Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “PHASE SHIFT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Two Heat-Transfer Improvements for Gas Liquefiers

Two improvements in heat-transfer design have been investigated with a view toward increasing the efficiency of refrigerators used to liquefy gases. The improvements could contribute to the development of relatively inexpensive, portable oxygen liquefiers for medical use. A description of the heat-transfer problem in a pulse-tube refrigerator is prerequisite to a meaningful description of the first improvement. In a pulse-tube refrigerator in particular, one of in-line configuration heat must be rejected from two locations: an aftercooler (where most of the heat is rejected) and a warm heat exchanger (where a small fraction of the total input power must be rejected as heat). Rejection of heat from the warm heat exchanger can be problematic because this heat exchanger is usually inside a vacuum vessel. When an acoustic-inertance tube is used to provide a phase shift needed in the pulse-tube cooling cycle, another problem arises: Inasmuch as the acoustic power in the acoustic-inertance tube is dissipated over the entire length of the tube, the gas in the tube must be warmer than the warm heat exchanger in order to reject heat at the warm heat exchanger. This is disadvantageous because the increase in viscosity with temperature causes an undesired increase in dissipation of acoustic energy and an undesired decrease in the achievable phase shift. Consequently, the overall performance of the pulse-tube refrigerator decreases with increasing temperature in the acoustic-inertance tube. In the first improvement, the acoustic-inertance tube is made to serve as the warm heat exchanger and to operate in an approximately isothermal condition at a lower temperature, thereby increasing the achievable phase shift and the overall performance of the refrigerator. This is accomplished by placing the acoustic-inertance tube inside another tube and pumping a cooling fluid (e.g., water) in the annular space between the tubes. Another benefit of this improvement is added flexibility of design to locate the warm heat-rejection components outside the vacuum vessel. The second improvement is the development of a compact radial-flow condenser characterized by a very high heat transfer coefficient and a small pressure drop.

Martin, Jerry L.↗
DOE OSTI2021

Phase effects from strong gravitational lensing of gravitational waves

Assessing the probability that two or more gravitational wave (GW) events are lensed images of the same source requires an understanding of the properties of the lensed images. For short enough wavelengths where wave effects can be neglected, lensed images will generically have a fixed relative phase shift that needs to be taken into account in the lensing hypothesis. For non-precessing, circular binaries dominated by quadrupole radiation these lensing phase shifts are degenerate with either a shift in the coalescence phase or a detector and inclination dependent shift in the orientation angle. This degeneracy is broken by the presence of higher harmonic modes with |m| ≠ 2 in the former and |m| ≠ l in the latter. The presence of precession or eccentricity will also break this degeneracy. This implies that a lensed GW image will not necessarily be consistent with (unlensed) predictions from general relativity (GR). Therefore, unlike the conventional scenario of electromagnetic waves, strong lensing of GWs can lead to images with a modified phase evolution that can be observed. However, we find that templates with a shifted orientation angle remain a good approximation, with signal-to-noise ratio differences of less than 1% for mass ratios up to 1/18, and less than 5% for precession parameters up to 0.5 and eccentricities up to 0.4. We conclude that an optimal strong lensing search strategy would incorporate phase information in all stages of the identification of strong-lensing, with an exact treatment in the final assessment of the probability of multiple lensed events. Here, this work clarifies the role that strong lensing plays in the phase evolution of GWs: how it can lead to apparent deviations from GR, how it can affect the detectability of GW events, and how it can be exploited to help identify cases of strong gravitational lensing of gravitational wave sources.

79 ASTRONOMY AND ASTROPHYSICS↗
NASA NTRS2019

Dynamic Characterization of the Crew Module Uprighting System for NASA’s Orion Crew Module

The Orion Crew Module Uprighting System is a set of five airbag that are responsible for the uprighting of the crew module in the case of an inverted splashdown. A series of tests during the Underway Recovery Test 7 (URT-7) were run in preparation for the Artemis I mission, where the dynamic characterization of the CMUS in an ocean wave environment was performed. A Datawell Waverider DWR-G4 wave buoy was deployed to the characterize the wave environment during these tests. The heave measurements from this buoy were projected to the Orion Crew Module Buoyancy Test Article location by two different methods: (1) directly time-shifting the data, and (2) performing a frequency-domain, phase-shifting operation. Results demonstrate that the phase-shifting operation led to better correlation with the true crew module response to wave excitation as compared with the purely time-shifted method. Additionally, a novel approach to localize an object in a bidirectional wave field based on its heave response is presented and validated with URT- 7 data. Given a wave measurement device at a known location, one can estimate the relative distance to another object based solely off its heave response. Results show that if signals have sufficiently good correlation, this method can be used to estimate the relative separation between two objects in the same wave field.

Vertaska, Ivan Bertaska↗
DOE OSTI2015

A general theory of interference fringes in x-ray phase grating imaging

Purpose: The authors note that the concept of the Talbot self-image distance in x-ray phase grating interferometry is indeed not well defined for polychromatic x-rays, because both the grating phase shift and the fractional Talbot distances are all x-ray wavelength-dependent. For x-ray interferometry optimization, there is a need for a quantitative theory that is able to predict if a good intensity modulation is attainable at a given grating-to-detector distance. In this work, the authors set out to meet this need. Methods: In order to apply Fourier analysis directly to the intensity fringe patterns of two-dimensional and one-dimensional phase grating interferometers, the authors start their derivation from a general phase space theory of x-ray phase-contrast imaging. Unlike previous Fourier analyses, the authors evolved the Wigner distribution to obtain closed-form expressions of the Fourier coefficients of the intensity fringes for any grating-to-detector distance, even if it is not a fractional Talbot distance. Results: The developed theory determines the visibility of any diffraction order as a function of the grating-to-detector distance, the phase shift of the grating, and the x-ray spectrum. The authors demonstrate that the visibilities of diffraction orders can serve as the indicators of the underlying interference intensity modulation. Applying the theory to the conventional and inverse geometry configurations of single-grating interferometers, the authors demonstrated that the proposed theory provides a quantitative tool for the grating interferometer optimization with or without the Talbot-distance constraints. Conclusions: In this work, the authors developed a novel theory of the interference intensity fringes in phase grating x-ray interferometry. This theory provides a quantitative tool in design optimization of phase grating x-ray interferometers.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2016

Recent advances in Lorentz microscopy

Lorentz transmission electron microscopy (LTEM) has evolved from a qualitative magnetic domain observation technique to a quantitative technique for the determination of the magnetization state of a sample. Here, we describe recent developments in techniques and imaging modes, including the use of spherical aberration correction to improve the spatial resolution of LTEM into the single nanometer range, and novel in situ observation modes. We also review recent advances in the modeling of the wave optical magnetic phase shift as well as in the area of phase reconstruction by means of the Transport of Intensity Equation (TIE) approach, and discuss vector field electron tomography, which has emerged as a powerful tool for the 3D reconstruction of magnetization configurations. Finally, we conclude this review with a brief overview of recent LTEM applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Upgraded fiber-optic sensor system for dynamic strain measurement in Spallation Neutron Source

We describe an upgraded fiber-optic sensor system and its performance in measuring the dynamic strains in a mercury target of the Spallation Neutron Source (SNS). Strains result from dynamic pressure waves in the stainless-steel mercury target induced by short (~700 ns), intense (up to 23.3 kJ), high-energy (~1 GeV) proton pulses. In the upgraded sensor system, the output of each sensor head is interrogated with a compact, all-fiber based Faraday Michelson interferometer, which generates interference signals with a steady phase shift. Strain waveforms are recovered from the phase-shifted interference signals using a high-speed digital signal processing procedure developed in our previous work. We demonstrate successful measurements of dynamic strain pulses, e.g., 400με over 190μs , on a recently installed SNS target using the upgraded sensor system. The measured strain waveforms are analyzed for more than 20 sensor locations and/or orientations, and provide information regarding the temporal structure of strain profiles and dependence of the strain magnitude on the proton powers of 200 – 1400 kW. The new interrogator also measures the radiation-induced-attenuation (RIA) in the optical fiber, enabling experimental investigations of RIA profiles induced by a 700-ns radiation pulse. The radiation effects on the strain measurement performance are discussed over a radiation dose range of up to 4×10 8 Gy and an RIA compensation method is proposed. The measurements allow insight into the response of this unique piece of equipment and can be used for validation of simulations.

47 OTHER INSTRUMENTATION↗
NASA NTRS1981

Summary of the status of the Nimbus-7 SMMR

The present state of calibration of the Nimbus-7 SMMR is described, and its relevance to retrievals of sea surface temperatures is discussed. The asymmetry in the polarization rotation was studied by calibrating the SMMR signals without the polarization rotation correction within a data set consisting of about 300 orbits, and the phase shift was determined by regression analysis. The largest phase shift was observed in the 1.4 cm vertical polarization channel - almost 11 degrees. The in-orbit calibration adjustment scheme is described, and the result of applying it to the 4.6 cm vertical polarization channel is shown.

Gloersen, P.↗
NASA NTRS1986

DSP-based non-coherent dual detector demodulator for land mobile radio channels

This paper outlines the development of a digital demodulator suitable for the non-coherent detection of various modulation formats including: Phase Shift Keying (PSK), Continuous Phase Frequency Shift Keying (CPFSK) and Frequency Modulation (FM). The demodulator design concept has been derived with a view towards a single integrated circuit (IC) implementation. Two detectors, one non-coherent and one differentially coherent, operate concurrently, providing data detection and automatic frequency control (AFC). Bit error rate results are provided which illustrate the receiver performance in white Gaussian noise.

Saulnier, Gary J.↗
NASA NTRS2004

Adaptive Controls Method Demonstrated for the Active Suppression of Instabilities in Engine Combustors

An adaptive feedback control method was demonstrated that suppresses thermoacoustic instabilities in a liquid-fueled combustor of a type used in aircraft engines. Extensive research has been done to develop lean-burning (low fuel-to-air ratio) combustors that can reduce emissions throughout the mission cycle to reduce the environmental impact of aerospace propulsion systems. However, these lean-burning combustors are susceptible to thermoacoustic instabilities (high-frequency pressure waves), which can fatigue combustor components and even the downstream turbine blades. This can significantly decrease the safe operating lives of the combustor and turbine. Thus, suppressing the thermoacoustic combustor instabilities is an enabling technology for lean, low-emissions combustors under NASA's Propulsion and Power Program. This control methodology has been developed and tested in a partnership of the NASA Glenn Research Center, Pratt & Whitney, United Technologies Research Center, and the Georgia Institute of Technology. Initial combustor rig testing of the controls algorithm was completed during 2002. Subsequently, the test results were analyzed and improvements to the method were incorporated in 2003, which culminated in the final status of this controls algorithm. This control methodology is based on adaptive phase shifting. The combustor pressure oscillations are sensed and phase shifted, and a high-frequency fuel valve is actuated to put pressure oscillations into the combustor to cancel pressure oscillations produced by the instability.

Kopasakis, George↗
NASA NTRS2005

Ka-Band, MEMS Switched Line Phase Shifters Implemented in Finite Ground Coplanar Waveguide

Ka-band MEMS switched line phase shifters implemented in finite ground coplanar waveguide are described in this paper. The phase shifters are constructed of single-pole double-throw (SPDT) switches with additional reference and phase offset transmission line lengths. The one- and two-bit phase shifters are fabricated on high resistivity (HR) silicon with a dielectric constant, Epsilon(sub T) = 11.7 and a substrate thickness, t = 500microns. The switching architectures integrated within the phase shifters consist of MEMS switches that are doubly anchored cantilever beam capacitive switches with additional high inductive sections (MEMS LC device). The SPDT switch is composed of a T-junction with a MEMS LC device at each output port. The one-bit phase shifter described in this paper has an insertion loss (IL) and return loss (RL) of 0.9 dB and 30 dB while the two-bit described has an IL and RL of 1.8 dB and 30 dB respectively. The one-bit phase shifter's designed offset phase is 22.5deg and actual measured phase shift is 21.8deg. The two-bit phase shifter's designed offset phase is 22.5deg, 45deg, and 67.5deg and the actual measured phase shifts are 21.4deg, 44.2deg, and 65.8deg, respectively.

Scardelletti, Maximilian C.↗
DOE OSTI2019

Generalised hyper-Ramsey resonance with spinors

The generalised hyper-Ramsey resonance formula originally published in Phys. Rev. A, 92, 023416 (2015) is derived using a Cayley – Klein spinor parametrisation. The shape of the interferometric resonance and the associated composite phase shift are reformulated including all individual laser pulse parameters. Potential robustness of signal contrast and phase-shift of the wave-function fringe pattern can now be arbitrarily explored tracking any shape distortion due to systematic effects from the probe laser. An exact and simple analytical expression describing Ramsey’s method of separated composite oscillating laser fields with quantum state control allows us to accurately simulate all recent clock interrogation protocols under various pulse defects. (selected papers presented at the viii symposium 'mplp-2018')

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2024

Optimal function estimation with photonic quantum sensor networks

The problem of optimally measuring an analytic function of unknown local parameters each linearly coupled to a qubit sensor is well understood, with applications ranging from field interpolation to noise characterization. Here we resolve a number of open questions that arise when extending this framework to Mach-Zehnder interferometers and quadrature displacement sensing. In particular, we derive lower bounds on the achievable mean square error in estimating a linear function of either local phase shifts or quadrature displacements. In the case of local phase shifts, these results prove, and somewhat generalize, a conjecture by Proctor []. For quadrature displacements, we extend proofs of lower bounds to the case of arbitrary linear functions. We provide optimal protocols achieving these bounds up to small (multiplicative) constants and describe an algebraic approach to deriving new optimal protocols, possibly subject to additional constraints. Using this approach, we prove necessary conditions for the amount of entanglement needed for any optimal protocol for both local phase and displacement sensing. Published by the American Physical Society 2024

Bringewatt, Jacob↗
NASA NTRS1988

Digital carrier demodulation for the DSN Advanced Receiver

The digital in-phase and quadrature (I and Q) carrier demodulation for the Deep Space Network's (DSN) Advanced Receiver is described and analyzed. The system provides coherent demodulation for a variety of modulation formats including Binary Phase Shift Keying (BPSK), BPSK with a carrier residual, Quadrature Phase Shift Keying (QPSK), Offset-QPSK (OQPSK), and Minimum Shift Keying (MSK). The focus is on the theory and hardware design of the halfband filters which are the integral part of the demodulator. The underlying theory of the filters is summarized, a breadboard hardware design is described, and a VLSI implementation is proposed which significantly decreases the hardware. A second important problem analyzed is DC-offset in the demodulator. This is a serious problem which translates into bias error in the residual carrier phase detector. The dynamic range of the complex mixer is analyzed using a probabilistic approach. It is deduced that the resulting static phase error is less than 0.2 deg when the ratio of carrier power to noise power in the demodulator input bandwidth is -72 dB or higher. Thus, the static phase error is negligible at a carrier power to noise spectral density of 0 dB-Hz for a 15 MHz bandwidth demodulator.

Sadr, R.↗
DOE OSTI2015

Terahertz wavefront control by tunable metasurface made of graphene ribbons

We propose a tunable metasurface consisting of an array of graphene ribbons on a silver mirror with a SiO{sub 2} gap layer to control reflected wavefront at terahertz frequencies. The graphene ribbons exhibit localized plasmon resonances depending on their Fermi levels to introduce abrupt phase shifts along the metasurface. With interference of the Fabry-Perot resonances in the SiO{sub 2} layer, phase shift through the system is largely accumulated, covering the 0-to-2π range for full control of the wavefront. Numerical simulations prove that wide-angle beam steering up to 53° with a high reflection efficiency of 60% is achieved at 5 THz within a switching time shorter than 0.6 ps.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2018

A free-standing wire scattering technique to monitor calibration variations of the DIII-D density profile reflectometer

Real-time phase calibration of the ITER profile reflectometer is essential due to the long plasma duration and expected waveguide path length changes during a discharge. Progress has been recently made in addressing this issue by employing a phase calibration technique on DIII-D that monitors calibration variations that occur during each plasma discharge. By installing a thin free-standing metallic wire (1 mm diameter) near the end of the overmoded waveguide transmission system (oriented perpendicular to the waveguide axis), the round-trip phase shift from the wire is detected simultaneously with the plasma phase shifts. Variations in the reflectometer round trip path length (-26 m) are then calculated after each DIII-D plasma discharge, allowing the calibration phase to be accurately monitored and updated. The round-trip reflectometer path length is observed to vary by -3 mm (root mean square value) during a typical DIII-D discharge. Using the variations in calibration phase, the density profile measurement accuracy can be improved. Since the wire retro-reflected power is -0.01 of the plasma signal, minimal effect is observed on the reflected signal from the plasma. Importantly, through a suitable choice in wire diameter, the calibration signal can be made approximately independent of the V-band reflectometer launch polarization. Furthermore, this is particularly important on DIII-D since orthogonal X- and O-mode polarized beams are coupled into the same transmission waveguide and launch antenna.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

An efficient reconstruction algorithm for differential phase-contrast tomographic images from a limited number of views

The main focus of this paper is reconstruction of tomographic phase-contrast image from a set of projections. We propose an efficient reconstruction algorithm for differential phase-contrast computed tomography that can considerably reduce the number of projections required for reconstruction. The key result underlying this research is a projection theorem that states that the second derivative of the projection set is linearly related to the Laplacian of the tomographic image. The proposed algorithm first reconstructs the Laplacian image of the phase-shift distribution from the second-derivative of the projections using total variation regularization. The second step is to obtain the phase-shift distribution by solving a Poisson equation whose source is the Laplacian image previously reconstructed under the Dirichlet condition. We demonstrate the efficacy of this algorithm using both synthetically generated simulation data and projection data acquired experimentally at a synchrotron. The experimental phase data were acquired from a human coronary artery specimen using dark-field-imaging optics pioneered by our group. Our results demonstrate that the proposed algorithm can reduce the number of projections to approximately 33% as compared with the conventional filtered backprojection method, without any detrimental effect on the image quality.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2015

Interactions of nonlinear electron-acoustic solitary waves with vortex electron distribution

In the present work, based on a one dimensional model, we consider the head-on-collision of nonlinear electron-acoustic waves in a plasma composed of a cold electron fluid, hot electrons obeying a trapped/vortex-like distribution, and stationary ions. The analysis is based on the use of extended Poincare, Lighthill-Kuo method [C. H. Su and R. M. Mirie, J. Fluid Mech. 98, 509 (1980); R. M. Mirie and C. H. Su, J. Fluid Mech. 115, 475 (1982)]. It is shown that, for the first order approximation, the waves propagating in opposite directions are characterized by modified Korteweg-de Vries equations. In contrary to the results of previous investigations on this subject, we showed that the phase shifts are functions of both amplitudes of the colliding waves. The numerical results indicate that the waves with larger amplitude experience smaller phase shifts. Such a result seems to be plausible from physical considerations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
NASA NTRS1981

Optical gyroscope system

Light beams pass in opposite directions through a single mode fiber optic wave guide that extends in a circle or coil in an optical gyroscope system which measures the rotation rate of the coil by measuring the relative phase shifts of the beams by interferometric techniques. Beam splitting and phase shifting of the light are facilitated by utilizing brief pulses of light and by using light-controlling devices which are operated for a brief time only when the light pulse passes in one direction through the device but not at a different time when the pulse is passing in the opposite direction through the device. High accuracy in rotation measurement is achieved at both very slow and very fast rotation rates, by alternately operating the system so that at zero rotation the interfering waves are alternately 90 out of phase and in phase. Linear polarization of the light beams is maintained by coiling the full length of the optic fiber in a single plane.

Goss, W. C.↗