Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “attribute measurement”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

Investigation of Distribution of Losses in a Conservatively Designed Turbine

A primary objective of turbine research is to obtain information that will aid in the design of gas turbines for any given application with minimum losses. As part of a program to obtain such information, flow surveys downstream of both the stator and the rotor of an experimental turbine were made in order to obtain detailed information about the flow conditions and the losses within the machine. The single-stage, low-radius-ratio turbine studied is relatively conservative in design, having low rotor-inlet relative Mach number, low turning angle, and high reaction at the rotor-root section. Surveys of the flow conditions and of the losses within the turbine are presented. The measured over-all losses are analyzed in order to approximate the magnitudes of the various components of loss. It was found that the major losses in the turbine were in the rotor near the blade extremities. The losses in the tip region were considerably greater than those near the hub. The existence of secondary flows at the exit of both the stator and the rotor was indicated by the presence of low-velocity cores near both the hub and the tip sections. Analysis of the losses by an empirical method indicated that the rotor-profile and tip-clearance losses are 31 and 9 percent of the adjusted measured total rotor loss, respectively. The remaining 60 percent loss was attributed to secondary flows.

TURBINES - AXIAL-FLOW↗
NASA NTRS1977

Experimental studies of flow separation of the GA(W)-2 airfoil at low speeds

Wind tunnel tests have been conducted on a NASA GA(W)-2 airfoil section at Reynolds number of 2.2 x 10(exp 6) and Mach number of 0.13. Detailed measurements of flow fields associated with turbulent boundary layers have been obtained at angles of attack of 10.3, 14.4, and 18.3 deg. Pre- and post-separated velocity and pressure survey results over the airfoil and in the associated wake are presented. Extensive force, pressure, tuft survey, hot-film survey, local skin friction, and boundary layer data are also included. Pressure distributions and separation point locations show good agreement with theory for the two lower angles of attack. Boundary layer displacement thickness, momentum thickness, and shape factor agree well with theory up to the point of separation. There is considerable disparity between extent of flow reversal in the wake as measured by pressure and hot-film probes. The difference is attributed to the intermittent nature of the flow reversal.

Seetharam, H. C.↗
NASA NTRS1997

Experimental Studies of Flow Separation of the NACA 2412 Airfoil at Low Speeds

Wind tunnel tests have been conducted on an NACA 2412 airfoil section at Reynolds number of 2.2 x 10(exp 6) and Mach number of 0.13. Detailed measurements of flow fields associated with turbulent boundary layers have been obtained at angles of attack of 12.4 degrees, 14.4 degrees, and 16.4 degrees. Pre- and post-separated velocity and pressure survey results over the airfoil and in the associated wake are presented. Extensive force, pressure, tuft survey, hot-film survey, local skin friction, and boundary layer data are also included. Pressure distributions and separation point locations show good agreement with theory for the two layer angles of attack. Boundary layer displacement thickness, momentum thickness, and shape factor agree well with theory up to the point of separation. There is considerable disparity between extent of flow reversal in the wake as measured by pressure and hot-film probes. The difference is attributed to the intermittent nature of the flow reversal.

Seetharam, H. C.↗
NASA NTRS1994

On the problem of measuring interannual wind speed variations using SSMI data

The first Special Sensor Microwave Imager (SSMI) was launched on the Defense Meteorological Satellite Program (DMSP) F8 spacecraft in July 1987, and wind speed was no longer retrieved after December 1991. A second SSMI was launched on DMSP F10 in December 1990. Interpretation of the 1987-1993 (or longer) SSMI wind speed time series is dependent upon the space and time characteristics of the differences between F8 and F10 SSMI measurements. The 10 deg-zonal averaged monthly mean F8-F10 wind speed difference was negative (positive) for wind speeds less (greater) than 7.9 m/s, reaching -0.43 (0.32) m/s at 5(10) m/s. Between 60 deg S and 60 deg N the 10 deg-zonal averaged monthly mean F8-F10 wind speed bias was greater than +/- 0.5 m/s on several occasions. From 60 deg S - 60 deg N the 1991 average value of the monthly mean root-mean-square difference between daily F8 and F10 wind speeds in 10 deg-longitudinal bands was 2.0 m/s.In the 60 deg S - 60 deg N region, about 50% of the daily F8 and F10 wind speed differences was caused by measurement non-simultaneity and about 50% of the difference was attributed to other factors, such as instrument noise and the different azimuthal orientations of each SSMI.

Halpern, David↗
NASA NTRS1994

A critical evaluation of semianalytic methods in the study of centrally heated, unresolved, infrared sources

We critically evaluate current methods of analysis in infrared (IR) astronomy and investigate the conditions under which these semianalytic methods are reliable. Specifically we examine the usual assumptions of homogeneities in dust density and temperature, and neglect of opacity effects when applied to internally heated, unresolved IR sources. To accomplish this, a series of radiation transport models for these sources have been constructed. The model results are treated as observed quantities and analyzed to derive the source parameters, using simple semianalytic methods. The discrepancies between the derived and actual model parameters can then be attributed to the limitations of the analysis methods and provide a measure of their reliability. Applying this approach to centrally heated, unresolved IR sources, we have studied in detail the following diagnostic problems: (1) determination of dust mass from monochromatic and integrated luminosities; (2) estimation of dust temperature distribution from color temperatures derived from the flux spectrum; and (3) determination of the empirical grain emissivity law (opacity function) for both continuum and spectral features.

Doty, Steven D.↗
NASA NTRS2000

Mars Aerobot Missions

Mars aerobots constitute a class of mission nearly a factor of 10 smaller than earlier concepts for Mars balloons. A key goal is to achieve high payload mass fraction in a small total systems mass and to maximize the scientific potential of that payload. The "low and slow" attributes of aerobot flight paths afford advantages for many observations and measurements of Mars. Scientific objectives include surveys of remnant magnetism, studies of the surface with high resolution stereo imaging, and investigations of the structure and dynamics of the atmosphere with an in situ meteorology payload.

Greeley, R.↗
NASA NTRS2021

The Effect of Missing Groups in the Calculation of the Solar Irradiance Deficit: Analysis of the Sunspot Areas from the SOON Network

Sunspot areas are one of the most important indices of solar activity. To obtain an extended time series covering multiple solar cycles one must combine data from different observatories after a proper comparison and calibration of the individual data sets. We compare the daily and group values of sunspot areas provided by the different stations from the Solar Optical Observing Network, SOON, which are determined using similar instruments and techniques. We investigate if there are systematic differences among the stations and whether the differences in the daily values can be attributed to missing groups in the records or errors in the measurements. We find significant differences among the stations of the SOON network in terms of sizes (average daily and group values), quality of observations and coverage (considering number of missing groups and data gaps). Our results indicate that calibration factors for daily values can be used with confidence to combine data sets from different stations. However, for some applications which require the location of the sunspot groups the same correction factors should not be used. We estimate the irradiance deficit due to sunspot through the Photometric Sunspot Index and compare the output from similar data sets to quantify the effect of missing groups. We find differences as high as 150 ppm during the maximum of solar cycle. The effect increases for sunspot groups near the center of the disk accounting for about 80% of the observed differences.

Luis Leuzzi↗
NASA NTRS2015

MARS - Multi-component Adsorption Recirculation System

Goals - Measure carbon dioxide adsorption isotherms on 13X zeolite - Measured using a volumetric method - Injected CO2 is adsorbed and measured using the pressure loss and the ideal gas law to attribute the pressure loss to moles of adsorbed CO2.

Jack Cunningham↗
NASA NTRS1972

Hypersonic rarefied flow over sharp slender cones

Drag, heat transfer, and number flux were measured on sharp cones in the near free, molecule flow regime, and the results were compared with available Monte Carlo calculations. In general, the calculations predicted the magnitude of the data; however, the heat transfer and drag increased with increasing Knudsen number at a faster rate than predicted. Also the drag coefficients measured for the slender cones at high Knudsen number were higher than predicted for free molecule flow. These disagreements between theory and experiment could possibly be attributed to the simplicity of the surface interaction laws assumed in the theory. Reynolds analogy factors obtained from the experimental measurements agreed with free-molecule values and also with that obtained by the Monte Carlo technique.

Kussoy, M. I.↗
NASA NTRS1989

Coherent radar measurement of ocean currents from geostationary orbit

A coherent HF radar system developed by Barrick has successfully measured ocean surface currents near shore. This innovative system, called CODAR, can map the current vector for coastal areas as large as 10,000 sq km. CODAR's range is limited owing to the strong attenuation suffered by HF ground waves. An alternate technique was proposed by Schuler, in which the cross-product power spectrum of two (different frequency) microwave signals is processed. The frequency of the resonant peak corresponds close by to the Doppler shift of an ocean gravity wave traveling toward the radar at the phase velocity, v(sub p). The slight difference between the frequency of the measured resonant delta K peak and the Doppler frequency shift caused by the motion of the gravity wave is attributed to be the current velocity in the pointing direction of the radar. The Microwave Remote Sensing Laboratory (MIRSL) has considered the feasibility of using this technique to measure ocean surface currents from geostationary satellite platforms. Problems are discussed that must be overcome if a satellite current measurement system is to be realized. MIRSL research activities that address some of these problem areas are discussed. Current measurements are presented that were made using a specially-designed C-Band, step-frequency delta K radar. These measurements suggest that progress is being achieved in detecting ocean surface current motion for a wide variety of ocean surface conditions.

Mcintosh, R. E.↗
NASA NTRS1983

Accelerated degradation of silicon metallization systems

Clemson University has been engaged for the past five years in a program to determine the reliability attributes of solar cells by means of accelerated test procedures. The cells are electrically measured and visually inspected and then subjected for a period of time to stress in excess of that normally encountered in use, and then they are reinspected. Changes are noted and the process repeated. This testing has thus far involved 23 different unencapsulated cell types from 12 different manufacturers, and 10 different encapsulated cell types from 9 different manufacturers. Reliability attributes of metallization systems can be classified as major or minor, depending on the severity of the effects observed. As a result of the accelerated testing conducted under the Clemson program, major effects have been observed related to contact resistance and to mechanical adherence and solderability. This paper does not attempt a generalized survey of accelerated test results, but rather concentrates on one particular attribute of metallization that has been observed to cause electrical degradation - increased contact resistance due to Schottky barrier formation. In this example basic semiconductor theory was able to provide an understanding of the electrical effects observed during accelerated stress testing.

Lathrop, J. W.↗
NASA NTRS1996

Decay rate of the second radiation belt

Variations in the Earth's trapped (Van Allen) belts produced by solar flare particle events are not well understood. Few observations of increases in particle populations have been reported. This is particularly true for effects in low Earth orbit, where manned spaceflights are conducted. This paper reports the existence of a second proton belt and it's subsequent decay as measured by a tissue-equivalent proportional counter and a particle spectrometer on five Space Shuttle flights covering an eighteen-month period. The creation of this second belt is attributed to the injection of particles from a solar particle event which occurred at 2246 UT, March 22, 1991. Comparisons with observations onboard the Russian Mir space station and other unmanned satellites are made. Shuttle measurements and data from other spacecraft are used to determine that the e-folding time of the peak of the second proton belt. It was ten months. Proton populations in the second belt returned to values of quiescent times within eighteen months. The increase in absorbed dose attributed to protons in the second belt was approximately 20%. Passive dosimeter measurements were in good agreement with this value.

Badhwar, G. D.↗
NASA NTRS1993

Trapped belt variations and their effects on human space flights

Variations in the Earth's trapped (Van Allen) belts produced by solar flare particle events are not well understood. This paper reports the existence of a second proton belt and its subsequent decay as measured by a tissue-equivalent proportional counter and a particle spectrometer on five Space Shuttle flights covering an 18-month period. The creation of this second belt is attributed to the injection of particles from a solar particle event which occurred at 2246 UT, March 22, 1991. Comparisons with observations onboard the Russian Mir space station and other unmanned satellites are made. Shuttle measurements and data from other spacecraft are used to determine that the e-folding time of the peak of the second proton belt was ten months. Proton populations in the second belt returned to values of quiescent times within 18 months. The increase in absorbed dose attributed to protons in the second belt was approximately 20 percent. Passive dosimeter measurements were in good agreement with this value.

Robbins, Donald E.↗
NASA NTRS2015

Climate Absolute Radiance and Refractivity Observatory (CLARREO)

The Climate Absolute Radiance and Refractivity Observatory (CLARREO) is a mission, led and developed by NASA, that will measure a variety of climate variables with an unprecedented accuracy to quantify and attribute climate change. CLARREO consists of three separate instruments: an infrared (IR) spectrometer, a reflected solar (RS) spectrometer, and a radio occultation (RO) instrument. The mission will contain orbiting radiometers with sufficient accuracy, including on orbit verification, to calibrate other space-based instrumentation, increasing their respective accuracy by as much as an order of magnitude. The IR spectrometer is a Fourier Transform spectrometer (FTS) working in the 5 to 50 microns wavelength region with a goal of 0.1 K (k = 3) accuracy. The FTS will achieve this accuracy using phase change cells to verify thermistor accuracy and heated halos to verify blackbody emissivity, both on orbit. The RS spectrometer will measure the reflectance of the atmosphere in the 0.32 to 2.3 microns wavelength region with an accuracy of 0.3% (k = 2). The status of the instrumentation packages and potential mission options will be presented.

Leckey, John P.↗
NASA NTRS1995

Is chemical heating a major cause of the mesosphere inversion layer?

A region of thermal enhancement of the mesosphere has been detected on numerous occasions by in situ measurements, remote sensing from space, and lidar techniques. The source of these 'temperature inversion layers' has been attributed in the literature to the dissipation relating to dynamical forcing by gravity wave or tidal activity. However, evidence that gravity wave breaking can produce the inversion layer with amplitude as large as that observed in lidar measurements has been limited to results of numerical modeling. An alternative source for the production of the thermal inversion layer in the mesosphere is the direct deposition of heat by exothermic chemical reactions. Two-dimensional modeling combining a comprehensive model of the mesosphere photochemistry with the dynamical transport of long-lived species shows that the region from 80 to 95 km may be heated as much as 3 to 10 K/d during the night and half this rate during the day. Given the uncertainties in our understanding of the dynamics and chemistry for the mesopause region, separating the two sources by passive observations of the mesosphere thermal structure looks to be difficult. Therefore we have considered an active means for producing a mesopause thermal layer, namely the release of ozone into the upper mesosphere from a rocket payload. The induced effects would include artificial enhancements of the OH and Na airglow intensities as well as the mesopause thermal structure. The advantages of the rocket release of ozone is that detection of these effects by ground-based imaging, radar, and lidar systems and comparison of these effects with model predictions would help quantify the partition of the artificial inversion layer production into sources of dynamical and chemical forcing.

Meriwether, John W.↗
NASA NTRS1987

Inferring spectral reflectances of plant elements by simple inversion of bidirectional reflectance measurements

Inverting previously developed explicit expressions for a vertical architecture, bidirectional reflectances measured over corn viewing from the solar quadrant at azimuths near the principal plane are used to determine the spectral reflectances of plant elements. The leaf reflectance values extracted in three visible bands at viewing zenith angles of 70 deg, 60 deg, and 45 deg agree closely with laboratory-measured reflectances of corn leaves. At viewing zenith angle of 30 deg, the inversion breaks down, inasmuch as the inferred plant element reflectances are too high. Satisfactory results are also achieved when the same approach is applied to bidirectional reflectances measured over potted balsam firs, but when applied to soybeans reflectances, the procedure yields unreasonably high leaf reflectances. The failure in this case is attributed to the nonvertical architecture of the soybean canopy; however, for this canopy, inversion based on horizontal architecture is possible. The bidirectional reflectances measured from the solar quadrant, at viewing angles appreciably far from 'hot spot' viewing, approximately equal in magnitude half of the leaf reflectance. The 0.5 ratio is predicted by a previous analysis of opaque horizontal Lambertian facets, as the asymptotic value for a dense canopy at any viewing angle. For soybeans, this ratio applies very closely at 15 deg viewing zenith angle. The results suggest that inversion based on simple architecture, applying explicit expressions, might be of value, either in itself or as a preliminary step before inversion applying complex models.

Otterman, J.↗
NASA NTRS1972

Quartz microbalance studies of an adsorbed helium film.

The resonant frequency of a quartz crystal oscillating in the thickness-shear mode changes by virtue of the mass loading due to any type of film laid down on its surfaces. For a helium film only the normal fraction remains rigidly coupled to the substrate motion. Adsorption isotherms of He-4 measured with this technique show clear departures from conventional nonsuperfluid behavior. We attribute this effect to the onset and presence of superfluidity in the film.

Chester, M.↗
NASA NTRS1972

Measurement of operator workload in an information processing task

This was an experimental study to develop an improved methodology for measuring workload in an information processing task and to assess the effects of shift length and communication density (rate of information flow) on the ability to process and classify verbal messages. Each of twelve subjects was exposed to combinations of three shift lengths and two communication densities in a counterbalanced, repeated measurements experimental design. Results indicated no systematic variation in task performance measures or in other dependent measures as a function of shift length or communication density. This is attributed to the absence of a secondary loading task, an insufficiently taxing work schedule, and the lack of psychological stress. Subjective magnitude estimates of workload showed fatigue (and to a lesser degree, tension) to be a power function of shift length. Estimates of task difficulty and fatigue were initially lower but increased more sharply over time under low density than under high density conditions. An interpretation of findings and recommedations for furture research are included. This research has major implications to human workload problems in information processing of air traffic control verbal data.

Jenney, L. L.↗