Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MAGNESIUM COMPOUND”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Coincidence site lattice boundary mechanism for the preferred growth of Goss and Cube grains during annealing in an Al-Cu-Mg alloy

Highlights: • Both Goss and Cube grains are recrystallized out of Brass matrix. • Boundary character between Brass and Goss grains was Σ9, and that between Brass and Cube was Σ5. • Σ9 and Σ5 boundaries only transitionally appeared during recrystallization. • Temperature had decisive effect on the formation and mobility of CSL boundaries. • Σ9 and Σ5 boundaries with high index planes were highly mobile. - Abstract: The formation mechanism of recrystallized textures in an Al-Cu-Mg alloy was investigated by means of three dimensional orientation distribution functions (ODFs) and in-situ electron back-scattered diffraction (EBSD). The results showed that in the hot-rolled alloy with a very sharp Brass texture but weak Copper and S orientations, both Goss and Cube grains were recrystallized out of parent Brass matrix. In-situ EBSD analysis revealed that characteristic boundary between Brass and Goss grains to be Σ9, while that between Brass and Cube grains to be Σ5. Frequency of Σ9 and Σ5 boundaries increased quickly at early stage and then reduced gradually with the process of recrystallization. Annealing at a higher temperature (320 °C) was found to be beneficial for the formation of Σ9 boundary, while at lower one (300 °C), Σ5 boundary became dominant. Besides, with temperature decreasing from 320 to 300 °C, the mobility of Σ9 boundaries was greatly degraded, but relatively, Σ5 boundaries still behaved highly mobile. Principally, the preferred growth of recrystallized Goss and Cube grains was respectively attributed to the high mobility of Σ9 and Σ5 boundaries with high index planes that the square sum of plane index was larger than 3.

36 MATERIALS SCIENCE↗

Dependence of microwave dielectric properties on crystallization behaviour of CaMgSi{sub 2}O{sub 6} glass-ceramics

The effects of the crystallization behaviour of CaMgSi{sub 2}O{sub 6} (diopside) glass-ceramics on their microwave dielectric properties were investigated as functions of the Cr{sub 2}O{sub 3} content and heat-treatment method used (one or two steps). The crystallization behaviours of the specimens were affected by the Cr{sub 2}O{sub 3} content as well as by the heat-treatment method employed, and were evaluated using X-ray diffraction and the combined Rietveld and reference intensity ratio (RIR) method. The dielectric constants (K) of the specimens did not change significantly with an increase in the Cr{sub 2}O{sub 3} content. The quality factor (Qf) of the specimens increased for Cr{sub 2}O{sub 3} contents of up to 0.5 wt% Cr{sub 2}O{sub 3}, but then decreased for higher contents. These results could be attributed to the degree of crystallization. For the same Cr{sub 2}O{sub 3} content, the specimens that underwent a two-step heat treatment showed lower K values and higher Qf values than those heat-treated in one-step. These results could be attributed to the smaller crystallite size and higher degree of crystallization in the specimens obtained from the two-step heat treatment compared with those of the specimens heat-treated in one-step method.

36 MATERIALS SCIENCE↗

Photoluminescence and cathodoluminescence properties of Eu{sup 3+} ions activated AMoO{sub 4} (A = Mg, Ca, Sr, Ba) phosphors

Highlights: • Under 393 nm excitation, strong red emission located at 615 nm was observed in all the samples. • The Eu{sup 3+}-activated CaMoO{sub 4} phosphor exhibited the strongest PL properties. • The CIE chromaticity coordinate of Eu{sup 3+}-activated CaMoO{sub 4} phosphor was (0.647,0.352). • The color purity of Eu{sup 3+}-activated CaMoO{sub 4} phosphor was 92.8%. • Strong CL properties were observed in the Eu{sup 3+}-activated CaMoO{sub 4} phosphor. - Abstract: Eu{sup 3+}-activated AMoO{sub 4} (A = Mg, Ca, Sr, Ba) phosphors were synthesized by a solid-state reaction method. Photoluminescence and cathodoluminescence (CL) spectra as well as X-ray diffraction patterns were measured to characterize the fabricated samples. Under 393 nm excitation, strong red emissions located at ∼615 nm corresponding to the {sup 5}D{sub 0} → {sup 7}F{sub 2} transition of Eu{sup 3+} ions were observed in all the samples. Compared with other Eu{sup 3+} ions activated AMoO{sub 4} (A = Mg, Sr, Ba) phosphors, Eu{sup 3+}-activated CaMoO{sub 4} phosphor exhibited the strongest red emission intensity with better Commission Internationale de L’Eclairage chromaticity coordinate and higher color purity. Furthermore, the CL results indicated that the Eu{sup 3+}-activated CaMoO{sub 4} phosphor had excellent luminescence properties.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Auto-combustion synthesis and characterization of Mg doped CuAlO{sub 2} nanoparticles

The synthesis of pure and Mg doped Copper aluminumoxide CuAlO{sub 2}nanoparticles, a promising p-type TCO (transparent conducting oxide) have been done bysol gel auto combustion method using NaOH as a fuel, calcinated at 600°C. The structural properties were examined by XRD and SEM techniques. The optical absorption spectra of CuAlO{sub 2} sample recorded by UV-VIS spectrophotometer in the range of 200 to 800 nm have been presented. The crystallite size was determined by powder X-ray diffraction technique. The electrical behavior of pure and Mg doped CuAlO{sub 2} has been studied over a wide range of frequencies by using complex impedance spectroscopy.The variation of a.c. conductivity has been studied as function of frequency and temperature. The data taken together conclude that doping causes decreases in the ac conductivity of the nanoparticles as compared with the pure nanoparticles. Mg doping affects the optical properties and band gap.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Effect of Sm-Rich Phase on Corrosion Behavior of Hot-Extruded AZ31-1.5Sm Magnesium Alloy

The effects of Sm on the corrosion and microstructure behavior of hot-extruded AZ31 magnesium alloy were investigated by SEM, TEM, weight loss analysis, and electrochemical measurements. The results indicated that granular Al{sub 2}Sm phase ~ 4 μm in size in the hot-extruded AZ31 magnesium alloy modified with 1.5 wt.% Sm leads to significant grain refinement. The corrosion rate decreased from 15.98 × 10{sup −4} to 11.19 × 10{sup −4} g cm{sup −2} h{sup −1} in the transverse section and from 8.57 × 10{sup −4} to 6.20 × 10{sup −4} g cm{sup −2} h{sup −1} in the longitudinal section. Compared to the unmodified alloy, the corrosion potential of the Sm-modified alloy in the transverse and longitudinal sections increased by 98 and 62 mV, respectively, and the R{sub ct} value (charge transfer resistance) in the transverse and longitudinal sections of the modified alloy increased from 1764 and 1756 to 2928 and 2408 Ω cm{sup 2}, respectively. The results showed that the corrosion resistance of hot-extruded AZ31 magnesium alloy was significantly improved by Sm addition due to the grain refinement, the decreased dislocation density, and the suppression of micro-galvanic corrosion caused by Al-Sm-(Mn) intermetallic compounds.

36 MATERIALS SCIENCE↗

Texture Effect on Fatigue Crack Propagation Behavior in Annealed Sheets of an Al-Cu-Mg Alloy

The effects of texture, including Brass, Goss + Cube and Cube, on the fatigue crack growth behavior in annealed Al-Cu–Mg alloy sheets were characterized in this investigation. Results showed that the Goss + Cube sheet possessed the greatest fatigue threshold value and the lowest fatigue crack propagation (FCP) rate, and the Brass sheet presented the smallest threshold value and the greatest FCP rate among the three textured sheets. SEM results showed more slip bands and more tortuous crack path formed in Goss + Cube sheet during cyclic loading, and EBSD results showed that numerous dramatic crack deflections occurred when fatigue crack propagated across Goss-grain boundary in Goss + Cube sheet, indicating that the grain orientations including Goss and Cube had positive effect on enhancing the FCP resistance. On the one hand, Goss and Cube grains have more high Schmid factor slip systems than Brass grain, promoting persistent slip bands formation and externally applied energy consumption, consequently giving rise to a high resistance to FCP. On the other hand, Goss grains could induce crack deflection with large twist angles, resulting in more energy consumption during the cracking process and thereby enhance the FCP resistance.

36 MATERIALS SCIENCE↗

Microstructural Characterization and Electrochemical Behavior of AA2014 Al-Cu-Mg-Si Alloy of Various Tempers

AA2014 Al-Cu-Mg-Si alloy is subjected to aging heat treatment, and microstructural features and electrochemical behavior of the AA2014 Al-Cu-Mg-Si alloy of various tempers have been characterized. Hardness measurement of the alloy of different tempers showed typical age hardening behavior. X-ray diffraction and transmission electron microscopy studies revealed the presence of characteristic phases. Differential scanning calorimetry study displayed the sequence of solid-state precipitation and dissolution reactions in the AA2014 alloy of various tempers. Electrochemical behavior was assessed by measurement of variation of open-circuit voltage with time, potentiodynamic polarization and potentiodynamic cyclic polarization of the AA2014 alloy of various tempers in 3.5 wt.% NaCl solution at near neural (pH ~ 7) and at alkaline (pH 12) conditions. Potentiodynamic polarization studies of different tempers in 3.5 wt.% NaCl solution at pH ~ 7 showed that the corrosion potential (E{sub corr}) value has shifted toward more negative (active) direction with increasing aging time. The cyclic polarization in 3.5 wt.% NaCl solution at pH ~ 7 displayed active–passive behavior and also showed a large hysteresis loop indicating high pit growth damage.

36 MATERIALS SCIENCE↗

Crystal and electronic structures, luminescence properties of Eu{sup 2+}-doped Si{sub 6-z}Al{sub z}O{sub z}N{sub 8-z} and M{sub y}Si{sub 6-z}Al{sub z-y}O{sub z+y}N{sub 8-z-y} (M=2Li, Mg, Ca, Sr, Ba)

The crystal structure, electronic structure, and photoluminescence properties of Eu{sub x}Si{sub 6-z}Al{sub z-x}O{sub z+x}N{sub 8-z-x} (x=0-0.1, 0<z<1) and Eu{sub x}M{sub y}Si{sub 6-z}Al{sub z-x-y}O{sub z+x+y}N{sub 8-z-x-y} (M=2Li, Mg, Ca, Sr, Ba) have been studied. Single-phase Eu{sub x}Si{sub 6-z}Al{sub z-x}O{sub z+x}N{sub 8-z-x} can be obtained in very narrow ranges of x{<=}0.06 (z=0.15) and z<0.5 (x=0.3), indicating that limited Eu{sup 2+} ions can be incorporated into nitrogen-rich Si{sub 6-z}Al{sub z}O{sub z}N{sub 8-z}. The Eu{sup 2+} ion is found to occupy the 2b site in a hexagonal unit cell (P6{sub 3}/m) and directly connected by six adjacent nitrogen/oxygen atoms ranging 2.4850-2.5089 A. The calculated host band gaps by the relativistic DV-X{alpha} method are about 5.55 and 5.45 eV (without Eu{sup 2+} 4f5d levels) for x=0 and 0.013 in Eu{sub x}Si{sub 6-z}Al{sub z-x}O{sub z+x}N{sub 8-z-x} (z=0.15), in which the top of the 5d orbitals overlap with the Si-3s3p and N-2p orbitals within the bottom of the conduction band of the host. Eu{sub x}Si{sub 6-z}Al{sub z-x}O{sub z+x}N{sub 8-z-x} shows a strong green emission with a broad Eu{sup 2+} band centered at about 530 nm under UV to near-UV excitation range. The excitation and emission spectra are hardly modified by Eu concentration and dual-doping ions of Li and other alkaline-earth ions with Eu. Higher Eu concentrations can significantly quench the luminescence of Eu{sup 2+} and decrease the thermal quenching temperature. In addition, the emission spectrum can only be slightly tuned to the longer wavelengths ({approx}529-545 nm) by increasing z within the solid solution range of z<0.5. Furthermore, the luminescence intensity of Eu{sub x}Si{sub 6-z}Al{sub z-x}O{sub z+x}N{sub 8-z-x} can be improved by increasing z and the dual-doping of Li and Ba. - Graphical abstract: Excitation and emission spectra of Eu{sub x}Si{sub 6-z}Al{sub z-x}O{sub z+x}N{sub 8-z-x} with the project of a 2x2x2 supercell crystal structure viewed along (001), in which red spheres are the Eu atoms.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructural, mechanical and electrochemical behaviour of a 7017 Al–Zn–Mg alloy of different tempers

The aim of the investigation is to assess the microstructural features and associated physical, mechanical and electrochemical properties of a 7017 Al–Zn–Mg alloy of various tempers. A 7017 Al–Zn–Mg alloy was subjected to different ageing schedules to produce under-(T4), peak-(T6), over-(T7) and highly over-aged tempers. Optical microscopy, hardness measurement, electrical conductivity measurement, tensile testing and SEM fractographs, differential scanning calorimetry (DSC), transmission electron microscopy (TEM), and electrochemical polarization studies have been used to characterize the alloy tempers. Hardness measurement and tensile testing showed the characteristic age hardening phenomenon of aluminium alloys. Optical and TEM micrographs have revealed the variation in size of matrix strengthening η′ (MgZn{sub 2}) and also the size and distribution of grain boundary η (MgZn{sub 2}) precipitate with ageing time. DSC thermograms exhibiting exothermic and endothermic peaks indicated the characteristic solid state reaction sequence of the 7017 alloy. Potentiodynamic polarization study of the 7017 alloy of various tempers in 3.5 wt.% NaCl solution at near neutral pH showed typical active metal dissolution behaviour, but at pH 12 an active–passive–transpassive transition behaviour has been observed. - Graphical abstract: TEM micrograph of the 7017 aluminium alloy of various tempers (a, b) under aged (T4), (c, d) peak aged (T6), (e, f) over aged (T7) and (g, h) highly over-aged. Display Omitted - Highlights: • 7017 Al-Zn-Mg alloy was subjected to different artificial ageing treatments. • Characterization of 7017 alloy tempers by hardness, tensile, DSC, TEM and electrochemical behaviour. • Structure-properties relationship of the 7017 Al-Zn-Mg alloy of various tempers.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mechanical behavior and texture development of over-aged and solution treated Al-Cu-Mg alloy during multi-directional forging

The effects of initial heat treatments, i.e. solution treating and over ageing, on deformation behavior of an age hardenable Al-Cu-Mg alloy, including mechanical properties and texture evolution, during multi-directional forging (MDF) are investigated. Hardness measurements, electron back scatter diffraction (EBSD) maps, and differential scanning calorimetry (DSC) are carried out. Mechanical behaviors of the alloy in terms of compressive stress and hardness test after MDF are investigated. In both solution treated and over-aged alloys, the compressive stress during MDF shows an increase up to the second pass, and by further straining the flow stress is decreased. However, shear and deformation bands are formed in both solution treated and over-aged alloys, the density of these instabilities in the solution treated alloy is higher than that in over-aged alloy. In the solution treated alloy, not only large particles induce deformation bands, but also the dynamically formed GPB zones/Cu-Mg co-clusters. Texture analysis shows that the shear component of C {001}<110> (Φ{sub 1} = 90°, Φ = 0°, Φ{sub 2} = 45°) is developed with 18 mrd during MDF of the over-aged alloy. In the solution treated alloy, due to the high density of deformation bands and different microchemistry of the matrix in comparison with that of the over-aged alloy, the Copper type texture component {112}<111> (Φ{sub 1} = 90°, Φ = 35°, Φ{sub 2} = 45°) is developed with 11 mrd.

36 MATERIALS SCIENCE↗

Effect of heat treatment variables on the formation of precipitate free zones (PFZs) in Mg-8Al-0.5Zn alloy

Highlights: • The effect of heat treatment variables on the development of PFZs in the AZ80 Mg alloy has been systematically examined. • PFZ width is found to be strongly dependant on aging temperature as compared to aging time. • The PFZ width in the AZ80 alloy is found to be weakly dependant on the solution temperature and quenching rate. • The solute depletion is found to be the dominant factor in explaining the evolution of PFZ width. - Abstract: The present study is focussed on investigating the effect of heat treatment variables on the formation of precipitate free zones (PFZs) in the AZ80 Mg alloy. The effect of solutionizing temperature, quenching media, aging temperature and time on the PFZ development has been systematically examined. Scanning electron microscopy and nanoindentation were employed to characterize the PFZ regions. Electron probe micro analysis (EPMA) was used to examine the role of solute depletion in the formation of these zones. Moreover, the estimation of vacancy concentration profiles near the grain boundary was used to investigate the role of vacancy depletion. The solute depletion is found to be the dominant mechanism in the development of PFZ regions as compared to vacancy.

36 MATERIALS SCIENCE↗

Characterization of hot extrusion and heat treatment on mechanical properties in a spray formed ultra-high strength Al-Zn-Mg-Cu alloy

Highlights: • The spray forming technology was used to fabricate ultra-high strength aluminum alloy. • The alloy under RRA state obtained the highest ultimate tensile strength of 732 MPa. • The effects of dislocations, solutes and precipitates etc., on yield strength were calculated. • Precipitation was characterized as the main strengthening mechanism for aging states. - Abstract: To obtain the optimal mechanical properties, several processes including spray forming technology, two passes hot extrusion and substantial heating treatments were operated on an Al-Zn-Mg-Cu-Zr alloy. The characterization methods used in this study include tensile tests, X-ray diffraction, differential scanning calorimetry and microstructure observations by optical microscope, scanning and transmission electron microscopy. The typical characteristics were the refined grain, homogeneous precipitates and porosity in the as-deposited pre-forms. The ultimate tensile strength, yield strength, hardness and elongation improved significantly after two passes hot extrusion. A good combination of ultimate tensile strength at 704 MPa and elongation at 9.7% were achieved under peak-aged treatment. The best ultimate tensile strength was obtained at 732 MPa after re-aging and regression. It was main dimple fracture in the extruded and aging treated specimens while brittle fracture for the as-deposited. The secondary phases were main MgZn{sub 2} and Al{sub 3}Zr dispersoids throughout all the states. The contributions of grain boundaries, dislocations, solid-solution and precipitates on the yield strength were analyzed using a quantitative equation.

36 MATERIALS SCIENCE↗

Lattice rotations in precipitate free zones in an Al-Mg-Si alloy

Highlights: • Recovery processes in precipitate free zones differ from those in grain interiors. • Most precipitate free zones contain few dislocations, after deformation. • Deformation can induce large misorientations in precipitate free zones. • Some deformed precipitate free zones contain nanoscale grains. - Abstract: Scanning precession electron diffraction and automated crystal orientation mapping in a transmission electron microscope (TEM) have been applied to quantitatively study the crystal orientation of precipitate free zones (PFZs) of four GB regions in an AA6060 alloy in peak aged condition (temper T6) after uniaxial compression to 20% engineering strain. The PFZ width in the alloy was found to be w = 170 ± 40 nm. The results show that some PFZs develop significant misorientations relative to their parent grain, and represent, to the best knowledge of the authors, the first quantitative evidence of this. This misorientation may either be constant inside a particular PFZ, making it appear like a band or a very elongated subgrain, or be partitioned in discrete regions with a diameter comparable to the PFZ width, making the former PFZ into a collection of small grains. The band-like PFZ observed in this work had a misorientation relative to its parent grain of ≈ 7°, while the grain-like PFZ had grains with misorientations between ≈ 12° and ≈ 20° relative to its parent grain. The other PFZs that were observed had only limited misorientations relative to their parent grains, and had either dislocations perpendicular to the GB plane or a dislocation wall at the transition region. A general TEM study of the material at various engineering strains was also conducted and suggests that grain-like PFZs are more frequent for larger strains, indicating that the different PFZ features are likely due to different strain localisation in individual PFZs. This localisation is expected to be influenced by the orientation of the loading axis relative to crystal orientations and GB planes. It is also suggested that the different PFZ features engender different work hardening rates and possibly affect nucleation of intergranular fracture. The results support previous studies on the microstructure evolution of PFZs in age-hardenable aluminium alloys during deformation.

36 MATERIALS SCIENCE↗

A comparative research on bobbin tool and conventional friction stir welding of Al-Mg-Si alloy plates

Highlights: • 6061-T4 Al plates were successfully welded by both BT-FSW and C-FSW processes. • A wide welding parameter window was achieved with bobbin tool. • BT-FSW joints showed good strength similar to that of C-FSW joints. • Proving that an Isothermal Dissolution Layer Theory also apply to BT-FSW - Abstract: In our work, Al-Mg-Si (6061Al -T4) plates of 6 mm thickness were subjected to bobbin tool friction stir welding (BT-FSW) and conventional friction stir welding (C-FSW) for comparison. How the welding process affects the microstructure and mechanical properties was investigated at various rotation rates and welding speeds. The results showed that butt FSW joints with high quality could be produced at the selected parameters. The joint strength rose with enhanced welding speed and was nearly independent of the rotation rate in both the welding processes. The strength of the joints produced with BT-FSW reached the same level as that of the C-FSW. The maximum joint strength of 229 MPa was 93% of the base material (BM), which is superior to the reported results of 60–80% for the T4 condition. The fracture position of most of the joints was in the heat-affected zone (HAZ), which is the lowest hardness zone.

36 MATERIALS SCIENCE↗

Electrical properties of MgAl{sub 2-2x}Zr{sub x}M{sub x}O{sub 4} (M = Co, Ni and x = 0.00-0.20) synthesized by coprecipitation technique using urea

This paper presents the results of a study concerning the structural and electrical properties of MgAl{sub 2-2x}Zr{sub x}M{sub x}O{sub 4} (x = 0.00-0.20 and M = Co{sup 2+} and Ni{sup 2+}) prepared by a coprecipitation technique using urea as a precipitating agent. The X-ray diffraction data for the pure and its doped samples are consistent with the single-phase spinel and their crystallite sizes are in the range 7-20 {+-} 4 nm. The DC resistivity increases from 3.09 x 10{sup 9} {omega} cm to 6.73 x 10{sup 9} and 8.06 x 10{sup 9} {omega} cm whereas dielectric constant decreases from 5.80 to 5.11 and 4.95 on doping with Zr-Co and Zr-Ni, respectively. The electrical resistivity variations with increase in the dopant contents indicate two types of conduction mechanisms in operation. Several parameters such as, hopping energy (W), metal-semiconductor transition temperature (T{sub MS}) and Debye temperature ({theta}{sub D}) have also been determined. The increase in DC resistivity and decrease in dielectric constant suggest that the synthesized materials can be considered for application as an insulating and structural material in fusion reactors.

36 MATERIALS SCIENCE↗

MgCoAl and NiCoAl LDHs synthesized by the hydrothermal urea hydrolysis method: Structural characterization and thermal decomposition

Highlights: • We synthesized MgCoAl and NiCoAl LDHs by the urea hydrolysis method. • Aluminum rich and crystalline materials have been formed. • The calcination of the LDHs generated mixed oxides with high surface areas. - Abstract: Layered double hydroxides (LDHs) with Mg/Co/Al and Ni/Co/Al were synthesized for the first time by the urea hydrolysis method. The experimental conditions promoted aluminum rich and crystalline materials. The formation of LDHs was investigated by powder X-ray diffraction (XRD), chemical analysis, solid state nuclear magnetic resonance with magic angle spinning ({sup 27}Al-MAS-NMR), simultaneous thermogravimetric/differential thermal analysis (TGA/DTA), FTIR spectroscopy, scanning electron microscopy (SEM), and N{sub 2} adsorption–desorption experiments. A single phase corresponding to LDH could be obtained in all the investigated compositions. Thermal calcination of these LDHs at 500 °C resulted in the formation of solid solutions in which Al{sup 3+} was dissolved. All the calcined materials have rock-salt like structures and high surface areas.

36 MATERIALS SCIENCE↗

Influence of multi-walled carbon nanotubes (MWCNTs) volume percentage on the magnetic and microwave absorbing properties of BaMg{sub 0.5}Co{sub 0.5}TiFe{sub 10}O{sub 19}/MWCNTs nanocomposites

Graphical abstract: Reflection losses of (a) doped barium hexaferrite, BaMg{sub 0.5}Co{sub 0.5}TiFe{sub 10}O{sub 19}, sample and their nanocomposites with (b) 4 vol. (c) 8 vol. and (d) 12 vol.% of MWCNTs are presented. - Highlights: • BaMg{sub 0.5}Co{sub 0.5}TiFe{sub 10}O{sub 19}/MWCNTs nanocomposites were synthesized. • The structural, magnetic and microwave absorption properties were investigated. • The microwave absorption is strongly influenced by volume percentage of MWCNTs. • The nanocomposite with 8 vol.% of MWCNTs can be proposed as a wideband absorber. - Abstract: In this study BaMg{sub 0.5}Co{sub 0.5}TiFe{sub 10}O{sub 19}/MWCNTs nanocomposites with different amount of MWCNTs (0, 4, 8 and 12 vol.%) were synthesized. Here, the X-ray diffraction (XRD), Fourier transform spectroscopy (FTIR) and scanning electron microscopy (SEM) were used to demonstrate the structural and morphological characteristics of the prepared samples. XRD along with FTIR examinations exhibited that the nanocomposites were successfully synthesized. Vibrating sample magnetometer (VSM) showed the relatively strong dependence of saturation magnetization and coercivity on the volume percentage of MWCNTs. The microwave evaluation also confirmed that the complex permittivity of nanocomposites could be enhanced by adding MWCNTs. Finally, the nanocomposite with 8% vol. of MWCNTs exhibited the best microwave absorption performance among the samples.

36 MATERIALS SCIENCE↗

Pulsed laser deposition to synthesize the bridge structure of artificial nacre: Comparison of nano- and femtosecond lasers

Nature offers inspiration to new adaptive technologies that allow us to build amazing shapes and structures such as nacre using synthetic materials. Consequently, we have designed a pulsed laser ablation manufacturing process involving thin film deposition and micro-machining to create hard/soft layered 'brick-bridge-mortar' nacre of AlMgB{sub 14} (hard phase) with Ti (soft phase). In this paper, we report pulsed laser deposition (PLD) to mimic brick and bridge structures of natural nacre in AlMgB{sub 14}. Particulate formation inherent in PLD is exploited to develop the bridge structure. Mechanical behavior analysis of the AlMgB{sub 14}/Ti system revealed that the brick is to be 250 nm thick, 9 {mu}m lateral dimensions while the bridge (particle) is to have a diameter of 500 nm for a performance equivalent to natural nacre. Both nanosecond (ns) and femtosecond (fs) pulsed lasers were employed for PLD in an iterative approach that involves varying pulse energy, pulse repetition rate, and target-to-substrate distance to achieve the desired brick and bridge characteristics. Scanning electron microscopy, x-ray photoelectron spectroscopy, and optical profilometer were used to evaluate the film thickness, particle size and density, stoichiometry, and surface roughness of thin films. Results indicated that both ns-pulsed and fs-pulsed lasers produce the desired nacre features. However, each laser may be chosen for different reasons: fs-pulsed laser is preferred for much shorter deposition time, better stoichiometry, uniform-sized particles, and uniform film thickness, while ns-pulsed laser is favored for industrial acceptance, reliability, ease of handling, and low cost.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗