Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Lithium Battery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Polymers in Lithium‐Ion and Lithium Metal Batteries

Abstract Lithium‐ion batteries play a significant role in modern electronics and electric vehicles. However, current Li‐ion battery chemistries are unable to satisfy the increasingly heightened expectations regarding energy demand and reliability. To boost the overall energy density while ensuring the safety of Li batteries, researchers have focused on alternative battery materials, such as silicon, sulfur, and Li metal. These represent promising avenues, although numerous obstacles (e.g., Si cracking, polysulfide shuttling, Li dendrites, etc.) must be tackled before batteries based on these materials can enter mass production and penetrate the mainstream market. Polymers are a class of materials that are widely used in current battery systems; however, many novel polymer chemistries may offer better performance and reliability than the current ones, and even overcome the issues of the above‐mentioned new battery materials. In this review, selected polymeric materials for solving these issues are categorized into four parts: polymer electrolytes, polymer artificial solid‐electrolyte interphases, binders, and separators. Both the current progress and the characterization methods are included. Potential future directions of energy materials research are pointed out as well.

Li, Junheng↗
DOE OSTI2021

Electrolytes Polymerization‐Induced Cathode‐Electrolyte‐Interphase for High Voltage Lithium‐Ion Batteries

Abstract Lithium‐ion batteries (LIBs) based on LiNi x Co y Mn 1‐x‐y O 2 (NCM) cathode materials have been widely commercialized, because of their high energy density, favorable rate performance, and relatively low cost. However, with increased Ni content to further increase their energy density, their cycling stability deteriorates dramatically and thus fails to meet the commercial application requirements. The artificial cathode‐electrolyte‐interphase (CEI) is a promising approach to solve this problem. Here, a robust CEI is fabricated through in situ polymerization of ethylene carbonate induced by aluminum isopropoxide (AIP). By adding 1 wt.% AIP in a commercial electrolyte, the capacity retention of LiNi 0.8 Co 0.1 Mn 0.1 O 2 ||Li cell at 1 C rate has been significantly increased from 80.8% to 97.8% with a highly reversible capacity of 176 mA h g −1 after 200 cycles. AIP can be also used as an additive during the slurry‐making process, enabling a reversible capacity of 170 mA h g −1 for LiCoO 2 after 200 cycles even at a high charge cut‐off voltage of 4.6 V. It is confirmed that the in situ formed CEI layer can prevent the cathodes from cracking and reduce the irreversible phase transformation.

Yang, Jixiang↗
DOE OSTI2022

An Integrated Flame Spray Process for Low Cost Production of Battery Materials for Lithium Ion Batteries and Beyond

The overall objective of this project was to develop an advanced manufacturing technology for Li-ion battery materials production at low cost and in a green chemical process using glycerol as solvent to replace water. It was aimed at developing a prototype pilot production line to reduce production cost by at least 25% to the baseline. During the course of this project, research was conducted to understand spray drying and combustion of eutectic solvent precursors of glycerol and metal salts (acetates) in the formation of mixed metal oxide powders. Reactor design and optimization were done to facilitate spray drying and combustion in powder formation and processing. Various cathode materials powders were produced, including lithium nickel-cobalt-manganese oxide (NCM) and lithium nickel-cobalt-aluminum oxide (NCA). These cathode materials powders were tested in half coin cells for their performances, with materials performances of 160 mAh/g for NCM111 and 200 mAh/g for NCA. NCA powders were also produced using a slurry spray-drying process and tested in full pouch cells. A pilot scale flame assisted spray drying reactor was constructed and demonstrated for its production rate exceeding the target of production rate of four metric tons per year. The work performed in this project has been documented in 9 peer reviewed journal publications, 8 conference presentations, and two IP disclosures/patent applications.

25 ENERGY STORAGE↗
DOE OSTI2020

Understanding and applying coulombic efficiency in lithium metal batteries

Coulombic Efficiency (CE) has been widely used in battery research as a quantifiable monitor to compare the properties and performances of materials, electrolytes, interfaces and the entire electrochemical cells. While CE with ultra high precision effectively predicts the lifespan and health for lithium ion (Li-ion) batteries, it is not necessarily true in rechargeable lithium (Li) metal batteries. A large variation of CE is often seen even from the same materials and electrolytes in Li metal cells. This work discusses the fundamental definition of CE in different configurations of Li metal-based cells. The similarities and differences of CE in Li-ion and Li metal cells have been clarified and used to understand the relevance/irrelevance between CE and cycling. Long-standing goal of this study is to help rational design of cell testing protocols and elaborate electrochemical results. The insights from this work are broadly applicable in many other rechargeable metal cells e.g., Zn, Mg and Na batteries to accelerate reseach innovation.

Xiao, Jie↗
DOE OSTI2023

Poly(vinylferrocene) as an Ionomer and Sulfur-Confining Additive for Lithium–Sulfur Batteries

Lithium-sulfur (Li-S) batteries are promising owing to their high energy density, environmental benignity, and low cost. Most of the commonly used binders in Li-S battery cathodes are inert and have no significant effect on the challenges of sulfur as a cathode material, such as the polysulfide shuttle effect, low ionic/electronic conductivity, and a sluggish redox reaction. In this work, we demonstrate the use of poly(vinylferrocene) (PvFc) as a binder additive that can effectively increase the ionic conductivity of the cathode and act as a sulfide confining agent. Electrochemical tests performed with PvFc as part of the binder mixture used to cast the cathodes demonstrate an increase in rate capability and cycle life when compared to the baseline samples. Ionic conductivity measurements and X-ray photoelectron spectroscopy suggest that the π-cation molecular interaction between the cyclopentadienyl rings from ferrocene and Li + act like an ion couple with ferrocene acting as a static, covalently bound acceptor of Li + ions that enhances their mobility through the cathode. This coupled with the affinity between the ferrocenyl cations and the Li salt anions, which provides more distribution of counterions for Li + movement and improves accessibility to the cathode S reservoir, make PvFc a promising ionomer for Li-S batteries. In addition, the π-cation bonds between cyclopentadienyl and lithium polysulfides produce a sulfide confining effect that mitigates capacity fade through polysulfide dissolution. Furthermore, this work demonstrates an expansion in the utility of PvFc as a component in Li-ion batteries, which so far is mostly limited to use as an active material in organometallic batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

High spatial resolution neutron imaging of lithium-ion batteries: Correlating microstructure and lithium transport

Thick electrodes for lithium-ion batteries can increase the overall energy density, but increasing the electrode thickness introduces charge transport limitations. These limitations may be mitigated through proper electrode structuring. Here, high spatial resolution neutron imaging was used to understand the correlation between microstructure and lithium transport in lithium-ion anodes. Batteries with distinct graphite anode microstructures were produced and studied with high spatial resolution in operando neutron radiography to observe the effects of structure on transport. High spatial resolution neutron computed tomography was performed following in operando neutron radiography. X-ray computed tomography and scanning electron microscopy were used to observe the finer scale anode structure to complement neutron imaging. Solvent-free anodes containing a tightly-packed layered structure confined lithium movement close to the separator. This structure limited capacity, but supported better rate capability. Conversely, a more open pore structure in the wet cast anodes yielded higher capacity with reduced rate capability. Together, these results show that lithium distributions can be controlled by the macroscopic structure of the electrodes, the microstructural pore network, and the microscale active areas that support electrochemical reactions. Furthermore, multimodal imaging applying the complementary strengths of neutron and X-ray methods is shown as a tool for advancing battery design.

25 ENERGY STORAGE↗
DOE OSTI2020

Design rules for liquid crystalline electrolytes for enabling dendrite-free lithium metal batteries

Significance Lithium metal anodes offer a promising approach to improve the energy density of batteries to enable electrification of transportation. Dendrite suppression plagues the safety and cycle life of lithium metal anodes. In this work, we perform a comprehensive analysis of the use of liquid crystalline electrolytes in lithium metal anodes. We report theoretical demonstration of spontaneous stabilization of metal-electrode position using a liquid crystalline electrolyte due to the energy that arises when the molecules of the liquid crystal reorient. Building on this, we develop a comprehensive set of molecular-level design rules that will pave the way toward the realization of this new class of electrolytes for practical lithium metal batteries.

Ahmad, Zeeshan↗
NASA NTRS2009

Data Base and Guidelines Document Developed for Lithium-Ion Battery

Lithium-Ion (Li-Ion) batteries are fast becoming the battery chemistry of choice for aerospace applications requiring (rechargeable) power supplies. These batteries offer high-energy density and high-specific energy combined with excellent rate capability and cycle potential. The increased energy content and operational characteristics of this system require defined safety and handling procedures to ensure the safe implementation. Standardized approaches to defining, determining, and addressing safety, handling, and qualification for Li-Ion batteries have been developed and published as an NESC-sponsored Li-Ion Battery Guidelines Document. A data base was established cataloging cells and batteries that have been considered for aerospace applications.

Data Base and Guidelines↗
DOE OSTI2023

Super p-sulfur cathodes for quasi-solid-state lithium-sulfur-batteries

Lithium-Sulfur (Li-S) batteries have become a promising candidate to meet the current energy storage demand, with its natural abundance of materials, high theoretical capacity of 1672 mAhg-1, high energy density of 2600 Whkg-1, low cost and lower environmental impact. Sulfide based solid state electrolytes (SSEs) have received greater attention due to their higher ionic conductivity, compatible interface with sulfur-based cathodes, and lower grain boundary resistance. However, the interface between SSEs and cathodes has become a challenge in all solid-state Li-S batteries due to the rigidity of the participating surfaces. A hybrid electrolyte containing SSE coupled with a small amount of ionic liquid, was essential to improve the interface contact of the SSE with the electrodes. Coating-based cathodes were successfully fabricated using water-based carboxymethyl cellulose (CMC) solution and Styrene butadiene rubber (SBR) as the binder with low sulfur loading (0.70 mgcm-2) as well as high sulfur loading (4.0 mgcm-2). Solid-state composite powder-based cathodes pressed onto SSE (loading 4.0 mgcm-2) with enhanced electronic and ionic conductivity were fabricated with Super P: Sulfur (SP:S) and SSE. Ionic Liquids (IL) prepared using Lithium bis(trifluoromethyl sulfonyl)imide (LiTFSI) as salt, with premixed pyrrolidinium bis(trifluoromethyl sulfonyl)imide (PYR) as solvent and 1,3-dioxolane (DOL) as diluent were used to wet both SSE-electrode interfaces. The effect of IL dilution, co-solvent amount, LiTFSI concentration, C rate at which the batteries are tested and the effect of SSE inside the cathode, were systematically studied and optimized to develop a quasi-solid-state electrolyte Li-S battery (QSSLSB) with higher capacity retention and cyclability. LiTFSI (2M) dissolved in PYR:DOL(1:1) found to be optimum IL combination for low sulfur loading QSSLSBs reaching 500 mAh/g after 100 cycles while LiTFSI (3M) in PYR:DOL(1:3) was the optimum IL concentration for higher loading QSSLSBs reaching 400 mAh/g after 100 cycles. This work reports promising results of QSSLSB based on novel Li6PS5F0.5Cl0.5 Li-argyrodite solid-state electrolyte (SSE) with minute amount of IL, Super P-Sulfur (SP:S) cathode, and Li-anode. It also offers a new insight into the intimate interfacial contacts between the SSE and carbon-sulfur cathodes, which will be critical for improved electrochemical performance of quasi-solid-state lithium-sulfur batteries with high sulfur loading in the future.

25 ENERGY STORAGE↗
DOE OSTI2021

Balancing Interfacial Reactions to Achieve Long Cycle Life in High Energy Lithium Metal Batteries

Rechargeable lithium (Li) metal batteries have attracted wide attentions as the next generation energy storage technologies. However, simultaneously achieving high cell-level energy density and long cycle life in realistic batteries is still a great challenge. Here we investigate the cell degradation mechanisms of Li||LiNi0.6Mn0.2Co0.2O2 pouch cells using different, but representative cell configurations to understand the fundamental linkage among Li thickness, electrolyte depletion and the structure evolution of solid electrolyte interphase (SEI) layers. Different cell failure modes were discovered when tuning the anode to cathode capacity (N/P) ratio in compatible electrolyte. With a thick-Li anode (N/P ratio = 2.5), initial stable cycling is obtained because of the abundant Li supply from the anode together with an artificially inflated high Coulombic Efficiency, followed by a premature sudden cell death appears due to the enrichment of “ineffective SEI” which does not participate in the electrochemical reactions but keep increasing cell impedance. The anode-free cell (N/P 0:1) displays a steady capacity decay because cathode Li loss dominates from the beginning to the end of cell cycle life. An optimized thin-Li (N/P 1:1) well balances the Li consumption rate with the impedance buildup by minimizing the growth of ineffective SEI layer, thus decelerates cell polarization increasing and extends cycling. Contrary to conventional wisdoms, long cycle life is observed by using ultra thin-Li (20 µm) in balanced cells. A prototype 350 Wh kg-1 pouch cell (2.0 Ah) achieves over 600 long stable cycles with 76% capacity retention without sudden cell death.

Niu, Chaojiang↗
NASA NTRS2002

Novel Molecular Architectures Developed for Improved Solid Polymer Electrolytes for Lithium Polymer Batteries

Lithium-based polymer batteries for aerospace applications need the ability to operate in temperatures ranging from -70 to 70 C. Current state-of-the-art solid polymer electrolytes (based on amorphous polyethylene oxide, PEO) have acceptable ionic conductivities (10-4 to 10-3 S/cm) only above 60 C. Higher conductivity can be achieved in the current systems by adding solvent or plasticizers to the solid polymer to improve ion transport. However, this can compromise the dimensional and thermal stability of the electrolyte, as well as compatibility with electrode materials. One of NASA Glenn Research Center's objectives in the PERS program is to develop new electrolytes having unique molecular architectures and/or novel ion transport mechanisms, leading to good ionic conductivity at room temperature and below without solvents or plasticizers.

Meador, Mary Ann B.↗
DOE OSTI2021

Significant life extension of lithium-ion batteries using compact metallic lithium reservoir with passive control

Both traditional graphite-based lithium-ion batteries and next generation silicon-based chemistries suffer significant capacity fade from loss of cyclable lithium due to continued solid-electrolyte interphase growth. A possible engineering solution to maintaining the capacity of cells is incorporating a metallic lithium reservoir and discharging the reservoir into a working electrode to make up for lost cyclable lithium. Here, metallic lithium reservoirs are inserted into both pouch- and cylindrical-format cells. Significant capacity recovery and lifetime extension are demonstrated for traditional graphite and Si/graphite-based cells. In this work, a combination of post-mortem characterization and modeling provide insight into how the lithium distribution as a function of position from reservoir vary with recovery rate. The potential of using passive control to potentially eliminate the need for extra wiring for the third electrode is explored using a simple resistor.

25 ENERGY STORAGE↗
DOE OSTI2020

Cation Additive Enabled Rechargeable LiOH‐Based Lithium–Oxygen Batteries

Abstract Lithium–oxygen (Li–O 2 ) batteries have attracted extensive research interest due to their high energy density. Other than Li 2 O 2 (a typical discharge product in Li–O 2 batteries), LiOH has proved to be electrochemically active as an alternative product. Here we report a simple strategy to achieve a reversible LiOH‐based Li–O 2 battery by using a cation additive, sodium ions, to the lithium electrolyte. Without redox mediators in the cell, LiOH is detected as the sole discharge product and it charges at a low charge potential of 3.4 V. A solution‐based reaction route is proposed, showing that the competing solvation environment of the catalyst and Li + leads to LiOH precipitation at the cathode. It is critical to tune the cell chemistry of Li–O 2 batteries by designing a simple system to promote LiOH formation/decomposition.

Bi, Xuanxuan↗
DOE OSTI2026

Effect of Antagonistic Binder–Catalyst Interactions on Catalytic Activity in Lithium–Sulfur Batteries

Lithium-sulfur (Li-S) batteries are a promising next-generation energy storage solution, as they can reduce reliance on critical transition metals while offering high energy densities. However, their deployment is hindered by low sulfur utilization and the formation/diffusion of lithium polysulfides (LiPSs). While transition-metal catalysts and polymeric binders have been independently developed to enhance redox kinetics and LiPS adsorption, their mutual compatibility has remained largely unexplored. We show here that binder-catalyst interactions can significantly impact catalytic performance. Employing TiO 2 as a generic catalyst, the electrochemical performance is shown to depend strongly on the binder environment. TiO 2 paired with lithiated polyacrylic acid (LiPAA) shows benign interactions, resulting in enhanced cycle life. In contrast, pairing TiO 2 with protonated PAA produces antagonistic interactions that hinder Li 2 S growth. A mechanistic analysis unveils that the carboxylic H atom in PAA promotes COO − coordination to Ti sites, occupying catalytic centers and suppressing LiPS adsorption, increasing charge transfer and diffusion resistances. This phenomenon is observed across multiple catalysts, indicating that COOH-functionalized binders may broadly hinder catalytic activity. Overall, this study underscores the need for holistic cathode design and identifies binder-catalyst compatibility as an important parameter for high-performance Li-S batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Understanding Solid-Electrolyte Interphase Formation at the Lithium Metal Anode of Lithium-Sulfur Batteries

Lithium-sulfur (Li-S) batteries are one of the most promising chemistries for the next generation of energy storage devices. In a standard Li-S cell, the metallic lithium anode is an essential component of the battery due to its low density, extremely high theoretical specific capacity, and very low negative electrochemical potential. However, several challenges related to the use of Li metal have prevented this battery technology from becoming commercially available. For instance, Li-anodes are highly reactive, which results in the continuous decomposition of the electrolyte and the formation of the solid-electrolyte interphase (SEI) layer. This, combined with the non-uniform deposition of Liions during plating at the anode surface, can seriously affect the performance, cycling, and safety of the battery. In addition, it has been suggested that a controlled SEI formation at the metallic Li anode can yield enhanced battery performance. Hence, a comprehensive understanding of how the SEI layer is formed can help elucidate improvements in this battery technology. In this work, the formation of the SEI layer in Li-S batteries is investigated using density functional theory (DFT) and ab initio molecular dynamics (AIMD) simulations. The stability of liquid organic-based electrolyte components, salt concentration, electron-rich environments, and the use of inorganic solid-state electrolyte (SSE) materials are explored in order to provide molecular-level fundamental insights into how the nature and composition of the electrolyte can alter the initial stages of the SEI formation. The products of electrolyte decomposition and electro-/chemical reaction pathways of liquid electrolyte component such as solvent and salts are predicted from AIMD simulations of electrolyte-anode interfaces. Energetics of reactions from DFT ground-state optimizations are also presented to confirm the decomposition mechanisms. Some significant differences are then drawn regarding the use of low and high salt concentrations. Simulations under electron-rich environments show additional multielectron electrochemical reactions of solvent and salt decomposition taking place due to the excess of electrons and the presence of radical anions in the solution. Finally, the initial stages of formation, stability, and main constituents of interfaces between Li-metal and Sbased electrodes with sulfide-based SSEs are characterized in detail.

25 ENERGY STORAGE↗
DOE OSTI2020

Estimating the cost and energy demand of producing lithium manganese oxide for Li-ion batteries

Lithium Manganese Oxide (LMO) is one of the important cathode active materials used in lithium ion batteries of several electric vehicles. In this paper, the production of LMO cathode material for use in lithium-ion batteries is studied. Spreadsheet-based process models have been set up to estimate and analyze the factors affecting the cost of manufacturing, the energy demand, and the environmental impact. Two processes based on the solid-state synthesis method and a sol-gel method have been explored. Results show that the solid-state process is more cost-effective because of its lower cost of raw materials. The production cost for a solid-state process is $7 kg -1 and requires 6 kWh·kg -1 of energy. The pack level cost of electric vehicle battery using LMO as a primary active material is studied as a function of LMO production cost and other parameters. The potential for reducing the cost of automotive batteries to $100 per kWh is explored in terms of LMO price and plant production volume (economy of scale), using Argonne’s BatPaC spreadsheet tool.

25 ENERGY STORAGE↗