Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solidification microstructures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Advanced powder metallurgy aluminum alloys via rapid solidification technology, phase 2

Marko's rapid solidification technology was applied to processing high strength aluminum alloys. Four classes of alloys, namely, Al-Li based (class 1), 2124 type (class 2), high temperature Al-Fe-Mo (class 3), and PM X7091 type (class 4) alloy, were produced as melt-spun ribbons. The ribbons were pulverized, cold compacted, hot-degassed, and consolidated through single or double stage extrusion. The mechanical properties of all four classes of alloys were measured at room and elevated temperatures and their microstructures were investigated optically and through electron microscopy. The microstructure of class 1 Al-Li-Mg alloy was predominantly unrecrystallized due to Zr addition. Yield strengths to the order of 50 Ksi were obtained, but tensile elongation in most cases remained below 2 percent. The class 2 alloys were modified composition of 2124 aluminum alloy, through addition of 0.6 weight percent Zr and 1 weight percent Ni. Nickel addition gave rise to a fine dispersion of intermetallic particles resisting coarsening during elevated temperature exposure. The class 2 alloy showed good combination of tensile strength and ductility and retained high strength after 1000 hour exposure at 177 C. The class 3 Al-Fe-Mo alloy showed high strength and good ductility both at room and high temperatures. The yield and tensile strength of class 4 alloy exceeded those of the commercial 7075 aluminum alloy.

Ray, Ranjan↗

Magnetization of small iron-nickel spheres

Magnetic properties of small iron-nickel alloy spheres, having compositions which cover the entire Fe-Ni binary, are presented. The spheres were formed during solidification in free fall following the melting of electropolished wires of appropriate composition. The spheres with Ni not greater than 25% acquired a martensitic thermal remanence while those with Ni not less than 30% acquired a thermoremanent magnetization. A magnetic remanence-composition diagram and a coercive force-composition diagram are constructed. Magnetic hysteresis loops and derived parameters demonstrate the difference between metal-bearing and oxide-bearing natural samples. The magnetic remanence varies as the sphere size in conjunction with the microstructure. These results help to explain why coercive force is generally low, remanent coercive force is generally high, and their ratio (R/C) is always large in fine metal dispersions, such as lunar samples and chondrite meteorites.

Wasilewski, P.↗

Analysis of the solidified structure of rheocast and VADER processed nickel-base superalloy

Conventional 'ingot' processing of highly alloyed compositions results in a cast product which suffers from extensive macrosegregation, hot tears, and heterogeneities. By controlling the solidification journey, one can produce a fine grained cast product. This is achieved by manipulating the melt in the mushy zone. Rheocasting and vacuum arc double electrode remelting (VADER) are two such technologies where the melt is processed in the mushy zone. IN-100, a nickel based superalloy, was rheocast as well as VADER processed. The resultant cast structures are analyzed, compared and discussed both onmicro- and macrostructural levels. The effect of the rheocast processing variables (stirring seed, time and temperature) on the cast microstructure are also discussed.

Apelian, D.↗

Micro and Macro Segregation in Alloys Solidifying with Equiaxed Morphology

To understand macro segregation formation in Al-Cu alloys, experiments were run under terrestrial gravity (1g) and under low gravity during parabolic flights (10(exp -2) g). Alloys of two different compositions (2% and 5% Cu) were solidified at two different cooling rates. Systematic microscopic and SEM observations produced microstructural and segregation maps for all samples. These maps may be used as benchmark experiments for validation of microstructure evolution and segregation models. As expected, the macro segregation maps are very complex. When segregation was measured along the central axis of the sample, the highest macro segregation for samples solidified at 1g was obtained for the lowest cooling rate. This behavior is attributed to the longer time available for natural convection and shrinkage flow to affect solute redistribution. In samples solidified under low-g, the highest macro-segregation was obtained at the highest cooling rate. In general, low-gravity solidification resulted in less segregation. To explain the experimental findings, an analytical (Flemings-Nereo) and a numerical model were used. For the numerical model, the continuum formulation was employed to describe the macroscopic transports of mass, energy, and momentum, associated with the microscopic transport phenomena, for a two-phase system. The model proposed considers that liquid flow is driven by thermal and solutal buoyancy, and by solidification shrinkage. The Flemings-Nereo model explains well macro segregation in the initial stages of low-gravity segregation. The numerical model can describe the complex macro segregation pattern and the differences between low- and high-gravity solidification.

Stefanescu, Doru M.↗

Undercooling, Liquid Separation and Solidification of Cu-Co Alloys

Large undercooling can induce not only various solidification pathways, but also a precursor reaction, or liquid separation. This paper deals with the latter effect of undercooling using examples of the Cu-Co system which has a flattened liquidus. Bulk Cu-Co alloys (about 7mm diameter) at compositions ranging from 10 to 90 wt pct Co were highly undercooled using a fluxing technique. Except for Cu-90 wt pct Co, liquid separation was directly observed as undercooling exceeded a critical value depending on the composition. It was also confirmed by a microstructural transition from dendrites to droplets above the critical undercooling. Finally, theoretical calculations regarding the metastable miscibility boundary and maximum droplet radius were made to analyze the experimental results.

Robinson, M. B.↗

Rapid solidification of high-conductivity copper alloys

The main objective was to develop improved copper alloys of high strength and high thermal and electric conductivity. Chill block melt spinning was used to produce binary alloys of Cu-Cr and Cu-Zr, and ternary alloys of Cu-Cr-Ag. By quenching from the liquid state, up to 5 atomic percent of Cr and Zr were retained in metastable extended solid solution during the rapid solidification process. Eutectic solidification was avoided and the full strengthening benefits of the large volume fraction of precipitates were realized by subsequent aging treatment. The very low solid solubility of Cr and Zr in Cu result in a high conductivity Cu matrix strengthened by second phase precipitates. Tensile properties on as-cast and aged ribbons were measured at room and elevated temperatures. Precipitate coarsening of Cr in Cu was studied by changes in electrical resistance during aging. X-ray diffraction was used to measure the lattice parameter and the degree of supersaturation of the matrix. The microstructures were characterized by optical and electron microscopy.

Bloom, Theodore Atlas↗

Materials science research in microgravity

There are several important attributes of an extended duration microgravity environment that offer a new dimension in the control of the microstructure, processing, and properties of materials. First, when gravitational effects are minimized, buoyancy driven convection flows are also minimized. The flows due to density differences, brought about either by composition or temperature gradients will then be reduced or eliminated to permit a more precise control of the temperature and the composition of a melt which is critical in achieving high quality crystal growth of electronic materials or alloy structures. Secondly, body force effects such as sedimentation, hydrostatic pressure, and deformation are similarly reduced. These effects may interfere with attempts to produce uniformly dispersed or aligned second phases during melt solidification. Thirdly, operating in a microgravity environment will facilitate the containerless processing of melts to eliminate the limitations of containment for reactive melts. The noncontacting forces such as those developed from electromagnet, electrostatic, or acoustic fields can be used to position samples. With this mode of operation, contamination can be minimized to enable the study of reactive melts and to eliminate extraneous crystal nucleation so that novel crystalline structures and new glass compositions may be produced. In order to take advantage of the microgravity environment for materials research, it has become clear that reliable processing models based on a sound ground based experimental experience and an established thermophysical property data base are essential.

Perepezko, John H.↗

Micromechanical Characterization and Texture Analysis of Direct Cast Titanium Alloys Strips

This research was conducted to determine a post-processing technique to optimize mechanical and material properties of a number of Titanium based alloys and aluminides processed via Melt Overflow Solidification Technique (MORST). This technique was developed by NASA for the development of thin sheet titanium and titanium aluminides used in high temperature applications. The materials investigated in this study included conventional titanium alloy strips and foils, Ti-1100, Ti-24Al-11Nb (Alpha-2), and Ti-48Al-2Ta (Gamma). The methodology used included micro-characterization, heat-treatment, mechanical processing and mechanical testing. Characterization techniques included optical, electron microscopy, and x-ray texture analysis. The processing included heat-treatment and mechanical deformation through cold rolling. The initial as-cast materials were evaluated for their microstructure and mechanical properties. Different heat-treatment and rolling steps were chosen to process these materials. The properties were evaluated further and a processing relationship was established in order to obtain an optimum processing condition. The results showed that the as-cast material exhibited a Widmanstatten (fine grain) microstructure that developed into a microstructure with larger grains through processing steps. The texture intensity showed little change for all processing performed in this investigation.

Source record↗

Containerless low gravity processing of glass forming and immiscible alloys

Under normal one-g conditions immiscible alloys segregate extensively during solidification due to sedimentation of the more dense of the immiscible liquid phases. Immiscible (hypermonotectic) gold-rhodium alloys were processed in the 100 meter drop tube under low gravity, containerless conditions to determine the feasibility of producing dispersed structures. Three alloy compositions were utilized. Alloys containing 10 percent by volume of the gold-rich hypermonotectic phase exhibited a tendency for the gold-rich liquid to wet the outer surface of the samples. This wetting tendency led to extensive segregation in several cases. Alloys containing 80 and 90 percent by volume of the gold-rich phase possessed completely different microstructures from the 10 percent samples when processed under low-g, containerless conditions. Several samples exhibited microstructures consisting of well dispersed 2 to 3 microns diameter rhodium-rich spheres in a gold-rich matrix.

Andrews, J. Barry↗

A laboratory means to produce tough aluminum sheet from powder

The rapid solidification of aluminum alloys as powder and the subsequent fabrication processes can be used to develop and tailor alloys to satisfy specific aerospace design requirements, including high strength and toughness. Laboratory procedures to produce aluminum powder-metallurgy (PM) materials are efficient but require evidence that the laboratory methods used can produce a product with superior properties. This paper describes laboratory equipment and procedures which can be used to produce tough aluminum PM sheet. The processing of a 2124 + 0.9 percent Zr aluminum alloy powder is used as an example. The fully hardened sheet product is evaluated in terms of properties and microstructure. The key features of the vacuum hot press pressing operation used to consolidate the powder are described. The 2124 + 0.9 percent Zr - T8 temper aluminum sheet produced was both strong (460-490 MPa yield strength) and tough (Kahn Tear unit-propagation- energy values over three times those typical for ingot metallurgy 2024-T81). Both the longitudinal and longitudinal-transverse directions of the sheet were tested. The microstructure was well refined with subgrains of one or two micrometers. Fine dispersoids of Al3Zr in the precipitate free regions adjacent to boundaries are believed to contribute to the improved toughness.

Singleton, O. R.↗

The Tucson meteorite

Tucson is an unusual iron meteorite which contains highly reduced silicate inclusions and elemental silicon and chromium in solution. The metal matrix of Tucson was found to be chemically uniform, suggesting that homogenization has occurred at elevated temperatures. The microstructure of the metal consists of plessite and thin ribbons of kamacite. Nickel and phosphorus concentrations indicate that kamacite nucleated along prior taenite grain boundaries at about 650 C, and grew upon cooling to 500 C. Kamacite growth calculations show that Tucson cooled at about 1 C/1000 yr, a rate which corresponds to a depth of burial at the center of a 15-km-radius parent body or closer to the surface of parent bodies of larger sizes. The shapes of the Tucson irons, and the presence and distribution of silicate inclusions in the Fe-Ni matrix appear to be a result of a solidification process.

Miyake, G. T.↗

Producing Foils From Direct Cast Titanium Alloy Strip

This research was undertaken to demonstrate the feasibility of producing high-quality, thin-gage, titanium foil from direct cast titanium strip. Melt Overflow Rapid Solidification Technology (MORST) was used to cast several different titanium alloys into 500 microns thick strip, 10 cm wide and up to 3 m long. The strip was then either ground, hot pack rolled or cold rolled, as appropriate, into foil. Gamma titanium aluminide (TiAl) was cast and ground to approximately 100 microns thick foil and alpha-2 titanium aluminide (Ti3AI) was cast and hot pack rolled to approximately 70 microns thick foil. CP Ti, Ti6Al2Sn4Zr2Mo, and Ti22AI23Nb (Orthorhombic), were successfully cast and cold-rolled into good quality foil (less than 125 microns thick). The foils were generally fully dense with smooth surfaces, had fine, uniform microstructures, and demonstrated mechanical properties equivalent to conventionally produced titanium. By eliminating many manufacturing steps, this technology has the potential to produce thin gage, titanium foil with good engineering properties at significantly reduced cost relative to conventional ingot metallurgy processing.

Stuart, T. A.↗

Use of Microgravity to Control the Microstructure of Eutectics

This grant began in June of 1996. Its long term goal is to be able to control the microstructure of directionally solidified eutectic alloys, through an improved understanding of the influence of convection. The primary objective of the projects in the present grant is to test hypotheses for the reported influence of microgravity on the microstructure of eutectics. The prior experimental results on the influence of microgravity on the microstructure of eutectics have been contradictory. With lamellar eutectics, microgravity had a negligible effect on the microstructure. Microgravity experiments with fibrous eutectics sometimes showed a finer microstructure and sometimes a coarser microstructure. Most research has been done on the MnBi/Bi rod-like eutectic. Larson and Pirich obtained a two-fold finer microstructure both from microgravity and by use of a magnetic field to quench buoyancy-driven convection. Smith, on the other hand, observed no change in microgravity. Prior theoretical work at Clarkson University showed that buoyancy-driven convection in the vertical Bridgman configuration is not vigorous enough to alter the concentration field in front of a growing eutectic sufficiently to cause a measurable change in microstructure. We assumed that the bulk melt was at the eutectic composition and that freezing occurred at the extremum, i.e. with minimum total undercooling at the freezing interface. There have been four hypotheses attempting to explain the observed changes in microstructure of fibrous eutectics caused by convection: I .A fluctuating freezing rate, combined with unequal kinetics for fiber termination and branching. 2. Off-eutectic composition, either in the bulk melt due to an off-eutectic feed or at the freezing interface because of departure from the extremum condition. 3. Presence of a strong habit modifying impurity whose concentration at the freezing interface would be altered by convection. At the beginning of the present grant, we favored the first of these hypotheses and set out to test it both experimentally and theoretically. We planned the following approaches: I .Pass electric current pulses through the MnBi/Bi eutectic during directional solidification in order to produce an oscillatory freezing rate. 2. Directionally solidify the MnBi/Bi eutectic on Mir using the QUELD II gradient freeze furnace developed by Professor Smith at Queen's University. 3. Select another fibrous eutectic system for investigation using the Accelerated Crucible Rotation Technique to introduce convection. 4. Develop theoretical models for eutectic solidification with an oscillatory freezing rate. Because of the problems with Mir, we substituted ground-based experiments at Queen's University with QUELD II vertical and horizontal, with and without vibration of the furnace. The Al-Si system was chosen for the ACRT experiments. Three related approaches were used to model eutectic solidification with an oscillatory freezing rate. A sharp interface model was used to calculate composition oscillations at the freezing interface in response to imposed freezing rate oscillations.

Wilcox. William R.↗

Comparison of structures of gas atomized and of emulsified highly undercooled Ni-Sn alloy droplets

A comparison is made of microstructures of droplets of Ni-Sn alloys rapidly solidified by gas atomization and in a glass emulsifying medium. Cooling rate of the gas atomized particles ranged from 10 to the 3rd to 10 to the 6th K/s depending on droplet diameter (20-230 microns). In the hypoeutectic alloy studied, /Ni-(25 wt pct Sn)/, most particles showed a dendritic structure. These same particles, melted and resolidified in a glass medium using DTA (Differential Thermal Analysis), showed undercoolings up to 280 K: the structures were dendritic at low undercoolings and nondendritic at undercoolings above 220 K. It is concluded that the gas atomized particles exhibited little or no undercooling before nucleation; the solidification time of the undercooled emulsified droplets is substantially less than that of gas atomized droplets, and the undercooling required to achieve nondendritic structure depends on sample size.

Yamamoto, M.↗

Elevated-Temperature Deformation Properties of a HfC Modified Ti-48Al-2Mn-2Nb Matrix Particulate Composite

Rapid solidification techniques in combination with HIPing have been used to produce Ti-48Al-2Mn-2Nb and a Ti-48Al-2Mn-2Nb+15 wt% HfC composite. While the composite does contain several second phases within the gamma + alpha(sub 2) matrix, none was identified to be HfC. The elevated-temperature properties were determined by constant velocity compression and constant load tensile testing in air between 1000 and 1173 K. Such testing indicated that the elevated temperature strengths of the HfC-modified aluminide was superior to those of the unreinforced matrix with the best 1100 K temperature slow strain rate properties for both materials being achieved after high-temperature annealing prior to testing. Examination of the microstructures after deformation in combination with the measured stress exponents and activation energies suggest that creep resistance of the HfC-modified form is due to solid-solution strengthening from carbon and hafnium rather than the presence of second phases.

Whittenberger, J. D.↗

A Combined Computational, Experimental, and Technology Development Approach to In-Space Laser Manufacturing Maturation at NASA Marshall Space Flight Center

In-space manufacturing (ISM) is emerging as a field vital to continued access and capabilities in the space environment. NASA Marshall Space Flight Center (MSFC) is advancing the frontier of in-space laser manufacturing (ISLM) techniques through work initially focused on maturing laser beam welding (LBW) and laser forming (LF) for use in space. Such techniques proffer the ability to assemble and join structures in space from sheet metal or other stock – extant satellites, in situ resource utilization of Lunar regolith, etc. – by forming to desired shapes and then joining via in-space welding (ISW). ISLM processes are useful for assembly, joining, modification, and repair of structures in free space and on the Lunar surface such as large observatories, antennas, trusses, blast/thermal/radiation shields, pressure vessels, and more. However, these techniques are not yet qualified & certified (Q&C) for regular application in space. It would be prohibitively expensive, laborious, and time-consuming to perform Q&C via traditional experimental approaches as data collection & experimentation in space is resource-intensive. As such, benchmark experiments and focused, properly instrumented technology demonstration efforts in space can collect sufficient data that – when combined with verified computational models in an integrated computational materials engineering (ICME) approach – can validate ICME tools capable of translating more readily obtained ground data to in-space, in situ, computationally informed Q&C of ISLM techniques. Several ISLM projects at MSFC are obtaining the data required to validate ICME tools through both ground and flight experiments. A parabolic flight experiment of LBW under vacuum is manifested for August 2024, including both microgravity and Lunar gravity profiles. This collaboration with the Ohio State University is investigating common aerospace alloys such as 316L stainless steel, 2219 aluminum alloy, and Ti64 titanium alloy. In situ data collection includes videography, thermography, and reference thermocouples to build a thermal model of the welds. This will elucidate the relevant physics when combined with post-flight microstructural examination and mechanical testing. MSFC is also progressing towards a suborbital flight experiment of LBW under vacuum, which could provide reams of data on ISW during sustained, high-quality reduced gravity. The effect of combined thermal (cryogenic and high-temperature) and vacuum exposure on both LBW (NASA-funded) and LF (DARPA-funded) is being investigated through ground experiments. In addition to the copious data collected during these ground experiments, ruggedization of LBW hardware will also be pursued. The datasets from these experiments will be used to validate computational models which will inform future ISLM efforts in an ICME framework. A variety of techniques across lengths scales, from CALPHAD-driven thermodynamics & kinetics to phase field modeling of solidification to kinetic Monte Carlo simulations of grain evolution at the mesoscale, will be employed to accelerate the infusion and eventual Q&C of LBW and LF for use in space. The development of data-driven surrogate models to bridge ground to flight experiments and thereby reduce the need for resource-intensive experiments in space will also be investigated. These ICME techniques, surrogate models, and datasets from ground testing can also be employed to advance manufacturing in terrestrial environments.

in-space welding↗

Contribution to "AIAA Aerospace Year in Review" article

The NASA Marshall Space Flight Center Microgravity Science Program is dedicated to promoting our understanding of materials processing by conducting relevant experiments in the microgravity environment and supporting related modeling efforts with the intent of improving ground-based practices. Currently funded investigations include research on dopant distribution and defect formation in semiconductors, microstructural development and transitions in dendritic casting alloys, coarsening phenomena, competition between thermal and kinetic phase formation, and the formation of glassy vs. crystalline material. NASA Microgravity Materials Science Principle Investigators are selected for funding either through a proposal in response to a NASA Research Announcement or by collaborating on a team that has successfully proposed to a foreign space agency research announcement. In the latter case, a US investigator can then apply to NASA for funding through an unsolicited proposal. The International Space Station (ISS) facilities used for the experimental investigations are provided primarily by partnering with foreign agencies and often US investigators are working as a part of a larger team studying a specific area of materials science. Facilities for conducting experiments aboard the ISS include the European Space Agency (ESA) Low Gradient Facility (LGF) and the Solidification and Quench (SQF) modular inserts to the Materials Research Rack/Materials Science Laboratory and are primarily used for controlled solidification studies. The French Space Agency (CNES) provided DECLIC facility allows direct observation of morphological development in transparent materials that solidify analogously to metals. The ESA provided Electro ]Magnetic Levitator (EML) is designed to levitate, melt and then cool samples in order to determine material properties, study nucleation behavior, and document phase transitions. Finally, the Microgravity Science Glovebox (MSG) serves as a onboard facility for supporting the hardware required to conduct a number of smaller, short-term investigations.

Grugel, Richard N.↗

A study of the microstructure of a rapidly solidified nickel-base superalloy modified with boron

The microstructures of melt-spun superalloy ribbons with variable boron levels have been studied by transmission electron microscopy. The base alloy was of approximate composition Ni-11% Cr-5%Mo-5%Al-4%Ti with boron levels of 0.06, 0.12, and 0.60 percent (all by weight). Thirty micron thick ribbons display an equiaxed chill zone near the wheel contact side which develops into primary dendrite arms in the ribbon center. Secondary dendrite arms are observed near the ribbon free surface. In the higher boron bearing alloys, boride precipitates are observed along grain boundaries. A concerted effort has been made to elucidate true grain shapes by the use of bright field/dark field microscopy. In the low boron alloy, grain shapes are often convex, and grain faces are flat. Boundary faces frequently have large curvature, and grain shapes form concave polygons in the higher boron level alloys. It is proposed that just after solidification, in all of the alloys studied, grain shapes were initially concave and boundaries were wavy. Boundary straightening is presumed to occur on cooling in the low boron alloy. Boundary migration is precluded in the higher boron alloys by fast precipitation of borides at internal interfaces.

Speck, J. S.↗