Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Engine emission”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Co-optimization of Heavy-Duty Fuels and Engines: Cost Benefit Analysis and Implications

Heavy-duty vehicles require expensive after treatment systems for control of emissions such as particulate matter (PM) and nitrogen oxides (NOx) to comply with stringent emission standards. Reduced engine-out emissions could potentially alleviate the emission control burden, and thus bring about reductions in the cost associated with after treatment systems, which translates into savings in vehicle ownership. This study evaluates potential reductions in manufacturing and operating costs of redesigned emission after treatment systems of line-haul heavy-duty diesel vehicles (HDDVs) with reduced engine-out emissions brought about by co-optimized fuel and engine technologies. Three emissions reduction cases representing conservative, medium, and optimistic engine-out emission reduction benefits are analyzed, compared to a reference case: the total costs of after treatment systems (TCA) of the three cases are reduced to 11,400(1.63 cents/km), 9,100 (1.30 cents/km), and 8,800 (1.26 cents/km), respectively, compared to 12,000 (1.71 cents/km) for the reference case. The largest potential reductions result from reduced diesel exhaust fluid (DEF) usage due to lower NOx emissions. Downsizing after treatment devices is not likely, because the sizes of devices are dependent on not only engine-out emissions, but also other factors such as engine displacement. As a result, sensitivity analysis indicates that the price and usage of DEF have the largest impacts on TCA reduction.

33 ADVANCED PROPULSION SYSTEMS↗

Design and evaluation of combustors for reducing aircraft engine pollution

Efforts in reducing exhaust emissions from turbine engines are reported. Various techniques employed and the results of testing are briefly described and referenced for detail. The experimental approaches taken to reduce oxides of nitrogen emissions include the use of: (1) multizone combustors incorporating reduced dwell times, (2) fuel-air premixing, (3) air atomization, (4) fuel prevaporization, and (5) gaseous fuel. Since emissions of unburned hydrocarbons and carbon monoxide are caused by poor combustion efficiency at engine idle, the studies of fuel staging in multizone combustors and air assist fuel nozzles have indicated that large reductions in these emissions can be achieved. Also, the effect of inlet-air humidity on oxides of nitrogen was studied as well as the very effective technique of direct water injection. The emission characteristics of natural gas and propane fuels were measured and compared with those of ASTM-Al kerosene fuel.

Jones, R. E.↗

Low pressure direct injection strategies effect on a small SI natural gas two-stroke engine’s energy distribution and emissions

This paper examines methods to simultaneously improve efficiency and reduce emissions from a 34 cc air-cooled two-stroke engine configured to operate on natural gas, using tuned intake plus exhaust resonators designed from Helmholtz resonance theory to promote effective scavenging. The engine was developed for novel application in a small, free piston engine for decentralized power generation. Operation occurred at wide-open-throttle at a speed of 5400 RPM for both port injection (PI) and low-pressure direct injection (LPDI). In both cases, the electronic ignition timing was adjusted for maximum brake torque, while the fuel was adjusted such that both rich and lean combustion were examined. The LPDI engine was then operated over a variety of engine speeds. An energy balance was completed for both PI and LPDI operation, which quantified all energy pathways, as engine operating regimes changed. Results showed that exhaust chemical energy (ECE) for LPDI was reduced significantly when compared to PI, mostly due to less fuel slip. The fuel slip rate ranged from 35 to 40% for PI operation while it was in the range of 6–20% for LPDI operation. However, mixture stratification with LPDI operation increased carbon monoxide emissions. The start-of-injection (SOI) was also examined, targeting a SOI to provide the highest trapping efficiency and most stable combustion. For LPDI operation, trapping efficiency, which is function of engine speed, showed significant effects on overall efficiency and fuel slip. Air volumetric efficiency increased due to the absence of gaseous fuel within the intake manifold. It was shown that, relative to PI, the overall engine indicated efficiency increased by 90% to a maximum indicated efficiency of 30% for LPDI operation with a SOI of 180 CAD BTDC.

42 ENGINEERING↗

Advanced Emission Control for High-Efficiency Engines

The CRADA between Cummins and Battelle will focus on: advanced emission control for high-efficiency engines. It will specifically focus on the following three areas: 1. Passive NOx absorbers - The purpose is to develop next generation materials that can be efficiently used to address the cold-operation, as driven by improved engine efficiency. 2. Oxidation of methane and short alkanes – The purpose is to address cold-operation emissions arising from CNG vehicles. 3. Improved understanding of particulates – The purpose is to understand how particulates are formed which will be used to develop strategies to address the tightening regulations and their enforcement for exhaust particulate matter. The first two areas will be based on PNNL’s technical leadership in the area of zeolite-based materials. The third area will have a shorter time scope to leverage the unique SPLAT capabilities at PNNL to help address Cummins’ needs in improving the understanding of particulates

02 PETROLEUM↗

Investigation of the Impact of Fuel Properties on Particulate Number Emission of a Modern Gasoline Direct Injection Engine

Gasoline Direct Injection (GDI) has become the preferred technology for spark-ignition engines resulting in greater specific power output and lower fuel consumption, and consequently reduction in CO2 emission. However, GDI engines face a substantial challenge in meeting new and future emission limits, especially the stringent particle number (PN) emissions recently introduced in Europe and China. Studies have shown that the fuel used by a vehicle has a significant impact on engine out emissions. In this study, nine fuels with varying chemical composition and physical properties were tested on a modern turbo-charged side-mounted GDI engine with design changes to reduce particulate emissions. The fuels tested included four fuels meeting US certification requirements; two fuels meeting European certification requirements; and one fuel meeting China 6 certification requirements being proposed at the time of this work. Two risk safeguard fuels (RSG), representing the properties of worst case market fuels in Europe and China, were also included. The particle number concentration of the solid particulates was measured in the engine-out exhaust flow at steady state engine operations with load and speed sweeps, and semi-transient load steps. The test results showed a factor of 6 PN emission difference among all certification fuels tested. Combined with detailed fuel analyses, this study evaluated important factors (such as oxygenates, carbon chain length and thermo-physical properties) that cause PN emissions which were not included in PMI index. A linear regression was performed to develop a PN predictive model which showed improved fitting quality than using PMI.

33 ADVANCED PROPULSION SYSTEMS↗

Performance Evaluation of Particle Sampling Probes for Emission Measurements of Aircraft Jet Engines

Considerable attention has been recently received on the impact of aircraft-produced aerosols upon the global climate. Sampling particles directly from jet engines has been performed by different research groups in the U.S. and Europe. However, a large variation has been observed among published data on the conversion efficiency and emission indexes of jet engines. The variation results surely from the differences in test engine types, engine operation conditions, and environmental conditions. The other factor that could result in the observed variation is the performance of sampling probes used. Unfortunately, it is often neglected in the jet engine community. Particle losses during the sampling, transport, and dilution processes are often not discussed/considered in literatures. To address this issue, we evaluated the performance of one sampling probe by challenging it with monodisperse particles. A significant performance difference was observed on the sampling probe evaluated under different temperature conditions. Thermophoretic effect, nonisokinetic sampling and turbulence loss contribute to the loss of particles in sampling probes. The results of this study show that particle loss can be dramatic if the sampling probe is not well designed. Further, the result allows ones to recover the actual size distributions emitted from jet engines.

Lee, Poshin↗

Comparison of steady-state and transient CVS cycle emission of an automotive Stirling engine

The Automotive Stirling Engine Development Program is to demonstrate a number of goals for a Stirling-powered vehicle. These goals are related to an achievement of specified maximum emission rates, a combined cycle fuel economy 30 percent better than a comparable internal-combustion engine-powered automobile, multifuel capability, competitive cost and reliability, and a meeting of Federal standards concerning noise and safety. The present investigation is concerned with efforts related to meeting the stringent emission goals. Attention is given to the initial development of a procedure for predicting transient CVS urban cycle gaseous emissions from steady-state engine data, taking into account the employment of the test data from the first-generation automotive Stirling engine. A large amount of steady-state data from three Mod I automotive Stirling engines were used to predict urban CVS cycle emissions for the Mod I Lerma vehicle.

Farrell, R. A.↗

Evaluation of an Aircraft Concept With Over-Wing, Hydrogen-Fueled Engines for Reduced Noise and Emissions

This report describes the analytical modeling and evaluation of an unconventional commercial transport aircraft concept designed to address aircraft noise and emission issues. A strut-braced wing configuration with overwing, ultra-high bypass ratio, hydrogen fueled turbofan engines is considered. Estimated noise and emission characteristics are compared to a conventional configuration designed for the same mission and significant benefits are identified. The design challenges and technology issues which would have to be addressed to make the concept a viable alternative to current aircraft designs are discussed. This concept is one of the "Quiet Green Transport" aircraft concepts studied as part of NASA's Revolutionary Aerospace Systems Concepts (RASC) Program. The RASC Program seeks to develop revolutionary concepts that address strategic objectives of the NASA Enterprises, such as reducing aircraft noise and emissions, and to identify enabling advanced technology requirements for the concepts.

Guynn, Mark D.↗

Correlation of nanoparticle size distribution features to spatiotemporal flame luminosity in gasoline direct injection engines

Particle size distribution measured by mobility instruments is a common diagnostic used to characterize ultrafine and nanoparticle emissions in engine exhaust; however, some features of particle size distribution data are poorly correlated to in-cylinder combustion phenomena. In this work, in-cylinder spatiotemporal flame luminosity is quantitatively correlated to features in the solid particle size distribution measured in the exhaust of a gasoline direct injection engine operating in lean and stoichiometric combustion modes. A multi-channel optical sensor was used to measure diffusion flame light intensity in different areas of the combustion chamber. Furthermore, total solid particle number and particle size distribution in the exhaust were measured using a scanning mobility particle sizer after a catalytic stripper that removed semi-volatile compounds. Results of the experiments showed that different flame phenomenon resulted in distinct particle size distribution characteristics. A large accumulation mode (particles with diameter of 50–100 nm) in the particle size distribution from stoichiometric engine operation with early injection resulted from anomalous diffusion flames like piston-top pool fires. In lean operation incorporating a secondary fuel injection, particle emissions were dominated by flame propagation through fuel-rich regions of the combustion chamber resulting in a comparatively broad particle size distribution. More generally, this work illustrates how particle size distribution data can be more accurately used to diagnose soot formation in gasoline direct injection engines.

33 ADVANCED PROPULSION SYSTEMS↗

Sensitivity of Emissions to Uncertainties in Residual Gas Fraction Measurements in Automotive Engines: A Numerical Study

Initial conditions of the working fluid (air-fuel mixture) within an engine cylinder, namely, mixture composition and temperature, greatly affect the combustion characteristics and emissions of an engine. In particular, the percentage of residual gas fraction (RGF) in the engine cylinder can significantly alter the temperature and composition of the working fluid as compared with the air-fuel mixture inducted into the engine, thus affecting engine-out emissions. Accurate measurement of the RGF is cumbersome and expensive, thus making it hard to accurately characterize the initial mixture composition and temperature in any given engine cycle. This uncertainty can lead to challenges in accurately interpreting experimental emissions data and in implementing real-time control strategies. Quantifying the effects of the RGF can have important implications for the diagnostics and control of internal combustion engines. This paper reports on the use of a well-validated, two-zone quasi-dimensional model to compute the engine-out NO and CO emission in a gasoline engine. The effect of varying the RGF on the emissions under lean, near-stoichiometric, and rich engine conditions was investigated. Numerical results show that small uncertainties (~2–4%) in the measured/computed values of the RGF can significantly affect the engine-out NO/CO emissions.

33 ADVANCED PROPULSION SYSTEMS↗

Engine Validation of Noise and Emission Reduction Technology Phase I

This final report has been prepared by Honeywell Aerospace, Phoenix, Arizona, a unit of Honeywell International, Inc., documenting work performed during the period December 2004 through August 2007 for the NASA Glenn Research Center, Cleveland, Ohio, under the Revolutionary Aero-Space Engine Research (RASER) Program, Contract No. NAS3-01136, Task Order 8, Engine Validation of Noise and Emission Reduction Technology Phase I. The NASA Task Manager was Dr. Joe Grady of the NASA Glenn Research Center. The NASA Contract Officer was Mr. Albert Spence of the NASA Glenn Research Center. This report is for a test program in which NASA funded engine validations of integrated technologies that reduce aircraft engine noise. These technologies address the reduction of engine fan and jet noise, and noise associated with propulsion/airframe integration. The results of these tests will be used by NASA to identify the engineering tradeoffs associated with the technologies that are needed to enable advanced engine systems to meet stringent goals for the reduction of noise. The objectives of this program are to (1) conduct system engineering and integration efforts to define the engine test-bed configuration; (2) develop selected noise reduction technologies to a technical maturity sufficient to enable engine testing and validation of those technologies in the FY06-07 time frame; (3) conduct engine tests designed to gain insight into the sources, mechanisms and characteristics of noise in the engines; and (4) establish baseline engine noise measurements for subsequent use in the evaluation of noise reduction.

Weir, Don↗

FY2017 Advanced Combustion Systems and Fuels Annual Progress Report

The Advanced Combustion Systems and Fuels Program supports VTO’s goal and focuses early-stage research and development (R&D) to improve understanding of the combustion processes, fuel properties, and emission control technologies while generating knowledge and insight necessary for industry to develop the next generation of engines.

33 ADVANCED PROPULSION SYSTEMS↗

Energy efficient engine component development and integration program

The development of the technology to improve energy efficiency of propulsion systems for subsonic commercial aircrafts was examined. Goals established include: (1) fuel consumption, reduction in flight propulsion system; (2) direct operation cost; (3) noise, with provision for engine growth corresponding to future engine application; and (4) emissions, EPA new engine standards.

Source record↗

Composition and Climate Impacts of Increasing Launches to Low Earth Orbit

We present simulations of an Earth system model in which launch vehicles inject gaseous and particulate combustion products into the stratosphere. We considered two plausible scenarios representative for the year 2050, one with 1000 launches per year and another with 10 times more, all of which assuming heavy lift (80 tons to low Earth orbit; LEO) launches using methane as a proxy for liquefied natural gas (LNG) fuel. An industry-standard plume flowfield model was used to predict emission of gaseous species including carbon monoxide, nitrogen oxides, and water vapor. Black carbon was introduced assuming vacuum emission equal 25% of equivalent kerosene engine. The gas emissions showed marginal or insignificant changes in atmospheric composition, while the black carbon emission was found to be the most influential component. Feedbacks involve tropopause and stratospheric warming, followed by a moistening of the stratosphere via tropospheric water vapor intrusions, together with a reduction in global albedo. The fact that LNG-fueled rockets could be a concern from aerosol emissions in our simulations, despite burning more efficiently than conventional fuels, underscores the need to better understand actual black carbon emissions from rocket engines in order to accurately predict the global impacts of launch vehicles on future climate.

Earth system model↗

Potential Adoption and Benefits of Co-Optimized Multimode Engines and Fuels for U.S. Light-Duty Vehicles

Exploring a diverse portfolio of technologies for decarbonization is crucial to understanding the potential impacts of different technological solutions and their associated environmental implications. Using high-octane, high-sensitivity biofuel blends in co-optimized multimode engines can increase engine efficiency and reduce vehicle emissions. Here, the multimode engine research focuses on the benefits of light-duty vehicle engines, which can operate in multiple modes depending on the vehicle's load. Low-temperature combustion can improve efficiency and reduce emissions (such as those from oxides of nitrogen and particulate matter) during low-load operation, while spark ignition performance is maintained in high-load operation. These advanced engines can be optimized to run on blends of biobased fuels. This analysis models scenarios for potential market adoption of co-optimized multimode vehicles fueled by three different bioblendstocks: ethanol, isopropanol, and isobutanol. An integrated modeling approach is used to forecast the energy and environmental impacts of the deployment of co-optimized multimode vehicles and fuels in the light-duty sector over the 2020-to-2050 time horizon. The multidisciplinary approach combines vehicle sales modeling, system dynamics modeling of the biorefining industry, and life cycle assessment to estimate the emissions and energy benefits. The models consider market forces such as consumer preferences for vehicle attributes, biofuel supply and demand dynamics subject to biorefinery capacity build-out and bioresource constraints, and forecasted changes to the U.S. bulk energy system over time. Market adoption of co-optimized vehicles is evaluated across a wide parameter space for incremental vehicle cost and engine efficiency improvement. This analysis reveals that the deployment of co-optimized multimode fuels and vehicles results in up to a 5% reduction in annual sector-wide life cycle greenhouse gas (GHG) emissions by 2050, relative to a business-as-usual scenario, but is also indicates environmental trade-offs, such as higher life cycle water-use. Emission benefits could potentially increase beyond 2050, as the new technologies penetrate the market and gain a foothold. Results also show that, under certain circumstances, vehicles with engines co-optimized for use with high-octane, high-sensitivity biofuel blends can be cost-competitive with conventional gasoline, while reducing GHG emissions. Our modeling results indicate that co-optimized multimode fuels and engines can be strategically leveraged in tandem with electrification to decarbonize the light-duty sector. Co-optimized vehicles could play a role in the early years of the time horizon, while electric vehicles (EVs) could become more competitive in the later years, highlighting the complementary benefits of these technologies for GHG reductions.

Oke, Doris↗

Mixed-Potential NO x and NH 3 Sensors Fabricated by Commercial Manufacturing Methods [Mixed-Potential Sensors NO x and NH 3 Fabricated by Commercial Manufacturing Methods]

Meeting EPA Tier 3 emissions reduction requirements while simultaneously increasing fuel economy to meet new CAFE standards will require optimization of advanced combustion strategies and emissions control technologies. There is an immediate need for suitable exhaust gas sensor technologies to monitor internal combustion engine tailpipe emissions and to control and maintain efficient operation of the engine and exhaust after treatment systems. NH 3 , NO x , and HC sensors could enable onboard diagnostics and combustion control in lean-burn engines, analogous to the role of O 2 sensors in stoichiometric burn engines. Commercial manufacturing methods have been used to fabricate self-heated mixed-potential sensors in a planar automotive configuration. By altering materials composition and operating conditions, we are able to obtain sensitivity/selectivity to each NH 3 , NO x and HCs. In addition, these devices exhibit stable performance over months of testing as a result of the stable morphology of the electrode/electrolyte/gas three-phase interface.

36 MATERIALS SCIENCE↗

Active Combustion Control for Aircraft Gas-Turbine Engines-Experimental Results for an Advanced, Low-Emissions Combustor Prototype

Lean combustion concepts for aircraft engine combustors are prone to combustion instabilities. Mitigation of instabilities is an enabling technology for these low-emissions combustors. NASA Glenn Research Center s prior activity has demonstrated active control to suppress a high-frequency combustion instability in a combustor rig designed to emulate an actual aircraft engine instability experience with a conventional, rich-front-end combustor. The current effort is developing further understanding of the problem specifically as applied to future lean-burning, very low-emissions combustors. A prototype advanced, low-emissions aircraft engine combustor with a combustion instability has been identified and previous work has characterized the dynamic behavior of that combustor prototype. The combustor exhibits thermoacoustic instabilities that are related to increasing fuel flow and that potentially prevent full-power operation. A simplified, non-linear oscillator model and a more physics-based sectored 1-D dynamic model have been developed to capture the combustor prototype s instability behavior. Utilizing these models, the NASA Adaptive Sliding Phasor Average Control (ASPAC) instability control method has been updated for the low-emissions combustor prototype. Active combustion instability suppression using the ASPAC control method has been demonstrated experimentally with this combustor prototype in a NASA combustion test cell operating at engine pressures, temperatures, and flows. A high-frequency fuel valve was utilized to perturb the combustor fuel flow. Successful instability suppression was shown using a dynamic pressure sensor in the combustor for controller feedback. Instability control was also shown with a pressure feedback sensor in the lower temperature region upstream of the combustor. It was also demonstrated that the controller can prevent the instability from occurring while combustor operation was transitioning from a stable, low-power condition to a normally unstable high-power condition, thus enabling the high-power condition.

DeLaat, John C.↗

Co-Optimization of Fuels and Engines

The Co-Optimization of Fuels and Engines (Co-Optima) initiative is a new DOE initiative focused on accelerating the introduction of affordable, scalable, and sustainable biofuels and high-efficiency, low-emission vehicle engines. The simultaneous fuels and vehicles research and development (R&D) are designed to deliver maximum energy savings, emissions reduction, and on-road vehicle performance. The initiative's integrated approach combines the previously independent areas of biofuels and combustion R&D, bringing together two DOE Office of Energy Efficiency & Renewable Energy research offices, ten national laboratories, and numerous industry and academic partners to simultaneously tackle fuel and engine research and development (R&D) to maximize energy savings and on-road vehicle performance while dramatically reducing transportation-related petroleum consumption and greenhouse gas (GHG) emissions. This multi-year project will provide industry with the scientific underpinnings required to move new biofuels and advanced engine systems to market faster while identifying and addressing barriers to their commercialization. This project's ambitious, first-of-its-kind approach simultaneously tackles fuel and engine innovation to co-optimize performance of both elements and provide dramatic and rapid cuts in fuel use and emissions. This presentation provides an overview of the project.

33 ADVANCED PROPULSION SYSTEMS↗