Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SOOT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Optical measurements of soot in premixed flames

Two laser diagnostic techniques were used to measure soot volume fractions, number densities and soot particle radii in premixed propane/oxygen flat flames. The two techniques were two wavelength extinction, using 514.5 to 632.8 nm and 457.9 to 632.8 nm wavelength combinations, and extinction/scattering using 514.5 nm light. The flames were fuel rich and had cold gas velocities varying from 3.4 to 5.5 cm/s. Measurements were made at various heights above the sintered bronze, water colored flat flame burner with the equivalence ratio and cold gas velocity fixed. Also, measurements were made at a fixed height above the burner and fixed cold gas velocity while varying the equivalence ratio. Both laser techniques are based on the same underlying assumptions of particle size distribution and soot optical properties. Full Mie theory was used to determine the extinction coefficients and the scattering efficiencies. Temperature measurements in the flame were made using infrared radiometry and fine wire thermocouples. Good agreement between the two techniques in terms of soot particle radii, number density and volume fraction was found for intensity ratios between 0.1 and 0.8.

Lyons, Valerie J.↗

Diamonds in detonation soot

Diamonds 4 to 7 nm in diameter have been identified and partially isolated from soot formed in detonations of carbon-forming composite explosives. The morphology of the soot has been examined by transmission electron microscopy (TEM), and the identity of the diamond has been established by the electron diffraction pattern of the TEM samples and by the X-ray diffraction (XRD) pattern of the isolated solid. Graphite is also present in the form of ribbons of turbostatic structure with a thickness of 2 to 4 nm. A fraction, about 25 percent of the soot by weight, was recovered from the crude soot after oxidation of the graphite with fuming perchloric acid. This fraction showed a distinct XRD pattern of diamond and the diffuse band of amorphous carbon. The IR spectrum of these diamonds closely matches that of diamonds recovered from meteorites (Lewis et al., 1987), perhaps indicating similar surface properties after the oxidation. If these diamonds are produced in the detonation itself or during the initial expansion, they exhibit a phenomenal crystal growth rate (5 nm/0.00001 s equal 1.8 m/hr) in a medium with a very low hydrogen/carbon ratio. Because the diamonds will be carried along with the expanding gases, they will be accelerated to velocities approaching 8 km/s.

Greiner, N. Roy↗

Soot formation in shock-tube pyrolysis and oxidation of vinylacetylene

Soot formation in vinylacetylene, and vinylacetylene-oxygen argon-diluted mixtures was studied behind reflected shock waves by monitoring the attenuation of a 632.8-nm He-Ne laser beam. The experiments were performed at temperatures of 1600-2500 K, pressures of 2.08-3.09 bar, and total carbon atom concentrations of (1.99-2.05) x 10 to the 17th atoms/cu cm. The experimental results obtained in pyrolysis of vinylacetylene are similar to those of acetylene, both in the order of magnitude of the soot yield and the shape of its temperature dependence. The addition of oxygen to vinylacetylene shifts the soot bell to lower temperature and, distinct from all other hydrocarbons studied in this laboratory, accelerates the production of soot with reaction time. The experimental results are interpreted in terms of possible chemical reaction.

Frenklach, M.↗

Structure of Soot-Containing Laminar Jet Diffusion Flames

The structure and soot properties of nonbuoyant and weakly-buoyant round jet diffusion flames were studied, considering ethylene, propane and acetylene burning in air at pressures of 0.125-2.0 atm. Measurements of flame structure included radiative heat loss fractions, flame shape and temperature distributions in the fuel-lean (overfire) region. These measurements were used to evaluate flame structure predictions based on the conserved-scalar formalism in conjunction with the laminar flamelet concept, finding good agreement betweem predictions and measurements. Soot property measurements included laminar smoke points, soot volume function distributions using laser extinction, and soot structure using thermophoretic sampling and analysis by transmission electron microscopy. Nonbuoyant flames were found to exhibit laminar smoke points like buoyant flames but their properties are very different; in particular, nonbuoyant flames have laminar smoke point flame lengths and residence times that are shorter and longer, respectively, than buoyant flames.

Mortazavi, S.↗

Laser-saturated fluorescence measurements in laminar sooting diffusion flames

The hydroxyl radical is known to be one of the most important intermediate species in the combustion processes. The hydroxyl radical has also been considered a dominant oxidizer of soot particles in flames. In this investigation the hydroxyl concentration profiles in sooting diffusion flames were measured by the laser-saturated fluorescence (LSF) method. The temperature distributions in the flames were measured by the two-line LSF technique and by thermocouple. In the sooting region the OH fluorescence was too weak to make accurate temperature measurements. The hydroxyl fluorescence profiles for all four flames presented herein show that the OH fluorescence intensities peaked near the flame front. The OH fluorescence intensity dropped sharply toward the dark region of the flame and continued declining to the sooting region. The OH fluorescence profiles also indicate that the OH fluorescence decreased with increasing height in the flames for all flames investigated. Varying the oxidizer composition resulted in a corresponding variation in the maximum OH concentration and the flame temperature. Furthermore, it appears that the maximum OH concentration for each flame increased with increasing flame temperature.

Wey, Changlie↗

Soot Precursor Material: Spatial Location via Simultaneous LIF-LII Imaging and Characterization via TEM

The chemical and physical transformation between gaseous fuel pyrolysis products and solid carbonaceous soot represents a critical step in soot formation. In this paper, simultaneous two-dimensional LIF-LII (laser-induced fluorescence - laser-induced incandescence) images identify the spatial location where the earliest identifiable chemical and physical transformation of material towards solid carbonaceous soot occurs along the axial streamline in a normal diffusion flame. The identification of the individual LIF and LII signals is achieved by examining both the excitation wavelength dependence and characteristic temporal decay of each signal. Spatially precise thermophoretic sampling measurements are guided by the LIF-LII images with characterization of the sampled material accomplished via both bright and dark field TEM. Both bright and dark field TEM measurements support the observed changes in photophysical properties which account for conversion of fluorescence to incandescence as fuel pyrolysis products evolve towards solid carbonaceous soot.

VanderWal, Randall L.↗

Laminar Soot Processes

Soot processes within hydrocarbon-fueled flames affect particle emissions from combustion processes, thermal loads of combustor components, hazards of unwanted fires, and capabilities for computational combustion. Thus, soot processes within laminar nonpremixed (diffusion) and premixed flames are being studied, using both space-based (flight) experiments at MicroGravity (MG) and supporting ground-based experiments at Normal Gravity (NG). The study is limited to laminar flames due to their experimental and computational tractability, noting the relevance of these results to practical turbulent flames based on laminar flamelet concepts. Unfortunately, buoyancy affects soot processes in laminar diffusion flames while effects of buoyancy are small for most practical flames; therefore, present observations of laminar diffusion flames involve either particular flame conditions where effects of buoyancy are small during ground-based experiments at ng or truly nonbuoyant flames during planned flight experiments at mg. Laminar premixed flames are also being considered during ground-based experiments at ng because soot processes are easier to interpret and less affected by buoyancy in laminar premixed flames than in laminar diffusion flames.

Xu, F.↗

Brief Communication: Buoyancy-Induced Differences in Soot Morphology

Reduction or elimination of buoyancy in flames affects the dominant mechanisms driving heat transfer, burning rates and flame shape. The absence of buoyancy produces longer residence times for soot formation, clustering and oxidation. In addition, soot pathlines are strongly affected in microgravity. We recently conducted the first experiments comparing soot morphology in normal and reduced-gravity laminar gas jet diffusion flames. Thermophoretic sampling is a relatively new but well-established technique for studying the morphology of soot primaries and aggregates. Although there have been some questions about biasing that may be induced due to sampling, recent analysis by Rosner et al. showed that the sample is not biased when the system under study is operating in the continuum limit. Furthermore, even if the sampling is preferentially biased to larger aggregates, the size-invariant premise of fractal analysis should produce a correct fractal dimension.

Ku, Jerry C.↗

Quantitative Surface Emissivity and Temperature Measurements of a Burning Solid Fuel Accompanied by Soot Formation

Surface radiometry is an established technique for noncontact temperature measurement of solids. We adapt this technique to the study of solid surface combustion where the solid fuel undergoes physical and chemical changes as pyrolysis proceeds, and additionally may produce soot. The physical and chemical changes alter the fuel surface emissivity, and soot contributes to the infrared signature in the same spectral band as the signal of interest. We have developed a measurement that isolates the fuel's surface emissions in the presence of soot, and determine the surface emissivity as a function of temperature. A commercially available infrared camera images the two-dimensional surface of ashless filter paper burning in concurrent flow. The camera is sensitive in the 2 to 5 gm band, but spectrally filtered to reduce the interference from hot gas phase combustion products. Results show a strong functional dependence of emissivity on temperature, attributed to the combined effects of thermal and oxidative processes. Using the measured emissivity, radiance measurements from several burning samples were corrected for the presence of soot and for changes in emissivity, to yield quantitative surface temperature measurements. Ultimately the results will be used to develop a full-field, non-contact temperature measurement that will be used in spacebased combustion investigations.

Piltch, Nancy D.↗

Flame and Soot Boundaries of Laminar Jet Diffusion Flames

The shapes (flame-sheet and luminous-flame boundaries) or steady weakly buoyant round hydrocarbon-fueled laminar-jet diffusion flames in still and coflowing air were studied both experimentally and theoretically. Flame-sheet shapes were measured from photographs using a CH optical filter to distinguish flame-sheet boundaries in the presence of blue CO2 and OH emissions and yellow continuum radiation from soot. Present experimental conditions included acetylene-, methane-, propane-, and ethylene-fueled flames having initial reactant temperatures of 300 K. ambient pressures of 4-50 kPa, jet-exit Reynolds numbers of 3-54, initial air/fuel velocity ratios of 0-9, and luminous flame lengths of 5-55 mm; earlier measurements for propylene- and 1,3-butadiene-fueled flames for similar conditions were considered as well. Nonbuoyant flames in still air were observed at microgravity conditions; essentially nonbuoyant flames in coflowing air were observed at small pressures to control effects of buoyancy. Predictions of luminous flame boundaries from soot luminosity were limited to laminar smoke-point conditions, whereas predictions of flame-sheet boundaries ranged from soot-free to smoke-point conditions. Flame-shape predictions were based on simplified analyses using the boundary-layer approximations along with empirical parameters to distinguish flame-sheet and luminous-flame (at the laminar smoke point) boundaries. The comparison between measurements and predictions was remarkably good and showed that both flame-sheet and luminous-flame lengths are primarily controlled by fuel flow rates with lengths in coflowing air approaching 2/3 of the lengths in still air as coflowing air velocities are increased. Finally, luminous flame lengths at laminar smoke-point conditions were roughly twice as long as flame-sheet lengths at comparable conditions because of the presence of luminous soot particles in the fuel-lean region of the flames.

Xu, F.↗

Laminar Soot Processes (Lsp) Experiment: Findings From Ground-Based Measurements

Processes of soot formation and oxidation must be understood in order to achieve reliable computational combustion calculations for nonpremixed (diffusion) flames involving hydrocarbon fuels. Motivated by this observation, the present investigation extended earlier work on soot formation and oxidation in laminar jet ethylene/air and methane/oxygen premixed and acetylene-nitrogen/air diffusion flames at atmospheric pressure in this laboratory, emphasizing soot surface growth and early soot surface oxidation in laminar diffusion flames fueled with a variety of hydrocarbons at pressures in the range 0.1 - 1.0 atm.

Kim, C. H.↗

A Computational Investigation of Sooting Limits of Spherical Diffusion Flames

Limiting conditions for soot particle inception in spherical diffusion flames were investigated numerically. The flames were modeled using a one-dimensional, time accurate diffusion flame code with detailed chemistry and transport and an optically thick radiation model. Seventeen normal and inverse flames were considered, covering a wide range of stoichiometric mixture fraction, adiabatic flame temperature, and residence time. These flames were previously observed to reach their sooting limits after 2 s of microgravity. Sooting-limit diffusion flames with residence times longer than 200 ms were found to have temperatures near 1190 K where C/O = 0.6, whereas flames with shorter residence times required increased temperatures. Acetylene was found to be a reasonable surrogate for soot precursor species in these flames, having peak mole fractions of about 0.01.

Lecoustre, V. R.↗

CFD Predictions of Soot & CO Emissions Generated by a Partially-Fueled 9-Element Lean-Direct Injection Combustor

A study was undertaken to investigate the CO & soot emissions generated by a partially-fueled 9- element LDI (Lean-Direct Injection) combustor configuration operating in the idle range of jet engine conditions. In order to perform the CFD analysis, several existing soot/chemistry models were implemented into the OpenNCC (Open National Combustion Code). The calculations were based on a Reynolds-Averaged Navier Stokes (RANS) simulation with standard k-epsilon turbulence model, a 62- species jet-a/air chemistry, a 2-equation soot model, & a Lagrangian spray solver. A separate transport equation was solved for all individual species involved in jet-a/air combustion. In the test LDI configuration we examined, only five of the nine injectors were fueled with the major pilot injector operating at an equivalence ratio of near one and the other four main injectors operating at an equivalence ratio near 0.55. The calculations helped to identify several reasons behind the soot & CO formation in different regions of the combustor. The predicted results were compared with the reported experimental data on soot mass concentration (SMC) & emissions index of CO (EICO). The experimental results showed that an increase in either T3 and/or F/A ratio lead to a reduction in both EICO & SMC. The predicted results were found to be in reasonable agreement. However, the predicted EICO differed substantially in one test condition associated with higher F/A ratio.

Raju, M. S.↗

Method for removing soot from exhaust gases

A method for oxidizing soot from diesel exhaust gas from a diesel engine. The method involves providing a diesel particulate filter for receiving the diesel exhaust gas; coating a catalyst composition on the diesel particulate filter; and contacting the soot from the diesel exhaust gas with the catalyst coated diesel particulate filter at a temperature sufficient to oxidize the soot to carbon dioxide. The catalyst composition is a doped or undoped manganese oxide octahedral molecular sieve (OMS-2) material. A diesel exhaust gas treatment system that includes a diesel particulate filter for receiving diesel exhaust gas from a diesel engine and collecting soot; and a catalyst composition coated on the diesel particulate filter. The catalyst composition is a doped or undoped manganese oxide octahedral molecular sieve (OMS-2).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A numerical study on the sooting tendencies of bio-derived fuels for spark-ignition engines

While more efficient vehicles have been developed over the decades, their performance is limited by the properties of existing fuels. In response, the Co-Optimization of Fuels and Engines Initiative (Co-Optima) under the U.S. Department of Energy (DOE) has developed a rigorous screening approach to identify the most promising biomass-derived blendstocks that are suitable for advanced spark-ignition (SI) engines. A detailed kinetic model has also been developed to predict the combustion properties of the selected blendstocks. This kinetic model has been designed mainly targeting ignition and flame propagation properties, and it has not previously been validated for soot formation. In this work, we numerically predicted the sooting tendency of 20 Co-Optima SI blendstocks using the Co-Optima kinetic model. The sooting tendencies are determined quantitatively using the Yield Sooting Index (YSI) methodology. As shown in Fig. 1, the predicted YSIs show good agreement with measurements, except for 2,5-dimethylfuran. We also quantify the sensitivity of the YSI predictions to aromatic growth reactions and fuel decomposition reactions of the test fuels. It is found that PAH growth reactions have little impact on YSIs for all 20 fuels under investigation. On the other hand, fuel decomposition reactions have a significant influence on the YSI of 2,5-dimethylfuran. Perturbing their reaction rates by a factor of two is shown to lead to 11 % YSI prediction uncertainty.

09 BIOMASS FUELS↗

Experimental and theoretical study of the soot-forming tendencies of furans as potential biofuels

Sustainably-produced biofuels, including furans derived from lignocellulosic biomass, are being studied as potential next-generation fuels. Biofuels have unique structures that are absent in conventional fuels and they potentially emit fewer particulates than conventional fuels because of the presence of oxygen atoms. In this work, we focus on quantification and measurement of sooting tendency. A set of furans was selected and their sooting tendencies were characterized by Yield Sooting Index (YSI), which was obtained by measuring the line-of-sight spectral radiance (LSSR) of a coflow laminar diffusion flame doped with 1000 ppm of each test fuel. The measured YSIs are lower than traditional gasoline fuels and benzenoid aromatics (e.g., YSIbenzene = 100). We also performed numerical simulations with a detailed chemical kinetic mechanism to analyze the flame chemistry of 2-methylfuran (2MF). 4→5 H-atom migration in the furan ring causes 31.0% of the total decomposition and is the dominant fuel consumption pathway leading to soot. DFT calculations via the G4 composite method were carried out to obtain activation energies (Ea) and bond dissociation energies (BDE). The results showed that the 4→5 H-atom migration in the furan ring has the second lowest Ea and subsequently forms a 1,2-diene-substituted ketone derivative as a stable species. The ring-opening products of the 4→5 H-atom migration are propyne + a linear ketene for 2-n-alkylfurans, and 1-butyne + a methyl-substituted ketene for 2-t-butylfuran. These results can explain the trends of the measured YSIs of 2-alkylfurans.

09 BIOMASS FUELS↗

Reconstruction of soot temperature and volume fraction profiles of an asymmetric flame using stereoscopic tomography

The present study attempts to reconstruct soot temperature and volume fraction distributions for the asymmetric diffusive flame using a tomography technique. A high-resolution camera equipped with a stereo adapter was employed to capture stereoscopic flame images, which were used to obtain monochromatic line-of-sight flame emission projections within the visible range. A matrix-decomposition-based least squares algorithm was introduced to reconstruct the emission intensity distributions in the flame sections. The retrieved intensities were used to infer local soot temperature and volume fraction. Numerical assessments show that for soot volume fraction measurement, the system signal-to-noise ratio should be larger than 62.5 dB. The proposed tomography system was found to be capable of symmetric and asymmetric flame measurements. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of Kinetics for Soot Oxidation at High Pressures Under Fuel-Lean Conditions

The focus of the proposed research was to develop kinetic models for soot oxidation with the hope of developing a validated, predictive, multi-­scale, combustion model to optimize the design and operation of evolving fuels in advanced engines for transportation applications. The work focused on the relatively unstudied area of the fundamental mechanism for soot oxidation. The objectives include understanding of the kinetics of soot oxidation by O2 under high pressure which require: 1) development of intrinsic kinetics for the surface oxidation, which takes into account the dependence of reactivity upon nanostructure and 2) evolution of nanostructure and its impact upon oxidation rate and 3) inclusion of internal surface area development and possible fragmentation resulting from pore development and /or surface oxidation. These objectives were explored for a variety of pure fuel components and surrogate fuels. This project was a joint effort between the University of Utah (UU) and Pennsylvania State University (Penn State). The work at the UU focuses on experimental studies using a two-­stage burner and a high- pressure thermogravimetric analyzer (TGA). Penn State provided HRTEM images and guidance in the fringe analysis algorithms and parameter quantification for the images. This report focuses on completion done under supplemental funding.

02 PETROLEUM↗