Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ROCK MECHANICS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Lunar surface engineering properties experiment definition

Research on the mechanics of lunar soils and on developing probes to determine the properties of lunar surface materials is summarized. The areas of investigation include the following: soil simulation, soil property determination using an impact penetrometer, soil stabilization using urethane foam or phenolic resin, effects of rolling boulders down lunar slopes, design of borehole jack and its use in determining failure mechanisms and properties of rocks, and development of a permeability probe for measuring fluid flow through porous lunar surface materials.

Mitchell, J. K.↗

Laboratory measurements of p-wave seismic Q on lunar and analog rocks

The longitudinal-wave, internal friction quality factor (Qp) of out-gassed rock subjected to hydrostatic confining pressure was measured by a technique of aerodynamically shaping the sample ends to remove most of the air drag. Q values of about 1000 and 100 were obtained at 100 MPa and in laboratory air, respectively. The temperature dependence of Q in lunar rock 70215.85 and an analog of lunar basalt was investigated over the range -100 to 450 deg C. A systematic increase in Q was observed at 50 Hz, 5 kHz and 50 kHz. When the temperature was lowered to -100 deg C moderate decreases in Q were observed from 100 to 250 deg C, and high Q values were obtained at 450 deg C. The temperature and pressure dependences of Q suggest that high lunar seismic Q values imply a very dry crust to depths of at least 50 km. These results further indicate that elastic waves are damped in volatile-rich rock by an absorption mechanism which involves changes in the bonding, structure and coverage of the molecular, physisorbed and chemisorbed H2O at crack and grain boundaries.

Tittmann, B. R.↗

On the relationship between age of lava flows and radar backscattering

The observation that older lava flows have lower backscatter in radar images is assessed with multiwavelength/polarization scatterometer data with incidence angles from 15 to 50 deg. Backscatter decreases over time because surface roughness decreases due to infilling with dust and mechanical weathering of the rocks. Pahoehoe lavas in the Snake River Plain with ages of 2.1, 7,4, and 12.0 K yr are best separated with 2.25 cm wavelength data. Blocky obsidian flows at Medicine Lake Highland and Newberry Volcano with ages of 0.9, 1.1 and 1.4 K yr are best separated with 6.3 cm wavelength data. Two Pleistocene flows at the Snake River Plain are best separated with 19.0 cm wavelength data. Incidence angles from 20 to 35 deg are best. These data indicate it may be possible to separate lava flows into eruptive periods using calibrated multiwavelength radar backscatter data.

Blom, R. G.↗

Biogeochemical Activity of Siderophilic Cyanobacteria and Insights from their Genomes Implications for the Development of New Biosignatures

Verifying the links between genomie features in living organisms and their mineralization/demineralization activity will help to reveal traces of life on Earth and beyond. Among contemporary environments, iron-depositing hot springs (IDHS) may represent one of the most appropriate natural models for insights into ancient life since organisms may have originated on Earth and possibly Mars in association with hydrothennal activity and high [Fe(2+)]. Siderophilic or "iron-loving" cyanobacteria (CB) inhabiting IDHS may have genomic features and properties similar to those of ancient organisms because abundant Fe(2+) in IDHS has a strong potential to increase the magnitude of oxidative stress. That is why specific and/or additional proteins involved in Fe mineralization by siderophilic CB are expected. Inorganic polyphosphates (PPi) are known to increase the viability of prokaryotes Linder heavy metal concentrations and UV stress conditions. PPi have also been proposed as biosignatures. Ancient CB could have also been stressed by occasional migrations from the Fe(2+) rich Ocean to the basaltic land which was almost devoid of dissolved Fe(2+). Thus, the study of the adaptation reactions of siderophilic CB to fluctuation of dissolved Fe level may shed light on the paleophysiology of ancient oxygenic prokaryotes. Moreover, bioweathered Fe, Al, P, Cu, Ti and rare earth elements can be thought of as candidate organomarkers that document the effects of or ganic molecules in weathered rocks. However, the molecular mechanisms of the maintenance of Fe homeostasis in siderophilic CB, the role of PPi for this process and bioweathering activities are poorly understood. Here we present preliminary results describing a new mechanism of Fe mineralization in siderophilic CB, the effect of Fe on the generation of PPi bodies in siderophilic CB, their bioweathering activity and preliminary analysis of the diversity of proteins involved in the prevention of oxidative stress in phototrophs inhabiting IDHS.

Brown, I. I.↗

On the Recovery Stress of a Ni50.3Ti29.7Hf20 High Temperature Shape Memory Alloy

Recovery stress in shape memory alloys (SMAs), also known as blocking stress, is an important property generally obtained during heating under a dimensional constraint as the material undergoes the martensitic phase transformation. This property has been instinctively utilized in most SMA shape-setting procedures, and has been used in numerous applications such as fastening and joining, rock splitting, safety release mechanisms, reinforced composites, medical devices, and many other applications. The stress generation is also relevant to actuator applications where jamming loads (e.g., in case the actuator gets stuck and is impeded from moving) need to be determined for proper hardware sizing. Recovery stresses in many SMA systems have been shown to reach stresses in the order of 800 MPa, achieved via thermo-mechanical training such as pre-straining, heat treatments or other factors. With the advent of high strength, high temperature SMAs, recovery stress data has been rarely probed, and there is no information pertinent to the magnitudes of these stresses. Thus, the purpose of this work is to investigate the recovery stress capability of a precipitation strengthened, Ni50.3Ti29.7Hf20 (at.) high temperature SMA in uniaxial tension and compression. This material has been shown to exhibit outstanding strength and stability during constant-stress, thermal cycling, but no data exists on constant-strain thermal cycling. Several training routines were implemented as part of this work including isothermal pre-straining, isobaric thermal cycling, and isothermal cyclic training routines. Regardless of the training method used, the recovery stress was characterized using constant-strain (strain-controlled condition) thermal cycling between the upper and lower cycle temperatures. Preliminary results indicate recovery stresses in excess of 1.5 GPa were obtained after a specific training routine. This stress magnitude is significantly higher than conventional NiTi stress generation capability.

Recovery Stress↗

In Situ Radiometric and Exposure Age Dating of the Martian Surface

We determined radiogenic and cosmogenic noble gases in a mudstone on the floor of Gale Crater. A K-Ar age of 4.21 +/- 0.35 billion years represents a mixture of detrital and authigenic components and confirms the expected antiquity of rocks comprising the crater rim. Cosmic-ray-produced 3He, 21Ne, and 36Ar yield concordant surface exposure ages of 78 T 30 million years. Surface exposure occurred mainly in the present geomorphic setting rather than during primary erosion and transport. Our observations are consistent with mudstone deposition shortly after the Gale impact or possibly in a later event of rapid erosion and deposition. The mudstone remained buried until recent exposure by wind-driven scarp retreat. Sedimentary rocks exposed by this mechanism may thus offer the best potential for organic biomarker preservation against destruction by cosmic radiation.

age dating↗

Impact of Brine/CO 2 exposure on the transport and mechanical properties of the Mt Simon sandstone

When sandstone rocks are exposed to CO 2 -saturated brine, their transport and mechanical properties can change due to brine/CO 2 -induced chemical reactions. The present study investigates the change in the flow-through characteristics, porosity, and the mechanical behavior of Mt. Simon Sandstone samples caused by exposure to brine/CO 2 . The cores, extracted from a depth interval of 2110.4–2111.4 m (6924–6927 ft) in the Mt. Simon formation, were first characterized for their mechanical and transport properties, and then aged in CO 2 -saturated brine at pressures of 17.24 MPa (2500 psi) and temperature of 50°C for one to two weeks. Following that, the changes in the transport and mechanical properties of the samples were analyzed using He pycnometry, flow perporometry and triaxial testing. Our experiments show that the porosity of the Mt. Simon samples slightly increases after exposure to CO 2 /brine, while the permeability increases more substantially depending on the stress state. Measurements of the flow-through pore size distribution (PSD) are indicative of the changes occurring and are consistent with the observed increases in permeability. Nitrogen adsorption tests (BET), before and after incubation, show a significant loss of pore volume in the mesoporous range that is indicative of clay dissolution. Weakening of the materials was observed based on the mechanical properties studied, a result that is consistent with the observed dissolution of clays that play a central role in the cementation of the quartz grains. Finally, the analysis of the brine compositions reveals an increase in concentration of most cations after incubation with the Mt. Simon cores. This is also consistent with mineral/clay dissolution, confirmed by the porosity, transport, and mechanical property measurements as well as electron microscopy analysis of the same samples.

58 GEOSCIENCES↗

Results from the US-German Benchmark Initiative for FY14

Sandia recently joined the third phase of and is a contributing partner to a U.S.-German “Joint Project” entitled “Comparison of current constitutive models and simulation procedures on the basis of model calculations of the thermo-mechanical behavior and healing of rock salt.” The first goal of the project is to check the ability of numerical modeling tools to correctly describe the relevant deformation phenomena in rock salt under various influences. Achieving this goal will lead to increased confidence in the results of numerical simulations related to the secure storage of radioactive wastes in rock salt, thereby enhancing the acceptance of the results. These results may ultimately be used to make various assertions regarding both the stability analysis of an underground repository in salt during the operating phase and the long-term integrity of the geological barrier against the release of harmful substances into the biosphere in the post-operating phase. Among the numerical modeling tools are constitutive models that are used in computer simulations for the description of the thermal, mechanical, and hydraulic behavior of the host rock under various influences and for the long-term prediction of this behavior into the future. A second goal of the project is to investigate and demonstrate the possibilities for further potential development and improvement of these constitutive models. This report summarizes the efforts undertaken during FY14 in support of these international benchmark calculations of field experiments.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Summary of FY15 Results of Benchmark Modeling Activities

Sandia is participating in the third phase of and is a contributing partner to a U.S.- German “Joint Project” entitled “Comparison of current constitutive models and simulation procedures on the basis of model calculations of the thermo-mechanical behavior and healing of rock salt.” The first goal of the project is to check the ability of numerical modeling tools to correctly describe the relevant deformation phenomena in rock salt under various influences. Achieving this goal will lead to increased confidence in the results of numerical simulations related to the secure storage of radioactive wastes in rock salt, thereby enhancing the acceptance of the results. These results may ultimately be used to make various assertions regarding both the stability analysis of an underground repository in salt, during the operating phase, and the long-term integrity of the geological barrier against the release of harmful substances into the biosphere, in the post-operating phase. Among the numerical modeling tools required to address this are constitutive models that are used in computer simulations for the description of the thermal, mechanical, and hydraulic behavior of the host rock under various influences and for the long-term prediction of this behavior into the future. A second goal of the project is to investigate and demonstrate the possibilities for further potential development and improvement of these constitutive models. This report summarizes the efforts undertaken during FY15 in support of this international U.S.-German benchmark initiative.

58 GEOSCIENCES↗

Predicting the Sources and Formation Mechanisms of Evolved Lunar Crust by Linking K/Ca Ratios of Lunar Granites to Analogous Terrestrial Igneous Rocks

Although silicic rocks (i.e. granites and rhyolites) comprise a minor component of the sampled portion of the lunar crust, recent remote sensing studies [e.g., 1-4] indicate that several un-sampled regions of the Moon have significantly higher concentrations of silicic material (also high in [K], [U], and [Th]) than sampled regions. Within these areas are morphological features that are best explained by the existence of chemically evolved volcanic rocks. Observations of silicic domes [e.g., 1-5] suggest that sizable networks of silicic melt were present during crust formation. Isotopic data indicate that silicic melts were generated over a prolonged timespan from 4.3 to 3.9 Ga [e.g., 6-8]. The protracted age range and broad distribution of silicic rocks on the Moon indicate that their petrogenesis was an important mechanism for secondary crust formation. Understanding the origin and evolution of such silicic magmas is critical to determining the composition of the lunar crustal highlands and will help to distinguish between opposing ideas for the Moon's bulk composition and differentiation. The two main hypotheses for generating silicic melts on Earth are fractional crystallization or partial melting. On the Moon silicic melts are thought to have been generated during extreme fractional crystallization involving end-stage silicate liquid immiscibility (SLI) [e.g. 9, 10]. However, SLI cannot account for the production of significant volumes of silicic melt and its wide distribution, as reported by the remote global surveys [1, 2, 3]. In addition, experimental and natural products of SLI show that U and Th, which are abundant in the lunar granites and seen in the remote sensing data of the domes, are preferentially partitioned into the depolymerized ferrobasaltic magma and not the silicic portion [11, 12]. If SLI is not the mechanism that generated silicic magmas on the Moon then alternative processes such as fractional crystallization (only crystal-liquid separation) or partial melting should be considered as viable possibilities to be tested.

Mills, R. D.↗

Benchmark study of a new simplified DFN model for shearing of intersecting fractures and faults

It is challenging to quantitatively predict shearing of intersecting fractures/faults because of dynamic frictional contacts accompanied by possible nonlinear rock deformation. To address such challenges, a new conceptual model—the simplified DFN model—was proposed and validated by Hu et al. 46 to use major paths (MPs) to represent complicated DFNs for calculation of shearing. In this work, we conducted a benchmark study for three examples that involve different levels of complexity of intersecting fractures, and correspondingly different numbers of MPs. The codes and software that were used in the benchmark cover a range of continuum, discontinuum and hybrid numerical methods: NMM (LBNL), FLAC3D (LBNL), GBDEM (KIGAM), FRACOD (DynaFrax), and CASRock (CAS). The general consistency between DFN and MP cases as predicted by all the codes/software demonstrates that major paths can be used to simplify the geometry of DFNs in a wide range of software. Disagreement in results made by some software and potential future improvements are discussed. We show that (1) shearing of one or multiple major fractures can be reduced if there are multiple smaller intersecting fractures in that area, which is a useful basis for understanding and controlling induced seismicity and merits further analysis, and (2) the agreement achieved in the benchmark examples provide confidence that the simplified DFN model is a promising conceptual model that can be used for different types of numerical approaches and software for simplifying the analysis of the shearing of intersecting fractures and faults.

58 GEOSCIENCES↗

Analytical solutions to matrix diffusion problems

We report an analytical method to solve in a few cases of practical interest the equations which have traditionally been proposed for the matrix diffusion problem. In matrix diffusion, elements dissolved in ground water can penetrate the porous rock surronuding the advective flow paths. In the context of radioactive waste repositories this phenomenon provides a mechanism by which the area of rock surface in contact with advecting elements is greatly enhanced, and can thus be an important delay mechanism. The cases solved are relevant for laboratory as well for in situ experiments. Solutions are given as integral representations well suited for easy numerical solution.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Rock fracture processes in chemically reactive environments

Rock fracture is traditionally viewed as a brittle process involving damage nucleation and growth in a zone ahead of a larger fracture, resulting in fracture propagation once a threshold loading stress is exceeded. It is now increasingly recognized that coupled chemical-mechanical processes influence fracture growth in wide range of subsurface conditions that include igneous, metamorphic, and geothermal systems, and diagenetically reactive sedimentary systems with possible applications to hydrocarbon extraction and CO 2 sequestration. Fracture processes aided or driven by chemical change can affect the onset of fracture, fracture shape and branching characteristics, and fracture network geometry, thus influencing mechanical strength and flow properties of rock systems. We are investigating two fundamental modes of chemical-mechanical interactions associated with fracture growth: 1. Fracture propagation may be aided by chemical dissolution or hydration reactions at the fracture tip allowing fracture propagation under subcritical stress loading conditions. We are evaluating effects of environmental conditions on critical (fracture toughness KIc) and subcritical (subcritical index) fracture properties using double torsion fracture mechanics tests on shale and sandstone. Depending on rock composition, the presence of reactive aqueous fluids can increase or decrease KIc and/or subcritical index. 2. Fracture may be concurrent with distributed dissolution-precipitation reactions in the hostrock beyond the immediate vicinity of the fracture tip. Reconstructing the fracture opening history recorded in crack-seal fracture cement of deeply buried sandstone we find that fracture length growth and fracture opening can be decoupled, with a phase of initial length growth followed by a phase of dominant fracture opening. This suggests that mechanical crack-tip failure processes, possibly aided by chemical crack-tip weakening, and distributed solution-precipitation creep in the hostrock can independently affect fracture opening displacement and thus fracture aperture profiles and aperture distribution.

58 GEOSCIENCES↗

Thin liquid films in improved oil recovery from low-salinity brine

Low-salinity waterflooding is a relatively new method for improved oil recovery that has generated much interest. It is generally believed that low-salinity brine alters the wettability of oil reservoir rocks towards a wetting state that is optimal for recovery. The mechanism(s) by which the wettability alteration occurs is currently an unsettled issue. This study reviews recent studies on wettability alteration mechanisms that affect the interactions between the brine/oil and brine/rock interfaces of thin brine films that wet the surface of reservoir rocks. Of these mechanisms, we pay particular attention to double-layer expansion, which is closely tied to an increase in the thickness and stability of the thin brine films. Our review examines studies on both sandstones and carbonate rocks. We conclude that the thin-brine-film mechanisms provide a good qualitative, though incomplete, picture of this very complicated problem. Finally, we give suggestions for future studies that may help provide a more quantitative and complete understanding of low-salinity waterflooding.

02 PETROLEUM↗

Controlling Subsurface Fractures and Fluid Flow: A Basic Research Agenda

From beneath the surface of the earth, we currently obtain about 80-percent of the energy our nation consumes each year. In the future we have the potential to generate billions of watts of electrical power from clean, green, geothermal energy sources. Our planet’s subsurface can also serve as a reservoir for storing energy produced from intermittent sources such as wind and solar, and it could provide safe, long-term storage of excess carbon dioxide, energy waste products and other hazardous materials. However, it is impossible to underestimate the complexities of the subsurface world. These complexities challenge our ability to acquire the scientific knowledge needed for the efficient and safe exploitation of its resources. To more effectively harness subsurface resources while mitigating the impacts of developing and using these resources, the U.S. Department of Energy established SubTER – the Subsurface Technology and Engineering RD&D Crosscut team. This DOE multi-office team engaged scientists and engineers from the national laboratories to assess and make recommendations for improving energy-related subsurface engineering. The SubTER team produced a plan with the overall objective of “adaptive control of subsurface fractures and fluid flow.”This plan revolved around four core technological pillars—Intelligent Wellbore Systems that sustain the integrity of the wellbore environment; Subsurface Stress and Induced Seismicity programs that guide and optimize sustainable energy strategies while reducing the risks associated with subsurface injections; Permeability Manipulation studies that improve methods of enhancing, impeding and eliminating fluid flow; and New Subsurface Signals that transform our ability to see into and characterize subsurface systems. The SubTER team developed an extensive R&D plan for advancing technologies within these four core pillars and also identified several areas where new technologies would require additional basic research. In response, the Office of Science, through its Office of Basic Energy Science (BES), convened a roundtable consisting of 15 national lab, university and industry geoscience experts to brainstorm basic research areas that underpin the SubTER goals but are currently underrepresented in the BES research portfolio. Held in Germantown, Maryland on May 22, 2015, the round-table participants developed a basic research agenda that is detailed in this report. Highlights include the following: -A grand challenge calling for advanced imaging of stress and geological processes to help understand how stresses and chemical substances are distributed in the subsurface—knowledge that is critical to all aspects of subsurface engineering; -A priority research direction aimed at achieving control of fluid flow through fractured media; -A priority research direction aimed at better understanding how mechanical and geochemical perturbations to subsurface rock systems are coupled through fluid and mineral interactions; -A priority research direction aimed at studying the structure, permeability, reactivity and other properties of nanoporous rocks, like shale, which have become critical energy materials and exhibit important hallmarks of mesoscale materials; -A cross-cutting theme that would accelerate development of advanced computational methods to describe heterogeneous time-dependent geologic systems that could, among other potential benefits, provide new and vastly improved models of hydraulic fracturing and its environmental impacts; -A cross-cutting theme that would lead to the creation of “geo-architected materials” with controlled repeatable heterogeneity and structure that can be tested under a variety of thermal, hydraulic, chemical and mechanical conditions relevant to subsurface systems; -A cross-cutting theme calling for new laboratory studies on both natural and geo-architected subsurface materials that deploy advanced high-resolution 3D imaging and chemical analysis methods to determine the ;rates and mechanisms of fluid-rock processes, and to test predictive models of such phenomena. Many of the key energy challenges of the future demand a greater understanding of the subsurface world in all of its complexity. This greater under- standing will improve the ability to control and manipulate the subsurface world in ways that will benefit both the economy and the environment. This report provides specific basic research pathways to address some of the most fundamental issues of energy-related subsurface engineering.

15 GEOTHERMAL ENERGY↗

Mineral-Filled Fractures as Indicators of Multigenerational Fluid Flow in the Pahrump Hills Member of the Murray Formation, Gale Crater, Mars

Mineral-filled fractures (veins) are valuable indicators of deformation and fluid flow within a sedimentary package. Information obtained from vein morphology, texture, and chemistry may elucidate the sequence and nature of postdepositional fluid events. Additional information from vein patterns and interactions between veins and host rock provides insight into fracture formation mechanism(s). The widespread occurrence of veins and other diagenetic features in the sedimentary rock record preserved in Gale crater, Mars, indicates that postdepositional fluids were regionally active considerably later in time than the primary fluviolacustrine environments responsible for the deposition of Mount Sharp strata. Here we report a suite of veins within the Murray formation at the Pahrump Hills locality that were investigated using the scientific payload of the Mars Science Laboratory Curiosity rover. Based on an analysis of vein color, morphology, and texture, and corroborated by vein chemistry, we interpret three distinct vein types at Pahrump Hills: gray veins, white veins, and dark-toned veins. These veins represent distinct, separate episodes of postdepositional fluid flow, suggesting a protracted history of fluid stability in Gale crater. Additionally, we utilize vein patterns across multiple lithologies at the Pahrump Hills field site to suggest hydrofracture as the primary mechanism of fracture formation.

58 GEOSCIENCES↗

Computational Modeling of Hydraulic Properties of a Sheared Single Rock Fracture

Flow through a single mechanically sheared Marcellus shale fracture was investigated computationally and experimentally. To provide a better understanding of the variation of hydraulic and geometrical characteristics of a fracture subjected to shearing, coupled shear flow tests on the fracture for four shearing displacement steps under constant normal stress were performed. At the end of each shearing step, computed tomography (CT) scans with resolution 26.8 μm were obtained and the corresponding fracture geometries were evaluated. The CT images were used to generate full aperture maps of the fracture configuration. In addition, average aperture maps were also created by averaging the full-resolution data over 10 × 10 pixels, smoothing out fine structural details. Computational modeling of water flow through the fractures at different shearing steps was performed using a modified local cubic law approach and the 3D full Navier–Stokes equations with the use of the ANSYS-Fluent software. Both the average aperture maps and full maps were used in these simulations. The experimental pressure drops of the fracture at shearing step 1, which has very small apertures, poorly matched the numerical results, quite likely because the fracture structure was inadequately captured by the scanning resolution. Shearing typically increased the aperture height of the fracture, whose features were then better captured by the CT scan. Good agreement between the experimental data and the numerical results of the full map for shearing step 2 was observed. The simulations were performed for both full and average aperture maps, and the effects of scan resolution and surface roughness on the accuracy of the results were studied. The modified local cubic law and full Navier–Stokes simulations of the averaged map fracture were found to be in good agreement. It was conjectured that this was because the nonlinear losses were insignificant for the smoothed out averaged map fracture. Similar comparisons with those of the full map showed agreement in trends, but there were some quantitative differences. The averaged fracture map simulations also predicted lower pressure drops compared to the full map, particularly for high flow rates. These differences were due to the fine-scale geometrical complexity (surface roughness) of fracture geometry that affects the fluid flow in the fracture. In conclusion, an improved cubic law model was also proposed, and its accuracy was verified by comparing its predictions with those of the Navier–Stokes simulations.

58 GEOSCIENCES↗

Time–series Analysis of Volume Change at Brady Hot Springs, Nevada, USA using Geodetic Data from 2003 – 2018

Brady Hot Springs geothermal field has exhibited subsidence, as measured by interferometric synthetic aperture radar (InSAR). Previous studies have examined both the temporal evolution of the deformation from 2004 through 2016 and the spatial extent of the deformation, directly relating the observed subsidence to volumetric changes below the surface. We extend the modeling at Brady to analyze a data set of interferometric pairs spanning from the end of 2003 through 2018. We examine spatial and temporal trends in the observed deformation by time–series analysis of each of the 1656 cubic voxels in a parameterized elastic dislocation model to identify areas where the subsurface volume changes as a function of time. Joint time–series analysis of Global Positioning System and InSAR pairs confirm significant changes in rates of volume change during time intervals when well operations were varied. Here, the rate of subsidence increases with increased injection, consistent with the identification of thermal contraction of the rock matrix as the dominant driving mechanism. Conversely, the modeled volume increases when pumping ceases, suggesting thermal expansion of the rock matrix.

58 GEOSCIENCES↗