Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Wind speed”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Quiet High Speed Fan II (22-inch) Duct Mode Characteristics as Measured by the Rotating Rake Mode Measurement System while Operated in the NASA Glenn 9x15 Low Speed Wind Tunnel

Wind Tunnel test at a tunnel Mach number of 0.10. This was an entry to investigate the effect of “stator clocking” on noise. The fan consisted of a moderately aft swept rotor and an aft swept set of stator vanes. The fan stage consisted of 22 rotor blades, 50 stator vanes, and 10 downstream support struts. A set of stator vanes designed for lower noise was tested as well as a baseline stator vane set. The stator assembly could be rotated several degrees to adjust the clocking angle between the stator vane pack and the strut assembly. All configurations were with a hard wall duct (no acoustic treatment). The NASA Glenn Research Center’s Rotating Rake Mode Measurement System was utilized to obtain a complete map of the acoustic duct modes present in the ducted fan. The system is a radial rake emersed into the duct that continuously rotates about the duct centerline. For the two stator configurations, data were acquired at several different fan speeds which included nominal, approach, cutback, and takeoff conditions. Analysis of the mode power level results at the fan fundamentals showed the improved designed set resulted in lower rotor-stator and rotor-strut interaction acoustic levels for the interaction modes. Varying the angle between the stators and struts was shown to be a viable method to achieve a minimum in rotor-strut interaction mode power level. Multiple-pure-tones generated by the Quiet High Speed Fan II in the inlet were also measured.

Turbofan, Duct Modes↗
NASA NTRS1971

Improved smoke generator for low-speed wind tunnels

Device incorporates kerosene vaporization concept by electrically heating tubes that carry kerosene down the probe, smoke is emitted from orifices at probe's end. Neither the low concentration of kerosene vapor nor the 50 Vdc power supply constitutes a safety hazard.

Turner, T. R.↗
NASA NTRS1973

Results of investigations on a 0.0405 scale model ATP version of the NR-SSV orbiter in the North American Aeronautical Laboratory low speed wind tunnel

Experimental aerodynamic investigations were conducted on a scale model space shuttle vehicle (SSV) orbiter. The purpose of the test was to investigate the longitudinal and lateral-directional aerodynamic characteristics. Emphasis was placed on model component, wing-glove, and wing-body fairing effects, as well as elevon, aileron, and rudder control effectiveness. Angles of attack from - 5 deg to + 30 deg and angles of sideslip from - 5 deg to + 10 deg were tested. Static pressures were recorded on base, fuselage, and wing surfaces. Tufts and talc-kerosene flow visualization techniques were also utilized. The aerodynamic force balance results are presented in plotted and tabular form.

Mennell, R.↗
NASA NTRS1973

A low speed wind tunnel test of the 0.050 scale NASA-JSC shuttle orbiter 089B to determine the longitudinal and lateral directional effects of control surface modifications

Wind tunnel tests to determine the longitudinal and lateral-directional effects of control surface modifications on the space shuttle orbiter aerodynamic characteristics are discussed. A total of 103 data runs were made which consisted of pitch runs through a range of zero to 28 degrees at a zero yaw angle and yaw runs from minus 6 to plus 6 degrees at various fixed pitch angles. At each data point, data from an internal strain gage balance was sampled with the digital data system. Also recorded were the model angles of pitch and yaw and the test section static pressure. Results are presented in the form of tabulated aerodynamic coefficient data about the model reference center.

Oldenbuttel, R. H.↗
NASA NTRS1974

Low speed wind tunnel tests of a 1/9-scale model of a variable-sweep advanced supersonic transport

Tests have been conducted in the Langley full-scale tunnel to determine the aerodynamic characteristics of a 1/9-scale variable-sweep advanced supersonic transport configuration. The model configurations investigated were the basic unflapped arrangement, and a takeoff and landing flap arrangement with several strake leading edge flow control devices. The tests were conducted for an angle-of-attack range from about minus 5 deg to 36 deg and a sideslip range from minus 5 deg to 10 deg. The tests were conducted for a range of Reynolds number from 3.92 million to 5.95 million corresponding to test velocities of about 54.5 knots and 81.7 knots, respectively.

Mclemore, H. C.↗
NASA NTRS1974

Low-speed wind tunnel tests of a 50.8-centimeter (20-in.) 1.15-pressure-ratio fan engine model

At a typical STOL aircraft takeoff and landing velocity, wind tunnel aerodynamic and acoustic measurements demonstrated that an inlet lip-area contraction ratio of 1.35 was superior to a ratio of 1.26 at high incidence angles. A 17 percent reduction in net thrust and an increase of 9 decibels in sound pressure level at the blade passing frequency resulted from inlet flow separation at an incidence angle of 50 deg with the 1.26-contraction-ratio inlet. Reverse-thrust forces obtained with blade rotation through the feathered angle were 1.8 times larger than with blade rotation through the flat angle. Reverse-thrust force was reduced from 30 to 50 percent and sound pressure level increased from 3 to 7 decibels at the blade passing frequency between the wind-tunnel-off condition and a typical STOL aircraft landing velocity.

Wesoky, H. L.↗
NASA NTRS1974

Aerodynamic investigations into various low speed L/D improvement devices on the 140A/B space shuttle orbiter configuration in the Rockwell International low speed wind tunnel (OA86)

Tests were conducted to investigate various base drag reduction techniques in an attempt to improve Orbiter lift-to-drag ratios and to calculate sting interference effects on the Orbiter aerodynamic characteristics. Test conditions and facilites, and model dimensional data are presented along with the data reduction guidelines and data set/run number collation used for the studies. Aerodynamic force and moment data and the results of stability and control tests are also given.

Mennell, R. C.↗
NASA NTRS1974

Results of investigations on an 0.015 scale 140A/B configuration space shuttle vehicle orbiter model (49-0) in the LTV 4 by 4-foot high speed wind tunnel (0A84)

Data obtained from a wind tunnel test of an 0.015-scale 140 A/B configuration space shuttle vehicle orbiter model (49-0) are presented. Runs were conducted at Mach numbers 0.6, 0.9, 1.2, 1.6, and 2.0 and Reynolds numbers of 8.4, 9.0, 9.0, 10.9, and 13.6 million per foot respectively. Various control surface settings were investigated from angles of attack of minus 4 degrees to plus 30 degrees at fixed angles of sideslip of zero and minus 5 degrees and through angles of sideslip from minus 2 to plus 8 degrees at fixed angles of attack of zero, plus 10, plus 15, and plus 20 degrees. The purpose of the test was to define the longitudinal and lateral-directional stability and control characteristics for the updated SSV configuration.

Esparza, V.↗
NASA NTRS1975

Space shuttle vehicle ferry configuration afterbody fairing effects on 140A/B orbiter aerodynamic characteristics using an .0405 scale model orbiter (43-0) in the Rockwell International 7.75 x 11 ft low speed wind tunnel (OA123)

The primary test objectives were to define ferry configuration afterbody fairing effects on orbiter stability and control characteristics and to substantiate wind tunnel results. Parametric variations consisted entirely of testing different afterbody fairing contours in an effort to improve both the orbiter drag levels and lateral-directional control characteristics. The three afterbody contours that were tested consisted of the Boeing TC3 beavertail, the new Rockwell-Boeing TC4 fairing, and a modification of an existing short bumblebee fairing redesignated TC6.

Mennell, R. C.↗
NASA NTRS1975

Correlation of low speed wind tunnel and flight test data for V/STOL aircraft

The XV-5B fan-in-wing aircraft and the Y0V-10 RCF rotating cylinder flap aircraft were subjected to wind tunnel tests. These tests were conducted specifically to provide for correlation between wind tunnel and inflight aerodynamics and noise test data. Correlation between aerodynamic and noise data are presented and testing techniques that are related to the accuracy of the data, or that might affect the correlations, are discussed.

Cook, W. L.↗
NASA NTRS1976

Measurement of model propulsion system noise in a low-speed wind tunnel

Methods are presented for making overall and directional acoustic measurements with forward velocity in the Lewis 9 x 15 V/STOL wind tunnel. Overall acoustic measurements are discussed; the acoustic calibration methods, instrumentation features, and types of experiments are presented. Selected data are presented as examples of the various types of overall measurements that are possible. The method of making directional acoustic measurements is presented, and the necessary alterations to the tunnel, specialized acoustic instrumentation, and calibration details are described. The results indicate that relative overall acoustic measurements can be made successfully and that directional acoustic measurements are feasible.

Diedrich, J. H.↗
NASA NTRS1975

Low speed wind tunnel investigation of span load alteration, forward-located spoilers, and splines as trailing-vortex-hazard alleviation devices on a transport aircraft model

The effectiveness of a forward-located spoiler, a spline, and span load alteration due to a flap configuration change as trailing-vortex-hazard alleviation methods was investigated. For the transport aircraft model in the normal approach configuration, the results indicate that either a forward-located spoiler or a spline is effective in reducing the trailing-vortex hazard. The results also indicate that large changes in span loading, due to retraction of the outboard flap, may be an effective method of reducing the trailing-vortex hazard.

Croom, D. R.↗