Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Load Distribution”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1929

Pressure Distribution Tests on PW-9 Wing Models from -18 Degree Through 90 Degree Angle of Attack

At the request of the Army Air Corps, an investigation of the pressure distribution over PW-9 wing models was conducted in the atmospheric wind tunnel of the National Advisory Committee for Aeronautics. The primary purpose of these tests was to obtain wind-tunnel data on the load distribution on the cellule to be correlated with similar information obtained in flight tests, both to be used for design purposes. Because of the importance of the conditions beyond the stall as affecting the control and stability, this investigation was extended through 90 degree angle of attack. The results for the range of normal flight have been given in NACA Technical Report No. 271. The present paper presents the same results in a different form and includes, in addition, those over the greater range of angle of attack, -18 degrees through 90 degrees. The results show that: (1) at angles of attack above maximum lift, the biplane upper wing pressures are decreased by the shielding action of the lower wing. (2) the burble of the biplane lower wing, with respect to the angle of attack, is delayed, due to the shielding action of the lower wing. (3) the center of pressure of the biplane upper wing (semispan) is, in general, displaced forward and outward with reference to that of the wing as a monoplane, while for the lower wing there is but slight difference for both conditions. (4) the overhanging portion of the upper wing is little affected by the presence of the lower wing.

Loeser, Oscar E , Jr↗
NASA NTRS1983

Propeller noise prediction

Analytic propeller noise prediction involves a sequence of computations culminating in the application of acoustic equations. The prediction sequence currently used by NASA in its ANOPP (aircraft noise prediction) program is described. The elements of the sequence are called program modules. The first group of modules analyzes the propeller geometry, the aerodynamics, including both potential and boundary layer flow, the propeller performance, and the surface loading distribution. This group of modules is based entirely on aerodynamic strip theory. The next group of modules deals with the actual noise prediction, based on data from the first group. Deterministic predictions of periodic thickness and loading noise are made using Farassat's time-domain methods. Broadband noise is predicted by the semi-empirical Schlinker-Amiet method. Near-field predictions of fuselage surface pressures include the effects of boundary layer refraction and (for a cylinder) scattering. Far-field predictions include atmospheric and ground effects. Experimental data from subsonic and transonic propellers are compared and NASA's future direction is propeller noise technology development are indicated.

Zorumski, W. E.↗
NASA NTRS2004

Combined In-Plane and Through-the-Thickness Analysis for Failure Prediction of Bolted Composite Joints

Although two-dimensional methods provide accurate predictions of contact stresses and bolt load distribution in bolted composite joints with multiple bolts, they fail to capture the effect of thickness on the strength prediction. Typically, the plies close to the interface of laminates are expected to be the most highly loaded, due to bolt deformation, and they are usually the first to fail. This study presents an analysis method to account for the variation of stresses in the thickness direction by augmenting a two-dimensional analysis with a one-dimensional through the thickness analysis. The two-dimensional in-plane solution method based on the combined complex potential and variational formulation satisfies the equilibrium equations exactly, and satisfies the boundary conditions and constraints by minimizing the total potential. Under general loading conditions, this method addresses multiple bolt configurations without requiring symmetry conditions while accounting for the contact phenomenon and the interaction among the bolts explicitly. The through-the-thickness analysis is based on the model utilizing a beam on an elastic foundation. The bolt, represented as a short beam while accounting for bending and shear deformations, rests on springs, where the spring coefficients represent the resistance of the composite laminate to bolt deformation. The combined in-plane and through-the-thickness analysis produces the bolt/hole displacement in the thickness direction, as well as the stress state in each ply. The initial ply failure predicted by applying the average stress criterion is followed by a simple progressive failure. Application of the model is demonstrated by considering single- and double-lap joints of metal plates bolted to composite laminates.

Kradinov, V.↗
NASA NTRS1942

Pressure distribution on wings in reversed flow

The series of pressure distribution measurements at three test sections on NACA airfoils 2212 and M6 within 170 to 210 angles of attack in reversed flow proved to be largely independent of the profile form. In contradiction to the pressure distribution in normal flow considerable negative pressure from the upper surface spills over onto the lower surface, and vice versa, even in the zone of sound flow. The results are presented as chord-wise pressure and load distribution. The spanwise lift distribution and the total lift coefficients of the wing obtained by integration manifest approximate agreement with the behavior of a diagonally disposed flat plate. By consideration of the ground effect (represented by a flat wall) the lower surface of the wing shows an increase in the low pressure.

Naumann, A↗
NASA NTRS1994

Gear tooth topological modification

The topology of parallel axis gears, such as spur and helical gears is modified to produce quieter and more smoothly operating gear sets with more uniform load distribution. A finite element analysis of the gear in its operating mode is made to produce a plot of radial and tangential deflections of the pinion and gear tooth surfaces which will occur when the gears are loaded during operation. The resultant plot is then inverted to produce a plot, or set of coordinates, which will define the path of travel of the gear tooth grinding wheel, which path is a mirror image of the plot of the finite element analysis. The resulting gears, when subjected to operating loads, will thus be deflected tangentially and radially to their optimum operating, or theoretical true involute, positions so as to produce quieter, smoother, and more evenly loaded gear trains.

Kish, Jules G.↗
NASA NTRS1990

Balancing Loads Among Robotic-Manipulator Arms

Paper presents rigorous mathematical approach to control of multiple robot arms simultaneously grasping one object. Mathematical development focuses on relationship between ability to control degrees of freedom of configuration and ability to control forces within grasped object and robot arms. Understanding of relationship leads to practical control schemes distributing load more equitably among all arms while grasping object with proper nondamaging forces.

Kreutz, Kenneth K.↗
NASA NTRS1977

Determining the Lift and Drag Distributions on a Three-Dimensional Airfoil from Flow-Field Velocity Surveys

The application of the incompressible momentum integral equation to a three-dimensional airfoil was reviewed to interpret the resulting equations in a way that suggests a reasonable experimental technique for determining the spanwise distributions of lift and drag. Consideration was given to constraints that must be placed on the character of the vortex wake structure shed by the wing, to provide the familiar relationship between lift and bound vorticity. It is shown that the induced drag distribution is not directly measurable, but can be obtained, via the lift distribution, approximately for a deflected wake and exactly for a planar wake. Moreover, it is shown that it is only necessary to survey a short distance above and below the wing trailing edge. Examples are presented for several typical loading distributions and the results of a numerical simulation of the suggested experiment are discussed.

Orloff, K. L.↗
NASA NTRS1931

The pressure distribution over a modified elliptical wing tip on a biplane in flight

This note presents the results of flight pressure-distribution tests on the right upper wing panel of a Douglas M-3 airplane equipped with a modified elliptical tip having a slight amount of washout. The results are given in tables and curves in such form that the load distribution for any normal force coefficient within the usual range encountered in flight may be determined.

Lundquist, Eugene E↗
NASA NTRS1954

Effects of Wing Leading-Edge Camber and Tip Modifications on the Aerodynamic Characteristics of a 1/20-Scale Model of the Convair F-102 Airplane at Transonic Speeds

The effects of several wing leading-edge camber and deflected-tip modifications on the force and moment characteristics of a 1/20-scale model of the Convair F-102 airplane have been determined at Mach numbers from 0.60 t o 1.14 for angles of attack up to 14 deg. in the Langley 8-foot transonic tunnel. The effects of elevator deflections from 0 deg. to -10 deg. were also obtained for a configuration incorporating favorable leading- edge and tip modifications. Leading-edge modifications which had a small amount of constant-chord camber obtained by vertically adjusting the thickness distribution over the forward (3.9 percent of the mean aerodynamic chord) portion of the wing were ineffective in reducing the drag at lifting conditions at transonic speeds. Leading edges with relatively large cambers designed to support nearly elliptical span load distributions at lift coefficients of 0.15 and 0.22 near a Mach number of 1.0 produced substantial reductions in drag at most lift coefficients.

Tempelmeyer, Kenneth E.↗
NASA NTRS2006

Nonlinear Spring Finite Elements for Predicting Mode I-Dominated Delamination Growth in Laminated Structure with Through-Thickness reinforcement

One particular concern of polymer matrix composite laminates is the relatively low resistance to delamination cracking, in particular when the dominant type of failure is mode I opening. One method proposed for alleviating this problem involves the insertion pultruded carbon pins through the laminate thickness. The pins, known as z-pins, are inserted into the prepreg laminate using an ultrasonic hammer prior to the curing process, resulting in a field of pins embedded normal to the laminate plane as illustrated in Figure. 1. Pin diameters range between 0.28-mm to 0.5-mm and standard areal densities range from 0.5% to 4%. The z-pins are provided by the manufacturer, Aztex(Registered TradeMark) , in a low-density foam preform, which acts to stabilize orientation of the pins during the insertion process [1-3]. Typical pin materials include boron and carbon fibers embedded in a polymer matrix. A number of methods have been developed for predicting delamination growth in laminates reinforced with z-pins. During a study on the effect of z-pin reinforcement on mode I delamination resistance, finite element analyses of z-pin reinforced double cantilever beam (DCB) specimens were performed by Cartie and Partridge [4]. The z-pin bridging stresses were modeled by applying equivalent forces at the pin locations. Single z-pin pull-out tests were performed to characterize the traction law of the pins under mode I loading conditions. Analytical solutions for delamination growth in z-pin reinforced DCB specimens were independently derived by Robinson and Das [5] and Ratcliffe and O'Brien [6]. In the former case, pin bridging stresses were modeled using a distributed load and in the latter example the bridging stresses were discretely modeled by way of grounded springs. Additionally, Robinson and Das developed a data reduction strategy for calculating mode I fracture toughness, G(sub Ic), from a z-pin reinforced DCB specimen test [5]. In both cases a traction law similar to that adopted by Cartie and Partridge was used to represent z-pin failure under mode I loading conditions. In the current work spring elements available in most commercial finite element codes were used to model z-pins. The traction law used in previous analyses [4-6] was employed to represent z-pin damage. This method is intended for and is limited to simulating z-pins in composite laminate structure containing mode I-dominated delamination cracking. The current technique differs from previous analyses in that spring finite elements (available in commercial codes) are employed for simulating zpins, reducing the complexity of the analysis construction process. Furthermore, the analysis method can be applied to general structure that experiences mode I-dominated delamination cracking, in contrast to existing analytical solutions that are only applicable to coupon DCB specimens.

Ratcliffe, James G.↗
NASA NTRS2020

Bi-Axial Load Testing of a Woven-Webbing Inflatable Space Habitat Restraint Layer Component

This report discusses testing of a bi-axial woven panel consisting of high-strength webbings that represent a portion of the structural restraint layer of an inflatable space structure. Inflatable softgoods vessels are being researched for human space missions as possible habitats, airlocks and tunnel elements. Understanding the complex behavior of the softgoods restraint layer and maturing finite element analysis capabilities to model these structures is critical to their successful implementation. The primary goal of this research is to study the load-up and load distribution in a weave of webbings, before and after the loss of tension in one of the webbings. In addition, a key objective is to evaluate the ability to convert strains measured via photogrammetry using digital image correlation to loads in the weave. The report gives an introduction and objectives for the test program and a description of the test fixture, setup and procedure. This is followed by a section focusing on the test data and associated discussion. To streamline presentation of the data, one focus case is detailed in the main text. (Comprehensive data set can be found in Appendix A for the three remaining test cases.) In addition to the load and time histories for one case, summary charts and tables that incorporate data from all four test cases are provided. The concluding remarks include major findings, lessons learned and recommendations for future work. Appendix B provides complementary full-field strain results when considering the existing woven webbing data as a fabric. These types of results could inform models intended for global representation. Appendix C contains a description from a series of exploratory instrumented hammer tap tests and results on the weave. These tests describe an area of research for the biaxial test fixture beyond the current testing studying the propagation and detection of vibrations in a tensioned weave that has applications in impact and damage detection.

Karen H Lyle↗
NASA NTRS2013

Atmospheric Entry Studies for Venus Missions: 45 Sphere-Cone Rigid Aeroshells and Ballistic Entries

The present study considers direct ballistic entries into the atmosphere of Venus using a 45deg sphere-cone rigid aeroshell, a legacy shape that has been used successfully in the past in the Pioneer Venus Multiprobe Mission. For a number of entry mass and heatshield diameter combinations (i.e., various ballistic coefficients) and entry velocities, the trajectory space in terms of entry flight path angles between skip out and -30deg is explored with a 3DoF trajectory code, TRAJ. From these trajectories, the viable entry flight path angle space is determined through the use of mechanical and thermal performance limits on the thermal protection material and science payload; the thermal protection material of choice is entry-grade carbon phenolic, for which a material thermal response model is available. For mechanical performance, a 200 g limit is placed on the peak deceleration load experienced by the science instruments, and 10 bar is assumed as the pressure limit for entry-grade carbon-phenolic material. For thermal performance, inflection points in the total heat load distribution are used as cut off criteria. Analysis of the results shows the existence of a range of critical ballistic coefficients beyond which the steepest possible entries are determined by the pressure limit of the material rather than the deceleration load limit.

Prabhu, Dinesh K.↗
NASA NTRS1984

Latch for Stored Cargo

Spherical latch elements distribute load over broad area. Concave and convex latching surfaces couple with one another to secure payload. Motor-drive pin locks latch in place; for active latch, second motor turns connecting plate attached to concave latch element. Spherical shape of latching elements distributes cargo weight over broad surface so no "hotspots" when cargo secured.

Clark, K. H.↗
NASA NTRS1973

On the inviscid rolled-up structure of lift-generated vortices

A simple form is presented of the relationships derived by Betz for the inviscid, fully developed structure of lift-generated vortices behind aircraft. An extension is then made to arbitrary span-load distributions by inferring guidelines for the selection of rollup centers for the vortex sheet. These techniques are easier to use and yield more realistic estimates of the rolled-up structure of vortices than the original form of Betz' theory when the span loading differs appreciably from elliptic loading.

Rossow, V. J.↗
NASA NTRS1978

Numerical study of transonic flow over oscillating airfoils using the full potential equation

The behavior of unsteady aerodynamic loadings on airfoils oscillating in transonic flow has been investigated numerically with particular attention given to supercritical airfoil sections. A previously developed finite difference method, which is based on the full potential equation and which uses a quasi-conservative scheme for proper capture of a shock wave motion, was employed for the present study. The unsteady aerodynamic pressure and load distributions on several different airfoil sections are presented with particular emphasis on the effects of free-stream Mach number, reduced frequency, and mean angle of attack. These parameters are demonstrated to have a significant effect on the behavior of the unsteady aerodynamic loadings. Comparisons of the present calculations with the exact inviscid solution and with the experimental results are also presented.

Isogai, K.↗
DOE OSTI2023

Power Flow Models of Grid-Forming Inverters in Unbalanced Distribution Grids

Load unbalance in electric distribution systems is unavoidable. Unbalanced load currents will lead to negative sequence (NS) voltages that may damage electric equipment. Unbalanced power flow analysis is a common tool to detect and mitigate NS voltage issues and requires accurate models of grid components. While traditional source models are available, grid-forming (GFM) inverter models are not well developed. GFM inverters implement various control strategies, which affect their power flow models. Here, in this paper, a novel GFM inverter model considering control effects is proposed. We show that for some control methods, unbalanced system loading will lead to unbalanced terminal voltages of the GFM inverters, which are modeled through an equivalent negative sequence impedance. The proposed models are initially validated using a simple test circuit. Then, they are applied in the power flow analysis on the IEEE 13-bus and 34-bus systems to demonstrate the accuracy improvement over the state-of-the-art. Using time-domain simulations as benchmarks, we show that the proposed models reduce the calculation error of negative sequence voltages by at least 25% in unbalanced distribution systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗
DOE OSTI2021

FAST.Farm load validation for single wake situations at alpha ventus

The main objective of the presented work is the validation of the simulation tool FAST.Farm for the calculation of power and structural loads in single wake situations; the basis for the validation is the measurement database of the operating offshore wind farm alpha ventus. The approach is described in detail and covers the calibration of the aeroelastic turbine model, transfer of environmental conditions to simulations, and comparison between simulations and adequately filtered measurements. It is shown that FAST.Farm accurately predicts power and structural load distributions over wind direction with discrepancies of less than 10 % for most of the cases compared to the measurements. Additionally, the frequency response of the structure is investigated, and it is calculated by FAST.Farm in good agreement with the measurements. In general, the calculation of fatigue loads is improved with a wake-added turbulence model added to FAST.Farm in the course of this study.

17 WIND ENERGY↗
NASA NTRS1977

Effects of jet decay rate on jet induced loads on a flat plate

Experimental modelling of the interaction between a jet and an aircraft wing or fuselage in VTOL aircraft was undertaken using a cold jet exiting perpendicular to a flat plate in a uniform cross-flow. Effects of jet decay rate and jet-to-cross-flow velocity ratio, R, on the induced load distribution were investigated. Jet decay rate was increased by using cylindrical centerbodies submerged in the jet nozzle, which caused nonuniform initial jet velocity profiles. Quicker jet decay rate, corresponding to the presence of a centerbody, resulted in as much as 50% reduction in the induced pressure loads on the plate. This has implications in interpretation of results from earlier VTOL model studies of jet induced loads, where the jets have often had relatively slow decay rates due to uniform initial velocity profiles

Kuhlman, J. M.↗