SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Reinforced fluorocarbon cupseal, which provides an integral lip-type seal, replaces the metal piston rings in piston-cylinder configurations used in the compression of low density gases. The fluorocarbon seal may be used as cryogenic compressor piston seals.
Seal, machined from a plastic material, prevents liquid hydrogen leakage from hose connectors. It serves as a block-type seal supporting maximum loading of the poppet with slight elastic deflection or as a lip-type seal that is deformed elastically in bending, tension, or compression by the seated poppet.
Tracked air cushion vehicle dynamic heave response, examining flow characteristics, active lip control, guideway contact, acceleration response, etc
Electron microprobe analysis of cavity surface and lip of cosmic dust impact craters in stainless steel plates exposed at 400 km altitude in Gemini S-010 experiment
Replacement of opposing smooth rollers with appropriately grooved rollers in manual tubing cutter allows smooth severance of tubing of different diameters and eliminates raised lip around cut end.
A classical buckling analysis is developed for stiffened, flat plates composed of a series of linked plate and beam elements. Plates are idealized as multilayered orthotropic elements. Structural beads and lips are idealized as beams. The loaded edges of the stiffened plate are simply-supported and the conditions at the unloaded edges can be prescribed arbitrarily. The plate and beam elements are matched along their common junctions for displacement continuity and force equilibrium in an exact manner. Offsets between elements are considered in the analysis. Buckling under uniaxial compressive load for plates, sections, and stiffened plates is investigated. Buckling loads are the lowest of all possible general and local failure modes, and the mode shape is used to determine whether buckling is a local or general instability. Numerical correlations with existing analysis and test data for plates, sections, and stiffened plates including boron-reinforced structures are discussed. In general correlations are reasonably good.
An investigation of the tolerances of two Mach 2.50 axisymmetric mixed-compression inlets to upstream flow variations was conducted. Tolerances of each inlet to angle of attack as a function of decreasing free-stream Mach number were obtained. A local region of overcompression was formed on the leeward side of the inlet at maximum angle of attack before unstart. This region of overcompression corresponded to local subsonic flow conditions ahead of the geometric throat. A uniform Mach number gradient of 0.10 at the cowl lip plane did not affect the inlet's pressure recovery, mass flow ratio, or diffuser exit total-pressure distortion.
The structure of the turbulence in the mixing region for the first few diameters downstream from the outlet of a circular subsonic jet is characterized at three Mach numbers, 0.3, 0.5, and 0.7, with most of the measurements taken at M = 0.3. Profiles of turbulence intensity showed that downstream of the lip intensity is independent of axial distance, while in the core intensity varies by a factor of eight between the jet outlet and the end of the core. A digital data reduction program was used to calculate the auto- and cross-correlations of axial velocity fluctuations and the power spectral densities. Convection velocities were measured using broadband, hot wire signals and signals that were digitally filtered for band-passes about center frequencies of 0.8, 1.3, 1.6, and 3.2 kHz. The center frequency of 1.3 kHz corresponded to the peak energy in the core spectrum. The results support the hypothesis that the coherent pressure field is driven by the intermittent fluctuations at the core boundary, which in turn are related to the large (low frequency) eddies.
Noise measurements were obtained on models of jet-augmented lift systems which are currently being considered for use on proposed short takeoff and landing vehicles. These configurations included a conventional internally blown flap, an augmenter wing, an externally blown flap, and modifications of these basic concepts. The tests were conducted in the Langley anechoic noise facility at zero forward speed with cold air jets. The conventional internally blown flap exhibited lower noise levels than the augmenter wing and the externally blown flap at the same pressure ratios, being of the order of 8 dB or more at the lowest pressure ratio and of the order of 20 dB at the highest pressure ratio of the tests. The data also indicated that for the conventional internally blown flap, there may be an optimum gap size (other than zero) between the turning lip and the flap leading edge from the standpoint of minimum noise generation or admittance. Increasing the trailing-edge thickness of the plain internally blown flap produced no appreciable change in the overall sound pressure level or frequency spectral content in the range of the tests. The data indicated that at a position on the ground directly under the jet exit, the externally blown flap and the augmeter-wing overall noise levels are comparable to each other throughout the pressure range of the tests.
A comprehensive review of currently available techniques pertinent to several prominent aspects of the base thermal problem of the space shuttle booster is given along with a brief review of experimental results. A tractable engineering analysis, capable of predicting the power-on base pressure, base heating, and other base thermal environmental conditions, such as base gas temperature, is presented and used for an analysis of various space shuttle booster configurations. The analysis consists of a rational combination of theoretical treatments of the prominent flow interaction phenomena in the base region. These theories consider jet mixing, plume flow, axisymmetric flow effects, base injection, recirculating flow dynamics, and various modes of heat transfer. Such effects as initial boundary layer expansion at the nozzle lip, reattachment, recompression, choked vent flow, and nonisoenergetic mixing processes are included in the analysis. A unified method was developed and programmed to numerically obtain compatible solutions for the various flow field components in both flight and ground test conditions. Preliminary prediction for a 12-engine space shuttle booster base thermal environment was obtained for a typical trajectory history. Theoretical predictions were also obtained for some clustered-engine experimental conditions. Results indicate good agreement between the data and theoretical predicitons.
A classical buckling analysis is developed for stiffened, flat plates composed of a series of linked flat plate and beam elements. Plates are idealized as multilayered orthotropic elements; structural beads and lips are idealized as beams. The loaded edges of the stiffened plate are simply supported and the conditions at the unloaded edges can be prescribed arbitrarily. The plate and beam elements are matched along their common junctions for displacement continuity and force equilibrium in an exact manner. Offsets between elements are considered in the analysis. Buckling under uniaxial compressive load for plates, sections and stiffened plates is investigated. Buckling loads are found as the lowest of all possible general and local failure modes and the mode shape is used to determine whether buckling is a local or general instability. Numerical correlations with existing analysis and test data for plates, sections and stiffened plates including boron-reinforced structures are discussed. In general, correlations are reasonably good.
Experimental and analytical investigation of the flow field and base pressure of internal-external-expansion truncated plug nozzles are discussed. Experimental results for two axisymmetric, conical plug-cylindrical shroud, truncated plug nozzles are presented for both open and closed wake operations. These results include extensive optical and pressure data covering nozzle flow field and base pressure characteristics, diffuser effects, lip shock strength, Mach disc behaviour, and the recompression and reverse flow regions. Transonic experiments for a special planar transonic section are presented. An extension of the analytical method of Hall and Mueller to include the internal shock wave from the shroud exit is presented for closed wake operation. Results of this analysis include effects on the flow field and base pressure of ambient pressure ratio, nozzle geometry, and the ratio of specific heats. Static thrust is presented as a function of ambient pressure ratio and nozzle geometry. A new transonic solution method is also presented.
Experimental results are reported on the analysis of NERVA structures by photoelasticity. Structures analyzed include butterfly valve lip seal, impeller rotor, and roller bearings.
Direct measurements of the power deposited in the anode of a multimegawatt MPD accelerator using thermocouples attached to a thin shell anode reveal a dramatic decrease in the fractional anode power from 50% at 200 KW input power to less than 10% at 20 MW power. The corresponding local power flux peak at a value of 10,000 W/sq cm at the lip of the anode exhaust orifice, a distribution traced to a corresponding peak in the local current density at the anode. A comparison of voltage-current characteristics and spectral photographs of the MPD discharge using quartz, boron nitride and plexiglas insulators with various mass injection configurations led to the identification of different voltage modes and regions of ablation free operation. The technique of piezoelectric impact pressure measurement in the MPD exhaust flow was refined to account for the effects due to probe yaw angle.
A series of tests were conducted to measure the mass flux in the far field of a nozzle plume in a high vacuum with emphasis on the back flow region. The measurements presented provided fairly accurate data for off-axis angles as large as 140 deg (i.e., in the back flow region). This region, since it is well behind the exit plane, is of paticular interest to those concerned with instrument contamination. Usually sensitive spacecraft surfaces are located in the region affected by the back flow. Parameters such as expansion ratio, throat diameter, nozzle lip shape, and plenum (chamber) pressure were varied, carbon dioxide and nitrogen gases were flowed and mass flux measurements were taken using quartz crystal microbalances in as many as nine different locations relative to the tests nozzle. Several conclusions with respect to the effect of nozzle and gas parameters on the amount of back flow mass flux are offered, and it was demonstrated that gaseous mass fluxes, which are not predictable by present theories, are encountered in the region behind the nozzle exit plane. This knowledge is significant if materials incompatible with the gaseous exhaust products are used in this region.
Aerodynamic and acoustic measurements at a typical STOL aircraft takeoff and landing velocity demonstrated that a 1.35 inlet lip area contraction ratio was superior to a 1.26 ratio at high nacelle incidence angles. Reverse thrust, obtained with a variable pitch rotor, was lower at the landing velocity, and the noise level higher, than at the static condition. High speed tests showed that, for the design cruise Mach number of 0.75, internal losses and external drag were 27 percent of the ideal fan net thrust, and propulsive efficiency was estimated to be 59 percent for an 85 percent efficient fan stage.
A series of tests were conducted to measure the mass flux in the far field of a nozzle plume in a high vacuum with emphasis on the back flow region. The measurements presented in this report provide fairly accurate data for off-axis angles as large as 140 deg (i.e., the back flow region). The tests utilized five different nozzles. Parameters such as expansion ratio, throat diameter, nozzle lip shape, and plenum (chamber) pressure were varied. Carbon dioxide and nitrogen gases were passed through, and mass flux measurements were taken using quartz crystal microbalances in as many as nine different locations relative to the test nozzle. The tests resulted in a large matrix of data that were correlated and compared to existing prediction theories. Several conclusions with respect to the effect of nozzle and gas parameters on the amount of back flow mass flux are offered, and it was demonstrated that gaseous mass fluxes, which are not predictable by present theories, are encountered in the region behind the nozzle exit plane.
An application of the compressibility correction developed by Lieblein and Stockman (1972) to the calculation of flow in axisymmetric inlets is described. The results with experimental data from wind tunnel model tests are compared. The configuration is a conventional subsonic inlet with a NACA series one external cowl shape and a two-to-one ellipse internal lip. It is shown that the compressibility correction gives a relatively good approximation to the internal compressible flow behavior, and thus should be useful in the design and analysis of engine nacelle inlets.