Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Inconel”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Atmospheric braking to circularize an elliptical Venus orbit

The use of atmospheric drag to circularize an elliptical spacecraft orbit at Venus is analyzed parametrically for the Venus Orbital Imaging Radar Mission (VOIR) in 1983. Navigation, maneuver, and guidance requirements are discussed for the decay of a 24-hr orbit to a close circular orbit in about 30-60 days. A prototype 'Aerobrake' is described which is approximately 5 m in diameter and 25 kg in mass and which replaces a chemical retroengine of about 1300 kg in mass (delta V = 2.5 km/s) by a 700 kg in-orbit mass. The aerobrake, a light deployable Inconel sheet, shields the spacecraft from the flow and radiates the aerodynamic heating.

Mcronald, A. D.↗
NASA NTRS1977

Composite pressure vessels for the Space Shuttle Orbiter

During the development of the Space Shuttle Orbiter propulsion and environmental control subsystems it was recognized that use of composite pressure vessels with load sharing liners could provide significant weight savings for high pressure gas containment. A program is described which was undertaken to assess the utility for orbiter applications of titanium 6Al-4V and Inconel 718 liners overwrapped with Kevlar fibers. Vessel characteristics, design features and test results are presented along with brief descriptions of processes and nondestructive evaluation techniques. The resolutions of anomalies and development of design are also presented. Fracture control as applied to the orbiter composite vessels is briefly discussed. Five of the seven titanium lined vessels in the program experienced premature cyclic failures. These failures were shown to be primarily due to metallurgical anomalies rather than an inherent composite design problem. A nonfragmentary leakage mode of failure was demonstrated at operating pressures. The composite designs will be approximately 25 percent lighter than their all metal counterparts.

Ecord, G. M.↗
NASA NTRS1978

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

Mild steel (AISI 1018) was selected as model cold rolling material and Ti-6A1-4V and Inconel 718 were selected as typical hot rolling and cold rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape rolling process were developed. These models utilized the upper bound and the slab methods of analysis, and were capable of predicting the lateral spread, roll separating force, roll torque, and local stresses, strains and strain rates. This computer-aided design system was also capable of simulating the actual rolling process, and thereby designing the roll pass schedule in rolling of an airfoil or a similar shape.

Lahoti, G. D.↗
NASA NTRS1977

Work function determination of promising electrode materials for thermionic converters

Work performed on this contract was primarily for the evaluation of selected electrode materials for thermionic energy converters. The original objective was to characterize selected nickel based superalloys up to temperatures of 1400 K. It was found that an early selection, Inconel 800 produced a high vapor pressure which interfered with the vacuum emission measurements. The program then shifted to two other areas. The first area was to obtain emission from the superalloys in a cesiated atmosphere. The cesium plasma helps to suppress the vaporization interference. The second area involved characterization of the Lanthanum-Boron series as thermionic emitters. These final two areas resulted in three journal publications which are attached to this report.

Jacobson, D.↗
NASA NTRS1977

Multistack nickel-hydrogen units

A typical 625 Inconel pressure vessel, equipped with four thermocouples, has voltage taps not only for the cell, but for each of the several packs inside the container. In a two-stack design, a weld ring is used to separate the packs which, joined together, form one solid group. In the four-stack design, stacks are separated mechanically with about half inch Plexiglas and are connected through the center. Electrolytes are forced out by vacuum. The two stack design is intended for 500 psi and was pressure tested up to 1,000. The problem of electrolyte shorts is discussed and possible solutions for its correction are given.

Smith, J.↗
NASA NTRS1978

Computer-aided analysis and design of the shape rolling process for producing turbine engine airfoils

Mild steel (AISI 1018) was selected as model cold-rolling material and Ti-6Al-4V and INCONEL 718 were selected as typical hot-rolling and cold-rolling alloys, respectively. The flow stress and workability of these alloys were characterized and friction factor at the roll/workpiece interface was determined at their respective working conditions by conducting ring tests. Computer-aided mathematical models for predicting metal flow and stresses, and for simulating the shape-rolling process were developed. These models utilize the upper-bound and the slab methods of analysis, and are capable of predicting the lateral spread, roll-separating force, roll torque and local stresses, strains and strain rates. This computer-aided design (CAD) system is also capable of simulating the actual rolling process and thereby designing roll-pass schedule in rolling of an airfoil or similar shape. The predictions from the CAD system were verified with respect to cold rolling of mild steel plates. The system is being applied to cold and hot isothermal rolling of an airfoil shape, and will be verified with respect to laboratory experiments under controlled conditions.

Lahoti, G. D.↗
NASA NTRS1979

Preliminary design and analysis of large delta wings for earth-to-orbit transports

Two studies are described in which CAD methods are used for preliminary design of advanced earth-to-orbit transport wings. The first structural concept was a multilayer honeycomb wing composed of diffusion-bonded Inconel 718; the second concept (in which structural simplicity was sought) involved a honeycomb sandwich wing, for which only a leading edge and trailing edge spar were used. Some new technologies applicable to advanced wing designs are briefly discussed.

Lemessurier, R. W.↗
NASA NTRS1980

Eliminating underbead fissuring in superalloys

Parameters that produce high-integrity overlay welds in Incoloy-903, Incoloy-88, and Inconel-718 differ from those in conventional metal-in groove welds. Reduced weld velocity eliminates underbead crack-inducing level.

Betts, R. D.↗
NASA NTRS1980

Easily-assembled helical heater

Rugged, compact heater is made from 0.1 mm diameter Inconel wire (125 ohms per meter). Heating element is enclosed in PTFE heat-shrink sleeve. Ends of coal pass through small ceramic spools and are silver-brazed to lead wires. Junctions are potted in epoxy or silicon and covered with crimp sleeves and heat-shrink tubing.

Pizzeck, D. E.↗
NASA NTRS1979

Aerobraking for planetary missions

This paper is a description of recent work to establish the feasibility of aerobraking for planetary orbit missions. Primary emphasis is on a close (300 km) Venus orbiter in 1984. Performance advantages for close Mars orbiters and geosynchronous round trip missions are also shown. A description of the aerobraking operations scenario is given and encouraging preliminary results of an orbit determination analysis are cited. A spacecraft design is presented that features a forward aeroshield and a 9-meter aft aerobrake of 2 mil Inconel. It is shown that, with relatively minor modifications the current Venus Orbital Imaging Radar (VOIR) mission spacecraft design can be adapted to aerobraking and that the aerobraking concept enables the VOIR mission in the difficult 1986 and 1988 opportunities.

French, J. R.↗
NASA NTRS1979

Development of RF sputtered chromium oxide coating for wear application

The radio frequency sputtering technique was used to deposite a hard refractory, chromium oxide coating on an Inconel X-750 foil 0.1 mm thick. Optimized sputtering parameters for a smooth and adherent coating were found to be as follows: target-to-substrate spacing, 41.3 mm; argon pressure, 5-10 mTorr; total power to the sputtering module, 400 W (voltage at the target, 1600 V), and a water-cooled substrate. The coating on the annealed foil was more adherent than that on the heat-treated foil. Substrate biasing during the sputter deposition of Cr2O3 adversely affected adherence by removing naturally occurring interfacial oxide layers. The deposited coatings were amorphous and oxygen deficient. Since amorphous materials are extremely hard, the structure was considered to be desirable.

Bhushan, B.↗
NASA NTRS1982

Double-Adhesive Tape Test Reduces Waste

New method for testing peel strength of particular thermal-control tape used on Space Shuttle orbiter radiators requires only half amount of tape of method previously employed. Thermal-control tape consists of layers of FEP, silver, Inconel metal, adhesive, Kapton Film, and second adhesive layer. Method also avoids cost of labor and materials to prepare second test coupon and can be adapted for testing other types of double-faced adhesive tapes in military, industrial and consumer applications.

Lee, L. C.↗
NASA NTRS1981

Development of high-speed balancing technology

An investigation into laser material removal showed that laser burns act in a manner typical of mechanical stress raisers causing a reduction in fatigue strength; the fatigue strength is lowered relative to the smooth specimen fatigue strength. Laser-burn zones were studied for four materials: Alloy Steel 4340, Stainless Steel 17-4 PH, Inconel 718, and Aluminum Alloy 6061-T6. Calculations were made of stress concentration factors K, for laser-burn grooves of each material type. A comparison was then made to experimentally determine the fatigue strength reduction factor. These calculations and comparisons indicated that, except for the 17-4 PH material, good agreement (a ratio of close to 1.0) existed between Kt and Kf. The performance of the 17-4 PH material has been attributed to early crack initiation due to the lower fatigue resistance of the soft, unaged laser-affected zone. Also covered in this report is the development, implementation, and testing of an influence coefficient approach to balancing a long, slender shaft under applied-torque conditions. Excellent correlation existed between the analytically predicted results and those data obtained from testing.

Demuth, R.↗
NASA NTRS1981

The development of an 85-kW (thermal) steam Rankine solar receiver

The receiver is a once-through monotube boiler designed for steam/electric and process steam applications at pressures up to 17.24 MPa (2500 psia) and temperatures up to 704 C (1300 F). The unit is 76.2 cm (30.0 in.) in diameter and 95.8 cm (37.7 in.) in length; it weighs 220 kg (485 lb). Its heat transfer surface, which is 45.7 cm (18 in.) in diameter by 57 cm (22.4 in.) long, is an Inconel 625, cylindrical, tube-coil assembly composed of primary and reheat sections. A test unit was successfully operated at up to 6.9 MPa (1000 psia) and 704 C (1300 F) with solar input from a 11-m-dia parabolic dish concentrator.

Wright, C. C.↗
NASA NTRS1981

Laser-initiated combustion studies of selected aluminum, copper, iron, and nickel alloys

The results of combustion studies at atmospheric pressure on ten metal alloys are presented. The alloys studied were aluminum alloys 1100, 2219, 6061, and tensile-50; 304, 347 and 21-6-9 stainless steel; inconel 600; beryllium copper and a bronze. It was found that once ignition was achieved all alloys would generally burn to completion. The overall combustion process appears to obey a first order rate process. Preliminary conclusions are presented along with recommendations for future work.

Bransford, J. W.↗
NASA NTRS1980

Accelerated Alpha-s deterioration in a geostationary orbit

Between the Teflon substrate and the interference filter a 2 micron varnish layer was sandwiched in. The bending radius of the SSM, measured on a cone, decreased from about 13 mm to 6 mm prior to interference filter fracture, due to increased tensile strength of its substrate. These samples, and for comparison samples of the same make but without varnish and a conductive layer were included in the test. Additionally 2 Teflon FEP samples without the protective interference filter, one of them with a conductive layer, were tested. The sample substrate was 125 micron Teflon FEP, with vapor deposited silver reflector and a thin Inconel film for corrosion protection.

Husmann, O. K.↗
NASA NTRS1982

Evaluation of candidate stirling engine heater tube alloys at 820 deg and 860 deg C

Seven commercial alloys were evaluated in Stirling simulator materials rigs. Five iron base alloys (N-155, A-286, Incoloy 800, 19-9DL, and 316 stainless steel), one nickel base alloy (Inconel 718), and one cobalt base alloy (HS-188) were tested in the form of thin wall tubing in a diesel fuel fired test rig. Tubes filled with hydrogen or helium at gas pressure of 21.6 MPa and temperatures of 820 and 860 C were endurance tested for 1000 and 535 hours, respectively. Results showed that under these conditions hydrogen permeated rapidly through the tube walls, thus requiring refilling during each five hour cycle. Helium was readily contained, exhibiting no measurable loss by permeation. Helium filled tubes tested at 860 C all exhibited creep-rupture failures within the 535 hour endurance test. Subsequent tensile test evaluation after removal from the rig indicated reduced room temperature ductility for some hydrogen-filled tubes compared to helium-filled tubes, suggesting possible hydrogen embrittlement in these alloys.

Misencik, J. A.↗
NASA NTRS1984

Microfissuring in Nickel-Based-Alloy Welds

Cracking mechanisms proposed. Investigation of physical metallurgy of near-solidus integranular cracking or microfissuring in Inconel 718 alloy welds described in report. Investigation sought to identify cause of microfissuring and quantify its behavior.

Thompson, R. G.↗