Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FIBER STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Mechanisms of boron fiber strengthening by thermal treatment

The fracture strain for boron on tungsten fibers can be improved by heat treatment under vacuum or argon environments. The mechanical basis for this improvement is thermally-induced axial contraction of the entire fiber, whereby strength-controlling core flaws are compressed and fiber fracture strain increased by the value of the contraction strain. By highly sensitive measurements of fiber density and volume, the physical mechanisms responsible for contraction under both environments was identified as boron atom diffusion out of the fiber sheath. The fiber contracts because the average volume of the resulting microvoid was determined to be only 0.26 + or - 0.09 the average atomic volume of the removed atom. The basic and practical implications of these results are discussed with particular emphasis on the theory, use, and limitations of heat-induced contraction as a simple cost-effective secondary processing method.

Dicarlo, J. A.↗

Composites That Exceed Superalloys In Rupture Strength

Ceramic-fiber-reinforced iron alloys show promise as turbine parts for intermediate-temperature service. Intermediate-temperature composites reduce weights of turbine blades by 40 percent and increase life expectancies of blades. In study, relatively-low-temperature fabrication process, hollow-cathode sputtering developed.

Petrasek, Donald W.↗

High-tip-speed fiber composite compressor blades: Vibration and strength analysis

An analytical procedure is described which couples composite mechanics computer codes with NASTRAN. This procedure was used to perform a detailed analysis of a high-tip-speed fiber composite compressor fan blade. The results indicate that the various vibration modes of this blade are highly coupled. Mechanical load ply stresses are well below the corresponding room temperature strengths. Lamination residual stresses are likely to cause transply cracks and interply delamination. Transply cracks and relaxation of root fixity decrease the vibrational frequencies whereas centrifugal stiffening increases them. Comparisons of results for various parameters are presented in tabular and graphical form.

Chamis, C. C.↗

High-tip-speed fiber composite compressor blades - Vibration and strength analyses

An analytical procedure is described which couples composite mechanics computer codes with NASTRAN. This procedure was used to perform a detailed analysis of a high-tip-speed fiber composite compressor fan blade. The results indicate that the various vibration modes of this blade are highly coupled. Mechanical load ply stresses are well below the corresponding room temperature strengths. Lamination residual stresses are likely to cause transply cracks and interply delamination. Transply cracks and relaxation of root fixity decrease the vibrational frequencies whereas centrifugal stiffening increases them. Comparisons of results for various parameters are presented in tabular and graphical form.

Chamis, C. C.↗

Fiber orientation and porosity in large-format extrusion process: The role of processing parameters

Controlling fiber orientation and porosity in short-fiber thermoplastic composites is important for enhancing mechanical, electrical and thermal properties in large-format additive manufacturing. This study employs a factorial design of experiments (DoE) to assess the effects of nozzle diameter (5.08 mm–10.16 mm), temperature (230–250 °C), and extruder screw speed (150–280 rpm) on flow rate, shear rate, porosity, fiber orientation, fiber length and tensile strength in 20 % carbon fiber-filled acrylonitrile butadiene styrene. ANOVA results show that screw speed significantly impacts flow rate, while nozzle diameter and temperature have lesser effects. Shear rate increases with smaller nozzles and higher speeds. Porosity decreases from 5.58 % with a 10.16 mm nozzle to 3.11 % with a 5.08 mm nozzle at 150 rpm due to increased shear rates, which induce shear thinning, reducing viscosity and facilitating gas escape. Larger nozzles (10.16 mm) produce larger, more heterogeneous pores, while smaller nozzles (5.08 mm) yield smaller, uniform pores. Beads produced with the 5.08 mm nozzle exhibit longer fiber lengths due to reduced residence time, lower shear stress, and better alignment. Fiber orientation improves with smaller nozzles due to higher shear rates but decreases with higher screw speeds (280 rpm) due to shorter residence times. The highest fiber alignment (A xx ∼ 0.65) and low porosity (∼3%) were achieved with a 5.08 mm nozzle at 150 rpm, while equivalent additive manufacturing-compression molding samples exhibited better tensile strength (∼93 MPa) under these conditions. In conclusion, these findings emphasize the importance of optimizing processing parameters to enhance fiber alignment and reduce porosity for improved mechanical performance.

Design of experiments↗

Halogenation Enhances Carbon-Fiber/Epoxy Composites

Interlaminar shear strength increased by inexpensive treatment. New surface treatment for carbon fibers enhances interlaminar shear strength, ILSS, without altering tensile strength significantly. Exposure of polyacrylonitrile-based T-300, or equivalent, fibers to bromine vapor at room temperature improves ILSS of epoxy composites made from these fibers by 30 percent. Enhanced ILSS obtained from halogenation of carbon fibers beneficial in many aerospace and terrestrial applications.

Jaworske, Donald A.↗

Production of fibers by a floating zone fiber drawing technique

A CO2 laser heated, floating zone fiber growth process was developed. The resulting Al2O3 fibers exhibited the high room temperature strengths for large diameter fibers as well as high specific creep rupture strengths observed at 1093 C and 1316 C (2000 F and 2400 F). Single crystal fibers of TiC and Y2O3 were also grown. An optical system was developed to focus four CO2 laser beams onto the surface of a feed rod permitting the formation of highly controllable molten zones. The optical system permitted energy densities and angle of incidence of the beams to be adjusted over wide ranges. This optical system was incorporated into a controlled atmosphere, fiber growth furnace. The two principal advantages of a CO2 laser heat source are that ambient atmospheres may be freely selected to optimize fiber properties and the laser has no inherent temperature limit, so extremely high melting point materials can be melted. Both advantages were demonstrated.

Haggerty, J. S.↗

Effects of Fiber/Matrix Interface and its Composition on Mechanical Properties of Hi-Nicalon/Celsian Composites

To evaluate the effects of fiber coatings on composite mechanical properties. unidirectional celsian matrix composites reinforced with uncoated Hi-Nicalon fibers and those precoated with a dual BN/SiC layer in two separate batches (batch 1 and batch 2) were tested in three-point flexure. The uncoated-fiber reinforced composites showed catastrophic failure with strength of 210+/-35 MPa and a flat fracture surface. In contrast, composites reinforced with coated fibers exhibited graceful failure with extensive fiber pullout and showed significantly higher ultimate strengths, 904 and 759 MPa for the batch 1 and 2 coatings. respectively. Fiber push-in tests and microscopic examination indicated no chemical reaction at the uncoated or coated fiber-matrix interfaces that might be responsible for fiber strength degradation. Instead, the low strength of composite with uncoated fibers was due to degradation of the fiber strength from mechanical damage during composite processing. Despite identical processing, the first matrix cracking stresses (Sigma(sub mc)) of the composites reinforced with fibers coated in batch 1 and batch 2 were quite different, 436 and 122 MPa, respectively. The large difference in Sigma(sub mc) of the coated-fiber composites was attributed to differences in fiber sliding stresses (Tau(sub friction)), 121.2+/-48.7 and 10.4+/-3.1 MPa, respectively. for the two composites as determined by the fiber push-in method. Such a large difference in Tau(sub friction). for the two composites was found to be due to the difference in the compositions of the interface coatings. Scanning Auger microprobe analysis revealed the presence of carbon layers between the fiber and BN. and also between the BN and SiC coatings in the composite showing lower Tau(sub friction). This resulted in lower Sigma(sub mc) in agreement with the ACK theory. The ultimate strengths of the two composites depended mainly on the fiber volume fraction and were not significantly effected by Tau(sub friction) values, as expected. The poor reproducibility of the fiber coating composition between the two batches was judged to be the primary source of the large differences in performance of the two composites.

Bansal, Narottam P.↗

Modeling of Time-Dependent Strength Degradation of SiC/SiC Ceramic Matrix Composites via MAC/GMC Computer Code

Silicon carbide fiber reinforced silicon carbide (SiC/SiC) ceramic matrix composites (CMCs) display time-dependent strength degradation at intermediate temperatures (600 to 900 degrees Centigrade). This is generally believed to be an oxidation induced phenomenon. The understanding of the effect of temperature with environment (oxidation) is key towards development of SiC/SiC CMCs with a reliable load carrying capacity. Various theories have been proposed to explain the strength degradation. One suggests that the boron nitride (BN) coating deposited on the fibers oxidizes causing fusion of fibers. Another theory proposes that the SiC fibers are oxidized forming a silica scale leading to premature fiber failure. A more recent theory suggests that SiC fiber strength is intrinsically time-dependent due to slow crack growth of flaws in the fibers. An empirical model, termed as a "fiber classic model," which is based on a standard slow crack growth type power-law, has been implemented within NASA's micromechanics-based MAC/GMC computer code as a user routine. Model parameters for this "classic model" were calibrated from stress-rupture data of Hi-Nicalon (TM) monofilaments using the maximum likelihood estimation (MLE) technique. This new capability in the MAC/GMC computer code was then used to predict the stress-rupture behavior of Hi-Nicalon (TM) tows as well as 2-D SiC/SiC composites reinforced with Hi-Nicalon (TM) fibers. Results demonstrate that the MAC/GMC with this new capability successfully predicts the time-to-failure vs. applied stress within the intermediate temperature range at various scales as well as laminated composites in an oxidizing environment.

Environmental degradation↗

Investigation of the reaction kinetics between SiC fibers and selectively alloyed titanium matrix composites and determination of their mechanical properties

During high temperature exposure, an interfacial reaction occurs between SiC fiber reinforcement and titanium matrices which can be detrimental to the mechanical properties of the composite. The reaction kinetics between SCS-6 fibers and Ti-1100 were determined at 800 to 1000 C and found to be slower than those of other currently used titanium alloys (Ti-15-3, Ti-6-4). The experimentally determined reaction kinetics for Ti-1100 were extrapolated to 700 C and found to accurately predict reaction zone size after 1000 hours of exposure. Predictions of the time to consume the surface layer on the SCS-6 and SCS-9 fibers were made in an effort to estimate the time that the fiber will retain its strength in Ti-1100 during isothermal exposure at high temperatures. Using this approach, the strength of an SCS-6 fiber in Ti-1100 should be retained for over 20,000 hours at isothermal exposures less than 800 C. Strength predictions using the rule of mixtures for a unidirectional Ti-1100/SCS-6 composite are presented for short term exposures up to 700 C. Room temperature tests of an as-fabricated 20 volume percent fiber/Ti-1100 composite yielded a UTS of 226 ksi (1490 MPa) which is close to that predicted by the ROM.

Gundel, Douglas B.↗

Compressive Failure of Fiber Composites under Multi-Axial Loading

This paper examines the compressive strength of a fiber reinforced lamina under multi-axial stress states. An equilibrium analysis is carried out in which a kinked band of rotated fibers, described by two angles, is sandwiched between two regions in which the fibers are nominally straight. Proportional multi-axial stress states are examined. The analysis includes the possibility of bifurcation from the current equilibrium state. The compressive strength of the lamina is contingent upon either attaining a load maximum in the equilibrium response or satisfaction of a bifurcation condition, whichever occurs first. The results show that for uniaxial loading a non-zero kink band angle beta produces the minimum limit load. For multi-axial loading, different proportional loading paths show regimes of bifurcation dominated and limit load dominated behavior. The present results are able to capture the beneficial effect of transverse compression in raising the composite compressive strength as observed in experiments.

Basu, Shiladitya↗

The interface in tungsten fiber reinforced niobium metal-matrix composites

The creep resistance of tungsten fiber reinforced niobium metal-matrix composites was evaluated. The interface region between the fiber and matrix was characterized by microhardness and electron probe microanalysis measurements which indicated that its properties were between those of fiber and matrix. However, the measured properties of the composite exceeded those calculated by the rule of mixtures even when the interface zone was assumed to retain all the strength of the fiber. The composite structure appeared to enhance the strengths of both the fibers and the matrix above what they exhibited in stand-alone tests. The effect of fiber orientation and matrix alloy composition on the fiber/matrix interface were also evaluated. Small alloying additions of zirconium and tungsten to the niobium matrix affected the creep resistance of the composites only slightly. A decrease in the creep resistance of the composite with increasing zirconium content in the matrix was ascribed to an increase in the diffusion rate of the fiber/matrix interdiffusion reaction, and a slight increase in the creep resistance of the composite was observed with an addition of 9 w percent tungsten to the matrix. In addition, Kirkendall void formation was observed at the fiber/matrix interface; the void distribution differed depending on the fiber orientation relative to the stress axis.

Grobstein, Toni L.↗

Fatigue Analysis of Notched Laminates: A Time-Efficient Macro-Mechanical Approach

A coupled transversely isotropic deformation and damage fatigue model is implemented within the finite element method and was utilized along with a static progressive damage model to predict the fatigue life, stiffness degradation as a function of number of cycles, and post-fatigue tension and compression response of notched, multidirectional laminates. Initially, the material parameters for the fatigue model were obtained utilizing micromechanics simulations and the provided [0], [90] and [plus or minus 45] experimental composite laminate S-N (stress-cycle) data. Within the fatigue damage model, the transverse and shear properties of the plies were degraded with an isotropic scalar damage variable. The damage in the longitudinal (fiber) ply direction was suppressed, and only the strength of the fiber was degraded as a function of fatigue cycles. A maximum strain criterion was used to capture the failure in each element, and once this criterion was satisfied, the longitudinal stiffness of the element was decreased by a factor of 10 (sup 4). The resulting, degraded properties were then used to calculate the new stress state. This procedure was repeated until final failure of the composite laminate was achieved or a specified number of cycles reached. For post-fatigue tension and compression behavior, four internal state variables were used to control the damage and failure. The predictive capability of the above-mentioned approach was assessed by performing blind predictions of the notched multidirectional IM7/977-3 composite laminates response under fatigue and post-fatigue tensile and compressive loading, followed by a recalibration phase. Although three different multidirectional laminates were analyzed in the course of this study, only detailed results (i.e., stiffness degradation and post-fatigue stress-train curves as well as damage evolution states for a single laminate ([30/60/90/minus 30/minus 60] (sub 2s)) are discussed in detail here.

Composite Fatigue analysis↗

Carbon fiber production at low temperatures from polyacrylonitrile

Recent safety considerations have sought to lower the electrical conductivity of carbon fibers. Carbon fibers produced from polyacrylonitrile at low carbonization temperatures (600-900 C) possess low electrical conductivity but do not possess adequate strength. Low-temperature processes are described which improve fiber strength but do not increase electrical conductivity substantially. The processes result in a carbon fiber with nearly twice the tensile strength compared to the old process. Process development and its effect on fiber properties are reported.

Cagliostro, D. E.↗

Feasibility and process scale-up low cost alumina fibers for advanced Re-usable Surface Insulation (RSI)

The objective of this program was to establish feasibility of a process to produce low cost aluminum oxide fibers having sufficient strength, flexibility, and thermal stability for multiple re-use at temperatures to 1480 C in advanced RSI type heat shields for reentry vehicles. Using bench-scale processing apparatus, the Alcoa 'Saphiber' process was successfully modified to produce nominally 8 microns diameter polycrystalline alpha-alumina fiber. Thermal stability was demonstrated in vacuum reheating tests to 1371 C and in atmospheric reheating to 1483 C. Individual fiber properties of strength, modulus, and flexibility were not determined because of friability and short length of the fiber. Rigidized tile produced from fiber of nominally 8, 20 and 40 micron diameter had thermal conductivities significantly higher than those of RSI SiO2 or mullite at relatively low temperature but became comparable above about 1000 C. Tile densities were high due to short fiber length, especially in the coarser diameter fiber. No significant effect of fiber diameter on thermal properties could be determined form the data. Mechanical properties of tiles deteriorated as fiber diameter increased.

Pearson, A.↗

Ply Strength Prediction of Unidirectional Continuous Carbon Fiber Composites

As inhomogeneous orthotropic materials, composite mechanical properties can be difficult to predict. Even with tight fabrication process controls, there is always some microstructural variation that will affect these properties. As a highly defect-dependent phenomena, mechanical strength is even more subject to variation, especially considering that composites exhibit multiple potential failure modes. The most direct way to determine composite material strength is via experimental testing, maintaining loading and specimen morphology as close as possible to the in situ states. When multiple materials and designs are being considered, this process is often prohibitively costly and slow. However, some approximations and rules of thumb can consistently guide the design process and consideration of alternatives.

36 MATERIALS SCIENCE↗