Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “W”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Analysis of W. F. Durand's and E. P. Lesley's propeller tests

This report is a critical study of the results of propeller model tests with the view of obtaining a clear insight into the mechanism of the propeller action and of examining the soundness of the physical explanation generally given. The nominal slip-stream velocity is plotted against the propeller tip velocity, both measured by the velocity of flight as a unit. Within the range corresponding to conditions of flight, the curve thus obtained is a straight line. Its inclination depends chiefly on the effective blade width, its position on the effective pitch. These two quantities can therefore be determined from the result of each propeller test. Both can easily be estimated therefrom for new propellers of similar type. Thus, a simple method for the computation of propellers suggests itself.

Munk, Max M↗

The D.V.L. Gliding-angle Control : W. Hubner Design

This report describes a device for arbitrary enlargement of the gliding angle of airplanes, especially of such with flat gliding angle and difficult landing characteristics. The D.V.L. gliding angle control (design, Hubner) permits a local interruption of the lift distribution along the span and consequently an increased induced drag. The mechanism comprises two wing rudders operated by lever from the pilot's cockpit. Said rudders are fitted on the top side of the wing near the leading edge. The displacement of these rudders results in a separation of the air flow on the top side of the wing.

Hubner, Walter↗

Transport phenomena in stratified multi-fluid flo w in the presence and absence of gravity

An experiment is being conducted to study the effects of buoyancy on planar stratified flows. A wind tunnel has been designed and constructed to generate planar flows with separate heating for the top and bottom planar air jets emerging from slot nozzles separated by an insulating splitter plate. The objective is to generate planar jet flows with well defined and well controlled velocity and temperature profiles. Magnitudes of velocity and temperature will be varied separately in each flow for both laminar and turbulent flow conditions. Both stably and unstably stratified flows will be studied by changing the temperature distributions in each air stream. This paper reports on the design of the apparatus and initial measurements of velocity and turbulence made by laser Doppler velocimetry.

Chigier, Norman↗

Sampling Elysium lavas (13 deg N, 203 deg W)

The proposed Pathfinder landing site presents the opportunity to determine chemical and mineralogical compositions of an Elysium lava flow. The flow is part of a geologic unit of planetary significance. The proposed site appears suitable for landing, and lava surfaces should be accessible to the Pathfinder instruments. By analogy to terrestrial flood basalts, any lava analyzed by Pathfinder is likely to be representative of the entire Elysium province.

Allen, Carlton C.↗

Calculated quantum yield of photosynthesis of phytoplankton in the Marine Light-Mixed Layers (59 deg N, 21 deg W)

The quantum yield of photosynthesis (mol C/mol photons) was calculated at six depths for the waters of the Marine Light-Mixed Layer (MLML) cruise of May 1991. As there were photosynthetically available radiation (PAR) but no spectral irradiance measurements for the primary production incubations, three ways are presented here for the calculation of the absorbed photons (AP) by phytoplankton for the purpose of calculating phi. The first is based on a simple, nonspectral model; the second is based on a nonlinear regression using measured PAR values with depth; and the third is derived through remote sensing measurements. We show that the results of phi calculated using the nonlinear regreesion method and those using remote sensing are in good agreement with each other, and are consistent with the reported values of other studies. In deep waters, however, the simple nonspectral model may cause quantum yield values much higher than theoretically possible.

Carder, K. L.↗

The minimum mass ratio of W Ursae Majoris binaries

The minimum mass ratio for tidal stability of a contact binary containing two unevolved main-sequence stars is calculated to be q(sub min) approximately =0.09 in the case of a mostly radiative primary, and it is higher if an appreciable fraction of the mass lies in a convective envelope. At least one observed system, AW UMa, has a mass ratio just below this value (q = 0.075), implying that, if the system is stable, the primary must be slightly evolved and must have a very shallow convective envelope. Contact binaries with mass ratios significantly below that of AW UMa should not be observed, since they are tidally unstable and quickly merge into a single, rapidly rotating object, on a timescale approximately 10(exp 3)-10(exp 4) yr.

Rasio, Frederic A.↗

Observation of the middle atmospheric thermal tides using lidar measurements over Mauna Loa Observatory (19.5 deg N, 155.6 deg W)

Temperature measurements in the middle atmosphere using Rayleigh lidars have been performed for several decades now. The high accuracy and vertical resolution provided by lidars allow to study the temperature variability at various scales with high confidence levels. One of the numerous applications is the study of the middle atmospheric thermal tides. Although Rayleigh lidar measurements are basically possible only at nighttime, diurnal and semidiurnal components can often be extracted if the results are taken with care and correctly interpreted. Using results from more than 200 hours of nighttime measurements obtained by lidar in October 1996 and 1997 at Mauna Loa Observatory, Hawaii, a study of the middle atmospheric (25-90 km) thermal tides is presented in this paper. The amplitudes and phases of the diurnal and semidiurnal components were calculated for some altitudes where the fits converged significantly, and compared to that of the Global Scale Wave Model (GSWM).

Leblanc, Thierry↗

HST Observations of New Horizontal Branch Structures in the Globular Cluster w Centauri

The globular cluster omega Centauri contains the largest known population of very hot horizontal branch (HB) stars. We have used the Hubble Space Telescope to obtain a far-UV/optical color-magnitude diagram of three fields in omega Cen. We find that over 30% of the HB objects are "extreme" HB or hot post-HB stars. A wide gap in the color distribution of the hot HB stars may correspond to gaps found earlier in several other clusters, which argues for a common mass loss mechanism. The diagram contains a significant population of hot sub-HB stars, which we interpret as the "blue-hook" objects predicted by D'Cruz (1996a). These are produced by late He-flashes in stars which have undergone unusually large giant branch mass loss. Omega Cen has a well-known spread of metal abundance, and the diagram is consistent with a giant branch mass loss efficiency which increases with metallicity. There is no evidence for a dynamical origin of the hot HB stars.

Stecher, Theodore↗

Comparative Wide Temperature Core Loss Characteristics of Two Candidate Ferrites for the NASA/TRW 1500 W PEBB Converter

High frequency core loss and magnetization properties of commercial type MN8CX and PC40, high resistivity, MnZn based, power ferrites are presented over the temperature range of -l50 C to 150 C, at selected values of peak flux density (B (sub p)). Most of the data is at 100 kHz, with some data extended to 200 and 300 kHz for the MN8CX. Plots of the specific Core loss against temperature exhibit the minimal characteristic of such ferrites. These plots show that the MN8CX is optimized for minimum loss at about 25 C, whereas the PC40 is optimized at about 80 C. At the points of minimum loss and for the same B (sub p), the MN8CX has roughly half the losses of the PC40 at the lower flux densities. This loss ratio continues down to cryogenic temperatures. However, above about 80 C the losses are practically equal. The lowest 100 kHz loss recorded, 50 mW/cm3 for the MNGCX at a B (sub p) of 0.1T, equals that of a very low loss, Co based, transverse magnetically annealed, amorphous ribbon material. Except possibly at lower B (sub p) or much higher frequencies, these ferrites are not competitive for low losses over a wide temperature range with certain specialty amorphous materials. Permeability is computed from a linear model, plots against temperature are presented and again compared to the specialty amorphous materials.

Niedra, Janis M.↗

W-Band InP Wideband MMIC LNA with 30K Noise Temperature

This paper describe a millimeter wave low noise amplifier with extraordinary low noise, low consumption, and wide frequency range. These results are achieved utilizing state-of-the-art InP HEMT transistors coupled with CPW circuit design. The paper describes the transistor models, modeled and measured on-wafer and in-module results at both 300K am 24K operating temperatures for many samples of the device.

Weinreb, S.↗

The Confluence of Gangis and Eos Chasmas (5-12 deg S, 31-41 deg W): Geologic, Hydrologic, and Exobiologic Considerations for Landing Site at the East End of Valles Marineris

Over its 3,500 km length, Valles Marineris exhibits an enormous range of geologic and environmental diversity. At its western end, the canyon is dominated by the tectonic complex of Noctis Labyrinthus; while in the east it grades into an extensive region of chaos where scoured channels and streamlined islands provide evidence of catastrophic floods that spilled into the northern plains. In the central portion of the system, debris derived from the massive interior layered deposits of Candor and Ophir Chasmas spills into the central trough. In other areas, 6 km-deep exposures of Hesperian and Noachian-age canyon wall stratigraphy have collapsed in massive landslides that extend many tens of kilometers across the canyon floor. Ejecta from interior craters, aeolian sediments, and possible volcanics emanating from structurally controlled vents along the base of the scarps, further contribute to the canyon's geologic complexity. Following the initial rifting that gave birth to Valles Marineris, water appears to have been a principal agent in the canyon's geomorphic development an agent whose significance is given added weight by its potential role in both sustaining and preserving evidence of past life. In this regard, the interior layered deposits of Candor, Ophir, and Hebes Chasmas, have been identified as possible lucustrine sediments that may have been laid down in long-standing ice-covered lakes. The potential survival and growth of native organisms in such an environment, or in the aquifers whose disruption gave birth to the chaotic terrain and outflow channels to the north and east of the canyon, raises the possibility that fossil indicators of life may be present in the local sediment and rock. Because of the enormous distances over which these diverse environments occur, identifying a single landing site that maximizes the opportunity for scientific return is not a simple task. However, given the fluvial history and narrow geometry of the canyon, the presence of a single exit at its eastern end provides an opportunity for sampling that appears unequaled elsewhere in the system.

George, J. A.↗

Book Review: A Thin Cosmic Rain by Michael W. Friedlander

In reviewing this book I am going to say some harsh things about it. From this one might think that I did not like the book. In fact, one would be wrong to think so. For this reason I wish to state up front that I did like the book. It was an ambitious undertaking and I think that the author has, for the most part, pulled it off. This extremely broad and rich book will allow those non-specialists with a sufficiently long attention span to obtain a good understanding of what cosmic rays are and what cosmic ray research is all about. I have pointed out things that bothered me because I believe that the book is good enough for a second edition and I hope that these matters can be addressed at that time.

Jones, Frank C.↗

Metal/Silicate Partitioning of P, Ga, and W at High Pressures and Temperatures: Dependence on Silicate Melt Composition

The distinctive pattern of element concentrations in the upper mantle provides essential evidence in our attempts to understand the accretion and differentiation of the Earth (e.g., Drake and Righter, 2002; Jones and Drake, 1986; Righter et al., 1997; Wanke 1981). Core formation is best investigated through use of metal/silicate partition coefficients for siderophile elements. The variables influencing partition coefficients are temperature, pressure, the major element compositions of the silicate and metal phases, and oxygen fugacity. Examples of studies investigating the effects of these variables on partitioning behavior are: composition of the metal phase by Capobianco et al. (1999) and Righter et al. (1997); silicate melt composition by Watson (1976), Walter and Thibault (1995), Hillgren et al. (1996), Jana and Walker (1997), and Jaeger and Drake (2000); and oxygen fugacity by Capobianco et al. (1999), and Walter and Thibault (1995). Here we address the relative influences of silicate melt composition, pressure and temperature.

Bailey, Edward↗

Reply by the Authors to C. K. W. Tam

The prediction of noise generation and radiation by turbulence has been the subject of continuous research for over fifty years. The essential problem is how to model the noise sources when one s knowledge of the detailed space-time properties of the turbulence is limited. We attempted to provide a comparison of models based on acoustic analogies and recent alternative models. Our goal was to demonstrate that the predictive capabilities of any model are based on the choice of the turbulence property that is modeled as a source of noise. Our general definition of an acoustic analogy is a rearrangement of the equations of motion into the form L(u) = Q, where L is a linear operator that reduces to an acoustic propagation operator outside a region upsilon; u is a variable that reduces to acoustic pressure (or a related linear acoustic variable) outside upsilon; and Q is a source term that can be meaningfully estimated without knowing u and tends to zero outside upsilon.

Morris, Philip J.↗

C-O-H ratios of silicate melt inclusions in basalts from the Galapagos Spreading Center near 95 degrees W: a laser decrepitation mass spectrometry study

Volatile ratios (primarily of H2O and CO2) in individual silicate melt (glass) inclusions in minerals have been analyzed using laser volatilization and mass spectrometry. A Nd-glass laser was used to produce 50-micrometer diameter pits in silicate melt inclusions. Released volatiles were analyzed directly with a computer-controlled quadrupole mass spectrometer. The detection limits for CO2 and H2O were on the order of 3 x 10(-14) and 3 x 10(-13) moles, respectively. The reproducibility for CO2/H2O was better than +/- 9%. The total range of volatile ratios from vitreous silicate glass inclusions contained in a suite of Galapagos lavas were: 0.018 to 1.193 for CO2/H2O; 0.002 to 0.758 for CO/H2O; 0 to 0.454 for CH4/H2O; and 0 to 0.432 for Ar/H2O. The mean CO2/H2O from the propagating rift (0.245 +/- 0.068) silicate glass inclusions is significantly lower than that of the actively failing rift (0.641 +/- 0.241); this difference probably reflects different degrees of degassing during magmatic histories for the two regions. Relatively undifferentiated failing rift magmas must have relatively short crustal residence times prior to eruption and, therefore, have not undergone significant degassing of CO2, as would appear to be the case for the more highly fractionated propagating rift magmas. The laser-mass spectrometric system described herein has the ability to act as a point-source probing device that can differentiate between the various volatile sites in minerals and rocks (as well as synthetic materials) on a micrometer scale.

NASA Discipline Exobiology↗

High Precision Metrology on the Ultra-Lightweight W 50.8 cm f/1.25 Parabolic SHARPI Primary Mirror using a CGH Null Lens

For potential use on the SHARPI mission, Eastman Kodak has delivered a 50.8cm CA f/1.25 ultra-lightweight UV parabolic mirror with a surface figure error requirement of 6nm RMS. We address the challenges involved in verifying and mapping the surface error of this large lightweight mirror to +/-3nm using a diffractive CGH null lens. Of main concern is removal of large systematic errors resulting from surface deflections of the mirror due to gravity as well as smaller contributions from system misalignment and reference optic errors. We present our efforts to characterize these errors and remove their wavefront error contribution in post-processing as well as minimizing the uncertainty these calculations introduce. Data from Kodak and preliminary measurements from NASA Goddard will be included.

Antonille, Scott↗

Results From a Parametric Acoustic Liner Experiment Using P and W GEN1 HSR Mixer/Ejector Model

This report documents the results of an acoustic liner test performed using a Gen 1 HSR mixer/ejector model installed on the Jet Exit Rig in the Nozzle Acoustic Test Rig in the Aeroacoustic Propulsion Laboratory or NASA Glenn Research Center. Acoustic liner effectiveness and single-component thrust performance results are discussed. Results from 26 different types of single-degree-of-freedom and bulk material liners are compared with each other and against a hardwall baseline. Design parameters involving all aspects of the facesheet, the backing cavity, and the type of bulk material were varied in order to study the effects of these design features on the acoustic impedance, acoustic effectiveness and on nozzle thrust performance. Overall, the bulk absorber liners are more effective at reducing the jet noise than the single-degree-of-freedom liners. Many of the design parameters had little effect on acoustic effectiveness, such as facesheeet hole diameter and honeycomb cell size. A relatively large variation in the impedance of the bulk absorber in a bulk liner is required to have a significant impact on the noise reduction. The thrust results exhibit a number of consistent trends, supporting the validity of this new addition to the facility. In general, the thrust results indicate that thrust performance benefits from increased facesheet thickness and decreased facesheet porosity.

Boyd, Kathleen C.↗