Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PIN”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Measurement of contact angle in a clearance-fit pin-loaded hole

A technique which measures load-contact variation in a clearance-fit, pin-loaded hole is presented in detail. A steel instrumented pin, which activates a make-or-break electrical circuit in the pin-hole contact region, was inserted into one aluminum and one polycarbonate specimen. The resulting load-contact variations are indicated schematically. The ability to accurately determine the arc of contact at any load was crucial to this measurement. It is noted that this simple experimental technique is applicable to both conducting and nonconducting materials.

Prabhakaran, R.↗

Magnetic properties of high-T(sub c) superconductors: Rigid levitation, flux pinning, thermal depinning, and fluctuation

The levitation of high-T(sub c) superconductors is quite conspicuous: Above magnets of low symmetry a disk of these ceramics floats motionless, without vibration or rotation; it has a continuous range of stable positions and orientations as if it were stuck in sand. Some specimens may even be suspended above or below the same magnet. This fascinating stability, inherent to no other type of levitation, is caused by the pinning of magnetic flux lines by inhomogeneities inside these extreme type-2 superconductors. The talk deals with pinning of magnetic flux in these materials, with flux flow, flux creep, thermally activated depinning, and the thermal fluctuation of the vortex positions in the flux line lattice (often called flux lattice melting). Also discussed are the fluctuations of the (nearly periodic) magnetic field inside these superconductors which are caused by random pinning sites and by the finite temperature. These fluctuations broaden the van-Hove singularities observed in the density of the magnetic field by nuclear magnetic resonance and by muon spin rotation.

Brandt, E. H.↗

Adjustably Preloaded Quick-Release Pin

Modified adjustable-grip-length quick-release pin holds two bodies together. Threaded shaft of pin threaded in floating nut to pretension fastener. Pin connects and disconnects rapidly and adjusted to accommodate small differences between thicknesses of nominally identical sets of parts to be attached to each other.

Reimers, Harold W.↗

Pin-Height Gauge

Gauge aligns itself and retains indication for later reading. Measuring tool indicates height of protrusion of pin from flat surface. Tool surrounds pin and holds itself square with flat surface, ensuring proper alignment and accuracy of measurement. Used in hard-to-see and hard-to-reach places. Holds indication of height until read. Metal scale slides in and out through slot in top plate. Scale value at slot gives height of pin under piston. Dimensions in inches.

Sumrall, Daniel R.↗

Heat transfer in thin, compact heat exchangers with circular, rectangular, or pin-fin flow passages

Heat transfer and pressure drop have been measured of three thin, compact heat exchangers in helium gas at 3.5 MPa and higher, with Reynolds numbers of 450 to 36,000. The flow geometries for the three heat exchanger specimens were: circular tube, rectangular channel, and staggered pin fin with tapered pins. The specimens were heated radiatively at heat fluxes up to 77 W/sq cm. Correlations were developed for the isothermal friction factor as a function of Reynolds number, and for the Nusselt number as a function of Reynolds number and the ratio of wall temperature to fluid temperature. The specimen with the pin fin internal geometry had significantly better heat transfer than the other specimens, but it also had higher pressure drop. For certain conditions of helium flow and heating, the temperature more than doubled from the inlet to the outlet of the specimens, producing large changes in gas velocity, density, viscosity, and thermal conductivity. These changes in properties did not affect the correlations for friction factor and Nusselt number in turbulent flow.

Olson, D. A.↗

Lever-Arm Pin Puller

Mechanism holds retaining pins in place except when actuated to release pins quickly. Mechanism is integral part of cover designed to be removed with simple downward motion of hand. Before removal, mechanism secures cover in place. After removal, mechanism holds retaining pins for reuse.

Macmartin, Malcolm↗

X-ray spectroscopy with silicon pin and avalanche photo diodes

Results of an evaluation of silicon P-Intrinsic-N (PIN) photodiodes and Avalanche Photodiodes (APD) for the direct detection of soft x rays from 1 to 20 keV and for the detection of scintillation light output from CsI(TI) for higher x ray energies (30 to 1000 keV) are presented. About one keV resolution was achieved at room temperature for both the PIN and APD detectors for soft x rays (1 to 20 keV). Commercially available, low power (18 mV), low noise, hybrid preamplifiers, were used. These photodiodes were also coupled to CsI(TI) scintillator and obtained about 6 resolution at 662 keV. The photodiode frequency response matches well with the emission spectrum of the CsI(TI) scintillator providing good spectral resolution and a higher signal than NaI(TI) when viewed by conventional photomultipliers. A PIN-CsI(TI) combination provides a low energy threshold of around 60 keV while for the APD-CsI(TI) it is 15 keV.

Desai, U. D.↗

Evaluation of Forces on the Welding Probe of the Automated Retractable Pin-Tool (RPT)

The NASA invention entitled 'The Hydraulic Controlled Auto-Adjustable Pin Tool for Friction Stir Welding' (US Patent 5,893,507), better known as the Retractable Pin-Tool (RPT), has been instrumented with a load-detecting device allowing the forces placed on the welding probe to be measured. As the welding probe is plunged into the material, the forces placed on the probe can now be characterized. Of particular interest are those forces experienced as the welding probe comes within close proximity to the back-up anvil. For a given material, it is believed that unique forces are generated relative to the distance between the welding probe and the anvil. The forces have been measured and characterized for several materials, and correlations have been made between these forces and the pin's position relative to the backside of the weld material.

Ding, R. J.↗

Evaluation of Forces on the Welding Probe of the Retractable Pin-Tool (RPT)

NASA invention entitled, "The Hydraulic Controlled Auto-Adjustable Pin Tool for Friction Stir Welding" (U.S. Patent 5,893,5 07), better known as the Retractable Pin-Tool (RPT) has been instrumented with a load detecting devise allowing the forces placed upon the welding probe to be measured. As the welding probe is plunged into the material, the forces placed upon the probe can now be charactefized. Of particular interest are those forces experienced as the welding probe comes within close proximity to the back-up anvil. For a given material, it is believed that unique forces are generated relative to the distance between the welding probe and the anvil. The forces have been measured and characterized for several materials, and correlations have been made between these forces and the pin's position relative to the backside of the weld material.

Ding, R. Jeffrey↗

Pin Tool Geometry Effects in Friction Stir Welding

In friction stir welding (FSW) there is significant evidence that material can take one of two different flow paths when being displaced from its original position in front of the pin tool to its final position in the wake of the weld. The geometry of the pin tool, along with the process parameters, plays an important role in dictating the path that the material takes. Each flow path will impart a different thermomechanical history on the material, consequently altering the material microstructure and subsequent weld properties. The intention of this research is to isolate the effect that different pin tool attributes have on the flow paths imparted on the FSWed material. Based on published weld tool geometries, a variety of weld tools were fabricated and used to join AA2219. Results from the tensile properties and microstructural characterization will be presented.

Querin, J. A.↗

Implementation of Pin Point Landing Vision Components in an FPGA System

Pin-point landing is required to enable missions to land close, typically within 10 meters, to scientifically important targets in generally hazardous terrain. In Pin Point Landing both high accuracy and high speed estimation of position and orientation is needed to provide input to the control system to safely choose and navigate to a safe landing site. A proposed algorithm called VISion aided Inertial NAVigation (VISINAV) has shown that the accuracy requirements can be met. [2][3] VISINAV was shown in software only, and was expected to use FPGA enhancements in the future to improve the computational speed needed for pin point landing during Entry Descent and Landing (EDL). Homography, feature detection and spatial correlation are computationally intensive parts of VISINAV. Homography aligns the map image with the descent image so that small correlation windows can be used, and feature detection provides regions that spatial correlation can track from frame to frame in order to estimate vehicle motion. On MER the image Homography, Feature Detection and Correlation would take approximately 650ms tracking 75 features between frames. We implemented Homography, Feature detection and Correlation on a Virtex 4 LX160 FPGA to run in under 25ms while tracking 500 features to improve algorithm reliability and throughput.

aircraft landing guidance↗

Silicon Alignment Pins: An Easy Way to Realize a Wafer-To-Wafer Alignment

A silicon alignment pin is used to align successive layers of components made in semiconductor chips and/or metallic components to make easier the assembly of devices having a layered structure. The pin is made as a compressible structure which can be squeezed to reduce its outer diameter, have one end fit into a corresponding alignment pocket or cavity defined in a layer of material to be assembled into a layered structure, and then allowed to expand to produce an interference fit with the cavity. The other end can then be inserted into a corresponding cavity defined in a surface of a second layer of material that mates with the first layer. The two layers are in registry when the pin is mated to both. Multiple layers can be assembled to create a multilayer structure. Examples of such devices are presented.

Jung-Kubiak, Cecile↗

Cooling system having reduced mass pin fins for components in a gas turbine engine

A cooling system having one or more pin fins with reduced mass for a gas turbine engine is disclosed. The cooling system may include one or more first surfaces defining at least a portion of the cooling system. The pin fin may extend from the surface defining the cooling system and may have a noncircular cross-section taken generally parallel to the surface and at least part of an outer surface of the cross-section forms at least a quartercircle. A downstream side of the pin fin may have a cavity to reduce mass, thereby creating a more efficient turbine airfoil.

42 ENGINEERING↗

Pin fin compliant heat sink with enhanced flexibility

Methods of using heat sinks include placing a pin fin compliant heat sink on a non-flat surface. The pin fin complaint heat sink has top and bottom plates connected by a plurality of pins arranged vertically between the top and bottom plates. The top and bottom plates are vertically conformed to local deviations of the non-flat surface. The top and bottom plates are laterally conformed to an overall shape of the surface. At least either the top or bottom plate is corrugated.

42 ENGINEERING↗

Pin base sensor for high-throughput macromolecular crystallography

Sensing methods and a compact, sample holding pin base sensor are provided for detecting if a sample pin is, for example, properly mounted on a goniometer used for automated, high throughput macromolecular crystallography. A first magnet is used for holding a magnetic base; a second magnet is disposed spaced apart from the first magnet. The first magnet and the second magnet have opposite orientation. A Hall-effect switch is located generally centrally between the first magnet and the second magnet. A state of the Hall-effect switch indicates if a sample pin is properly mounted on a mounting member, such as a goniometer.

Makarov, Oleg↗

Evaluation of rodded BWR assembly pin powers with simulate

In the development of Studsvik's nodal code SIMULATE5, special attention has been given to the accurate description of pin powers. The code solves the multi-group diffusion or simplified P3 equations with high spatial resolution. A short description is given of the handling of material heterogeneities in the axial and radial directions - the axial re-homogenization and the radial sub-mesh model, respectively. Furthermore, two models which are of special importance in the presence of control rods, and hence on the pellet clad interaction (PCI) phenomenon, are described; the quarter-assembly thermal-hydraulic treatment and the depletion of absorber material. A numerical example for a real core shows that while the impact of the fine grained description is negligible on global parameters such as k{sub eff}, the effect on pin powers may be substantial. For a deeply inserted and highly depleted control rod, the difference in pin powers caused by neglecting the advanced models of SIMULATE5, may be as high as 15 %. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Critical node treatment in the analytic function expansion method for Pin Power Reconstruction

Pin Power Reconstruction (PPR) was implemented in PARCS using the eight term analytic function expansion method (AFEN). This method has been demonstrated to be both accurate and efficient. However, similar to all the methods involving analytic functions, such as the analytic node method (ANM) and AFEN for nodal solution, the use of AFEN for PPR also has potential numerical issue with critical nodes. The conventional analytic functions are trigonometric or hyperbolic sine or cosine functions with an angular frequency proportional to buckling. For a critic al node the buckling is zero and the sine functions becomes zero, and the cosine function become unity. In this case, the eight terms of the analytic functions are no longer distinguishable from ea ch other which makes their corresponding coefficients can no longer be determined uniquely. The mode flux distribution of critical node can be linear while the conventional analytic functions can only express a uniform distribution. If there is critical or near critical node in a plane, the reconstructed pin power distribution is often be shown negative or very large values using the conventional method. In this paper, we propose a new method to avoid the numerical problem wit h critical nodes which uses modified trigonometric or hyperbolic sine functions which are the ratio of trigonometric or hyperbolic sine and its angular frequency. If there are no critical or near critical nodes present, the new pin power reconstruction method with modified analytic functions are equivalent to the conventional analytic functions. The new method is demonstrated using the L336C5 benchmark problem. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Pre-Transient Characterization of MLOF-1 Test Pin

This study focuses on the pre-transient characterization of U-10Zr test and sibling fuel pins for the THOR-M-LOF test series. Using neutron radiography, element contact profilometry (ECP), precise gamma scan (PGS), and gas assay, sampling, and recharge (GASR) analysis, it was confirmed that the fuel pins were intact and suitable for testing. Key fuel behaviors quantified include axial elongation, diametral strain, fluff structure geometry, axial isotope distribution, and fission gas release. Any deviations from historically expected behaviors were investigated and attributed to factors other than the irradiation behavior of the fuel pin. These pre-transient measurements establish a baseline for future post-transient analysis, which will be used to inform fuel performance models and safety criteria for sodium-cooled fast reactors (SFRs). The results will enhance understanding of transient fuel behavior and expand limited data on LOF scenarios.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗