Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GAS DISCHARGE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

High-rate heavy-ion tracking using MWPCs and PPACs with an Anti-Discharge Unit

This work reports on the development of two robust, heavy-ion beam tracking concepts operating at low pressure (< 15 Torr) for high rate applications (> 200 kHz). The first concept consists of a Multi-Wire Proportional Counter (MWPC) with a central anode consisting of 12 μm Au-plated Tungsten wires spaced 1 mm from each other. The anode grid is sandwiched between two segmented cathodes aligned orthogonally in the two dimensions for (x,y) particle localization. The second detector is a Parallel-Plate Avalanche Counter (PPAC) that uses the same readout geometry as the MWPC, but replaces the wire anode with a 150 nm silver layer deposited on both sides of a thin (< 1 mg/cm 2 ) polypropylene foil. Additionally, the bias circuitry for the PPAC anode central foil is equipped with an Anti-Discharge Unit (ADU) to prevent transitions from proportional operation to streamer formation, thereby avoiding damaging discharges. The localization capability of both detectors was tested with a low-rate alpha-particle source (241-Am). A position resolution of < 1 mm (FWHM) was achieved under stable, high-gas-gain (> 1000) operating conditions. Their performance in terms of detection efficiency as a function of the isotope charge (Z) was determined by irradiating the detectors with a cocktail beam (Z ≤ 15) with energy of ∼ 100 MeV/u. Full detection efficiency is maintained for all available fragments under optimal operational conditions (i.e., voltage bias). Full detection efficiency was achieved at rates above 200 kHz by irradiating the detectors with a 1 cm diameter 238 U beam at an energy of 143 MeV/u.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2024

Decomposition characteristics of C4F7N-based SF6-alternative gas mixtures

C4F7N [2,3,3,3-tetrafluoro-2-(trifluoromethyl)propanenitrile]/CO2 gas mixtures are being developed as an eco-friendly electrical insulator to replace SF6, the most potent greenhouse industrial gaseous dielectric. However, recent studies have reported complicated and often conflicting decomposition pathways for C4F7N/CO2 gas mixtures, which has raised concerns. In this work, the decomposition characteristics of C4F7N/CO2 gas mixtures were studied comprehensively by both designed computations and experiments. Computations were performed starting from fundamental propositions of C4F7N/CO2 decompositions, which were further experimentally verified by pyrolysis, long-term thermal aging with/without catalytic materials (industrial-grade molecular sieves 4A), and electrical decomposition by spark discharge. The results of both computations and experiments suggest that in an ideal thermal decomposition, C4F7N is likely to decompose into C2F6 and small fluoronitriles first at high temperatures. The generation of C3F6 and C2N2 from C4F7N thermal decomposition at lower temperatures appears because of the catalytic effect of incompatible materials, for example, the industrial-grade molecular sieves 4A that we tested. The electron impact dissociation of C4F7N plays an important role in C4F7N electrical decomposition, leading to additional formation of distinctive small molecules of CF4 and C2N2 of low concentrations. It was pointed out based on a real arcing test in a load disconnector that the decomposition of C4F7N gas mixtures in real applications will be at a much moderate and manageable rate than what was obtained from the highly accelerated laboratory tests presented in this work. The signatures of decomposition products extracted in this study provide invaluable guidance for developing decomposition-based diagnosis and fixation of decomposition byproducts toward SF6-free power grids.

Physics↗
DOE OSTI2022

Combined Cycle Integrated Thermal Energy Storage “CiTES” (Final Scientific/Technical Report)

The Phase I of this project confirmed the technical feasibility of a Combined Cycle integrated Thermal Energy Storage “CiTES” system, calculated the key performance parameters like power efficiency and costs, and proved its commercial value with full-year simulations for several US electricity markets with high degree of variable renewable generation and volatile hourly electricity prices. The core element of this project is the Electro Thermal Energy Storage (ETES) technology from Siemens Gamesa Renewable Energy GmbH, using thermally stable and inexpensive volcanic rocks as storage material and air as heat transfer medium. This technology is backed by more than 10 years of experience and a 440MMBTU (130MWh-th) pilot plant in Hamburg, Germany, which is in operation since 2019. The integration of this thermal storage in an existing combined cycle power plant (CCPP) is typical power plant technology without any major technology risks. It allows the storage of inexpensive renewable energy during times of surplus renewable generation and the discharge of this energy in times of high energy demand when the fossil plant is in operation. This supplements the fossil power generation with CO2-emission-free energy. The secondary effect of the CiTES system is that a small part of the stored thermal energy is used to keep the heat recovery steam generator (HRSG) and steam turbine (ST) of the combined cycle power plant in hot and ready-to-start condition. This enables the plant to start rapidly when fossil generation is required to satisfy demand as soon variable generation drops off in the evenings or during cloud cover and calm wind periods. Without pre-warming of the HRSG and ST, the CCPP would need several hours for a cold or warm start, burn a lot of gas and release high NOx emissions during start and wouldn’t be able to use the short times of high energy prices in an efficient or economical manner. The economic parameters of CiTES were determined by a full year “8760” simulation using a data set calculation for each of the hours of the year, and historical electricity and gas prices. For consistency, the simulations were focused on the pre-COVID year 2019. The financially most attractive markets were in the Energy Reliability Council of Texas (ERCOT) region, which allowed substantial value generation with arbitrage (charge with cheap energy during renewable surplus times and discharge when energy is needed and expensive). The improvement of flexibility with the CiTES system by pre-heating and warm-keeping of the CCPP allowed for additional power generation during short time periods when demand is high but renewable generation is down; when the hourly energy prices are highest in these markets. The simulations are based on 2019 data, when ERCOT had 27GW of installed photovoltaic (PV) and wind generation. They showed that the created revenue with the prototypically sized CiTES system of 1,000MMBTU (300MWh-th) falls a little bit short of what is expected from a commercially viable investment. The system has optimization opportunities for cost reduction and increased effectiveness which will be realized during a potential Phase II Pre-FEED study following this project. Furthermore, it is safe to assume that a lot of renewable generation capacity will be added all over the US in the coming years. As an example, ERCOT is predicting to more than double its renewable generation from 27GW in 2019 to a forecasted 63GW in 2023. This will increase the amount of renewable overproduction exponentially. This rapid increase of local overproduction and the need to curtail renewable generation is well documented by the California ISO (www.CAISO.com / managing oversupply). However, the simulations also revealed a weakness in the structure of the electricity markets in the US. More specifically, when electricity prices are very low and approaching negative levels, the owners of Variable Renewable Energy (VRE) will curtail a part of their facility to stabilize the price by reducing supply. This results in a situation in which storage facilities, which are integrated in existing fossil assets and don’t have the behind-the-meter benefit of a VRE, won’t be able to purchase low cost – otherwise curtailed – renewable energy off the grid. A special tariff, which motivates VRE owners to sell otherwise curtailed renewable energy to storage facilities (Hydrogen, thermal, pumped hydro, etc.) can solve this issue. The implementation of such a regulating tariff by Independent System Operators, thus avoiding renewable curtailment, is a pre condition for successful commercialization for renewable energy storage technologies. With this advancement of design and technology and improvements in the market environment, it can be expected that the Combined Cycle integrated Thermal Energy Storage proves itself as an important innovation to keep highly efficient, natural gas-based power generation economically successful and relevant for the power industry in the United States of America.

Wolf, Thorsten↗
DOE OSTI2025

Hydrogen from low-density polyethylene via nonthermal plasma: Effects of energy density and process parameters

Nonthermal plasma processes are promising for the modular valorization of plastic waste, especially into hydrogen and carbon materials, due to their high intensity, lack of reliance on catalysts or consumables, and suitability to be directly powered by electricity. We investigate the production of hydrogen from low-density polyethylene (LDPE) as a plastic waste model using streamer Dielectric Barrier Discharge (sDBD) plasma in nitrogen at atmospheric pressure. Here, we examine the effects of process energy density (energy input per unit of feedstock mass), feedstock mass, and plasma intensity (electric voltage) on plasma properties, hydrogen yield and energy efficiency via gas chromatography, optical emission spectroscopy, and electrical diagnostics, together with reactor-scale and nonlinear electric circuit modeling. The characteristic temperature of free electrons in the sDBD plasma is approximately 15000 K (1.3 eV), and that of gas species 10 times lower, demonstrating strong thermal non-equilibrium that can lead to molecular bond scission via charged species impact rather than direct heating. Experimental results show that higher energy density leads to greater hydrogen production and diminishing energy efficiency, and that higher plasma intensity and larger feedstock mass lead to greater hydrogen yield due to higher plasma temperatures and enhanced energy fluxes to the feedstock.

08 HYDROGEN↗
DOE OSTI2021

Study of vacuum ultraviolet emission in helium and helium/nitrogen mixtures

Helium is frequently used as a working medium for the generation of plasmas and is capable of energetic photon emissions. These energetic photon emissions are often attributed to the formation of helium excimer and subsequent photon emission. When the plasma device is exposed to another gas, such as nitrogen, this energetic photon emission can cause photoionization and further ionization wave penetration into the additional gas. Often ignored are the helium resonance emissions that are assumed to be radiation trapped and therefore not pertinent to photoionization. Here, experimental evidence for the presence of helium atomic emission in a pulsed discharge at ten’s of Torr is shown. Simulations of a discharge in similar conditions agree with the experimental measurements. In this context, the role of atomic and molecular helium light emission on photoionization of molecular nitrogen in an ionization wave is studied using a kinetic modeling approach that accounts for radiation dynamics in a developing low-temperature plasma. Three different mixtures of helium at a total pressure of 250 Torr are studied in simulation. Photoionization of the nitrogen molecule by vacuum ultraviolet helium emission is used as the only seed source ahead of the ionization front. It is found that even though radiation trapped, the atomic helium emission lines are the significant source of photoionization of nitrogen. The significant effect of radiation trapped photon emission on ionization wave dynamics demonstrates the need to consider these radiation dynamics in plasma reactors where self-absorbed radiation is ignored.

42 ENGINEERING↗
DOE OSTI2025

Spatial profile of argon (1s 5 ) metastables in an electron beam generated plasma

Electron beams with an applied magnetic field generate a secondary cold plasma with a selective chemical composition, featuring low-energy ions and metastable species in the discharge periphery, ideal for low-damage plasma treatment of material substrates. In this work, we studied the plasma generated by an e-beam using a 4 kV voltage in a pure argon gas environment under a magnetic field of 150 G and in the pressure range of 25–90 mTorr. We measured the absolute spatial density profile of argon (1 s 5 ) metastables in an electron beam generated plasma by laser-induced fluorescence and found it to be of the order of 10 16 m −3 . The electron temperature and the electron density measured by a Langmuir probe were of the order of 10 16 m −3 and less than an eV respectively. Electron-impact quenching was identified as a significant loss mechanism for the Ar(1s 5 ) state, leading to the saturation of the metastable density at higher pressures. Outside the primary ionization region, the spatial distribution of argon metastables followed a linear diffusion profile, indicating negligible additional production in those regions.

EEDF↗
DOE OSTI2020

Benchmark for Fuel Shuffling and Depletion for Pebble-Bed Reactors

Pebble bed reactors have specific operational characteristics when their fuel-cycle and fueling operations are considered. They are specifically distinguished by other type of nuclear reactor designs by their online fuel recycling scheme, where the fuel elements that have not yet reached discharge burnup can be reloaded and recycled continuously during normal operation. The fuel in a pebble bed reactor is not stationary and stochastically moves through the core once or several times during its lifetime, which allows them to operate without requiring a large excess reactivity hold for the burnup. However, this characteristic of pebble bed reactors introduces challenges in simulation, as each pebble can take many different trajectories through the core, its composition depends on the details of the irradiation history that is unique to its aggregated path through the core. For predicting the safety performance characteristics, such as source term, maximum fuel temperatures and fuel failure rates, etc., it is important to accurately incorporate the movement of pebbles through the core during their lifetime in a multi-physics simulation together with other phenomena. The equilibrium core analysis for pebble bed reactors are performed with multi-physics tools including fuel depletion in a multi pass reload coupled to the fuel movement. Currently, there are only a few legacy multi-physics simulation tools that can implement the pebble flow characteristics and perform equilibrium core analysis for pebble bed reactors. However, there are development efforts on-going under Department of Energy's Nuclear Energy Advanced Modelling and Simulation program and also in private industry for including these capabilities into their modelling and simulation tools. Any new development in the modelling and simulation tools needs to be validated by using tools such as experiments, analytical solutions or code-to-code benchmarks. In this work, a code-to-code benchmark for the equilibrium core analysis capability of pebble bed reactors was developed. Multiple cases were identified to capture different fuel cycle strategies that can be used in PBRs. The results of each case are presented in terms of overall equilibrium core characteristics: the discharge burnup; spatial burnup distribution; spatial isotopic distributions; axial and radial neutron flux distributions and power history of fuel elements per pass through the core for both a prototypical pebble bed High Temperature Gas-cooled Reactor and a prototypical pebble bed Fluoride-salt cooled High temperature Reactor.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Pumped Storage Hydropower Augmented with Pressurized Air: The Ground-Level Integrated Diverse Energy Storage (GLIDES) System — GLIDES System Configurations and Use Cases

Energy storage is essential for cost-effective integration of variable renewable energy sources to support a low-carbon grid. It is also a key enabler of a modern grid infrastructure for demand management. However, several main challenges remain for different kind of energy storage technologies in grid scale deployment. Currently, the largest source of utility-scale storage and long-duration storage in the US is pumped storage hydropower (PSH). Prospect of growth in conventional PSH faces challenges that have limited its deployment over the last three decades, including high capital costs and long deployment timelines. Batteries have high energy densities and are the primary technology of choice for small-scale energy storage. Compressed air energy storage (CAES) is another large-scale energy storage technology, but there are few plants deployed worldwide. They suffer from their low round trip efficiency (RTE) due to the use of high-pressure air compressors. To address some of the challenges associated with these various storage technologies, the Ground-Level Integrated Diverse Energy Storage (GLIDES) is a modular PSH technology that was invented in 2015 at Oak Ridge National Laboratory. It utilizes gas compression to store electric energy. GLIDES stores energy by compressing gas using a liquid piston in high-pressure vessels. In doing so the vessels act as the upper reservoir in conventional PSH. Initially, the vessels are filled with gas to a prescribed pressure. To store energy, GLIDES uses a hydraulic piston pump to pump water into the pressurized vessels. As the water volume increases inside the vessels, water acts as a hydraulic piston compressing the gas on top of it. This process can be thought of as pumping water from the lower reservoir to the higher reservoir in PSH, increasing the water head. To dispatch the stored energy, the high-head water in the vessel is discharge through a high head Pelton hydraulic turbine that is connected to an electric generator. Employing high-pressure vessels enables GLIDES to reach water heads ~10-80 times higher than conventional PSH, achieving ~40 times higher energy densities, and overcomes the geographic limitation of conventional PSH. Although its energy density is much lower than that of batteries, GLIDES holds the potential advantages of having long service life, ease of system integration and being less hazardous over batteries. GLIDES prospective scalability could make it suitable for wide range of applications from behind the meter storage in buildings to grid-scale storage. It also makes it suitable for installations in densely populated urban areas where energy storage is most needed and real estate is limited. Over the last 5 years, work has focused on increasing GLIDES’ energy density, decreasing its initial capital cost of the system, and increasing its revenue potential. Several designs were developed and prototyped to verify and demonstrate the improvement in energy density. The latest prototype achieved energy density of 1.21 kWh/m 3 . Our analysis showed that it could achieve up to 1.7 kWh/m 3 with a mixture of air and carbon dioxide as the gas being compressed.

13 HYDRO ENERGY↗
DOE OSTI2023

Coupled primary production and respiration in a large river contrasts with smaller rivers and streams

Abstract Although time series in ecosystem metabolism are well characterized in small and medium rivers, patterns in the world's largest rivers are almost unknown. Large rivers present technical difficulties, including depth measurements, gas exchange (, ) estimates, and the presence of large dams, which can supersaturate gases. We estimated reach‐scale metabolism for the Hanford Reach of the Columbia River (Washington state, USA), a free‐flowing stretch with an average discharge of 3173 . We calculated from semi‐empirical models and directly estimated it from tracer measurements. We fixed at the median value from these calculations (0.5 ), and used maximum likelihood to estimate reach‐scale, open‐channel metabolism. Both gross primary production (GPP) and ecosystem respiration (ER) were high (GPP range: 0.3–30.8 g , ER range: 0.8–30.6 g ), with peak GPP and ER occurring in the late summer or early fall. GPP increased exponentially with temperature, consistent with metabolic theory, while light was seasonally saturating. Annual average GPP, estimated at 1500 g carbon , was in the top 2% of estimates for other rivers. GPP and ER were tightly coupled and 90% of GPP was immediately respired, resulting in net ecosystem production near 0. Patterns in the Hanford Reach contrast with those in small‐medium rivers, suggesting that metabolism magnitudes and patterns in large rivers may not be simply scaled from knowledge of smaller rivers.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2022

2D imaging of absolute methyl concentrations in nanosecond pulsed plasma by photo-fragmentation laser-induced fluorescence

The methyl radical plays a central role in plasma-assisted hydrocarbon chemistry but is challenging to detect due to its high reactivity and strongly pre-dissociative electronically excited states. In this work, we report the development of a photo-fragmentation laser-induced fluorescence (PF-LIF) diagnostic for quantitative 2D imaging of methyl profiles in a plasma. This technique provides temporally and spatially resolved measurements of local methyl distributions, including in near-surface regions that are important for plasma-surface interactions such as plasma-assisted catalysis. The technique relies on photo-dissociation of methyl by the fifth harmonic of a Nd:YAG laser at 212.8 nm to produce CH fragments. These photofragments are then detected with LIF imaging by exciting a transition in the B-X(0, 0) band of CH with a second laser at 390 nm. Fluorescence from the overlapping A-X(0, 0), A-X(1, 1), and B-X(0, 1) bands of CH is detected near 430 nm with the A-state populated by collisional B-A electronic energy transfer. This non-resonant detection scheme enables interrogation close to a surface. The PF-LIF diagnostic is calibrated by producing a known amount of methyl through photo-dissociation of acetone vapor in a calibration gas mixture. We demonstrate PF-LIF imaging of methyl production in methane-containing nanosecond pulsed plasmas impinging on dielectric surfaces. Absolute calibration of the diagnostic is demonstrated in a diffuse, plane-to-plane discharge. Measured profiles show a relatively uniform distribution of up to 30 ppm of methyl. Relative methyl measurements in a filamentary plane-to-plane discharge and a plasma jet reveal highly localized intense production of methyl. The utility of the PF-LIF technique is further demonstrated by combining methyl measurements with formaldehyde LIF imaging to capture spatiotemporal correlations between methyl and formaldehyde, which is an important intermediate species in plasma-assisted oxidative coupling of methane.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Flexible Fully-Decoupled Nuclear Plants with Thermal Energy Storage - Technoeconomic Optimization

New nuclear power plants may be one of the technologies for future zero carbon electricity production. These future systems will however also need significant flexibility to cope with fluctuating demand and large share of intermittent renewable supply, rather than running in conventional baseload generation. The present work explores the use of thermal energy storage (TES) as a buffer between the reactor heat and its conversion to electricity, enabling flexible operation of nuclear plants. The focus is on maximizing flexibility, ideally as full decoupling of the nuclear and power cycle islands, as well as on system efficiency in various modes. A system design presented for a high temperature gas cooled reactor (HTGR) presents a slightly complex solution, as separate high- and low-temperature TES systems are required in order to cover the extended temperature range. Although this configuration imposes certain limitations on the discharge system configuration, it also presents the opportunity to design a more efficient system. For this case in particular, a steam reheat cycle is advantageous. Dynamic models were developed for the decoupled system in order to generate insights into aspects of off design operation and system control. A technoeconomic analysis, furthermore, provides sizing and costing of the component, followed by size and dispatch economic optimization considering energy arbitrage. This optimization shows that in all explored markets, the addition of TES system with the proposed configuration results in positive impact on project net present value. Further sensitivity analyses show impact of multiple inputs and possible technical limitations.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Investigation of Reaction Pathways and Temperature Inhibition in Methane DBD Plasmas at the Princeton Collaborative Research Facility (PCRF)

The overarching goal of this research is to advance the fundamental understanding of plasma-driven chemical conversion of light hydrocarbons using dielectric barrier discharges (DBDs). Using methane (CH 4 ) as a model system, the primary focus is to elucidate the influence of DBD plasma properties and environmental temperature on CH 4 plasma chemistry by studying decomposition products of the gas effluent across a broad range of conditions using experimental instrumentation at the Princeton Collaborative Research Facility (PCRF) located at the Princeton Plasma Physics Laboratory (PPPL). The insights obtained from this study are expected to form the mechanistic foundation for the design and optimization of plasma-catalytic reactions of light hydrocarbons for practical applications such as the recycling of production flare gas by transforming the uncaptured waste into value-added resources at the source of extraction, presenting a sustainable solution to a longstanding environmental challenge.

03 NATURAL GAS↗
DOE OSTI2022

Improvements to the High-Field-Side Transient CHI System on QUEST

Transient coaxial helicity injection (CHI) is a promising candidate for solenoid-free plasma current start-up in a low-aspect-ratio tokamak in support of developing fully non-inductive scenarios. The aim of the transient CHI research on QUEST is to develop a reactor-relevant CHI design. On QUEST, a CHI discharge is initiated by driving current along magnetic field lines that connect an electrically insulated electrode plate (which is referred to as a bias electrode) to a vessel component at the bottom region of the spherical tokamak. In the first application of CHI on QUEST, the electrically insulated electrode plate was biased with respect to the outer vessel in a configuration referred to as low-field-side (LFS) injection. To maintain a narrow injector flux footprint width throughout the discharge, QUEST is now developing a high-field-side (HFS) injection configuration, in which the electrically insulated electrode plate is biased with respect to the inner vessel components. Through the implementation of a CHI-dedicated gas injection system, studies in the HFS injection configuration have now demonstrated good magnetic flux evolution into the vacuum vessel. Toroidal currents up to 43 kA have been achieved, and the generated current has increased in proportion to the magnetic flux connecting the electrodes. Finally, these results which show agreement with the CHI-scaling suggest that much higher levels of toroidal current can be generated on QUEST in an optimized CHI system in which the magnetic flux connecting the CHI electrodes is further increased.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Molecular theory capability: LANL-PEM-Atomic implements universal descriptions of molecular photoionization

Photoionization of atomic ions, the process through which atoms in bound states absorb radiation by losing electrons, is a vital part of describing radiative transfer in mission-relevant dynamics. The photoionization of molecules dominates radiative transfer of ultraviolet (UV) and extreme UV (EUV) radiation in colder atmospheres (temperature < 30,000 degrees Kelvin). Consequently, air, which is quite transparent to our eyes (i.e., in the visible frequency regime) is remarkably opaque to radiation in much of the UV and EUV frequency regimes. This opacity makes air and other gas systems quite efficient at absorbing UV and EUV radiation, which heats the gas until ionization makes it transparent. This effect is important in describing a host of relevant phenomena, ranging from charge separation in high-altitude nuclear events and the dynamics of a nuclear fireball to the electrostatic discharges (sparks) that complicate weapons disassembly at Pantex.

74 ATOMIC AND MOLECULAR PHYSICS↗
DOE OSTI2021

Underwater plasma breakdown characteristics with respect to highly pressurized drilling applications

Deep earth drilling is a key technique to extract oil, gas, and geothermal heat from the earth. Many complex energy focusing methods have been explored as an alternative approach to reach these resources but most of them require high energy. However, by utilizing short time span liquid plasma discharges, energy focusing can be achieved within traditional drilling systems. These discharges induce a rapid expansion process and a resulting shockwave. It is believed that this focused energy will lower the required cutting force to progress through the rock. Lowering the required cutting force will allow for lower drill bit wear, quicker rate of penetration, and an overall cost savings of the project. Plasma breakdown characteristics at drilling relevant pressures, ranging from 1 to 350 atm, were studied. A resistance–capacitance circuit with an air gapped spark switch was utilized to generate pulsed plasma between the pressurized electrodes. It was found that the required breakdown voltage increases as the pressure increases. It was also found that a plasma channel formation and an associated breakdown may or may not occur between the electrodes at different pressures due to variation in required breakdown voltages. Breakdown time-lag in the dielectric medium (tap water, 780 μS cm –1 ) increased as the pressure was increased, which indicated a higher voltage drop at higher pressures (>100 atm). The plasma generated cavitation bubble with an associated shockwave occurred as pressures were increased. However, the bubble radius and the bubble duration decreased as the pressure was increased. The plasma generated shockwave speeds fall within the expected speed of sound in water. Lastly, preliminary rock cracking tests were performed on granite at high pressures (340 and 272 atm) and it was found that plasma is able to create cracks in the rock.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Extending the low-recycling, flat temperature profile regime in the lithium tokamak experiment-β (LTX-β) with ohmic and neutral beam heating

Abstract Recent experiments in the lithium tokamak experiment- β (LTX- β ) have extended the duration, performance, operating conditions, and diagnosis of the flat-temperature profile, low-recycling regime first observed in LTX. As expected, Li retains hydrogen and suppresses edge neutral cooling, allowing increased edge electron temperature, roughly equal to the core T e . Flat temperature profiles had been obtained transiently in LTX, as the plasma density decayed following the cessation of edge gas puffing. Careful control over the fueling in LTX- β has now been shown to sustain the flat T e profile and hot edge unique to the low-recycling regime for multiple confinement times in high performance discharges with decaying or steady density. With low density, the flat T e profile is also seen to extend into the scrape-off layer. Neutral beam heating is observed in target discharges with relatively flat electron temperature profiles ( T edge ∼ T core /2), though beam heating is stronger in discharges with higher fueling, higher density, and depressed edge T e . Beam heating produces additional peaking of the T e profile, without degradation of the energy confinement time. Neutral beam heating of target discharges with relatively flat electron temperature profiles similarly results in broad beam heated temperature profiles. Energy confinement in LTX- β generally compares favorably to ohmic and H-mode scalings, frequently exceeding them by factors of 2–4. New and improved diagnostics in LTX- β enable better characterization of this unique regime, including measurements of ion temperature and high field side Thomson scattering profiles. As an initial step toward characterizing turbulence with no T e gradient and roughly equal density and pressure gradient, core fluctuation spectra have been measured in peaked T e discharges using far-forward scattering and fluctuation reflectometry.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Evaluating the carbon footprint of the integrated DBD‐plasma bi‐reforming unit via laboratory scale experiments and scaled‐up process modeling

Catalytic dielectric barrier discharge (DBD) plasma reactor experiments were performed in a tubular glass reactor with a 2 mm gap at 550°C to facilitate the reaction kinetics of steam added dry reforming or bireforming. The best specific energy input obtained was 11.2 eV/molecule feed at CO 2 :CH 4 :H 2 O of 4.5:1:4.5 ratio and gas hour space velocity (GHSV) = 432 h −1 . This value was used to design a conceptual process and assess the environmental impact of methane steam reforming-based H 2 production 18.4 kmol/h CO 2 emission processing into H 2 :CO = 2 syngas, with an emphasis on the carbon footprint.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Repurposing Inactive Oil and Gas Wells for Energy Storage: Maximizing the Potential Via Optimal Drivetrain Control: Preprint

In recent years, there has been a growing emphasis on utilizing energy storage to enhance grid resilience against disruptive events. While renewable energy supply continues to expand, gravity-based solutions like pumped hydro remain dominant in the commercial space. However, their geographical limitations constrain availability, scalability, and increase costs for co-locating solar and wind energy. An alternative approach proposes repurposing idle oil and gas wells located closer to existing grid infrastructure, offering a promising and cost-effective solution. This paper addresses the optimization and control of a regenerative drive system coupled to an interior permanent magnet synchronous machine in a 300-meter well with a 100-Newton weight. The study employs a dynamic MATLAB/Simulink model to simulate the operation of the electric drivetrain system during storage and discharge operations. The results demonstrate an initial round-trip efficiency of 85.9% for the electrical system alone and identify crucial factors for maximizing efficiency. The optimized operation and control of the electromechanical drivetrain system hold great potential for minimizing the levelized cost of storage while maximizing efficiency and revenue generation.

ENERGY STORAGE,ENGINEERING↗