Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “INLET FLOW”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1960

Performance, Stability, and Control Investigation at Mach Numbers from 0.4 to 0.9 of a Model of the "Swallow" with Outer Wing Panels Swept 25 degree with and without Power Simulation

An investigation of the performance, stability, and control characteristics of a variable-sweep arrow-wing model (the "Swallow") with the outer wing panels swept 25 deg has been conducted in the Langley 16-foot transonic tunnel. The wing was uncambered and untwisted and had RAE 102 airfoil sections with a thickness-to-chord ratio of 0.14 normal to the leading edge. Four outboard engines located above and below the wing provided propulsive thrust, and, by deflecting in the pitch direction and rotating in the lateral plane, also produced control forces. A pair of swept lateral fins and a single vertical fin were mounted on each engine nacelle to provide aerodynamic stability and control. Jets-off data were obtained with flow-through nacelles, stimulating the effects of inlet flow; jet thrust and hot-jet interference effects were obtained with faired-nose nacelles housing hydrogen peroxide gas generators. Six-component force and moment data were obtained through a Mach number range of 0.40 to 0.90 at angles of attack and angles of sideslip from 0 deg to 15 deg. Longitudinal, directional, and lateral control were obtained by deflecting the nacelle-fin combinations as elevators, rudders, and ailerons at several fixed angles for each control.

Runckel, Jack F.↗
DOE OSTI2022

Large eddy simulation of flow through an axisymmetric sudden expansion

Here, this study aims at investigating the inlet flow conditions of flow through an axisymmetric sudden expansion with an expansion ratio of 2.0. A series of large eddy simulations with the WALE model were conducted for different inlet Reynolds numbers ( Re) and turbulence intensities ($u_{rms}/\bar{U}_m$). The reattachment length, defined as the length measured downstream of the expansion where the flow direction is reversed adjacent to the wall ( Lr), was measured for each case. For widely studied inlet turbulence intensity values (TI), the simulation results are in good agreement with the experimental and numerical results reported in the literature. Parametric studies revealed that turbulence intensity affects the critical Reynolds number, marking the transition between the laminar and transition regions and the reattachment length. The critical Reynolds number was found to decrease with increasing turbulence intensity. A correlation expression is proposed. Additional analysis with proper orthogonal decomposition was performed to enhance the understanding of complex flow structures downstream of the expansion. Finally, an overall correlation expression for the reattachment length was obtained for 500 ≤ Re ≤15 000 and 0.2 ≤ TI (%) ≤ 20. For a given turbulence intensity, the reattachment length can be expressed for laminar and turbulent regions as a function of the Reynolds number. The reattachment length in the transition region can be expressed as a fractional average of reattachment lengths for laminar and turbulent flows.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

Internally manifolded flow cell for an all-iron hybrid flow battery

In one example, a system for a flow cell for a flow battery, comprising: a first flow field; and a polymeric frame, comprising: a top face; a bottom face, opposite the top face; a first side; a second side, opposite the first side; a first electrolyte inlet located on the top face and the first side of the polymeric frame; a first electrolyte outlet located on the top face and the second side of the polymeric frame; a first electrolyte inlet flow path located within the polymeric frame and coupled to the first electrolyte inlet; and a first electrolyte outlet flow path located within the polymeric frame and coupled to the first electrolyte outlet. In this way, shunt currents may be minimized by increasing the length and/or reducing the cross-sectional area of the electrolyte inlet and electrolyte outlet flow paths.

Evans, Craig↗
DOE OSTI2023

Internally manifolded flow cell for an all-iron hybrid flow battery

In one example, a system for a flow cell for a flow battery, comprising: a first flow field; and a polymeric frame, comprising: a top face; a bottom face, opposite the top face; a first side; a second side, opposite the first side; a first electrolyte inlet located on the top face and the first side of the polymeric frame; a first electrolyte outlet located on the top face and the second side of the polymeric frame; a first electrolyte inlet flow path located within the polymeric frame and coupled to the first electrolyte inlet; and a first electrolyte outlet flow path located within the polymeric frame and coupled to the first electrolyte outlet. In this way, shunt currents may be minimized by increasing the length and/or reducing the cross-sectional area of the electrolyte inlet and electrolyte outlet flow paths.

Evans, Craig↗
NASA NTRSDate not supplied

Computational Analysis of a Boundary-Layer Ingesting Tailcone Thruster Configuration Within the National Transonic Facility Using the LAVA Solver

Boundary-layer ingesting (BLI) propulsion systems are one of the many technologies currently under investigation within the aerospace community to meet NASA’s Advanced Air Transport Technology project goal of a sustainable future in aviation. To that end, an experimental campaign was conducted in the National Transonic Facility (NTF) to study the propulsion-airframe integration effects of the Boundary-Layer Ingesting Tailcone System installed in the aft portion of a 2.7% scale design of the NASA Common Research Model (CRM). This test was accompanied by a numerical simulation effort using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) solver, to validate the applicability of current best-practice Reynolds-averaged Navier Stokes (RANS) models in accurately predicting the relevant flow-physics in free-air. A total of 205 steady RANS simulations were performed using LAVA, covering the range of conditions present in the NTF test matrix. Flow conditions ranged from 5- to 15-million Reynolds number, Mach numbers of 0.75, 0.80 and 0.85, and angles-of-attack between –3° and 4°. Four different mass-flow plugs were also tested to assess propulsor operating condition effects. Sensitivity to these flow conditions are analyzed in detail, especially in terms of the nacelle flow distortion which was the main subject of the study. Aerodynamic load coefficients, aftbody boundary-layer measurements and fuselage pressure tap results are also discussed, providing a wide range of validation results from this experimental campaign. This validation effort shows that current best-practices using RANS models within the LAVA solver flow solver are well suited for predicting the inlet flow distortion characteristics of novel aircraft configurations employing BLI at the aft end of the fuselage.

AATT↗
NASA NTRSDate not supplied

Computational Analysis of a Boundary Layer Ingesting Tailcone Thruster Configuration Using the LAVA Curvilinear Solver

Boundary layer ingesting (BLI) propulsion systems are one of the many technologies currently under investigation within the aerospace community to meet NASA's Advanced Air Transport Technology project goal of a sustainable future in aviation. To that end, an experimental campaign was conducted in the National Transonic Facility (NTF) wind tunnel to study the propulsion-airframe integration effects of the Boundary Layer Ingesting Tailcone System installed in the aft portion of a 2.7% scale design of the NASA Common Research Model (CRM). This test was accompanied by a numerical simulation effort using the Launch, Ascent, and Vehicle Aerodynamics (LAVA) curvilinear solver to validate the applicability of current best-practice Reynolds-Averaged Navier-Stokes (RANS) models in accurately predicting the relevant flow physics in free-air. A total of 205 steady RANS simulations were performed using LAVA, covering the range of conditions present in the NTF test matrix. Flow conditions ranged from 5- to 15-million Reynolds number, Mach numbers of 0.75, 0.80 and 0.85, and angles of attack between -3 and 4 degrees. Four different mass-flow plugs were also tested to assess propulsor operating condition effects. Sensitivity to these flow conditions is analyzed in detail, especially in terms of the nacelle flow distortion which was the main subject of the study. Aerodynamic load coefficients, aft body boundary layer measurements and fuselage pressure tap results are also discussed, providing a wide range of validation results from this experimental campaign. This validation effort shows that current best-practices using RANS models within the LAVA curvilinear solver flow solver are well suited for predicting the inlet flow distortion characteristics of novel aircraft configurations employing BLI at the aft end of the fuselage. This talk will cover the combined experimental and numerical efforts that resulted from this BLI-focused investigation.

ARMD↗
NASA NTRS1994

Improving Diffusing S-duct Performance by Secondary Flow Control

The objective of this research was to study ways to reduce inlet flow distortion (i.e., total pressure nonuniformity) and improve total pressure recovery in a diffusing S-duct. This was accomplished by controlling the development of secondary flows within the duct through the use of tapered-fin type vortex generators. Reported are results for the bare duct and seven different configurations of vortex generators. Data presented for each configuration include surface static pressure, surface flow visualization, and exit plane total pressure and transverse velocity. The performance of each configuration was assessed by calculating total pressure recovery and inlet distortion descriptors from the data and comparing them to the values for the bare duct. The best configuration tested reduced distortion (as measured by the DC(45) and DC(90) descriptors) by more than 50 percent while improving total pressure recovery by 0.5 percent. These results should provide valuable guidance in designing vortex generator installations in ducts and for assessing the accuracy of computational fluid dynamics (CFD) methods to calculate duct flows with installed vortex generators.

Reichert, Bruce A.↗
NASA NTRS1991

Effects of inlet distortion on the development of secondary flows in a subsonic axial inlet compressor rotor

Detailed flow measurements were taken inside an isolated axial compressor rotor operating subsonically near peak efficiency. Laser anemometer measurements were made with two inlet velocity profiles. One profile consisted of an unmodified baseline flow, and the second profile was distorted by placing axisymmetric screens on the hub and shroud well upstream of the rotor. A primary flow is defined in the rotor and deviations from this primary flow for each inlet flow condition identified. A comparison between the two flow deviations is made to assess the development of a passage vortex due to the distortion of the inlet flow. A comparison of experimental results with computational predictions from a Navier-Stokes solver showed good agreement between predicted and measured flow. Measured results indicate that a distorted inlet profile has minimal effect on the development of the flow in the rotor passage and the resulting passage vortex.

Owen, Albert K.↗
NASA NTRS1947

Effect of combustor-inlet conditions on performance of an annular turbojet combustor

The combustion performance, and particularly the phenomenon of altitude operational limits, was studied by operating the annular combustor of a turbojet engine over a range of conditions of air flow, inlet pressure, inlet temperature, and fuel flow. Information was obtained on the combustion efficiencies, the effect on combustion of inlet variables, the altitude operational limits with two different fuels, the pressure losses in the combustor, the temperature and velocity profiles at the combustor outlet, the extent of afterburning, the fuel-injection characteristics, and the condition of the combustor basket.

Childs, J Howard↗
NASA NTRS1980

Low speed test of the aft inlet designed for a tandem fan V/STOL nacelle

An approximately .25 scale model of a Tandem Fan nacelle designed for a Type A V/STOL aircraft configuration was tested in a 10-by-10 foot wind tunnel. A 12 inch, tip driven, turbofan simulator was used to provide the suction source for the aft fan inlet. The front fan inlet was faired over for this test entry. Model variables consisted of a long aft inlet cowl, a short aft inlet cowl, a shaft simulator, blow-in door passages and diffuser vortex generators. Inlet pressure recovery, distortion, inlet angle of attack separation limits were evaluated at tunnel velocities from 0 to 240 knots, angles of attack from -10 to 40 degrees and inlet flow rates representative of throat Mach numbers of 0.1 to 0.6. High inlet performance and stable operation was verified at all design forward speed and angle of attack conditions. The short aft inlet configuration provided exceptionally high pressure recovery except at the highest combination of angle of attack and forward speed. The flow quality at the fan face was somewhat degraded by the addition of blow-in door passages to the long aft inlet configuration due to the pressure disturbances generated by the flow entering the diffuser through the auxiliary air passages.

Rhoades, W. W.↗
NASA NTRS1996

Scanning Mode Sensor for Detection of Flow Inhomogeneities

A scanning mode sensor and method is provided for detection of flow inhomogeneities such as shock. The field of use of this invention is ground test control and engine control during supersonic flight. Prior art measuring techniques include interferometry, Schlieren, and shadowgraph techniques. These techniques, however, have problems with light dissipation. The present method and sensor utilizes a pencil beam of energy which is passed through a transparent aperture in a flow inlet in a time-sequential manner so as to alter the energy beam. The altered beam or its effects are processed and can be studied to reveal information about flow through the inlet which can in turn be used for engine control.

Adamovsky, Grigory↗
NASA NTRS1998

Scanning Mode Sensor for Detection of Flow Inhomogeneities

A scanning mode sensor and method is provided for detection of flow inhomogeneities such as shock. The field of use of this invention is ground test control and engine control during supersonic flight. Prior art measuring techniques include interferometry. Schlieren, and shadowgraph techniques. These techniques. however, have problems with light dissipation. The present method and sensor utilizes a pencil beam of energy which is passed through a transparent aperture in a flow inlet in a time-sequential manner so as to alter the energy beam. The altered beam or its effects are processed and can be studied to reveal information about flow through the inlet which can in turn be used for engine control.

Adamovsky, Grigory↗
NASA NTRS1975

Investigation of the unsteady pressure distribution on the blade of an axial flow fan

A major source of the noise generated by high bypass ratio aircraft fan engines is the unsteady pressures (forces and moments) acting on the fan blades. These unsteady pressures are the result of the interaction of the blades with the wakes of upstream blade rows, inlet flow distortions, and inlet turbulence. An experimental system was developed which will permit the measurement of the unsteady pressure distributions; a series of experiments were conducted to investigate these effects, and the results are compared with predictions from existing theoretical analyses.

Henderson, R. E.↗
NASA NTRS1986

Particle dispersion in confined turbulent swirling flows

This paper reports a numerical investigation of confined swirling flows of gas-particle mixtures. A recently developed two-fluid, multiple-scale mixing model is applied to study the influence of particles on the intensity of the reverse flows of the gas phase and the effects of swirl on the particle dispersion in an annular expanding chamber under isothermal condition. The calculations were made for different swirl strength of injection of the annular jet into the mixing chamber. Results agree well qualitatively with experimental information available. It is also found that the calculated flow fields depend heavily on the prescription of the inlet flow conditions.

Chen, C. P.↗
NASA NTRS1987

Endwall heat transfer in the junction region of a circular cylinder normal to a flat plate at 30 and 60 degrees from stagnation point of the cylinder

The objective of this experimental study was to investigate the influence of horseshoe vortex on the heat transfer on a flat plate near the base of a protruding cylinder. The partial shock reflection technique was used to produce the flow Mach number of 0.14 which simulated the mean inlet flow Mach number for the first stage vanes of the turbine after combustor. Fast response thin-film platinum heat gages were used to measure the heat transfer flux for radial distances of 0.75, 0.875, 1.0, 1.125 cylinder diameter. For a low Reynolds number of 20,000, r/D = 0.75, and angular location from the stagnation point = 60 deg, the maximum increase in the heat transfer rate with the cylinder was observed to be approximately 460 percent greater than without the cylinder. On the other hand, the increase in the heat flux for a high Reynolds number of 300,000 was approximately 70 percent greater. For the heat gages located along 30 deg and 60 deg angular locations from the stagnation point, the strong effect of the horseshoe vortex was observed in the junction region. The increase in the heat transfer rate depended on the type of boundary layer and on the boundary layer thickness ahead of the cylinder.

Nagamatsu, H. T.↗
NASA NTRS2013

Fully Integrated, Miniature, High-Frequency Flow Probe Utilizing MEMS Leadless SOI Technology

This work focused on developing, fabricating, and fully calibrating a flowangle probe for aeronautics research by utilizing the latest microelectromechanical systems (MEMS), leadless silicon on insulator (SOI) sensor technology. While the concept of angle probes is not new, traditional devices had been relatively large due to fabrication constraints; often too large to resolve flow structures necessary for modern aeropropulsion measurements such as inlet flow distortions and vortices, secondary flows, etc. Mea surements of this kind demanded a new approach to probe design to achieve sizes on the order of 0.1 in. (.3 mm) diameter or smaller, and capable of meeting demanding requirements for accuracy and ruggedness. This approach invoked the use of stateof- the-art processing techniques to install SOI sensor chips directly onto the probe body, thus eliminating redundancy in sensor packaging and probe installation that have historically forced larger probe size. This also facilitated a better thermal match between the chip and its mount, improving stability and accuracy. Further, the leadless sensor technology with which the SOI sensing element is fabricated allows direct mounting and electrical interconnecting of the sensor to the probe body. This leadless technology allowed a rugged wire-out approach that is performed at the sensor length scale, thus achieving substantial sensor size reductions. The technology is inherently capable of high-frequency and high-accuracy performance in high temperatures and harsh environments.

Ned, Alex↗