Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SiC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Thermal diffusivity and thermal conductivity of SiC composite tubes: the effects of microstructure and irradiation

Cladding thermal conductivity is an important physical property in assessing the performance of silicon carbide (SiC)-cladded fuels for nuclear reactors. However, there is a significant lack of reliable data, particularly for irradiated materials, because the geometry complicates the measurement. This study investigates the thermal diffusivity of coupons with a curvature, machined from SiC fiber–reinforced SiC matrix composite tubes, with and without neutron irradiation under light water reactor–relevant temperature and dose conditions. The tested materials included full composite and duplex SiC composite tubes. The measurements were conducted using a modern flash diffusivity apparatus. The analyzed area on the specimen during diffusivity testing was reduced for improved measurement accuracy due to sample curvature. Post-irradiation measurements showed that the effects of neutron irradiation on thermal conductivity (e.g. thermal defect resistivity) are different between SiC composite plates versus tubes. The difference was explained by higher matrix density of the tube than the plate. This study provides reliable thermal properties of prototypic SiC composite tubes useful for fuel performance modeling of SiC-based cladding.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

X-ray tomography investigation of intensive sheared Al–SiC metal matrix composites

X-ray computed tomography (XCT) was used to characterise three dimensional internal structure of Al–SiC metal matrix composites. The alloy composite was prepared by casting method with the application of intensive shearing to uniformly disperse SiC particles in the matrix. Visualisation of SiC clusters as well as porosity distribution were evaluated and compared with non-shearing samples. Results showed that the average particle size as well as agglomerate size is smaller in sheared sample compared to conventional cast samples. Further, it was observed that the volume fraction of porosity was reduced by 50% compared to conventional casting, confirming that the intensive shearing helps in deagglomeration of particle clusters and decrease in porosity of Al–SiC metal matrix composites. - Highlights: • XCT was used to visualise 3D internal structure of Al-SiC MMC. • Al-SiC MMC was prepared by casting with the application of intensive shearing. • SiC particles and porosity distribution were evaluated. • Results show shearing deagglomerates particle clusters and reduces porosity in MMC.

36 MATERIALS SCIENCE↗

Growth of faceted SiC nanostructures using vapor phase condensation: Microstructural analysis

Highlights: • Synthesis of nanocrystalline SiC using thermal plasma route. • XRD data indicates presence of both α- and β-SiC polytypes with β-SiC as the major content. • HRTEM and SAED analysis reveals polytypic arrangement with stacking faults SiC nanoparticles. • TEM micrograph reveals presence of faceted structures such as hexagonal, triangular, triangular pyramidal structure. - Abstract: The paper emphasizes the morphological and microstructural analysis of SiC nanostructures grown by thermal plasma assisted gas phase condensation process. High Resolution Transmission Electron Microscopic and Selected Area Electron Diffraction studies are used to analyze the growth directions and the polytypic arrangement with stacking faults in the as synthesized SiC nanoparticles. The results help in understanding the hierarchical poly-types related to the observed geometries and showed the presence of both α- and β-SiC polytypes. The microstructural study is supported by X-Ray diffraction and UV–Visible absorption spectroscopic studies.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

One component metal sintering additive for {beta}-SiC based on thermodynamic calculation and experimental observations

Graphical abstract: . Standard Gibbs formation free energies vs. temperature for various metal carbides. The heavy line represents the standard Gibbs free energy for {beta}-SiC. The hatched area denotes the typical liquid phase hot pressing temperature of {beta}-SiC (1973-2123 K). Highlights: {yields} Various metal elements were examined as a sintering additive for {beta}-SiC. {yields} Al and Mg enhanced the density significantly without decomposing {beta}-SiC, as predicted by thermodynamic simulation. {yields} Cr, Fe, Ta, Ti, V and W additives formed metal carbide and/or silicide compounds by decomposing {beta}-SiC. {yields} This approach would be useful for selecting effective sintering additive for high temperature ceramics. -- Abstract: Various types of metals were examined as sintering additives for {beta}-SiC by considering the standard Gibbs formation free energy and vapor pressure under hot pressing conditions (1973-2123 K), particularly for applications in nuclear reactors. Metallic elements having the low long-term activation under neutron irradiation condition, such as Cr, Fe, Ta, Ti, V and W, as well as widely used elements, Al, Mg and B, were considered. The conclusions drawn from thermodynamic considerations were compared with the experimental observations. Al and Mg were found to be effective sintering additives, whereas the others were not due to the formation of metal carbides or silicides from the decomposition of SiC under hot pressing conditions.

36 MATERIALS SCIENCE↗

Investigation on gate oxide reliability under gate bias screening for commercial SiC planar and trench MOSFETs

This paper evaluates the impact of the fast high gate-voltage screening technique on gate oxide reliability of commercial 1.2 kV 4H-SiC power metal-oxide-semiconductor field-effect transistors (MOSFETs) with planar and trench gate structures. The measurements are conducted on packaged devices with the intent that the results will be applicable to wafer-level screening. The threshold voltage (V th ) of SiC MOSFETs is measured before and after various screening treatments and recovery process. In addition, constant-voltage time-dependent dielectric breakdown (TDDB) measurements are performed on SiC MOSFETs to obtain the intrinsic lifetime of gate oxide. The objective of this study is to determine the optimal screening conditions and improve screening efficiency without degradation of gate oxide reliability, such as V th shift and reduced oxide intrinsic lifetime. Due to the differences in the gate oxidation process and structural design of SiC planar and trench MOSFETs, the two types of devices exhibit different oxide reliability in the screening process. The recommended screening conditions obtained in this paper reveal that SiC trench MOSFETs can accept higher screening voltages compared to SiC planar MOSFETs. Hence, it can be concluded that more efficient screening techniques can be adopted for SiC MOSFETs with thicker gate oxide to meet the requirements of industrial applications.

36 MATERIALS SCIENCE↗

Irradiation-induced β to α SiC transformation at low temperature

Here, we observed that β-SiC, neutron irradiated to 9 dpa (displacements per atom) at ≈1440 °C, began transforming to α-SiC, with radiation-induced Frank dislocation loops serving as the apparent nucleation sites. 1440 °C is a far lower temperature than usual β → α phase transformations in SiC. SiC is considered for applications in advanced nuclear systems, as well as for electronic or spintronic applications requiring ion irradiation processing. β-SiC, preferred for nuclear applications, is metastable and undergoes a phase transformation at high temperatures (typically 2000 °C and above). Nuclear reactor concepts are not expected to reach the very high temperatures for thermal transformation. However, our results indicate incipient β → α phase transformation, in the form of small (~5–10 nm) pockets of α-SiC forming in the β matrix. In service transformation could degrade structural stability and fuel integrity for SiC-based materials operated in this regime. However, engineering this transformation deliberately using ion irradiation could enable new electronic applications.

36 MATERIALS SCIENCE↗

Effect of different thickness crystalline SiC buffer layers on the ordering of MgB{sub 2} films probed by extended x-ray absorption fine structure

Extended X-ray absorption fine structure (EXAFS) spectroscopy is a powerful method to investigate the local structure of thin films. Here, we have studied EXAFS of MgB{sub 2} films grown on SiC buffer layers. Crystalline SiC buffer layers with different thickness of 70, 100, and 130 nm were deposited on the Al{sub 2}O{sub 3} (0001) substrates by using a pulsed laser deposition method, and then MgB{sub 2} films were grown on the SiC buffer layer by using a hybrid physical-chemical vapor deposition technique. Transition temperature of MgB{sub 2} film decreased with increasing thickness of SiC buffer layer. However, the T{sub c} dropping went no farther than 100 nm-thick-SiC. This uncommon behavior of transition temperature is likely to be created from electron-phonon interaction in MgB{sub 2} films, which is believed to be related to the ordering of MgB{sub 2} atomic bonds, especially in the ordering of Mg–Mg bonds. Analysis from Mg K-edge EXAFS measurements showed interesting ordering behavior of MgB{sub 2} films. It is noticeable that the ordering of Mg–B bonds is found to decrease monotonically with the increase in SiC thickness of the MgB{sub 2} films, while the opposite happens with the ordering in Mg–Mg bonds. Based on these results, crystalline SiC buffer layers in MgB{sub 2} films seemingly have evident effects on the alteration of the local structure of the MgB{sub 2} film.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Photon absorption and emission properties of 7 Å SiC nanoclusters: Electronic gap, surface state, and quantum size effect

People know little experimentally about the physical properties of the SiC nanoclusters with sizes of a couple of angstroms. Herein, we study the electronic structure and light absorption/emission properties of the SiC nanoclusters with an average diameter of 7 Å that are fabricated by diminishing the sizes of the SiC microcrystals under high pressure and high temperature. The results reveal that the SiC nanoclusters have an indirect energy gap of 5.1 eV. Unlike the case of larger SiC nanocrystals, the luminescence of the SiC nanoclusters is dominated by two types of oxygen-related surface defects, and the maximum of their photoluminescence/photoluminescence excitation spectrum lies at 4.1/3.3 and 3.8/3.0 eV, respectively. The energy gap of the SiC nanoparticles with reference to bulk value is found to be inversely proportional to the diameter to the power 0.97, which shows slower increase of energy gap with decreasing size than what is predicted by using the first-principles calculations.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Edge states and ballistic transport in zigzag graphene ribbons: The role of SiC polytypes

Zigzag-edge graphene sidewall ribbons grown on 6 H -SiC {11¯2n} facet walls are ballistic conductors. Here, it is assumed that graphene sidewall ribbons grown on 4 H -SiC {11¯2n} facets would also be ballistic. In this work, we show that SiC polytype indeed matters: ballistic sidewall graphene ribbons only grow on 6 H -SiC facets. 4 H and 4 H -passivated sidewall graphene ribbons are diffusive conductors. Detailed photoemission and microscopy studies show that 6 H -SiC sidewall zigzag ribbons are metallic with a pair of n-doped edge states associated with asymmetric edge terminations. In contrast, 4 H -SiC zigzag ribbons are strongly bonded to the SiC, severely distorting the ribbon's π bands. H 2 passivation of the 4 H ribbons returns them to a metallic state but they show no evidence of edge states in their photoemission-derived band structure.

36 MATERIALS SCIENCE↗

Sizing SiC Storage Inverters for Fast Grid Frequency Support

As wind and solar displace synchronous generators whose inertia stabilizes the AC grid frequency on fast time scales, it has been proposed to use energy storage systems (ESSs) to mitigate frequency transient events. Such events require a rapid surge of power from the ESS, but they occur only rarely. The high temperature tolerance of SiC MOSFETs and diodes presents an opportunity for innovative ESS inverter designs. Herein we investigate a SiC ESS inverter design such that the SiC device ratings are obeyed during mild frequency events but are exceeded during rare, major events, for a potentially more economical inverter design. In support of this proposal we present: 1. An analysis of four years of grid frequency events in the U.S. Western Interconnection. 2. A switch-level ESS inverter simulation using SiC devices with detailed loss estimates. 3. Thermal analysis of the SiC power modules during a worst-case frequency event, showing that the modules can likely withstand the brief overcurrent. This analysis supports the conclusion that it may be advantageous for economical designs (acknowledging the increased risks) to undersize the SiC switches when designing inverters to perform active power control for grid frequency support. Such a strategy may result in SiC-based designs being more competitive with less costly silicon IGBT-based designs.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Electronic structure and the local electroneutrality level of SiC polytypes from quasiparticle calculations within the GW approximation

The most important interband transitions and the local charge neutrality level (CNL) in silicon carbide polytypes 3C-SiC and nH-SiC (n = 2-8) are calculated using the GW approximation for the self energy of quasiparticles. The calculated values of band gap E{sub g} for various polytypes fall in the range 2.38 eV (3C-SiC)-3.33 eV (2H-SiC) and are very close to the experimental data (2.42-3.33 eV). The quasiparticle corrections to E{sub g} determined by DFT-LDA calculations (about 1.1 eV) are almost independent of the crystal structure of a polytype. The positions of CNL in various polytypes are found to be almost the same, and the change in CNL correlates weakly with the change in E{sub g}, which increases with the hexagonality of SiC. The calculated value of CNL varies from 1.74 eV in polytype 3C-SiC to 1.81 eV in 4H-SiC.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

A Study of the Influence Exerted by Structural Defects on Photoluminescence Spectra in n-3C-SiC

Photoluminescence (PL) spectra have been studied in 3C-SiC/4H-SiC heterostructures and 3C‑SiC single crystals. It was shown that epitaxial 3C-SiC layers grown on 4H-SiC substrates have a markedly poorer crystal perfection than do 3C-SiC single crystals. It was found that doping with aluminum gives rise to a characteristic PL both in epitaxial layers and in 3C-SiC single crystals. At the same time, the electron irradiation of epitaxial layers does not give rise to defect-related PL, in contrast to what is observed for single crystals. An assumption is made that the twin boundaries existing in epitaxial 3C-SiC layers can serve as getters of radiation defects that are components of donor–acceptor pairs responsible for the “defect-related” PL.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Micromechanical Properties of the SiC and Pyrolytic Carbon Layers in Tristructural-Isotropic Coated Particles

Tristructural isotropic (TRISO) coated particle fuel was initially developed for high temperature gas cooled reactors (HTGR) and has been proposed for several other advanced reactor concepts. The design of TRISO particles focuses on preventing the release of fission products in normal and off-normal reactor conditions. The particle design features an actinide bearing fuel kernel that is surrounded by three pyrolytic carbon (PyC) layers and a silicon carbide layer (SiC). The mechanical stability of the particle and fission product retention for both metallic and gaseous fission products depend on the SiC layer. Post irradiation examination (PIE) of TRISO fuel from the first two US DOE Advanced Gas Reactor Fuel Development and Qualification Program irradiation campaigns, AGR-1 and AGR-2, had identified a low rate of particles exhibiting cracking in the SiC layer that did not propagate across the SiC layer. While cracking in the SiC is rare for test conditions and particles associated with the AGR program, understanding the stress state and mechanical properties of the SiC and PyC layers related to particle architecture can aid predicting thermomechanical response of TRISO fuel under the prescribed operation envelope and beyond as well as aiding in the development of similar fuel concepts for other advanced reactors. The presented investigation shows the relationship of the mechanical properties and mechanical response (e.g., understanding crack propagation) of the SiC and PyC layers relative to position within the particle. Testing was conducted on the inner and outer PyC layers of TRISO particles to quantify differences in mechanical behavior.

Montoya, Katherine [ORNL] (ORCID:0000000326955086)↗

Status of the Optical Dilatometer Method of Evaluating the Peak Irradiation Temperatures of SiC Passive Monitors

The main objective of this project was to conduct a comparative assessment between the optical dilatometer method and resistivity method, using all 10 SiC temperature monitors provided by two Nuclear Science User Facility experiments: BSU-8242 and General Electric Hitachi. Unfortunately, due to multiple delays in acquiring, shipping, and cleaning the SiC temperature monitors, the project was only able to process one (1) SiC temperature monitor during this period. SiC temperature monitor KGT-3357 was evaluated via the optical dilatometer method to determine its peak irradiation temperature. The KGT-3357 sample was from the BSU-8242 experiment and designed for a temperature of 300°C and an exposure of 1 dpa. The optical dilatometer measurements indicated that the KGT-3357 SiC temperature monitor’s peak irradiation temperature range was 240–267°C, with sensitivity of approximately ±20°C. Additionally, this temperature range falls within the evaluated melt wire temperature range of 238.6–271.5 °C. The remaining six (6) SiC temperature monitors from the BSU-8242 experiment and three (3) from the General Electric Hitachi experiment will be used in the future work to further validate the optical dilatometer method for measuring SiC peak irradiation temperatures.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A New Class of SiC Power MOSFETs with Record-Low Resistance

Silicon carbide (SiC) power transistors are used in the main traction inverter of electric vehicles (EVs). Tesla began installing SiC power MOSFETs in 2017, and has now produced 4.8 million EVs containing over 169 million SiC power MOSFETs. Looking ahead, the worldwide EV market is projected to exceed 50 million vehicles per year by 2030 (Reuters, Oct. 25, 2022). This will create a demand for over two billion SiC power MOSFETs per year. Our program aims to double the efficiency of today's commercial power MOSFETs. This will cut the number of MOSFETs per EV in half, reducing cost, simplifying assembly, decreasing weight, and increasing vehicle reliability through reduced parts count. Our approach is to apply innovative design and advanced processing to increase the density of current-controlling channels in SiC power MOSFET. We have developed two new MOSFET devices, each of which increases the channel density by a factor of six over today's best commercial MOSFETs. This required implementing new fabrication processes, creating new device designs, and integrating the processing steps and device designs into a manufacturable technology. In this project we have developed two innovative devices: (i) a novel three-dimensional structure, the "tri-gate MOSFET," and (ii) a deeply-scaled, fully self-aligned trench MOSFET, the "IMOSFET". Both products were experimentally demonstrated during this project and meet the program goals of increased efficiency relative to the current state-of-the art commercial products. In the process we have generated significant IP, with two US patents issued and three applications pending. We have also published three journal articles and given reports on this technology at seven international conferences. The success of this program has led to significant follow-on funding from industry. In May 2023 Purdue University signed a five-year R&D contract with GlobalFoundries to transfer our novel technology to commercial production. With headquarters in Malta, NY, Global Foundries is one of the largest pure-play silicon foundries in the world, with annual revenue of $\$$8.1B. Their SiC foundry will be built around the next-generation 200-mm diameter SiC wafers, which will double the number of die per wafer and reduce per-die production cost.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Breakdown Degradation Associated with Elementary Screw Dislocations in 4H-SiC P(+)N Junction Rectifiers

It is well-known that SiC wafer quality deficiencies are delaying the realization of outstandingly superior 4H-SiC power electronics. While efforts to date have centered on eradicating micropipes (i.e., hollow core super-screw dislocations with Burgers vector greater than 2c), 4H-SiC wafers and epilayers also contain elementary screw dislocations (i.e., Burgers vector = lc with no hollow core) in densities on the order of thousands per sq cm, nearly 100-fold micropipe densities. This paper describes an initial study into the impact of elementary screw dislocations on the reverse-bias current-voltage (I-V) characteristics of 4H-SiC p(+)n diodes. First, Synchrotron White Beam X-ray Topography (SWBXT) was employed to map the exact locations of elementary screw dislocations within small-area 4H-SiC p(+)n mesa diodes. Then the high-field reverse leakage and breakdown properties of these diodes were subsequently characterized on a probing station outfitted with a dark box and video camera. Most devices without screw dislocations exhibited excellent characteristics, with no detectable leakage current prior to breakdown, a sharp breakdown I-V knee, and no visible concentration of breakdown current. In contrast devices that contained at least one elementary screw dislocation exhibited a 5% to 35% reduction in breakdown voltage, a softer breakdown I-V knee, and visible microplasmas in which highly localized breakdown current was concentrated. The locations of observed breakdown microplasmas corresponded exactly to the locations of elementary screw dislocations identified by SWBXT mapping. While not as detrimental to SiC device performance as micropipes, the undesirable breakdown characteristics of elementary screw dislocations could nevertheless adversely affect the performance and reliability of 4H-SiC power devices.

Neudeck, P. G.↗

SiC JFET Transistor Circuit Model for Extreme Temperature Range

A technique for simulating extreme-temperature operation of integrated circuits that incorporate silicon carbide (SiC) junction field-effect transistors (JFETs) has been developed. The technique involves modification of NGSPICE, which is an open-source version of the popular Simulation Program with Integrated Circuit Emphasis (SPICE) general-purpose analog-integrated-circuit-simulating software. NGSPICE in its unmodified form is used for simulating and designing circuits made from silicon-based transistors that operate at or near room temperature. Two rapid modifications of NGSPICE source code enable SiC JFETs to be simulated to 500 C using the well-known Level 1 model for silicon metal oxide semiconductor field-effect transistors (MOSFETs). First, the default value of the MOSFET surface potential must be changed. In the unmodified source code, this parameter has a value of 0.6, which corresponds to slightly more than half the bandgap of silicon. In NGSPICE modified to simulate SiC JFETs, this parameter is changed to a value of 1.6, corresponding to slightly more than half the bandgap of SiC. The second modification consists of changing the temperature dependence of MOSFET transconductance and saturation parameters. The unmodified NGSPICE source code implements a T(sup -1.5) temperature dependence for these parameters. In order to mimic the temperature behavior of experimental SiC JFETs, a T(sup -1.3) temperature dependence must be implemented in the NGSPICE source code. Following these two simple modifications, the Level 1 MOSFET model of the NGSPICE circuit simulation program reasonably approximates the measured high-temperature behavior of experimental SiC JFETs properly operated with zero or reverse bias applied to the gate terminal. Modification of additional silicon parameters in the NGSPICE source code was not necessary to model experimental SiC JFET current-voltage performance across the entire temperature range from 25 to 500 C.

Neudeck, Philip G.↗

Fabrication and Characterization of Brazed Joints for SiC-Metallic Systems Utilizing Refractory Metals

Metal to ceramic joining plays a key role for the integration of ceramics into many nuclear, ground and aero based technologies. In order to facilitate these technologies, the active metal brazing of silicon carbide (CVD beta-SiC, 1.1 mm thick, and hot-pressed alpha-SiC, 3 mm thick) to the refractory metals molybdenum and tungsten using active braze alloys was studied. The joint microstructure, composition, and microhardness were evaluated by optical microscopy (OM), scanning electron microscopy (SEM), energy dispersive spectroscopy (EDS), and Knoop hardness testing. The braze alloys, Cusil-ABA, Ticusil and Copper-ABA, all formed sound joints with excellent wetting and chemical bonding with the SiC substrate. Despite the close thermal expansion match between the metal substrates and SiC, hairline cracks formed in alpha-SiC while beta-SiC showed no signs of residual stress cracking. The use of ductile interlayers to reduce the effect from residual stresses was investigated and joints formed with copper as an interlayer produced crack free systems utilizing both CVD and hot-pressed SiC.

Coddington, Bryan↗