Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “IGNITION LIMIT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Effects of Ignition and Injection Perturbation under Lean and Dilute GDI Engine Operation

Turbocharged gasoline direct injection (GDI) engines are quickly becoming more prominent in light-duty automotive applications because of their potential improvements in efficiency and fuel economy. While EGR dilute and lean operation serve as potential pathways to further improve efficiencies and emissions in GDI engines, they also pose challenges for stable engine operation. Tests were performed on a single-cylinder research engine that is representative of current automotive-style GDI engines. Baseline cases were performed under steady-state operating conditions where combustion phasing and dilution levels were varied to determine the effects on indicated efficiency and combustion stability. Sensitivity studies were then carried out by introducing binary low-high perturbation of spark timing and injection duration on a cycle-by-cycle basis under EGR dilute and lean operation to determine dominant feedback mechanisms. Ignition perturbation was phased early/late of MBT timing, and injection perturbation was set fuel rich/lean of the given air-to-fuel ratio. COVIMEP was used to define acceptable operation limits when comparing different perturbation cases. Overall sensitivity data shows COVIMEP is more sensitive to injection perturbation over ignition perturbation. This is because of the greater effect injection perturbation has on combustion phasing, ignition delay, and combustion duration.

Wallner, Thomas↗

DNS of spark ignition and edge flame propagation in turbulent droplet-laden mixing layers

A parametric study of forced ignition at the mixing layer between air and air carrying fine monosized fuel droplets is done through one-step chemistry direct numerical simulations to determine the influence of the size and volatility of the droplets, the spark location, the droplet-air mixing layer initial thickness and the turbulence intensity on the ignition success and the subsequent flame propagation. The propagation is analyzed in terms of edge flame displacement speed, which has not been studied before for turbulent edge spray flames. Spark ignition successfully resulted in a tribrachial flame if enough fuel vapour was available at the spark location, which occurred when the local droplet number density was high. Ignition was achieved even when the spark was offset from the spray, on the air side, due to the diffusion of heat from the spark, provided droplets evaporated rapidly. Large kernels were obtained by sparking close to the spray, since fuel was more readily available. At long times after the spark, for all flames studied, the probability density function of the displacement speed was wide, with a mean value in the range 0.55-0.75S{sub L}, with S{sub L} the laminar burning velocity of a stoichiometric gaseous premixed flame. This value is close to the mean displacement speed in turbulent edge flames with gaseous fuel. The displacement speed was negatively correlated with curvature. The detrimental effect of curvature was attenuated with a large initial kernel and by increasing the thickness of the mixing layer. The mixing layer was thicker when evaporation was slow and the turbulence intensity higher. However, high turbulence intensity also distorted the kernel which could lead to high values of curvature. The edge flame reaction component increased when the maximum temperature coincided with the stoichiometric contour. The results are consistent with the limited available experimental evidence and provide insights into the processes associated with ignition of practical spray flames. (author)

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A shock tube study of ignition delay times in diluted methane, ethylene, propene and their blends at elevated pressures

Ignition delay times (IDT) of small hydrocarbons at elevated pressures provide a valuable constraint for the refinement of the core small-hydrocarbon sub-mechanisms used in all combustion kinetics. Current knowledge of these core mechanisms is based largely on low-pressure data, with only limited high-pressure data available. To remedy this, here the present study focuses on ignition delay times in methane, ethylene, propene and their blends at elevated pressures. IDT measurements were performed in 4% O 2 , balance Ar mixtures, over the temperature range of 950–1800 K, at pressures of 14–60 atm and equivalence ratios of 1 and 2. IDT was determined from recorded sidewall pressure, OH* emission measurements and fuel time-histories measured using laser absorption at 3.39 μm. These measurements extend the test conditions of earlier studies, with the advantage that they have all been performed at similar conditions and with the same facility and should provide a uniform set of kinetics targets for the evaluation of core small-hydrocarbon mechanisms. This dataset also allowed the temperature variation of the pressure and equivalence ratio scaling for methane and ethylene IDT to be investigated.

42 ENGINEERING↗

Three-dimensional modeling and hydrodynamic scaling of National Ignition Facility implosions

The goal of an inertially confined, igniting plasma on the National Ignition Facility (NIF) [M. L. Spaeth, Fusion Sci. Technol. 69, 25 (2016)] remains elusive. However, there is a growing understanding of the factors that appear to be limiting current implosion performance. And with this understanding, the question naturally arises: What conditions will ultimately be required to achieve ignition, either by continuing to improve the quality of current implosions, or by hydrodynamically scaling those implosions to larger driver energies on some future facility? Given the complexity of NIF implosions, answering this question must rely heavily on sophisticated numerical simulations. In particular, those simulations must respect the three-dimensionality of real NIF implosions and also resolve the wide range of scales for the many perturbation sources that degrade them. This prospectus article reviews the current state of detailed modeling of NIF implosions, the scaling to ignition from recent experiments that that modeling implies, and areas for future improvements in modeling technique that could increase understanding and further enhance predictive capabilities. Furthermore, given the uncertainties inherent in any extrapolation, particularly for a process as nonlinear as ignition, there will be no definitive answer on the requirements for ignition until it is actually demonstrated experimentally. However, with continuing improvements in modeling technique and a growing experience base from NIF, the requirements for ignition are becoming clearer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

What Machine Learning Can and Cannot Do for Inertial Confinement Fusion

Machine learning methodologies have played remarkable roles in solving complex systems with large data, well-defined input–output pairs, and clearly definable goals and metrics. The methodologies are effective in image analysis, classification, and systems without long chains of logic. Recently, machine-learning methodologies have been widely applied to inertial confinement fusion (ICF) capsules and the design optimization of OMEGA (Omega Laser Facility) capsule implosion and NIF (National Ignition Facility) ignition capsules, leading to significant progress. As machine learning is being increasingly applied, concerns arise regarding its capabilities and limitations in the context of ICF. ICF is a complicated physical system that relies on physics knowledge and human judgment to guide machine learning. Additionally, the experimental database for ICF ignition is not large enough to provide credible training data. Most researchers in the field of ICF use simulations, or a mix of simulations and experimental results, instead of real data to train machine learning models and related tools. They then use the trained learning model to predict future events. This methodology can be successful, subject to a careful choice of data and simulations. However, because of the extreme sensitivity of the neutron yield to the input implosion parameters, physics-guided machine learning for ICF is extremely important and necessary, especially when the database is small, the uncertain-domain knowledge is large, and the physical capabilities of the learning models are still being developed. In this work, we identify problems in ICF that are suitable for machine learning and circumstances where machine learning is less likely to be successful. This study investigates the applications of machine learning and highlights fundamental research challenges and directions associated with machine learning in ICF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Octane Requirements of Lean Mixed-Mode Combustion in a Direct-Injection Spark-Ignition Engine

Here, this study investigates the octane requirements of a hybrid flame propagation and controlled autoignition mode referred to as mixed-mode combustion (MMC), which allows for strong control over combustion parameters via a spark-initiated deflagration phase. Due to the throughput limitations associated with both experiments and 3-D computational fluid dynamics calculations, a hybrid 0-D and 1-D modeling methodology was developed, supported by experimental validation data. This modeling approach relied on 1-D, two-zone engine simulations to predict bulk in-cylinder thermodynamic conditions over a range of engine speeds, compression ratios, intake pressures, trapped residual levels, fueling rates, and spark timings. Those predictions were then transferred to a 0-D chemical kinetic model, which was used to evaluate the autoignition behavior of fuels when subjected to temperature–pressure trajectories of interest. Finally, the predicted autoignition phasings were screened relative to the progress of the modeled deflagration-based combustion in order to determine if an operating condition was feasible or infeasible due to knock or stability limits. The combined modeling and experimental results reveal that MMC has an octane requirement similar to modern stoichiometric spark-ignition engines in that fuels with high research octane number (RON) and high octane sensitivity (S) enable higher loads. Experimental trends with varying RON and S were well predicted by the model for 1000 and 1400 rpm, confirming its utility in identifying the compatibility of a fuel’s autoignition behavior with an engine configuration and operating strategy. However, the model was not effective in predicting (nor designed to predict) operability limits due to cycle-to-cycle variations, which experimentally inhibited operation of some fuels at 2000 rpm. Putting the operable limits and efficiency from MMC in the context of a state-of-the-art engine, the MMC showed superior efficiencies over the range investigated, demonstrating the potential to further improve fuel economy.

33 ADVANCED PROPULSION SYSTEMS↗

Ignition and subsequent flame spread over a thin cellulosic material

Both ignition and flame spread on solid fuels are processes that not only are of considerable scientific interest but that also have important fire safety applications. Both types of processes, ignition and flame spread, are complicated by strong coupling between chemical reactions and transport processes, not only in the gas phase but also in the condensed phase. In most previous studies, ignition and flame spread were studied separately with the result that there has been little understanding of the transition from ignition to flame spread. In fire safety applications this transition is crucial to determine whether a fire will be limited to a localized, temporary burn or will transition into a growth mode with a potential to become a large fire. In order to understand this transition, the transient mechanisms of ignition and subsequent flame spread must be studied. However, there have been no definitive experimental or modeling studies, because of the complexity of the flow motion generated by buoyancy near the heated sample surface. One must solve the full Navier-Stokes equations over an extended region to represent accurately the highly unstable buoyant plume and entrainment of surrounding gas from far away. In order to avoid the complicated nature of the starting plume problem under normal gravity, previous detailed radiative ignition models were assumed to be one-dimensional or were applied at a stagnation point. Thus, these models cannot be extended to include the transition to flame spread. The mismatch between experimental and calculated geometries means that theories cannot be compared directly with experimental results in normal gravity. To overcome the above difficulty, theoretical results obtained without buoyancy can be directly compared with experimental data measured in a microgravity environment. Thus, the objective of this study is to develop a theoretical model for ignition and the transition to flame spread and to make predictions using the thermal and chemical characteristics of a cellulosic material which are measured in normal gravity.

Nakabe, Kazuyoshi↗

Polar-drive implosions on OMEGA and the National Ignition Facility

Polar-drive (PD) experiments on the OMEGA [Boehly et al., Opt. Commun. 133, 495 (1997)] laser are described. Continuous pulse shapes, where a low-power foot is followed by a rise to the main pulse, and triple-picket pulse shapes, where three pickets precede the main pulse, are used to irradiate warm plastic shell capsules. Both of these pulse shapes set the target on a low, ignition-relevant adiabat of ∼3.5. The areal density is modeled very well in these implosions indicating that shock timing is well modeled in PD geometry. It is shown that the symmetry can be predictably varied by changing the beam pointings. Symmetry is also well reproduced across the two pulse shapes. Limitations of OMEGA experiments are discussed. Preliminary designs for PD implosion experiments on the NIF, with the goal of addressing ignition-relevant issues for PD, including symmetry are presented.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The National Ignition Facility modular Kirkpatrick-Baez microscope

Current two-dimensional X-ray imaging at the National Ignition Facility (NIF) uses time resolved pinhole cameras with ∼10-25 μm pinholes. This method has limitations in the smallest resolvable features that can be imaged with reasonable photon statistics for inertial confinement fusion (ICF) applications. ICF sources have a broadband self-emission spectrum that causes the pinhole images obtained, through thin foil filters, to contain a similarly broadband spectrum complicating the interpretation of structure in the source. In order to study phenomena on the scale of ∼5 μm, such as dopant mix in the ICF capsule, a narrow energy band, higher spatial resolution microscope system with improved signal/noise has been developed using X-ray optics. Utilizing grazing incidence mirrors in a Kirkpatrick-Baez microscope (KBM) configuration [P. Kirkpatrick and A. V. Baez, J. Opt. Soc. Am. 38, 766–774 (1948)], an X-ray microscope has been designed and fielded on NIF with four imaging channels. The KBM has ∼12 × magnification, <8 μm resolution, and higher throughput in comparison to similar pinhole systems. The first KBM mirrors are coated with a multilayer mirror to allow a “narrow band” energy response at 10.2 keV with ΔE ∼ 3 keV. By adjusting the mirror coating only, the energy response can be matched to the future experimental requirements. Several mirror packs have been commissioned and are interchangeable in the diagnostic snout.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Counterintuitive Catalytic Reactivity of the Aluminum Oxide “Passivation” Shell of Aluminum Nanoparticles Facilitating the Thermal Decomposition of exo -Tetrahydrodicyclopentadiene (JP-10)

High energy density aluminum nanoparticles (AlNP) have been at the center of attention as additives to hydrocarbon jet fuels like exo-tetrahydrodicyclopentadiene (JP-10, C 10 H 16 ) aiming at a superior performance of volume-limited air-breathing propulsion systems. However, a fundamental understanding of the ignition and combustion chemistry of JP-10 in presence of AlNPs has been elusive. Exploiting an isomer-selective comprehensive identification of the decomposition products in a newly designed high temperature chemical microreactor coupled to vacuum ultraviolet photoionization, we reveal an active low temperature heterogeneous surface chemistry commencing at 650 K involving the alumina (Al 2 O 3 ) shell. Contrary to textbook knowledge of an “inactive alumina surface”, this unconventional reactivity, where oxygen is transferred from alumina to JP-10, leads to generating cyclic, oxygenated organics like phenol (C 6 H 5 OH) and 2,4-cyclopentadiene-1-one (C 5 H 4 O) - key tracers of an alumina-mediated interfacial chemistry. Furthermore, this counterintuitive reactivity transforms our knowledge on the (catalytic) processes of alumina-coated AlNPs on the molecular level.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Using VISAR to assess the M-band isotropy in hohlraums

In laser based radiation flow experiments, drive variability can often overwhelm the physics sensitivity that one seeks to quantify. Hohlraums can help by providing a more symmetrized, Planckian-like source. However, at higher temperatures, the hohlraum’s actual emission can deviate significantly from a truly blackbody, Lambertian source. At the National Ignition Facility (NIF), Dante provides the best quantification of hohlraum output. Unfortunately, limited diagnostic access coupled with NIF’s natural symmetry does not allow for Dante measurements at more than two angles. As part of the CEPHEUS campaign on NIF, proof-of-principle experiments to better quantify the gold M-band isotropy were conducted. These experiments positioned beryllium/aluminum mirrors at differing angles, offset from the hohlraum. Filtering removes the thermal emission of the hohlraum and the remaining M-band radiation is preferentially absorbed in the aluminum layer. The subsequent hydrodynamic motion is measured via VISAR. Although indirect, this M-band measurement can be made at any angle.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

A study of space charge induced non-linearity in the Single Line Of Sight camera

We report a new generation of gated x-ray detectors at the National Ignition Facility has brought faster, enhanced imaging capabilities. Their performance is currently limited by the amount of signal they can be operated with before space charge effects in their electron tube start to compromise their temporal and spatial response. We present a technique to characterize this phenomenon and apply it to a prototype of such systems, the Single Line Of Sight camera. Results of this characterization are used to benchmark Particle In Cell simulations of the electrons drifting inside the detector, which are found to well reproduce experimental data. These simulations are then employed to predict the optimum photon flux to the camera, with the goal to increase the quality of the images obtained on an experimental campaign while preventing the appearance of deleterious effects. They also offer some insight into some of the improvements that can be brought to the new pulse-dilation systems being built at Lawrence Livermore National Laboratory

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Grid resolution requirement of chemical explosive mode analysis for large eddy simulations of premixed turbulent combustion

Full Article Figures & data References Citations Metrics Reprints & Permissions Read this article Abstract The grid resolution requirement for trustworthy Chemical Explosive Mode Analysis (CEMA) in Large Eddy Simulation (LES) of premixed turbulent combustion is proposed. Explicit filtering, to emulate the effect of the LES filter, is applied to one-dimensional laminar flame and three-dimensional planar turbulent flames across a wide range of Karlovitz numbers (5 - 239). The identification of the flame front by CEMA is found relatively insensitive to the cell size (Δ), while the combustion mode identification shows more significant sensitivity. Specifically, increasing Δ falsely enhances the auto-ignition and local extinction modes and suppresses the diffusion-assisted mode. Limited dependence of the CEMA performance on the turbulent combustion regime (Karlovitz number) is observed. A simple grid size criterion for reliable CEMA mode identification in LES is proposed as Δ ≲ δ L /2; The criterion can be relaxed to Δ ≲ δ L in the laminar flame limit. Furthermore, theoretical analysis is conducted on an idealised chemistry-diffusion system. The effects of the filtering process and turbulence on the local combustion mode are demonstrated, which is consistent with the numerical observations. Further, by incorporating turbulent combustion models in CEMA, potential improvement in identifying local combustion modes can be expected.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Thermal Cooling Limits of Sbotaged Spent Fuel Pools

To develop the understanding and predictive measures of the post “loss of water inventory” hazardous conditions as a result of the natural and/or terrorist acts to the spent fuel pool of a nuclear plant. This includes the thermal cooling limits to the spent fuel assembly (before the onset of the zircaloy ignition and combustion), and the ignition, combustion, and the subsequent propagation of zircaloy fire from one fuel assembly to others

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Methanol Droplet Extinction in Oxygen/Carbon-dioxide/Nitrogen Mixtures in Microgravity: Results from the International Space Station Experiments

Motivated by the need to understand the flammability limits of condensed-phase fuels in microgravity, isolated single droplet combustion experiments were carried out in the Combustion Integrated Rack Facility onboard the International Space Station. Experimental observations of methanol droplet combustion and extinction in oxygen/carbon-dioxide/nitrogen mixtures at 0.7 and 1 atmospheric pressure in quiescent microgravity environment are reported for initial droplet diameters varying between 2 mm to 4 mm in this study.The ambient oxygen concentration was systematically lowered from test to test so as to approach the limiting oxygen index (LOI) at fixed ambient pressure. At one atmosphere pressure, ignition and some burning were observed for an oxygen concentration of 13% with the rest being nitrogen. In addition, measured droplet burning rates, flame stand-off ratios, and extinction diameters are presented for varying concentrations of oxygen and diluents. Simplified theoretical models are presented to explain the observed variations in extinction diameter and flame stand-off ratios.

Nayagam, Vedha↗

Development and Testing of a Green-Propellant Micro-Hybrid Thruster with Electrostatic Ignition

As early as 1937 German scientists at Peenemunde experimented with highly unstable fuel blends of nitrous oxide (N2O) and ethanol. These early tests mostly resulted in explosions and destroyed rocket engines. More recently several companies have developed experimental nitrous oxide fuel blends (NOFB) with Isp exceeding 300 sec. Although NOFBx has recently been cleared for tests on the International Space Station, this propellant remains highly experimental and has not been cleared for commercial transport by the US DOT. Recent work by Karabeyoglu et al. has raised concerns about the safety risks of mixing hydrocarbons with N2O. Liquid oxidizer/fuel blends are highly explosive and require extreme care in transport and servicing. By adding small amounts of a liquid organic fuel such as alcohol or a hydrocarbon, the odds of an explosive decomposition event are significantly increased.iv The proposed solution mitigates the explosion hazards of NOFB by separating the oxidizer from the hydrocarbon fuel formed as of a small cylindrical section of ABS thermoplastic. As N2O vapor flows across the grain segment, current enters a 1000 VDC high-tension lead in the ABS fuel grain and produces an inductive spark that vaporizes a small amount of the material. The ablated fuel vapor plus residual energy from the spark seed a localized exothermic N2O dissociation that produces sufficient heat to initiate combustion. The process is also effective when gaseous oxygen is used. A low TRL (2-3) prototype demonstrating the feasibility of controlled hydrocarbon-seeding was recently tested at Utah State University.v The unit features a miniature 2.5 cm ABS fuel grain fabricated using a Stratasys Dimension 3-D printer. The 9-N thruster was pulse-fired up to 27 consecutive times on a single ABS grain segment. Ignition was achieved by as little as 12-15 Joules energy input. This value is contrasted with the typical 30-minute pre-heat requirement for the ECAPS LMP-103S ADN-based monopropellant, requiring an energy input of 14,850 Joules for catalytic dissociation. The hydrocarbon-seeded micro-hybrid was also adapted as a non-pyrotechnic ignitor for a 900 N (200-lbf) thrust hybrid motor. The motor was successfully ignited 4 consecutive times with no hardware swaps or propellant additions. The amount of ABS seed material that can be fit into the injector cap is the only limit to the number of available repeat firings. This series of tests marks the first time a hybrid motor was ever ignited by other than a solid-propellant pyrotechnic charge or bi-propellant flame ignitor. Nitrous oxide hybrid motors are typically difficult to ignite and usually require multiple solid-propellant charges to initiate combustion, so this nonpyrotechnic ignition is a significant accomplishment. The controlled hydrocarbon-seeding approach is fundamentally different from all other green propellant solutions offered by the aerospace industry. Although the proposed system is more correctly a hybrid technology; the system retains all the simple features of a monopropellant design. To date no optimization study has been performed to identify the best grain geometry for electrostatic ignition. Fortunately, because the grain segments are fabricated using rapid-prototyping technology, changing the grain geometry is as simple as modifying the 3-D printer CAD-file. Vacuum Isp exceeding 270 seconds has been demonstrated (Ref v), a value significantly higher than those offered by competing green monopropellant options. The propellants of choice, N2O/GOX and ABS are 100% non-toxic, non-explosive, and environmentally benign. Because the inert oxidizer and fuel components are mixed only within the combustion chamber, the system retains the inherent safety of a hybrid rocket and can be piggy-backed as a secondary payload with no overall mission risk increase to the primary payload, an excellent characteristic for secondary launch systems.

Whitmore, Stephen A.↗

Collision of plane thermonuclear detonation waves in a preliminarily compressed DT mixture

The paper deals with a one-dimensional problem on symmetric irradiation of a plane DT fuel layer with a thickness 2H and density ρ{sub 0} ⩽ 100ρ{sub s} (where ρ{sub s} is the density of the DT fuel in the solid state at atmospheric pressure and a temperature of 4 K) by two identical monoenergetic proton beams with a kinetic energy of 1 MeV, an intensity of 10{sup 19} W/cm{sup 2}, and a duration of 50 ps. The problem is solved in the framework of one-fluid two-temperature hydrodynamic model that takes into account the equation of state for hydrogen, electron and ion heat conductivities, kinetics of the DT reaction, plasma self-radiation, and plasma heating by α-particles. The irradiation of the fuel results in the appearance of two counterpropagating detonation waves to the fronts of which rarefaction waves are adjacent. The efficiency of the DT reaction after the collision (reflection from the plane of symmetry) of the detonation waves depends on the spatial homogeneity of thermodynamic functions between the fronts of the reflected detonation waves. At Hρ{sub 0} ≈ 1 g/cm{sup 2}, the gain factor is G ≈ 200, whereas at Hρ{sub 0} ≈ 5 g/cm{sup 2}, it is G > 2000. As applied to a cylindrical target that is ignited from ends and in which the cylinder with the fuel is surrounded by a heavy magnetized shell, the obtained values of the burn-up and gain factors are maximum possible. To estimate the ignition energy E{sub ig} of a cylindrical target by using solutions to the one-dimensional problem, a quasi-one-dimensional model is developed. The model assumes that the main mechanism of target ignition is fuel heating by α-particles. The trajectories of α-particles are limited by a cylindrical surface with a given radius, which is a parameter of the model and is identified with the fuel radius in the target and the radii of the irradiating proton beams. This model reproduces the well-known theoretical dependence E{sub ig} ∼ ρ{sub 0}{sup −2} and yields E{sub ig} = 160 kJ as a lower estimate of the ignition energy for ρ{sub 0} = 100ρ{sub s} ≈ 22 g/cm{sup 3}.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗