SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Poster for concluding seed LDRD project on Moderate High Pressure X-ray Radiation-Induced Degradation of Persistent Poly- and Perfluoroalkyl Substances (PFAS). Project Number: 23P1-79-010FP.
Self-propagating exothermic reactions, for instance in the nickel-aluminum (Ni-Al) system, have been widely studied to create high performance intermetallic compounds or for in-situ welding. Their easy ignition once the phase spacing is reduced below the micron scale, makes top-down methods like high-energy ball milling, ideal to fabricate such reactive nanostructures. A major drawback of ball milling is the need of a sintering step to form bulk pieces of the reactive material. However, this is not possible, as the targeted reactions would already proceed. Therefore, we investigate the ability of high pressure torsion as an alternative process, capable to produce bulk nanocomposites from powder mixtures. Severe straining of powder mixtures with a composition of 50 wt% Ni and 50 wt% Al enables fabrication of self-reactive bulk samples with microstructures similar to those obtained from ball milling or magnetron sputtering. Additionally, samples deformed at ambient temperature are highly reactive and can be ignited significantly below the Al melting point, finally predominantly consisting of Al 3 Ni 2 and Al 3 Ni, independent of the applied strain. Although the reaction proceeds first at the edge of the disk, the strain gradient present in the disks does not prevent reaction of the whole sample.
Resonant inelastic X-ray scattering (RIXS) is increasingly playing a significant role in studying highly correlated systems, especially since it was proven capable of measuring low-energy magnetic excitations. However, despite high expectations for experimental evidence of novel magnetic phases at high pressure, unequivocal low-energy spectral signatures remain obscured by extrinsic scattering from material surrounding the sample in a diamond anvil cell (DAC): pressure media, Be gasket and the diamond anvils themselves. A scattered X-ray collimation based medium-energy resolution (~100 meV) analyzer system for a RIXS spectrometer at the Ir L 3 -absorption edge has been designed and built to remediate these difficulties. Due to the confocal nature of the analyzer system, the majority of extrinsic scattering is rejected, yielding a clean low-energy excitation spectrum of an iridate Sr 2 IrO 4 sample in a DAC cell. Finally, the energy resolution of different configurations of the collimating and analyzing optics are discussed.
Plastic strain-induced phase transformations (PTs) and chemical reactions under high pressure are broadly spread in modern technologies, friction and wear, geophysics, and astrogeology. However, because of very heterogeneous fields of plastic strain $E$ p and stress σ tensors and volume fraction c of phases in a sample compressed in a diamond anvil cell (DAC) and impossibility of measurements of σ and $E$ p , there are no strict kinetic equations for them. Here, we develop a kinetic model, finite element method (FEM) approach, and combined FEM-experimental approaches to determine all fields in strongly plastically predeformed Zr compressed in DAC, and specific kinetic equation for α-ω PT consistent with experimental data for the entire sample. Since all fields in the sample are very heterogeneous, data are obtained for numerous complex 7D paths in the space of 3 components of the plastic strain tensor and 4 components of the stress tensor. Kinetic equation depends on accumulated plastic strain (instead of time) and pressure and is independent of plastic strain and deviatoric stress tensors, i.e., it can be applied for various above processes. Our results initiate kinetic studies of strain-induced PTs and provide efforts toward more comprehensive understanding of material behavior in extreme conditions.
Direct numerical simulations of binary-species temporal boundary layers at high pressure are performed. The main objective is to investigate the influence of the Soret effect on flow physics of binary-species boundary layers where the fluid has a uniform composition. The working fluid is a mixture of 25 % methane and 75 % nitrogen in mass fraction. Although the fluid composition is uniform at the initial condition, the mass fraction of methane increases near the wall when the wall temperature is hotter than the free stream temperature, whereas it decreases when the wall temperature is colder. The non-uniform mass fraction indicates that the uphill diffusion occurs near the wall. Investigation of fluctuations of the mass fraction reveals that the mass fraction fluctuates in the whole boundary layer, indicating that the uphill diffusion occurs even far from the wall. Examination of the species-mass diffusion balance for mean flow fields clarified that the Soret effect flux becomes large near the wall, and the large flux causes the non-uniform profile of the mass fraction near the wall.
In this study, we investigate the toughness and resistance to tear of thin-wall high-pressure die-cast (HPDC) aluminum alloys in two different orientations following the implementation of friction stir processing (FSP). The FSP technique was applied to two different HPDC Al-Si alloys: the recyclable-grade, high iron, A380 alloy and the premium-quality, low iron, Aural-5 alloy. Our findings reveal significant tear resistance and strength enhancements for both alloys after FSP modification. Specifically, FSPed A380 alloy requires 126% higher energy to tear, and it has 49% higher tear strength than the HPDC counterpart. Similarly, the tear energy and tear strength of the Aural-5 alloy witness enhancements of 69% and 21%, respectively. In conclusion, these results highlight the potential of FSP as a viable method for augmenting the mechanical properties of HPDC aluminum alloys, thereby opening up new avenues for their utilization in diverse engineering applications for crack obstruction.
Components for a transformative, high pressure, intermediate temperature solid oxide fuel cell (SOFC) and premixed compression ignition (PCI) engine system were developed. The resulting system is a 1 MWe natural gas fueled hybrid SOFC and reciprocating internal combustion engine system capable of achieving over 70% electrical efficiency at a cost of $0.87/W. To achieve 70% electric efficiency, the SOFC system operates at 80% fuel utilization; however, when operating at this high level of fuel utilization, fuel to the engine (anode tailgas) is extremely dilute. Accordingly, a substantial portion of the effort focused on development and assessment of the combustion strategy capable of consuming this dilute fuel mixture. The engine testing effort showed that pre-chamber assisted compression ignition provides the best combination of controllability, efficiency and emissions. The engine experiments showed that high efficiency combustion can be achieved with near zero criteria pollutants. It is likely that the engine system could operate with minimal aftertreatment requirements, reducing complexity, cost, and precious metal usage. System level modeling was used to assess the overall efficiency, determine cost and efficiency tradeoffs, and demonstrate the potential to perform load following with the hybrid system. Finally, advanced manufacturing was used to demonstrate the potential to fabricate heat exchangers needed for the hybrid system from low chromium materials, which addresses the issue of chromium poisoning of the SOFC stack material.
In this work we study the high-pressure melting behavior of titanium using laser-driven shock compression with in situ femtosecond x-ray diffraction and molecular-dynamics simulations based on a machine-learned interatomic potential. The MD simulations predict the solid-liquid coexistence on the Hugoniot in the ∼111−124GPa range. Experimentally, we observe the first evidence of liquid at 86 GPa. We also observe pronounced microstructural changes with pressure, with strong grain refinement associated with the emergence of liquid, within the solid-liquid coexistence (∼110−126GPa). Above 126 GPa, we observe the persistence of residual levels of highly textured crystalline Ti to ∼180GPa, well above the expected melt completion pressure. We discuss the accuracy that current laser-shock experimental platforms have at determining the melt onset and completion pressures.
We have studied the laser-initiated deflagration of nitromethane (CH 3 NO 2 ) under high static pressure in the diamond anvil cell. Time-resolved images of the deflagrations have been obtained using intensified CCDs (ICCD). In contrast with previous work, we rely on spontaneous emission from the reaction, rather than changes in the speckle pattern produced by artificial illumination of the sample. Furthermore, as opposed to the 1D records obtained previously with streak cameras, ICCDs permit imaging of the burn in two dimensions providing the ability to directly observe anisotropic deflagration behavior. Here, we report several examples of this behavior and discuss its possible origins. We have also investigated the products of the reaction using Raman spectroscopy. At pressures below 25 GPa, the burn product is observed to be opaque and has a Raman spectrum consistent with a carbonaceous soot. At pressures above 25 GPa, the burn product is observed to be transparent (consistent with earlier reports) and its Raman spectrum reveals the presence of molecular N 2 and a nitrogen-carbonate species. The latter species can be recovered to ambient pressure and has a Raman spectrum consistent with ammonium carbonate or ammonium bicarbonate. To aid interpretation of the Raman spectra, measurements have also been made on the isotopologues CH 3 15 NO 2 and 13 CH 3 NO 2 . This work establishes the importance of advanced time-resolved imaging to reveal the details of deflagration under high pressure and further advances our understanding of the corresponding chemistry.
Nitrogen doped lutetium hydride has drawn global attention in the pursuit of room-temperature superconductivity near ambient pressure and temperature. However, variable synthesis techniques and uncertainty surrounding nitrogen concentration have contributed to extensive debate within the scientific community about this material and its properties. We used a solid-state approach to synthesize nitrogen doped lutetium hydride at high pressure and temperature (HPT) and analyzed the residual starting materials to determine its nitrogen content. High temperature oxide melt solution calorimetry determined the formation enthalpy of LuH 1.96 N 0.02 (LHN) from LuH 2 and LuN to be −28.4 ± 11.4 kJ/mol. Magnetic measurements indicated diamagnetism which increased with nitrogen content. Ambient pressure conductivity measurements observed metallic behavior from 5 to 350 K, and the constant and parabolic magnetoresistance changed with increasing temperature. High pressure conductivity measurements revealed that LHN does not exhibit superconductivity up to 26.6 GPa. We compressed LHN in a diamond anvil cell to 13.7 GPa and measured the Raman signal at each step, with no evidence of any phase transition. Despite the absence of superconductivity, a color change from blue to purple to red was observed with increasing pressure. Thus, our findings confirm the thermodynamic stability of LHN, do not support superconductivity, and provide insights into the origins of its diamagnetism.
To date, temperature and conductivity have many outstanding implications in extreme environments but are yet to be fully understood under high pressure and temperature dynamic conditions. Here, we introduce an approach to provide high quality electrical conductivity results under dynamic loading conditions. Emphasis is given to address the skin depth effect's influence in a dynamic loading experiment by using thin films. The thin film samples in this study were at least 100 times thinner than previous samples in dynamic electrical conductivity experiments, increasing the current density to its full potential across the sample's entire cross section. Consideration of the skin depth accounts for at minimum a 4× scaling factor to the final electrical conductivity result that has been neglected in previous dynamic electrical conductivity studies. We also obtained improved signal-to-noise ratio with custom diagnostics optimized for better electrical impedance matching. Furthermore, these considerations were applied to Sn to assess electrical conductivity at elevated pressure and temperature. The high signal-to-noise ratio with reduced skin depth influence results in Sn allowing observation of the conductivity changes related to solid-to-solid and solid-to-liquid phase transitions. Additionally, we calculate the Sn thermal conductivity using the Wiedemann-Franz law for our experiments and compare against thermal transport dependent temperature measurements from previous work.
Polyfluoroacrylate (PFA) is a hydrophobic and oleophobic polymer that is soluble in high pressure carbon dioxide (CO 2 ). In this study, the ability of PFA-CO 2 solutions to greatly reduce the apparent permeability of split or cracked Portland cement cylindrical samples is assessed. The apparent permeability values of confined samples were determined before and after treatment with PFA-CO 2 solutions. In four tests, PFA-CO 2 solutions were continuously displacing pure CO 2 from the cracked cement and the decrease in apparent permeability due to PFA adsorption and wettability alteration was monitored. The lowest apparent permeability cracked cement sample (81 nD) was completely sealed with a very small amount of solution. Samples with initial apparent permeabilities of 89 μD and 29.4 mD exhibited 92% and 99% reductions in permeability, respectively, before the experiments had to be stopped because of the excessively large increase in pressure drop. A 50% reduction in apparent permeability was observed with a 3.80 mD sample. Four other split cement samples (bound together with tape) with an initial apparent permeability in the 9.0–70 mD range were removed from the core holder and immersed in a PFA-CO 2 solution for 24 h to allow for PFA adsorption. Then the PFA-CO 2 solution was depressurized, allowing for the deposition of additional PFA from the solution within the crack as the pressure fell below the cloud point pressure of the PFA-CO 2 solution. These four samples were then confined again in a core holder and apparent permeability reductions of 29–93% were observed. Finally, results from these eight experiments indicates that the more substantial reductions in the nD – mD apparent permeability of the cracked cement correlated to lower initial crack permeability, higher PFA concentration, and slower injection rate of the PFA-CO 2 solution into the crack.
Abstract The high‐pressure behavior of bis(nitroxymethylisoxazolyl) furoxan (DNDIF) was studied at ambient temperature and pressures approaching 30 GPa by Raman spectroscopy and powder X‐ray diffraction. There was no evidence of a phase change observed over this pressure range, indicating that the ambient structure of DNDIF remains stable up to conditions similar to the detonation pressure of the material. Such findings suggest that this melt‐castable explosive may be used in the replacement of 2,4,6‐trinitrotoluene (TNT) in energetic formulations without the concern of uncontrolled polymorphism that might otherwise affect the performance and safety of the munition. Additionally, empirical understanding of the effect of different structural motifs in the crystal packing builds on understanding of what macroscale features are desirable for future materials and gets us closer to the design of future novel energetics.
A new experimental study reported behavior in a high-pressure carbon-sulfur-hydrogen system that has been interpreted by the authors as superconductivity at room temperature. The sudden change of electrical resistance at a critical temperature and the change of the R vs. T behavior with an applied magnetic field point to superconductivity. This is a very exciting study in one of the most important areas of science, hence, it is crucial for the community to investigate these findings and hopefully reproduce these results. In this paper, we present calculations that expand upon the arguments put forth, and offer some speculations about physical mechanisms that might explain the observed data. Here, we show that there are errors in the analysis presented in the experimental paper, and with the correct analysis, the reported R vs. T data significantly deviate from the expected behavior. In particular, the extremely sharp change in resistance at the superconducting transition is not consistent with a strongly type II superconductor.
Steadily rising demand for glider weight reduction has driven the development of vacuum-assisted high-pressure die-cast (HPDC) Al-alloys for automotive structural components. Aural-5 is a strontium-modified HPDC alloy utilizing manganese (Mn) to reduce die soldering, eliminating detrimental needle-shaped Fe-bearing ß-phase intermetallic and improving ductility. HPDC Aural-5 contains shrinkage porosity, dendrites with Al-Si eutectic colonies, externally solidified crystals (ESCs), shear-band structure, and large second-phase particulates. Porosity, ESCs and large second-phase particles work as crack initiation sites, negatively impacting tensile properties. In this study, friction stir processing (FSP) is employed for microstructural modification of a thin-walled HPDC Aural-5 by eliminating porosity and breaking down dendrites, second-phase particles, eutectic colonies, ESCs and shear-band structures to create wrought microstructure with homogenized particle distribution. Mechanical property characterization indicates ~30% and ~35% enhancement in yield strength and ductility and associated marked effects on ~69% improvement in tear toughness according to the ASTM B871 test.
In this study, the effects of mechanical grinding (G) assisted by endoglucanase (E) and high-pressure homogenization (H) post-treated cellulose nanofibrils (CNFs) and its film properties were investigated. Compared to only mechanical grinding, these two post-treatment processes improved the size uniformity of CNFs in width. Additionally, the crystallinity of GECNFs was increased by 4.3 % and the resulting film exhibited low oxygen permeability rate (6.33 mL/m 2 ·day). Moreover, the combination post-treatments of enzyme and homogenization improved the tensile strength and transparency of CNFs films from 132.31 MPa, 27.52 %– to 177.99 MPa, 61.75 %, respectively. Besides, a composite of acrylic resin ABPE-10 and GEHCNFs film under negative pressure improved the transparency (85.68 %) and water contact angle (104.11°) of film. This work also provides insight on the relationship between the CNFs morphology and their film properties, which can be used to improve the CNFs film performance and promote future applications of CNFs.
Non-hydrostatic high pressure X-ray diffraction is used to study the hardness of superhard ReB 2 nanocrystals. All nanocrystals show less plastic deformation under load than bulk ReB 2 , with the smallest nanocrystals showing the most enhancement.
High-pressure chemistry is known to inspire the creation of unexpected new classes of compounds with exceptional properties. In this paper, we employ the laser-heated diamond anvil cell technique for synthesis of a Dirac material BeN 4 . A triclinic phase of beryllium tetranitride tr-BeN 4 was synthesized from elements at similar to 85 GPa. Upon decompression to ambient conditions, it transforms into a compound with atomic-thick BeN 4 layers interconnected via weak van der Waals bonds and consisting of polyacetylene-like nitrogen chains with conjugated pi systems and Be atoms in square-planar coordination. Theoretical calculations for a single BeN 4 layer show that its electronic lattice is described by a slightly distorted honeycomb structure reminiscent of the graphene lattice and the presence of Dirac points in the electronic band structure at the Fermi level. The BeN 4 layer, i.e., beryllonitrene, represents a qualitatively new class of 2D materials that can be built of a metal atom and polymeric nitrogen chains and host anisotropic Dirac fermions.