivers (RSR) to perform open-loop recording for both for nominal and off-nominal EDL scenarios, is detailed. Expected signal carrier power-to-noise levels during EDL are shown and their impact on signal detection is considered. Particular attention is given to the selection of the appropriate RSR processing bandwidths and to its configuration for real-time signal detection. The X-band carrier frequency obtained through post-processing of the open-loop recorded spectrum is given. Detection of spacecraft status and completion of key vehicle events through their Doppler signature is discussed and illustrated. This Doppler-derived information is compared against the very accurate vehicle data obtained post-EDL via MSL's UHF radio subsystem. The paper concludes with a discussion on the advantages and disadvantages of transmitting the X-band carrier and tone signal in the general context of EDL communications and lessons learned for future missions with EDL sequences are given

Mars Science Laboratory (MSL)↗
NASA NTRS2003

Packaging Considerations for Integrated RF Microphotonic Receiver at Ka-Band

The NASA Computing, Information and Communications Technology (CICT) Program is supporting the development of an RF microphotonic Ka-band receiver. The receiver consists of a lithium niobate micro-disk that enables the incoming RF signal (up to Ka-band) to be coupled to the optical signal (approx. 200 THz). The modulated optical signal is detected by the high-speed photonic signal processing electronics. When compared with an all-electronic approach, the microphotonic receiver technology offers 1 Ox smaller volume, smaller weight, and smaller power consumption, greater sensitivity, and optical isolation for applications in extreme environments. It could potentially be implemented to support planetary surface-to-surface and surface-to-relay communications, as well as high-data-rate inter-satellite links. We are currently studying a number of fabrication and integration issues that could result as this technology is advanced for potential insertion into a NASA mission. The results of our preliminary effort to integrate the RF microphotonic receiver components (e.g., the lithium niobate micro-disk, the optical elements, and the Ka-band patch antenna) on an etched silicon wafer will be presented, In addition, the concomitant integration and packaging issues, and the potential NASA applications will be discussed.

Nguyen, Hung↗
NASA NTRS1978

Subcarrier phase recovery performance in bent-pipe mode of Shuttle data transmission

The subcarrier phase recovery is analyzed for the bent-pipe mode of Space Shuttle detached-payload data transmission on the Tracking and Data Relay Satellite System (TDRSS) Ku-band return link. The high-power component of the subcarrier modulation is unrestored payload data, either at baseband or modulating another subcarrier. At the receiver a Costas loop recovers the subcarrier phase. To analyze its performance in the baseband case, we obtain the loop S-curve, the power spectral density of the equivalent noise process, and the loop phase error variance.

Mckenzie, T. M.↗
NASA NTRS1983

Microwave monolithic integrated circuit development for future spaceborne phased array antennas

The development of fully monolithic gallium arsenide (GaAs) receive and transmit modules suitable for phased array antenna applications in the 30/20 gigahertz bands is presented. Specifications and various design approaches to achieve the design goals are described. Initial design and performance of submodules and associated active and passive components are presented. A tradeoff study summary is presented highlighting the advantages of distributed amplifier approach compared to the conventional single power source designs.

Anzic, G.↗
NASA NTRS1984

Microwave monolithic integrated circuit development for future spaceborne phased array antennas

The development of fully monolithic gallium arsenide (GaAs) receive and transmit modules suitable for phased array antenna applications in the 30/20 gigahertz bands is presented. Specifications and various design approaches to achieve the design goals are described. Initial design and performance of submodules and associated active and passive components are presented. A tradeoff study summary is presented, highlighting the advantages of a distributed amplifier approach compared to the conventional single power source designs. Previously announced in STAR as N84-13399

Anzic, G.↗
NASA NTRS1988

Striated spectral activity in Jovian and Saturnian radio emission

Examination of high time resolution frequency-time spectrograms of radio emission measured near the Voyager 1 and 2 encounters with Jupiter reveals occasional striation patterns within the normally diffuse hectometric radiation. The patterns are characterized by distinctive banded structures of enhanced intensity meandering in frequency over time scales of minutes to tens of minutes. This banded form of striated spectral activity (SSA) has an occurrence probability of the order of 5 percent during the three weeks before and after Jupiter encounters. Plots of single 6-s frequency sweeps often exhibit a slow rise in intensity followed by a sharp drop-off in each band as frequency decreases. Banded SSA is often preceded or followed by chaotic SSA in which banding of the emission becomes discontinuous or unrecognizable, although the intensity modulation is still evident. Although SSA normally occurs in the frequency range of roughly 0.2-1.0 MHz, similar but longer-lasting patterns have been found occasionally in decametric emission above 10 MHz. Analogous modulation has also been observed in the Saturnian radio emission, suggesting that SSA may be a common feature intrinsic to the radio emission at both planets.

Thieman, James R.↗
NASA NTRS1994

Constant-Delay Broadband Microwave Phase Modulator

Varactor diodes and transformer waveguide sections used instead of tuned circuits. Microwave phase modulator exhibits approximately flat delay-vs.-frequency response in frequency band of interest, according to design computations.

Francisco, Mark↗
NASA NTRS1988

Ku-band high efficiency GaAs MMIC power amplifiers

The development of Ku-band high efficiency GaAs MMIC power amplifiers is examined. Three amplifier modules operating over the 13 to 15 GHz frequency range are to be developed. The first MMIC is a 1 W variable power amplifier (VPA) with 35 percent efficiency. On-chip digital gain control is to be provided. The second MMIC is a medium power amplifier (MPA) with an output power goal of 1 W and 40 percent power-added efficiency. The third MMIC is a high power amplifier (HPA) with 4 W output power goal and 40 percent power-added efficiency. An output power of 0.36 W/mm with 49 percent efficiency was obtained on an ion implanted single gate MESFET at 15 GHz. On a dual gate MESFET, an output power of 0.42 W/mm with 27 percent efficiency was obtained. A mask set was designed that includes single stage, two stage, and three stage single gate amplifiers. A single stage 600 micron amplifier produced 0.4 W/mm output power with 40 percent efficiency at 14 GHz. A four stage dual gate amplifier generated 500 mW of output power with 20 dB gain at 17 GHz. A four-bit digital-to-analog converter was designed and fabricated which has an output swing of -3 V to +/- 1 V.

Tserng, H. Q.↗
NASA NTRS2022

Infrared Spectral Responses of the Ocean Color Instrument (OCI) Pre-assembly and Integration

Spectral characterizations were made of the Ocean Color Instrument (OCI) short-wave infrared (SWIR) Detection Subassembly (SDS) responses (940–2260 nm) prior to their integration. Using modulated output light from a Fourier transform spectrometer, the in-band relative spectral responses of the nine different configurations of SDSs were found along with out-of-band (OOB) sensitivity. From these spectral responses, the center wavelengths (λ0), full widths at half of the maximum, full widths at 1% of the maximum, and OOB rejection ratios were determined. All spectral parameters are within requirements. There are 2–8 repeats of each configuration, and the 1 σ spread among repeats is largest for the 1250 nm and 1615 nm high-gain configurations and is greater than 1 nm. The engineering requirement is for these values to be within ±4 nm and ±10 nm, respectively, of 19 the nominal λ0. There is also a λ0 temperature dependence, which is expected. This temperature dependence is nearly a linear function of wavelength with a 9.5 × 10−3 nm K−1 relationship on average.

PACE↗
NASA NTRS1990

Digital Demodulator For Advanced Receiver

Complexity and cost reduced by new design for half-band filters. Digital demodulator designed for use in reception of phase- and amplitude-modulated digital signals of bandwidths up to 15 MHz on microwave carriers. System performs coherent demodulation in phase and in quadrature with carrier locked in phase to intermediate frequency of 10 MHz. Design suitable for fabrication in very-large-scale integrated circuitry. Principal innovative feature of demodulator is design of half-band digital low-pass filters that remove sum-frequency components.

Sadr, Ramin↗
NASA NTRS2004

Use of the 37-38 GHz and 40-40.5 GHz Ka-bands for Deep Space Communications

This paper covers a wide variety of issues associated with the implementation and use of these frequency bands for deep space communications. Performance issues, such as ground station pointing stability, ground antenna gain, antenna pattern, and propagation effects such as due to atmospheric, charged-particle and space loss at 37 GHz, will be addressed in comparison to the 32 GHz Ka-band deep space allocation. Issues with the use of and competition for this spectrum also will be covered. The state of the hardware developed (or proposed) for operating in this frequency band will be covered from the standpoint of the prospects for achieving higher data rates that could be accommodated in the available bandwidth. Hardware areas to be explored include modulators, digital-to-analog converters, filters, power amplifiers, receivers, and antennas. The potential users of the frequency band will be explored as well as their anticipated methods to achieve the potential high data rates and the implications of the competition for bandwidth.

telecommunications↗