Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Nuclear Fuel Performance Simulation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

BWR Spent Nuclear Fuel Interfacial Bonding Efficiency Study

The objective of this project is to perform a systematic study of spent nuclear fuel (SNF, also known as “used nuclear fuel” [UNF]) integrity under simulated transportation environments using the Cyclic Integrated Reversible-Bending Fatigue Tester (CIRFT) hot-cell testing technology developed at Oak Ridge National Laboratory (ORNL) in August 2013. Under Nuclear Regulatory Commission (NRC) sponsorship, ORNL completed four benchmark tests, four static tests, and twelve dynamic or cycle tests on H. B. Robinson (HBR) high burn-up (HBU) fuel. The clad of the HBR fuels was made of Zircaloy-4. Testing was continued in fiscal year (FY) 2014 using Department of Energy (DOE) funds. Additional CIRFT testing was conducted on three HBR rods; two specimens failed, and one specimen was tested to over 2.23 × 10 7 cycles without failing. The data analysis on all the HBR SNF rods demonstrated that it is necessary to characterize the fatigue life of the SNF rods in terms of (1) the curvature amplitude and (2) the maximum absolute of curvature extremes. The maximum extremes are significant because they signify the maximum tensile stress for the outer fiber of the bending rod. CIRFT testing has also addressed a large variation in hydrogen content on the HBR rods. While the load amplitude is the dominant factor that controls the fatigue life of bending rods, the hydrogen content also has an important effect on the lifetime attained at each load range tested. In FY 15, eleven SNF rod segments from the Limerick BWR were tested using the ORNL CIRFT equipment; one test under static conditions and ten tests under dynamic loading conditions. Under static unidirectional loading, a moment of 85 N·m was obtained at a maximum curvature of 4.0 m -1 . The specimen did not show any sign of failure during three repeated loading cycles to a similar maximum curvature. Ten cyclic tests were conducted with amplitudes varying from 15.2 to 7.1 N·m. Failure was observed in nine of the tested rod specimens. The cycles-to-failure ranged from 1.22 × 10 5 to 4.70 × 10 6 , and the amplitudes varied from 15.2 to 7.6 N·m. The measurements at the interrupts indicated a range of flexural rigidity from 30 to 50 N·m 2 . Online monitoring revealed that the flexural rigidity was slightly lower due to the higher loading, from 25 to 42 N·m 2 . Generally, no substantial change of rigidity was observed based on the online monitoring during the cyclic fatigue testing process. Overall, the decreasing trend of sample lifetime with increasing amplitude is well defined.

interface bonding efficiency↗

Post irradiation analysis and performance modeling of dispersion and monolithic U-Mo fuels

We analyzed fission product swelling of post-irradiation U-Mo fuels from the early RERTR tests to the recent RERTR-8 test. We found that the gas bubble swelling of the fuel-swelling model was overestimated. From the recent tests, RERTR-7A and 8, we could also collect a considerable amount of fuel swelling data from monolithic U-Mo fuel plates. The fuel swelling data from the monolithic fuel plates are considered more reliable because the interaction layer growth between the fuel and matrix in dispersion fuel, which obscures fuel swelling, does not exist. The swelling correlation comparison to the Si-added dispersion fuel data and monolithic fuel data suggested that a modification of the existing model was necessary. We also developed an interaction layer growth model for U-Mo/Al dispersion fuel plates with a Si-added matrix. PLATE code calculations with the new PIE data analysis results were performed. The updated versions predict with better accuracies for both monolithic fuel plates and dispersion fuel plates. In this paper, we present the results of fission product swelling characterization. In addition, the interaction layer growth model for U-Mo/Al with a Si-added matrix is presented. (author)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Coupling procedure for TRANSURANUS and KTF codes

The nuclear industry aims to ensure safe and economic operation of each single fuel rod introduced in the reactor core. This goal is even more challenging nowadays due to the current strategy of going for higher burn-up (fuel cycles of 18 or 24 months) and longer residence time. In order to achieve that goal, fuel modeling is the key to predict the fuel rod behavior and lifetime under thermal and pressure loads, corrosion and irradiation. In this context, fuel performance codes, such as TRANSURANUS, are used to improve the fuel rod design. The modeling capabilities of the above mentioned tools can be significantly improved if they are coupled with a thermal-hydraulic code in order to have a better description of the flow conditions within the rod bundle. For LWR applications, a good representation of the two phase flow within the fuel assembly is necessary in order to have a best estimate calculation of the heat transfer inside the bundle. In this paper we present the coupling methodology of TRANSURANUS with KTF (Karlsruhe Two phase Flow subchannel code) as well as selected results of the coupling proof of principle. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Buffer-IPyC separation process in TRISO fuel particles simulated with Bison code

During High Temperature Gas-cooled Reactor (HTGR) operation, tristructural isotropic (TRISO) coated-particle fuel undergoes irradiation-induced changes in morphology and thermomechanical properties. Experimental results from the Advanced Gas Reactor (AGR) Fuel Development and Qualification Program show, among other things, the mechanism of gap formation between the buffer and inner pyrolytic carbon (IPyC) layers, which could be explored further via computational simulations using the Bison code. Two simulation models were developed, the debonding restricted model, where no gap formation between buffer and IPyC layers is permitted, and the debonding enabled model, where the gap between those layers is created. The inputs of the simulated models are based on the irradiation conditions from the AGR-1 experiment. The research included simulations on spherical and aspherical fuel types. Under the specific temperatures and fluences of the AGR-1 irradiation experiment, and the Bison simulations, it was concluded that the most common scenario is a gap formation along the buffer-IPyC interface, while the least possible scenario is the situation where there is no gap formation at the buffer-IPyC junction. The computational results confirmed that the sphericity of the fuel influences the thickness of the gap that occurs at the buffer-IPyC junction, in a way that with increasing aspect ratio the gap thickness increases. The results obtained for spherical and aspherical fuel are nearly identical. Finally, performed simulations match conclusions observed from the AGR-1 experiment, which as such shows that the Bison code is a good computational method for simulating the TRISO fuel. Future simulations will include the validation of performed research and comparison of the results between Bison and PARFUME codes.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Deployment of BISON models of fuel restructuring at high burnup and related fission gas behavior in UO 2

This milestone report details the advancements made in fiscal year 2024 under the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program to improve the modeling of fission gas behavior in high burnup UO 2 nuclear fuel in the BISON fuel performance code. As nuclear fuel is pushed to higher burnups, significant microstructural changes occur within the fuel, including the formation of a high burnup structure (HBS) on the pellet rim and a dark zone deeper within the pellet. These regions, characterized by subgrain formation and increased pore densities, have critical implications for fission gas behavior and release, which are not well understood. The modeling capabilities in BISON did not adequately predict these phenomena, leading to an underestimation of fuel restructuring and - potentially - of fission gas release. To address these gaps, this milestone focused on three key objectives: (1) reviewing and assessing Sifgrs's capabilities for low burnup fuel, on which high burnup capabilities rely, (2) validating and expanding HBS fission gas modeling capabilities, including investigating mechanisms for fission gas release from HBS, and (3) expanding Sifgrs to enable modeling of dark zone formation and its effects on fission gas behavior. These objectives were achieved and are described herein. The achievements of this NEAMS milestone are significant for the industry's goal of burnup extension. The improved predictive modeling capabilities for both low- and high-burnup conditions enhance our understanding of fuel performance under both normal operations and transient scenarios. Although goals were reached, future work is necessary to validate these models against experimental data and quantify their accuracy in different conditions. In parallel, mechanistic modeling efforts should continue to extend and refine these capabilities to increase accuracy while reducing reliance on empirical models. This will ensure robust performance across a broader range of conditions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The defect chemistry of U O 2 ± x from atomistic simulations

Control of the defect chemistry in UO 2±x is important for manipulating nuclear fuel properties and fuel performance. For example, the uranium vacancy concentration is critical for fission gas release and sintering, while all oxygen and uranium defects are known to strongly influence thermal conductivity. Here the point defect concentrations in thermal equilibrium are predicted using defect energies from density functional theory (DFT) and vibrational entropies calculated using empirical potentials. Electrons and holes have been treated in a similar fashion to other charged defects allowing for structural relaxation around the localized electronic defects. Predictions are made for the defect concentrations and non-stoichiometry of UO 2±x as a function of oxygen partial pressure and temperature. If vibrational entropy is omitted, oxygen interstitials are predicted to be the dominant mechanism of excess oxygen accommodation over only a small temperature range (1265 K to 1350 K), in contrast to experimental observation. Conversely, if vibrational entropy is included oxygen interstitials dominate from 1165 K to 1680 K (Busker potential) or from 1275 K to 1630 K (CRG potential). Below these temperature ranges excess oxygen is predicted to be accommodated by uranium vacancies, while above them the system is hypo-stoichiometric with oxygen deficiency accommodated by oxygen vacancies. Our results are discussed in the context of oxygen clustering, formation of U 4 O 9 , and issues for fuel behavior. In particular, the variation of the uranium vacancy concentrations as a function of temperature and oxygen partial pressure will underpin future studies into fission gas diffusivity and broaden the understanding of UO 2±x sintering.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Production Through Simulation: Using Simulation Technologies to Create and Evaluate Nuclear Fuel Fabrication Facility Designs

This project explores how physics-based and discrete-event simulation technologies can be jointly employed to model a suite of nuclear fuel fabrication facility designs with variable radiological environments, optimize their design to lower operational costs subject to a set of design constraints, and evaluate their performance. Initially, three variants of U-20Pu-10Zr metallic nuclear fuel in three specific geometric configurations are modeled and studied across more than 50 physics simulations in nuclear physics software packages SCALE and Monte Carlo N-Particle Transport (MCNP6.2). From these tests, values for effective dose rate and criticality are recorded for each of the nine alloy-geometry configurations. These values are then incorporated into discrete-event models of fuel fabrication in the simulation program ExtendSim Pro 10 as process attributes. This allows one to track the dose to facility personnel as fuel is fabricated, dually enabling us to evaluate the safety of a given facility design in terms of absorbed dose per worker per year and to craft operational guidelines that adhere to federal and local safety regulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Modeling of fission and activation products in molten salt reactors and their potential impact on the radionuclide monitoring stations of the International Monitoring System

Molten Salt Reactors (MSRs) are one of six Generation IV reactor designs currently under development around the world. Because of the unique operating conditions of MSRs, which include molten fuel and the continuous removal of gaseous fission products during operation, work was performed to analyze the potential impact of emissions on the International Monitoring System (IMS) of the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Simulations were performed to predict the production of IMS-relevant radionuclides in four MSR designs operating under two scenarios – (1) a sealed reactor with releases only during operational shutdown and (2) continuous reprocessing or sparging of the fuel salt. From these production estimates the radioxenon and radioiodine signatures were extracted and compared to three current reactor designs (PWR, BWR, RBMK). In the cases where continuous reprocessing of the fuel salt occurred both the radioxenon and radioiodine signatures are nearly indistinguishable from a nuclear explosion. Estimates were also made of the potential emission rate of radioxenon for three reactor designs and it was found that MSRs have the potential to emit radioxenon isotopes at a rate of 1015 – 8×1016 Bq/d for 133Xe if no abatement is used. An assessment was also made of activation products using a candidate fuel salt (FLiBe) mixed with corrosion products for the Thorium Molten Salt Reactor (TMSR-LF1)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Sensitivity Analysis of FEAST-Metal Fuel Performance Code: Initial Results

This memo documents the completion of the LANL milestone, M3FT-12LA0202041, describing methodologies and initial results using FEAST-Metal. The FEAST-Metal code calculations for this work are being conducted at LANL in support of on-going activities related to sensitivity analysis of fuel performance codes. The objective is to identify important macroscopic parameters of interest to modeling and simulation of metallic fuel performance. This report summarizes our preliminary results for the sensitivity analysis using 6 calibration datasets for metallic fuel developed at ANL for EBR-II experiments. Sensitivity ranking methodology was deployed to narrow down the selected parameters for the current study. There are approximately 84 calibration parameters in the FEAST-Metal code, of which 32 were ultimately used in Phase II of this study. Preliminary results of this sensitivity analysis led to the following ranking of FEAST models for future calibration and improvements: fuel conductivity, fission gas transport/release, fuel creep, and precipitation kinetics. More validation data is needed to validate calibrated parameter distributions for future uncertainty quantification studies with FEAST-Metal. Results of this study also served to point out some code deficiencies and possible errors, and these are being investigated in order to determine root causes and to improve upon the existing code models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Standalone BISON Fuel Performance Results for Watts Bar Unit 1, Cycles 1-3

The Consortium for Advanced Simulation of Light Water Reactors (CASL) is moving forward with more complex multiphysics simulations and increased focus on incorporating fuel performance analysis methods. The coupled neutronics/thermal-hydraulics capabilities within the Virtual Environment for Reactor Applications Core Simulator (VERA-CS) have become relatively stable, and major advances have been made in analysis efforts, including the simulation of twelve cycles of Watts Bar Nuclear Unit 1 (WBN1) operation. While this is a major achievement, the VERA-CS approaches for treating fuel pin heat transfer have well-known limitations that could be eliminated through better integration with the BISON fuel performance code.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Experiment Isotopic Data Compiled by the OECD/NEA Expert Group on Assay Data for Spent Nuclear Fuel

An essential component of computational modeling and simulation is the availability of well-qualified experimental benchmark data against which calculation systems can be validated and the bias and uncertainty associated with the codes and data can be evaluated. The validation process is extremely important for safety and licensing to demonstrate that adequate margins for uncertainty have been included in the calculations. For safety evaluations involving spent nuclear fuel, the isotopic compositions and resulting activities calculated using depletion and decay codes must be validated against experimental determinations of the spent fuel content. In this process the isotopic concentrations predicted by the codes should be compared with corresponding measurements of spent fuel made by destructive analysis as a fundamental part of any code performance evaluation. In recent years there has been growing international interest in acquiring high-quality assay data that can be used to validate code calculations, particularly for modern fuel designs and high burnup fuels and for a wider range of nuclides important to nuclear criticality safety, radiological safety assessments, and decay heat. Assay data are required to validate a broad range of reactor and fuel-cycle applications, including reactor core simulation, postulated severe accident analysis, spent fuel handling, spent fuel transportation and interim storage, reprocessing, nuclear safeguards, and final fuel repository evaluations. In some cases researchers working on depletion code development have noted a general lack of available assay measurements that can be used to benchmark and validate their code calculations for spent fuel compositions. This perception is due in part to the fact that data have been reported in diverse publications over many years, many experimental reports are difficult to access, and there has not been a concerted and funded effort to compile and consolidate available measurements that can be easily accessed by code developers and analysts for validation. In response to the increased interest in fuel isotopic measurements and needs for consolidation and documentation of available data, an Expert Group on Assay Data for Spent Nuclear Fuel (EGADSNF) was formed in 2007 as a working group of the Organisation for Economic Cooperation and Development (OECD)/Nuclear Energy Agency (NEA) Working Party on Nuclear Criticality Safety (WPNCS). Although the group was formed by the Expert Group on Burnup Credit to coordinate isotopic assay data activities and facilitate collaboration between countries developing or implementing burnup credit in their nuclear criticality safety methodologies, the group recognized the need and value of assay data for a broad range of spent fuel applications, and the EGADSNF includes members representing not only the WPNCS, but also members from the standing technical Committee on the Safety of Nuclear Installations and the Integration Group for the Safety Case of the Radioactive Waste Management Committee. Member countries currently active in the EGADSNF include Belgium, the Czech Republic, France, Germany, Japan, Slovakia, Spain, Sweden, the United Kingdom, and the United States. The experimental database of spent fuel measurements maintained by the OECD/NEA is web-accessible. SFCOMPO (database of Spent Fuel Compositions) contains measured isotopic data, mostly for light water reactor (LWR) fuels, for about 250 fuel samples. This paper summarizes the status of SFCOMPO and current activities to expand and improve the database.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Plasma sprayed and electrospark deposited zirconium metal diffusion barrier coatings

Zirconium metal coatings applied by plasma spraying and electrospark deposition (ESD) have been investigated for use as diffusion barrier coatings on low enrichment uranium fuel for research nuclear reactors. The coatings have been applied to both stainless steel as a surrogate and to simulated nuclear fuel uranium-molybdenum alloy substrates. Deposition parameter development accompanied by coating characterization has been performed. The structure of the plasma sprayed coating was shown to vary with transferred arc current during deposition. The structure of ESD coatings was shown to vary with the capacitance of the deposition equipment.

36 MATERIALS SCIENCE↗

A New Reduced Order Model For The Mechanistic Creep Behavior Of UO 2

This manuscript describes an ongoing NEAMS effort to better determine the performance of advanced nuclear fuels, in particular the creep behavior of doped UO$_2$ for light water reactors. In our previous work, we outlined a method to utilize data generated from lower length scale simulations and implement it into the engineering scale fuel performance analysis. This process has been further refined, and in addition, new data has been used to train the surrogate model which has also been substantially improved since the previous iteration. The new model is compared against the current empirical model used in BISON using both scoping calculations to define the performance over the parameter space and using integral instrumented fuel assessment cases to determine the impact of these models on the overall fuel performance. Suggestions and guidance for future improvements to this method are provided to ensure the model covers relevant parameter space and phenomena.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Modeling of fission and activation products in molten salt reactors and their potential impact on the radionuclide monitoring stations of the International Monitoring System

Molten Salt Reactors (MSRs) are one of six Generation IV reactor designs currently under development around the world. Because of the unique operating conditions of MSRs, which include molten fuel and the continuous removal of gaseous fission products during operation, work was performed to analyze the potential impact of emissions on the International Monitoring System (IMS) of the Comprehensive Nuclear-Test-Ban Treaty (CTBT). Simulations were performed to predict the production of IMS-relevant radionuclides in four MSR designs operating under two scenarios: (1) a sealed reactor with releases only during operational shutdown, and (2) continuous reprocessing or sparging of the fuel salt. From these production estimates the radioxenon and radioiodine signatures were extracted and compared to three current reactor designs (Pressurized Water Reactor (PWR), BWR, RBMK). In cases where continuous reprocessing of the fuel salt occurred, both the radioxenon and radioiodine signatures were nearly indistinguishable from a nuclear explosion. Estimates were also made of the potential emission rate of radioxenon for three reactor designs and it was found that MSRs have the potential to emit radioxenon isotopes at a rate of 10^15-8×10^16 Bq/d for 133Xe if no abatement is used. An assessment was made of activation products using a candidate fuel salt (FLiBe) mixed with corrosion products for the Thorium Molten Salt Reactor (TMSR-LF1).

Johnson, Christine M.↗

Small-Scale Mechanical Testing of UO{sub 2}

The mechanical properties of UO{sub 2} fuel are of great importance to the nuclear engineering community for modeling of fuel performance during operation and accident scenarios. Data on the deformation of single crystals at room and elevated temperature can help these efforts by informing multiscale models. Small-scale testing techniques like micro-cantilever bending and nano-indentation have the ability to measure mechanical properties at the right length scale for this, while allowing the observation of the deformation of the material. In our work we perform micro-cantilever testing of UO{sub 2} at room temperature and nano-indentation testing up to 500 deg. C, as well as in-situ TEM micro-cantilever testing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

First Generation Least Expensive Approach to Fission (FiGLEAF) Testing Results

Successful development of space fission systems will require an extensive program of affordable and realistic testing. In addition to tests related to design/development of the fission system, realistic testing of the actual flight unit must also be performed. Testing can be divided into two categories, non-nuclear tests and nuclear tests. Full power nuclear tests of space fission systems are expensive, time consuming, and of limited use, even in the best of programmatic environments. If the system is designed to operate within established radiation damage and fuel burn up limits while simultaneously being designed to allow close simulation of heat from fission using resistance heaters, high confidence in fission system performance and lifetime can be attained through a series of non-nuclear tests. Non-nuclear tests are affordable and timely, and the cause of component and system failures can be quickly and accurately identified. MSFC is leading a Safe Affordable Fission Engine (SAFE) test series whose ultimate goal is the demonstration of a 300 kW flight configuration system using non-nuclear testing. This test series is carried out in collaboration with other NASA centers, other government agencies, industry, and universities. The paper describes the SAFE test series, which includes test article descriptions, test results and conclusions, and future test plans.

VanDyke, Melissa↗

Space Fission Propulsion Testing and Development Progress

Successful development of space fission systems will require an extensive program of affordable and realistic testing. In addition to tests related to design/development of the fission system, realistic testing of the actual flight unit must also be performed. Testing can be divided into two categories, non-nuclear tests and nuclear tests. Full power nuclear tests of space fission systems we expensive, time consuming, and of limited use, even in the best of programmatic environments. If the system is designed to operate within established radiation damage and fuel burn up limits while simultaneously being designed to allow close simulation of heat from fission using resistance heaters, high confidence in fission system performance and lifetime can be attained through a series of non-nuclear tests. Non-nuclear tests are affordable and timely, and the cause of component and system failures can be quickly and accurately identified. MSFC is leading a Safe Affordable Fission Engine (SAFE) test series whose ultimate goal is the demonstration of a 300 kW flight configuration system using non-nuclear testing. This test series is carried out in collaboration with other NASA centers, other government agencies, industry, and universities. If SAFE-related nuclear tests are desired they will have a high probability of success and can be performed at existing nuclear facilities. The paper describes the SAFE non-nuclear test series, which includes test article descriptions, test results and conclusions, and future test plans.

VanDyke, Melissa↗