Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “YOUNG MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Processing and properties of SiC composites made via binder jet 3D printing and infiltration and pyrolysis of preceramic polymer

The effect of polymer infiltration and pyrolysis (PIP) cycles with polycarbosiloxane on the microstructure, air leak rate, and properties of SiC composites manufactured by a combination of binder jet 3D printing and PIP are reported. The density, Young’s modulus and flexural strength of disk-shaped components increased with the number of PIP cycles. In the case of density, it increased from 2.05 g/cm 3 in one PIP cycle to 2.33 g/cm 3 after three PIP cycles, while values of flexural strength and Young’s modulus at room temperature after three PIP cycles reached 66.8 ± 2.5 MPa and 69.5 ± 2.8 GPa, respectively. Conversely, the air leak rate was found to decrease with number of PIP cycles, and it reached a value of 4 mbar-liter/s after three cycles. The instantaneous coefficient of thermal expansion of the composite was found to change minimally with the number of PIP cycles and had a value of 4 ± 1.2 ppm/°C between 200°C and 1,000°C. Thermal conductivity was found to increase with number of PIP cycles and to decrease with temperature. For example, after 3 PIP cycles it was found to change from 6.72 ± 0.08 to 6.98 ± 0.08 W/mK at 25°C and 7.36 ± 0.08 to 7.96 ± 0.08 W/mK at 300°C. These values were lower than those of crystalline SiC because of the amorphous nature of the matrix and the presence of pores and cracks.

36 MATERIALS SCIENCE↗

Determination of elastic properties of a MnO{sub 2} coating by surface acoustic wave velocity dispersion analysis

MnO{sub 2} is a material of interest in the development of high energy-density batteries, specifically as a coating material for internal 3D structures, thus ensuring rapid energy deployment. Its electrochemical properties have been mapped extensively, but there are, to the best of the authors' knowledge, no records of the elastic properties of thin film MnO{sub 2}. Impulsive stimulated thermal scattering (ISTS), also known as the heterodyne diffraction or transient grating technique, was used to determine the Young's modulus (E) and porosity (ψ) of a 500 nm thick MnO{sub 2} coating on a Si(001) substrate. ISTS is an all optical method that is able to excite and detect surface acoustic waves (SAWs) on opaque samples. From the measured SAW velocity dispersion, the Young's modulus and porosity were determined to be E = 25 ± 1 GPa and ψ=42±1%, respectively. These values were confirmed by independent techniques and determined by a most-squares analysis of the carefully fitted SAW velocity dispersion. This study demonstrates the ability of the presented technique to determine the elastic parameters of a thin, porous film on an anisotropic substrate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

An evaluation of the sandwich beam in four-point bending as a compressive test method for composites

The experimental phase of the study included compressive tests on HTS/PMR-15 graphite/polyimide, 2024-T3 aluminum alloy, and 5052 aluminum honeycomb at room temperature, and tensile tests on graphite/polyimide at room temperature, -157 C, and 316 C. Elastic properties and strength data are presented for three laminates. The room temperature elastic properties were generally found to differ in tension and compression with Young's modulus values differing by as much as twenty-six percent. The effect of temperature on modulus and strength was shown to be laminate dependent. A three-dimensional finite element analysis predicted an essentially uniform, uniaxial compressive stress state in the top flange test section of the sandwich beam. In conclusion, the sandwich beam can be used to obtain accurate, reliable Young's modulus and Poisson's ratio data for advanced composites; however, the ultimate compressive stress for some laminates may be influenced by the specimen geometry.

Shuart, M. J.↗

Invar and Elinvar type amorphous Fe-Cr-B alloys with high corrosion resistance

Amorphous (Fe(1-x)Cr(x))85B15 alloys (x = 0 to 0.15) were prepared from the melts by rapid quenching using a single roller techinque, and their Invar and Elinvar characteristics and corrosion resistance were investigated. With an increase in chromium content the Curie temperature and the saturation magnetic moment per iron atom decreased monotonically, while the crystallization temperature incresed gradually. The thermal expansion coefficient alpha around room temperature became slightly larger with increasing chromium content. Nevertheless, these amorphous alloys exhibited excellent Invar characteristics below the Curie temperature. The value of Young's modulus increased remarkably in a relatively low magnetic field and then saturated at a field of about 80 kA/m, showing a large delta E effect. Its value as well as a longitudinal linear magnetostriction became smaller with an increase in chromium content. The temperature coefficient of Young's modulus changed from postive to negative, and the temperature range showing the Elinvar characteristics became narrower with chromium content. The temperature coefficient of delay time determined from the values of alpha and e was very small. The corrosion resistance of these alloys was extremely improved by chromium addition.

Kikuci, M.↗

Skin-like low-noise elastomeric organic photodiodes

Stretchable optoelectronics made of elastomeric semiconductors could enable the integration of intelligent systems with soft materials, such as those of the biological world. Organic semiconductors and photodiodes have been engineered to be elastomeric; however, for photodetector applications, it remains a challenge to identify an elastomeric bulk heterojunction (e-BHJ) photoactive layer that combines a low Young’s modulus and a high strain at break that yields organic photodiodes with low electronic noise values and high photodetector performance. Here, a blend of an elastomer, a donor-like polymer, and an acceptor-like molecule yields a skin-like e-BHJ with a Young’s modulus of a few megapascals, comparable to values of human tissues, and a high strain at break of 189%. Elastomeric organic photodiodes based on e-BHJ photoactive layers maintain low electronic noise current values in the tens of femtoamperes range and noise equivalent power values in the tens of picowatts range under at least 60% strain.

42 ENGINEERING↗

Understanding the origin of softness in structurally tailored and engineered macromolecular (STEM) gels: A DPD study

Structurally tailored and engineered macromolecular (STEM) gels are polymer networks containing a primary network (the “STEM-0” gel) and side chains that are anchored to this network (forming the “STEM-1” gel). The ability to vary the features of the side chains provides a robust means of tailoring the macroscopic properties of the material. We use dissipative particle dynamics (DPD) simulations to determine the mechanical response of STEM-1 gels to uniaxial compression for various values of the side chain length, n sc . While the Young’s modulus of the material is significantly decreased with increasing n sc (at a fixed density of grafted side chains), above a certain saturation value, increasing n sc does not lead to any further softening of the sample. Using the simulations, we calculate the relevant stresses, which are related to the Young’s modulus and the number of entanglements in the network. We show that the backbone chains become more spread out upon addition of sidechains, leading to a decrease in the physical entanglements between backbone segments. This observation accounts for the decrease of stress in the backbone network and the softening of the networks through the addition of sidechains. For long chains, however, the number density of physical crosslinks between side chains is independent of side chain length; this observation explains the observed stress saturation in the STEM-1 gels. Our approach allows us to correlate the molecular architecture of the gels to the resultant macroscopic mechanical behavior and provide guidelines for fabricating STEM gels with well-defined mechanical properties, which allow the materials to be used for a variety of applications.

36 MATERIALS SCIENCE↗

Tensile properties of 3D-printed wood-filled PLA materials using poplar trees

Fabrication of renewable materials through additive manufacturing using wood-filled polylactic acid (PLA) is an emerging field of study. The variability in the tensile properties of 3D-printed materials due to the variability in woody biomass properties has not been studied. Biomass size reduction, filament extrusion, and 3D-printing methods were investigated to determine the conditions that resulted in consistent printing. Using 20% ball-milled poplar reinforcement in PLA, 210 °C filament extrusion temperature and 230 °C printing temperature were found to be the best conditions. Subsequently, seventy poplar samples from a common garden were used to test the tensile properties of the printed materials. The median tensile strength at yield was 50 MPa, with 5–95 percentiles ranged in 37–54 MPa. Strain% at break had a median value of 2.1%, and 5–95 percentiles were 1.7–2.7%. The median Young's modulus was 3.65 GPa, and 5–95 percentiles ranged in 2.9–4.1 GPa. Biomass density was correlated to composite density. Median particle size of ball-milled poplar was negatively correlated with tensile strength. Composite density affected tensile strength of the composite. β-glycosidic bond of polysaccharides in biomass affected Young's modulus of the composite. Overall, these data show that genotypic variation among Populus trichocarpa have substantial effect on tensile properties of 3D printed PLA-poplar materials.

36 MATERIALS SCIENCE↗

High Temperature Mechanical Characterization and Analysis of Al2O3 /Al2O3 Composition

Sixteen ply unidirectional zirconia coated single crystal Al2O3 fiber reinforced polycrystalline Al2O3 was tested in uniaxial tension at temperatures to 1400 C in air. Fiber volume fractions ranged from 26 to 31%. The matrix has primarily open porosity of approximately 40%. Theories for predicting the Young's modulus, first matrix cracking stress, and ultimate strength were applied and evaluated for suitability in predicting the mechanical behavior of Al2O3/Al2O3 composites. The composite exhibited pseudo tough behavior (increased area under the stress/strain curve relative to monolithic alumina) from 22 to 1400 C. The rule-of-mixtures provides a good estimate of the Young's modulus of the composite using the constituent properties from room temperature to approximately 1200 C for short term static tensile tests in air. The ACK theory provides the best approximation of the first matrix cracking stress while accounting for residual stresses at room temperature. Difficulties in determining the fiber/matrix interfacial shear stress at high temperatures prevented the accurate prediction of the first matrix cracking stress above room temperature. The theory of Cao and Thouless, based on Weibull statistics, gave the best prediction for the composite ultimate tensile strength.

Gyekenyesi, John Z.↗

Mechanical Properties of Functionally Graded Concrete Lining for Deep Underground Structures

With the mining depth of coal resources increasing, the thickness of traditional lining for deep mines becomes large. The bearing capacity of the outer lining cannot be fully utilized, so a new type of functionally graded lining structure (FGL) with radial Young’s modulus varying in gradient is proposed. In this study, through theoretical analysis and numerical simulation, the mechanical properties of the functionally graded lining were studied, including the characteristics of the elastic working state and the ultimate bearing state. The influences of the structural parameters of the functionally graded lining, including the inner radius, the thickness, Young’s modulus, the compressive strength of the concrete, Poisson’s ratio, and the number of layers on the mechanical properties were analyzed. The calculation formula of the ultimate bearing capacity of the lining and the calculation formula of the maximum tangential strain at the time of lining failure were put forward. The accuracy of the formula was verified by comparing with the numerical simulation results. The research results provide the basis for the construction of the design theory of a functionally graded lining structure and have great engineering significance for the construction of the kilometer-deep mines in the future.

Li, De-Chun↗

Ab-initio calculation of ZnGeAs{sub 2} semiconductor

The structural, electronic, optical and elastic properties of ZnGeAs{sub 2} semiconductor have been investigated using pseudopotential plane wave method within the density functional theory (DFT). The optimized lattice constants, energy gap and crystal field splitting parameter are calculated. The optical properties such as dielectric function, optical reflectivity,, extinction coefficient, absorption spectra, refractive index and electron energy loss spectrum have been studied. The values of bulk modulus (B), elastic constants (C{sub ij}), Young’s modulus (Y), Zener anisotropic factor (A), Poisson’s ratio (ν) and Debye temperature (Θ{sub D}) have been calculated. The calculated values of all these parameters are compared with the available experimental values and the values reported by different workers. A fairly good agreement has been found between them.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Temperature dependent elastic properties of γ-phase U – 8 wt% Mo

Polycrystalline elastic moduli and stiffness tensor components of γ-phase U – 8 wt% Mo have been determined by resonant ultrasound spectroscopy in the temperature range of 25-650°C. The ambient temperature elastic properties are compared to results measured via other experimental methods and show reasonable agreement, though there is considerable variation of these properties within the literature at both the U – 8 wt% Mo composition and as a function of Mo concentration. The Young’s modulus of U – 8 wt% Mo measured in this study decreases steadily with temperature at a rate that is slower than trends previously observed at similar Mo concentrations, though the difference is not statistically significant. This first measurement of the temperature dependent elastic stiffness tensor of a polycrystalline U-Mo alloy clarifies that the behavior of the Young’s modulus is due to a strongly weakening C 11 polycrystalline stiffness tensor component, along with milder decreases in C 12 and C 44 . The unique partially auxetic properties recently predicted for singlecrystalline U-Mo are discussed in regard to their possible impact on the polycrystalline behavior of the alloy.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

Combined quantitative ultrasonic and time-resolved interaction force AFM imaging

The authors describe a method where quantitative ultrasonic atomic force microscopy (UAFM) is achieved during time-resolved interaction force (TRIF) imaging in intermittent contact mode. The method uses a calibration procedure for quantitative UAFM. It improves elasticity measurements of stiff regions of surfaces while retaining the capabilities of the TRIF mode for topography, adhesion, dissipation, and elasticity measurements on soft regions of sample surfaces. This combination is especially advantageous when measuring and imaging samples with broad stiffness range in a nondestructive manner. The experiments utilize an active AFM probe with high bandwidth and the UAFM calibration is performed by measuring the magnitude of the time-resolved UAFM signal at a judiciously chosen frequency for different contact stiffness values during individual taps. Improved sensitivity to stiff surface elasticity is demonstrated on a special sample. The results show that combining UAFM with TRIF provides 2.5 GPa (5%) standard deviation on the silicon surface reduced Young's modulus, representing 5x improvement over using only TRIF mode imaging.

42 ENGINEERING↗

A Coupled Meshless Technique/Molecular Dynamics Approach for Deformation Characterization of Mono-crystalline Metal

This paper presents a multiscale study using the coupled Meshless technique/Molecular Dynamics (M{sup 2}) for exploring the deformation mechanism of mono-crystalline metal (focus on copper) under uniaxial tension. In M{sup 2}, an advanced transition algorithm using transition particles is employed to ensure the compatibility of both displacements and their gradients, and an effective local quasi-continuum approach is also applied to obtain the equivalent continuum strain energy density based on the atomistic potentials and Cauchy-Born rule. The key parameters used in M{sup 2} are firstly investigated using a benchmark problem. Then, M{sup 2} is applied to the multiscale simulation for a mono-crystalline copper bar. It has found that the mono-crystalline copper has very good elongation property, and the ultimate strength and Young's modulus are much higher than those obtained in macro-scale.

36 MATERIALS SCIENCE↗

Impact of Elastic Moduli in Tension and Compression in Geomaterials

Predicting the long-term integrity of caprock is essential for determining the viability of carbon sequestration. Accurate prediction requires incorporating knowledge about small-scale, subcritical fracture and how they contribute to developing micro and macro-cracks. Tests such as short rod, notched three-point bending (N3PB), cylinder splitting, double torsion, etc. are used to determine the physical characteristics of material. Unlike other materials such as metals, geomaterials have different moduli in tension than compression. This study compares the effects of separate tension and compression moduli on simulations in Abaqus for the N3PB test. Previous models of N3PB created by Rhinehart et al. and Borowski have struggled to create results that accurately portrayed experimental results. Borowski found that previous models with only one value for Young's modulus improved when two moduli were used though it was difficult to determine regions of tension and compression prior to simulation. This study develops an Abaqus subroutine written in Fortran to dynamically reassign material properties as the simulation progresses and produces simulation results capable of much better replication of experimental data. However, the accuracy of the model heavily depends on accurate determination of the Young's modulus in tension.

36 MATERIALS SCIENCE↗

Preventing Thin Film Dewetting via Graphene Capping

A monolayer 2D capping layer with high Young's modulus is shown to be able to effectively suppress the dewetting of underlying thin films of small organic semiconductor molecule, polymer, and polycrystalline metal, respectively. To verify the universality of this capping layer approach, the dewetting experiments are performed for single‐layer graphene transferred onto polystyrene (PS), semiconducting thienoazacoronene (EH‐TAC), gold, and also MoS 2 on PS. Thermodynamic modeling indicates that the exceptionally high Young's modulus and surface conformity of 2D capping layers such as graphene and MoS 2 substantially suppress surface fluctuations and thus dewetting. As long as the uncovered area is smaller than the fluctuation wavelength of the thin film in a dewetting process via spinodal decomposition, the dewetting should be suppressed. The 2D monolayer‐capping approach opens up exciting new possibilities to enhance the thermal stability and expands the processing parameters for thin film materials without significantly altering their physical properties.

Cao, Peigen↗

Preparation and mechanical properties of silicon oxycarbide fibers from electrospinning/sol-gel process

Graphical abstract: Ceramic fibers, silicon oxycarbide (SiOC) fibers were demonstrated and showed higher mechanical properties from electrospinning/sol-gel process at 1000 Degree-Sign C. Highlights: Black-Right-Pointing-Pointer SiOC fibers with low cost are promising to substitute the non-oxide fibers. Black-Right-Pointing-Pointer Successful preparation of SiOC fibers by electrospinning/sol-gel process. Black-Right-Pointing-Pointer Confirmation of the designed product using material characterization methods. Black-Right-Pointing-Pointer The SiOC fibers prepared at 1000 Degree-Sign C possess higher strength (967 MPa). -- Abstract: Silicon oxycarbide (SiOC) fibers were produced through the electrospinning of the solution containing vinyltrimethoxysilane and tetraethoxysilane in the course of sol-gel reaction with pyrolysis to ceramic. The effect of the amount of spinning agent Polyvinylpyrrolidone (PVP) on the dope spinnability was investigated. At a mass ratio of PVP/alkoxides = 0.05, the spinning sol exhibited an optimal spinnable time of 50 min and generated a large quantity of fibers. Electrospun fibers were characterized by Fourier transform infrared spectroscopy (FTIR), thermo gravimetric analysis-differential scanning calorimetry (TGA-DSC), scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy (XPS). The SEM results revealed that the SiOC fibers had a smooth surface and dense cross-section, free of residue pores and cracks. The XPS results gave high content of SiC (13.99%) in SiOC fibers. The SiOC fibers prepared at 1000 Degree-Sign C had a high tensile strength of 967 MPa and Young's modulus of 58 GPa.

36 MATERIALS SCIENCE↗

Enhanced properties of graphene/fly ash geopolymeric composite cement

This paper reports for the first time the incorporation of in-situ reduced graphene oxide (rGO) into geopolymers. The resulting rGO–geopolymeric composites are easy to manufacture and exhibit excellent mechanical properties. Geopolymers with graphene oxide (GO) concentrations of 0.00, 0.10, 0.35 and 0.50% by weight were fabricated. The functional groups, morphology, void filling mechanisms and mechanical properties of the composites were determined. The Fourier transform infrared (FTIR) spectra revealed that the alkaline solution reduced the hydroxyl/carbonyl groups of GO by deoxygenation and/or dehydration. Concomitantly, the spectral absorbance related to silica type cross-linking increased in the spectra. The scanning electron microscope (SEM) micrographs indicated that rGO altered the morphology of geopolymers from a porous nature to a substantially pore filled morphology with increased mechanical properties. The flexural tests showed that 0.35-wt.% rGO produced the highest flexural strength, Young's modulus and flexural toughness and they were increased by 134%, 376% and 56%, respectively.

36 MATERIALS SCIENCE↗