Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Molybdenum”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Tuning bandgap and energy stability of Organic-Inorganic halide perovskites through surface engineering

Organohalide perovskite with a variety of surface structures and morphologies have shown promising potential owing to the choice of the type of heterostructure dependent stability. We systematically investigate and discuss the impact of 2-dimensional molybdenum-disulphide (MoS 2 ), molybdenum-diselenide (MoSe 2 ), tungsten-disulphide (WS 2 ), tungsten-diselenide (WSe 2 ), boron-nitiride (BN) and graphene monolayers on bandgap and energy stability of organic–inorganic halide perovskites. We found that MAPbI 3 deposited on BN-ML shows room temperature stability (-25 meV ~ 300 K) with an optimal bandgap of ~ 1.68 eV. The calculated absorption coefficient also lies in the visible-light range with a maximum of 4.9 × 10 4 cm –1 achieved at 2.8 eV photon energy. Furthermore, on the basis of our calculations, we suggest that the encapsulation of an organic–inorganic halide perovskite monolayers by semiconducting monolayers potentially provides greater flexibility for tuning the energy stability and the bandgap.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Phase transformation mechanism in irradiation-induced superlattice formation

Atomic kinetic Monte Carlo simulations were used to model void superlattice formation under irradiation in molybdenum, driven by anisotropic diffusion of self-interstitial atoms. A change in the phase transformation mechanism from nucleation and growth to spinodal decomposition occurred with increasing dose rate, with both mechanisms leading to superlattice formation. Analysis of a rate-theory based analytical model showed that an observed change in the kinetics of vacancy accumulation, the appearance of a region of positive second derivative in the plot of average vacancy concentration versus time, was caused by the onset of spinodal instability. Further, the analytical model showed that for molybdenum and several other metals where void superlattice formation is commonly observed, the phase transformation likely occurs by nucleation and growth. However, nickel may offer the possibility of experimental observation of the transition between phase transformation mechanisms.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Not all platinum surfaces are the same: Effect of the support on fundamental properties of platinum adlayer and its implications for the activity toward hydrogen evolution reaction

The adsorption of atomic hydrogen on a platinum monolayer supported on orthorhombic Mo 2 C(100) surface has been investigated, considering different hydrogen surface coverages. Calculations have been performed using density functional theory with the Perdew-Burke-Ernzerhof exchange correlation functional and a D3 Van der Waals corrections. The theoretical insight has been gained into atomic hydrogen interaction with Pt monolayer, supported on both molybdenum and well-studied tungsten carbide, and considering hydrogen surface coverage. Fundamental properties of Pt adlayer depend on the support, affecting hydrogen evolution activity of the resulting systems. At low hydrogen coverage all systems, with the exception of Pt supported on the molybdenum-terminated Mo 2 C, adsorb H comparably to a pristine Pt(111) surface and their high activity for the hydrogen evolution reaction is predicted. Additionally, at higher coverages supported Pt monolayers interact with atomic hydrogen unlike the Pt(111), suggesting that the activity of the supported and unsupported platinum toward hydrogen evolution reaction have different origins. Furthermore, the position of the supported platinum monolayers on the volcano curve is a function of the surface coverage, more so than for extended metal surfaces. Therefore, hydrogen surface coverage is a key variable to understand the catalytic potential, approaching towards an improved model for screening of electrocatalytic systems.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Fusion welding of refractory metals and ZrB 2 -SiC-ZrC ceramics

Molybdenum and a molybdenum alloy were fusion welded to ZrB2-based ceramics to determine if the electrical and thermal properties of the metals and ceramics affected their weldability. Commercial ceramic powders were hot pressed, machined into coupons, and preheated to 1600 °C before joining the ceramics to commercial metals using plasma arc welding. Weldability varied as indicated by the range of porosity observed within the fusion zones. Measured thermal and electrical properties appeared to have little to no effect on the weldability of metal-ceramic welds despite the large range of values measured across each property. Differences in melting temperatures between metal and ceramic coupons did affect weldability by changing the weld penetration depth into ceramic coupons. Finally, future studies on metal-ceramic welds are suggested to investigate the effect that work function, melt viscosity, wetting, or other properties have on weldability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

A critical review of the history of fabricating monolithic U-Mo fuel plates

The fabrication of monolithic uranium-molybdenum alloy fuels, specifically those developed for high-performance research and test reactors, began in the early 2000s. The primary fuel form consists of uranium alloyed with 10-wt% molybdenum in a thin foil coated with zirconium and encapsulated in aluminum-6061 cladding. Over the years, the process has evolved with different types of casting, heat treatments, rolling schedules, and cladding applications. This review examines the history of these fabrication processes and their impact on microstructure and fuel-swelling performance. Even though various fabrication methods were used, we found little correlation between fabrication variation and fuel swelling. This insensitive relationship between fabrication variation and fuel swelling is primarily due to inhomogeneous microstructures that formed during casting and grain refinement that occurred during rolling. We conclude that the fabrication processes we examined produced similar microstructures, indicating that the fuel microstructure is somewhat insensitive to the fabrication parameters evaluated. However, the relatively small amount of historic data, such as those for grain sizes, limited this analysis. More recently fabricated materials, such as those from ongoing irradiation experiment, Mini-Plate-1 and Mini-Plate-2, were also excluded from this analysis and are intended to be reviewed separately. The findings, that fuel microstructure is somewhat insensitive to the fabrication parameters, do not imply that any fabrication method is acceptable, given the uncertainties in data and fuel-swelling observations. For example, only arc melting and vacuum induction melting casting processes were previously explored in the historic fabrication efforts. In conclusion, the findings should not be extrapolated to other casting processes.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Minimizing thickness variation in monolithic U-10Mo fuel foil and Zr interlayer during hot rolling: A microstructure-based finite element method analysis

Low-enriched uranium alloyed with 10 wt. % molybdenum (U-10Mo) has been identified as a promising alternative to highly enriched uranium fuel for the United States’ high performance research reactors. The monolithic U-10Mo fuel plate consists of a metallic U-10Mo fuel foil with a 25 µm Zr interlayer and a relatively thick cladding of aluminum alloy 6061. The Zr interlayer is typically applied during the hot co-rolling process, and this process dictates the uniformity of the Zr interlayer. Thickness variation observed in the U-10Mo and Zr interlayer has been attributed to several sources: the initial grain size of the U-10Mo castings, can materials, rolling temperature, inhomogeneous molybdenum content, and porosity in the cast U-10Mo. This thickness variation limits the ability to meet the dimensional specification; thus, a better understanding of the factors causing the nonuniform thickness is needed. In this work, we used a novel, microstructure-based finite element method to model the hot rolling process to address these concerns. Grain microstructures in U-10Mo were tessellated and explicitly considered in the finite element model. Each grain was assigned a random material property to mimic the grain strength variations induced by different grain orientations. Simulations were performed using six steel can thicknesses, four grain sizes, and with or without a Zr interlayer to investigate the influences of those variables on the thickness nonuniformity. The simulation results showed that a thinner steel can and finer U-10Mo grain size reduce thickness variations in both the U-10Mo fuel foil and Zr interlayer. The direct findings from the simulations and analysis can be used to optimize the hot rolling schedule, reduce fabrication defects, and meet the dimensional specifications. The proposed microstructure-based finite element model can be also coupled with experimental microstructure characterization data, images, and models to simulate multi-pass hot rolling.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Exploration of Sn 70 Li 30 alloy as possible material for flowing liquid metal plasma facing components

As an advanced alternative to solid materials, Liquid Metals (LM) may offer more resilient and feasible Plasma Facing Components (PFCs). Particularly, regarding the unavoidable material erosion/degradation produced by particle/heat fluxes in future fusion devices where much longer duty cycles are expected. Furthermore, configurations that propose a flowing LM surface can add the advantage of a continuously fresh and clean layer facing the plasma. Although lithium is the most widely tested option, tin-lithium (SnLi) alloys have been proposed to attempt to combine the positive characteristics of both pure elements and ameliorate the specific issues of lithium. In this work, the potential use of Sn70Li30 alloy in such flowing concepts has been explored by addressing several preliminary and mandatory aspects for its utilization. Key issues such as wettability and compatibility of the alloy with relevant substrates have been studied in a multidisciplinary approach. The data obtained from deposited liquid tin-lithium droplets indicates approximate wetting temperatures of 360 °C, 390 °C and 405 °C for the fresh alloy on 316 stainless steel, molybdenum, and tungsten, respectively. However, the alloy contamination appeared to strongly affect the wetting characteristics of materials, increasing their wetting temperature by ~130 °C in the worst observed cases. Interestingly, in some instances, the instability of the liquid alloy surface was observed in the form of sudden gaseous ejection. The deposited droplets were posteriorly characterized in terms of absolute composition and depth profile by Inductively Coupled PlasmaOptical Emission Spectroscopy (ICP-OES) and Secondary Ion Mass Spectrometry (SIMS-ToF). Additionally, the nature and composition of the boundaries between the substrates and alloy microparticles was investigated by Scanning Electron Microscopy (SEM), Energy Dispersive X-Ray Spectroscopy (EDS), and 3D Laser microscopy. The overall results of this post-mortem characterization revealed that first signs of corrosion induced by both alloy elements (lithium-chromium association and iron-tin intermetallic mixing) were present on 316 stainless steel after short exposures (≤3 h) at temperatures lower than 550 °C. Conversely, molybdenum and tungsten showed good compatibility with the alloy in equivalent conditions. The global implications of these results are finally addressed, focusing on the future perspectives and the more viable scenarios for the eventual utilization of these alloys in flowing liquid metal configurations.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Effects of Casting Parameters and Impurity Concentrations on As-Cast U–10Mo

This work investigates the effects of casting parameter changes on as-cast uranium-10 wt% molybdenum alloys on a 1-2kg scale. A commercial tilt-pour vacuum induction melting system was utilized to study the effects of casting atmosphere, total heating time, hold time at maximum temperature, mold temperature, and crucible type on the as-cast microstructure of U-10Mo. Ten thin plates (5.08 mm thick) and four thick plates (25.4 mm and 63.5 mm thick) were cast and analyzed for carbon, oxygen, hydrogen, and nitrogen impurities. Additionally, molybdenum content and primary dendrite length (PDL) of the microstructure was quantified. A statistical evaluation was performed to identify key carbon and oxygen relationships with operating parameters, impurities, and primary dendrite length. Additional factors investigated include: crucible material, time at maximum temperature, total heating time, and pour temperature. Zirconia crucibles reduced carbon content on average by 35%. Additionally, there was a significant statistical association between carbon and oxygen content, between oxygen content and maximum temperature hold time, between mold temperature and PDL, and between PDL, maximum temperature hold time and mold temperature.

Huber, Zachary F.↗
DOE OSTI2026

Demonstration of an All-Refractory Corrosion-Resistant Molten Salt Pumping and Storage Infrastructure Up to 950 degrees C

Concentrating solar power (CSP) with thermal energy storage (TES) has an estimated cost similar to solar photovoltaics (PV) with lithium-ion batteries (LIB), but CSP + TES has the potential for significantly reduced cost by operating above 700 degrees C. However, this requires a TES medium and containment infrastructure which are chemically compatible and do not degrade above 700 degrees C. MgCl2-KCl-NaCl (MKN) salt is a promising medium, but when MKN salt has small amounts of water and oxygen dissolved in it, it excessively corrodes conventional commercial alloys. Here, we consider refractory materials including graphite, carbon-carbon composite (C/C), and molybdenum because they maintain high mechanical strength at elevated temperatures and are expected to resist corrosion by MKN salt. While selection of refractory materials is often constrained by the need to remain chemically stable in air, this work uses an enclosure filled with inert gas to allow the use of materials like graphite and molybdenum. Notably, graphite components can seal against liquids unlike many brittle refractory materials. We demonstrate a centrifugal pump and mechanical seals made of refractory materials in a laboratory-scale circulation loop, which successfully operated continuously for more than 49 h at temperatures ranging from 750 degrees C to 950 degrees C with no mechanical failures or chemical degradation of the refractory materials. To the best of our knowledge, this is the highest temperature molten salt circulation loop that has been successfully developed, and this refractory infrastructure allows for operation at even much higher temperatures (<1600 degrees C) if a storage medium with a lower vapor pressure is used. The principles of this architecture are relevant to other applications with high temperature flowing metals and salts including Generation IV nuclear fission reactors for power production and molten salt electrolysis reactors for metallurgical processing.

14 SOLAR ENERGY↗
DOE OSTI2021

Prediction of Solution Behavior via Calorimetric Measurements Allows for Detailed Elucidation of Polyoxometalate Transformation

The solution behavior of a polyoxometalate cluster, LiNa-U 24 Pp 12 (Li 24 Na 24 [(UO 2 O 2 ) 24 (P 2 O 7 ) 12 ]) that consists of 24 uranyl ions, peroxide groups, and 12 pyrophosphate linkers, was successfully predicted based on new thermodynamic results using a calorimetric method recently described for uranyl peroxide nanoclusters (UPCs), molybdenum blues, and molybdenum browns. The breakdown of LiNa-U 24 Pp 12 and formation of U 24 (Li 24 [UO 2 O 2 OH] 24 ) was monitored in situ via Raman spectroscopy using a custom heating apparatus. A combination of analytical techniques confirmed the simultaneous existence of U 24 Pp 12 and U 24 midway through the conversion process and U 24 as the single end product. The application of a molecular weight filter resulted in a complete and successful separation of UPCs from solution and, in conjunction with DOSY results, confirmed the presence of large intermediate cluster building blocks.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Probing the Framework Metal Dependent Properties of Actinide-Centered Polyoxoalkoxide Sandwich-Type Complexes

Development of a simple and scalable synthesis of (TBA) 3 [W 5 O 18 MoNO] provides for the formation of the mixed-metal lacunary polyoxoalkoxide, (TBA) 2 [W 4 O 13 (OMe) 4 MoNO][Na(MeOH)]. This complex was used to synthesize a series of polyoxoalkoxide sandwich-type complexes with the general formula (TBA) 2 [M{W 4 O 13 (OMe) 4 MoNO} 2 ], where M = Zr(IV), Hf(IV), Th(IV), U(IV), and Np(IV). Compared to the analogous all-molybdenum complexes, the series have drastically different optical and redox properties. The results indicate that framework metal substitution acts as a tool for “orbital engineering”, with Density Functional Theory (DFT) calculations revealing that the major consequence of incorporation of tungsten into the complexes is localization of LUMO and LUMO+1 on the molybdenum centers remaining in the molecule. The change in the distribution of the frontier orbitals translates to discrepancies in the electronic properties of the series. Given the rarity of polyoxometalate complexes featuring a U(V) ion, one electron oxidation of (TBA) 2 [U(IV){W 4 O 13 (OMe) 4 MoNO} 2 ] was pursued. Isolation of the corresponding U(V) centered sandwich-type complex is reported, only the second example of U(V)-polyoxometalate complex described to date.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Surfactant-Mediated Growth and Patterning of Atomically Thin Transition Metal Dichalcogenides

The role of additives in facilitating the growth of conventional semiconducting thin films is well-established. Apparently, their presence is also decisive in the growth of two-dimensional transition metal dichalcogenides (TMDs), yet their role remains ambiguous. In this work, we show that the use of sodium bromide enables synthesis of TMD monolayers via a surfactant-mediated growth mechanism, without introducing liquefaction of metal oxide precursors. We discovered that sodium ions provided by sodium bromide chemically passivate edges of growing molybdenum disulfide crystals, relaxing in-plane strains to suppress 3D islanding and promote monolayer growth. To exploit this growth model, molybdenum disulfide monolayers were directly grown into desired patterns using predeposited sodium bromide as a removable template. In conclusion, the surfactant-mediated growth not only extends the families of metal oxide precursors but also offers a way for lithography-free patterning of TMD monolayers on various surfaces to facilitate fabrication of atomically thin electronic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

One-Step Transfer of Symmetric and Asymmetric Contacts for Large-Scale 2D Electronics and Optoelectronics

Two-dimensional (2D) semiconductors are highly promising candidates for thin-film transistor applications due to their scalability, transferability, atomic thickness, and relatively high carrier mobility. However, a substantial performance gap remains between individual devices based on single-crystalline 2D films and wafer-scale integrated circuits, primarily due to defects introduced during conventional fabrication processes. Here, we report a diamond-assisted electrode transfer technique for the van der Waals integration of wafer-scale prefabricated electrode arrays onto 2D materials, enabling scalable electronics and optoelectronics. Implemented on metal–organic chemical vapor deposition-grown monolayer molybdenum disulfide, this method forms ultraclean metal–semiconductor interfaces, yielding field-effect transistors with excellent ohmic contacts, a low contact resistance of 400 Ω·μm, and a Schottky barrier height of only 9 meV. Furthermore, we demonstrate a scalable transistor array on monolayer molybdenum disulfide with excellent device performance uniformity, achieving an average field-effect mobility of 30 cm 2 V –1 s –1 and an on/off current ratio exceeding 105. Additionally, high photocurrent and responsivity were demonstrated in the array devices, showing their potential for excellent image detection. We further demonstrate the versatility of this technique by fabricating a Schottky diode array through a single-step transfer of asymmetric electrodes─low work function aluminum and high work function gold─onto monolayer tungsten diselenide. This approach provides a clean, effective solution for contact engineering in 2D materials, offering a viable pathway toward wafer-scale, high-performance 2D electronics, optoelectronics, and integrated circuits.

2D electronics↗
DOE OSTI2022

DFT Investigation of Ammonia Formation via a Langmuir–Hinshelwood Mechanism on Mo-Terminated δ-MoN(0001)

In this work, we employed density functional theory to elucidate the energetics associated with elementary steps along a Langmuir-Hinshelwood mechanism for the Haber-Bosch synthesis of ammonia from N 2 and H 2 on a hexagonal, Mo-terminated molybdenum nitride surface. Using nudged elastic band calculations, we determined the energy barriers involved in the reaction processes. An active site consisting of four nearest-neighbor Mo atoms, previously identified as an active site on similar surfaces, was chosen to investigate the reaction processes. Using this approach, we calculate a barrier of ~0.5 eV for the dissociation of N 2 . The superior activity of the dissociation of the strong N 2 bonds is rationalized based on the unique geometric and electronic configurations present at these active sites. Despite the favorable energetics for nitrogen dissociation, the energy cost for hydrogenation of NH x (0 ≤ x ≤ 2) species is shown to be energetically limiting for the formation of ammonia through the Langmuir-Hinshelwood mechanism at these sites, with elementary step activation barriers calculated to be as large as ~2 eV. A comparison to Haber-Bosch results derived from a similar γ-Mo 2 N model system suggests the relative independence of surface chemistry and bulk stoichiometry for rhombic Mo 4 active sites present on molybdenum nitrides.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Phase controlled synthesis of transition metal carbide nanocrystals by ultrafast flash Joule heating

Nanoscale carbides enhance ultra-strong ceramics and show activity as high-performance catalysts. Traditional lengthy carburization methods for carbide syntheses usually result in coked surface, large particle size, and uncontrolled phase. Here, a flash Joule heating process is developed for ultrafast synthesis of carbide nanocrystals within 1 s. Various interstitial transition metal carbides (TiC, ZrC, HfC, VC, NbC, TaC, Cr 2 C 3 , MoC, and W 2 C) and covalent carbides (B 4 C and SiC) are produced using low-cost precursors. By controlling pulse voltages, phase-pure molybdenum carbides including β-Mo 2 C and metastable α-MoC 1-x and η-MoC 1-x are selectively synthesized, demonstrating the excellent phase engineering ability of the flash Joule heating by broadly tunable energy input that can exceed 3000 K coupled with kinetically controlled ultrafast cooling (>10 4 K s –1 ). Theoretical calculation reveals carbon vacancies as the driving factor for topotactic transition of carbide phases. The phase-dependent hydrogen evolution capability of molybdenum carbides is investigated with β-Mo 2 C showing the best performance.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2024

Direct conversion of methane to aromatics and hydrogen via a heterogeneous trimetallic synergistic catalyst

Abstract Non-oxidative methane dehydro-aromatization reaction can co-produce hydrogen and benzene effectively on a molybdenum-zeolite based thermochemical catalyst, which is a very promising approach for natural-gas upgrading. However, the low methane conversion and aromatics selectivity and weak durability restrain the realistic application for industry. Here, a mechanism for enhancing catalysis activity on methane activation and carbon-carbon bond coupling has been found to promote conversion and selectivity simultaneously by adding platinum–bismuth alloy cluster to form a trimetallic catalyst on zeolite (Pt-Bi/Mo/ZSM-5). This bimetallic alloy cluster has synergistic interaction with molybdenum: the formed CH 3 * from Mo 2 C on the external surface of zeolite can efficiently move on for C-C coupling on the surface of Pt-Bi particle to produce C 2 compounds, which are the key intermediates of oligomerization. This pathway is parallel with the catalysis on Mo inside the cage. This catalyst demonstrated 18.7% methane conversion and 69.4% benzene selectivity at 710 °C. With 95% methane/5% nitrogen feedstock, it exhibited robust stability with slow deactivation rate of 9.3% after 2 h and instant recovery of 98.6% activity after regeneration in hydrogen. The enhanced catalytic activity is strongly associated with synergistic interaction with Mo and ligand effects of alloys by extensive mechanism studies and DFT calculation.

03 NATURAL GAS↗
DOE OSTI2021

Tracing the incorporation of the “ninth sulfur” into the nitrogenase cofactor precursor with selenite and tellurite

We report Molybdenum nitrogenase catalyses the reduction of N 2 to NH 3 at its cofactor, an [(R-homocitrate)MoFe 7 S 9 C] cluster synthesized via the formation of a [Fe 8 S 9 C] L-cluster prior to the insertion of molybdenum and homocitrate. We have previously identified a [Fe 8 S 8 C] L*-cluster, which is homologous to the core structure of the L-cluster but lacks the ‘ninth sulfur’ in the belt region. However, direct evidence and mechanistic details of the L*- to L-cluster conversion upon ‘ninth sulfur’ insertion remain elusive. Here we trace the ‘ninth sulfur’ insertion using SeO 3 2- and TeO 3 2- as ‘labelled’ SO 3 2- . Biochemical, electron paramagnetic resonance and X-ray absorption spectroscopy/extended X-ray absorption fine structure studies suggest a role of the ‘ninth sulfur’ in cluster transfer during cofactor biosynthesis while revealing the incorporation of Se 2- - and Te 2- -like species into the L-cluster. Density functional theory calculations further point to a plausible mechanism involving in situ reduction of SO 3 2- to S 2- , thereby suggesting the utility of this reaction to label the catalytically important belt region for mechanistic investigations of nitrogenase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

High-pressure strengthening in ultrafine-grained metals

The Hall–Petch relationship, according to which the strength of a metal increases as the grain size decreases, has been reported to break down at a critical grain size of around 10 to 15 nanometres. As the grain size decreases beyond this point, the dominant mechanism of deformation switches from a dislocation-mediated process to grain boundary sliding, leading to material softening. In one previous approach, stabilization of grain boundaries through relaxation and molybdenum segregation was used to prevent this softening effect in nickel–molybdenum alloys with grain sizes below 10 nanometres. Here we track in situ the yield stress and deformation texturing of pure nickel samples of various average grain sizes using a diamond anvil cell coupled with radial X-ray diffraction. Our high-pressure experiments reveal continuous strengthening in samples with grain sizes from 200 nanometres down to 3 nanometres, with the strengthening enhanced (rather than reduced) at grain sizes smaller than 20 nanometres. Here, we achieve a yield strength of approximately 4.2 gigapascals in our 3-nanometre-grain-size samples, ten times stronger than that of a commercial nickel material. A maximum flow stress of 10.2 gigapascals is obtained in nickel of grain size 3 nanometres for the pressure range studied here. We see similar patterns of compression strengthening in gold and palladium samples down to the smallest grain sizes. Simulations and transmission electron microscopy reveal that the high strength observed in nickel of grain size 3 nanometres is caused by the superposition of strengthening mechanisms: both partial and full dislocation hardening plus suppression of grain boundary plasticity. These insights contribute the ongoing search for ultrastrong metals via materials engineering.

36 MATERIALS SCIENCE↗