Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Elemental analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Finite Element Analysis of Poroelastic Composites Undergoing Thermal and Gas Diffusion

A theory for time-dependent thermal and gas diffusion in mechanically time-rate-independent anisotropic poroelastic composites has been developed. This theory advances previous work by the latter two authors by providing for critical transverse shear through a three-dimensional axisymmetric formulation and using it in a new hypothesis for determining the Biot fluid pressure-solid stress coupling factor. The derived governing equations couple material deformation with temperature and internal pore pressure and more strongly couple gas diffusion and heat transfer than the previous theory. Hence the theory accounts for the interactions between conductive heat transfer in the porous body and convective heat carried by the mass flux through the pores. The Bubnov Galerkin finite element method is applied to the governing equations to transform them into a semidiscrete finite element system. A numerical procedure is developed to solve the coupled equations in the space and time domains. The method is used to simulate two high temperature tests involving thermal-chemical decomposition of carbon-phenolic composites. In comparison with measured data, the results are accurate. Moreover unlike previous work, for a single set of poroelastic parameters, they are consistent with two measurements in a restrained thermal growth test.

Salamon, N. J.↗
NASA NTRS1995

Finite Element Analysis of an Energy Absorbing Sub-floor Structure

As part of the Advanced General Aviation Transportation Experiments program, the National Aeronautics and Space Administration's Langley Research Center is conducting tests to design energy absorbing structures to improve occupant survivability in aircraft crashes. An effort is currently underway to design an Energy Absorbing (EA) sub-floor structure which will reduce occupant loads in an aircraft crash. However, a recent drop test of a fuselage specimen with a proposed EA sub-floor structure demonstrated that the effects of sectioning the fuselage on both the fuselage section's stiffness and the performance of the EA structure were not fully understood. Therefore, attempts are underway to model the proposed sub-floor structure on computers using the DYCAST finite element code to provide a better understanding of the structure's behavior in testing, and in an actual crash.

Moore, Scott C.↗
NASA NTRS2001

Rapid Prototyping Integrated With Nondestructive Evaluation and Finite Element Analysis

Most reverse engineering approaches involve imaging or digitizing an object then creating a computerized reconstruction that can be integrated, in three dimensions, into a particular design environment. Rapid prototyping (RP) refers to the practical ability to build high-quality physical prototypes directly from computer aided design (CAD) files. Using rapid prototyping, full-scale models or patterns can be built using a variety of materials in a fraction of the time required by more traditional prototyping techniques (refs. 1 and 2). Many software packages have been developed and are being designed to tackle the reverse engineering and rapid prototyping issues just mentioned. For example, image processing and three-dimensional reconstruction visualization software such as Velocity2 (ref. 3) are being used to carry out the construction process of three-dimensional volume models and the subsequent generation of a stereolithography file that is suitable for CAD applications. Producing three-dimensional models of objects from computed tomography (CT) scans is becoming a valuable nondestructive evaluation methodology (ref. 4). Real components can be rendered and subjected to temperature and stress tests using structural engineering software codes. For this to be achieved, accurate high-resolution images have to be obtained via CT scans and then processed, converted into a traditional file format, and translated into finite element models. Prototyping a three-dimensional volume of a composite structure by reading in a series of two-dimensional images generated via CT and by using and integrating commercial software (e.g. Velocity2, MSC/PATRAN (ref. 5), and Hypermesh (ref. 6)) is being applied successfully at the NASA Glenn Research Center. The building process from structural modeling to the analysis level is outlined in reference 7. Subsequently, a stress analysis of a composite cooling panel under combined thermomechanical loading conditions was performed to validate this process.

Abdul-Aziz, Ali↗
NASA NTRS1977

Lunar elemental analysis obtained from the Apollo gamma-ray and X-ray remote sensing experiment

Gamma-ray and X-ray spectrometers carried in the service modules of the Apollo 15 and Apollo 16 spacecraft were employed for compositional mapping of the lunar surface. The measurements involved the observation of the intensity and characteristic energy distribution of gamma rays and X-rays emitted from the lunar surface. A large-scale compositional map of over 10 percent of the lunar surface was obtained from an analysis of the observed spectra. The objective of the X-ray experiment was to measure the K spectral lines from Mg, Al, and Si. Spectra were obtained and the data were reduced to Al/Si and Mg/Si intensity ratios and ultimately to chemical ratios. Analyses of the results have indicated (1) that the Al/Si ratios are highest in the lunar highlands and considerably lower in the maria, and (2) that the Mg/Si concentrations generally show the opposite relationship. The objective of the gamma-ray experiment was to measure the natural and cosmic-ray-induced activity emission spectrum. At this time, the elemental abundances for Th, U, K, Fe, Ti, Si, and O have been determined over a number of major lunar regions. Regions of relatively high natural radioactivity were found in the Mare Imbrium and Oceanus Procellarum regions.

Trombka, J. I.↗
NASA NTRS1996

Kinetics of Cyclic Oxidation and Cracking and Finite Element Analysis of MA956 and Sapphire/MA956 Composite System

Sapphire fiber-reinforced MA956 composites hold promise for significant weight savings and increased high-temperature structural capability, as compared to unreinforced MA956. As part of an overall assessment of the high-temperature characteristics of this material system, cyclic oxidation behavior was studied at 1093 C and 1204 C. Initially, both sets of coupons exhibited parabolic oxidation kinetics. Later, monolithic MA956 exhibited spallation and a linear weight loss, whereas the composite showed a linear weight gain without spallation. Weight loss of the monolithic MA956 resulted from the linking of a multiplicity of randomly oriented and closely spaced surface cracks that facilitated ready spallation. By contrast, cracking of the composite's oxide layer was nonintersecting and aligned nominally parallel with the orientation of the subsurface reinforcing fibers. Oxidative lifetime of monolithic MA956 was projected from the observed oxidation kinetics. Linear elastic, finite element continuum, and micromechanics analyses were performed on coupons of the monolithic and composite materials. Results of the analyses qualitatively agreed well with the observed oxide cracking and spallation behavior of both the MA956 and the Sapphire/MA956 composite coupons.

Lee, Kang N.↗
NASA NTRSDate not supplied

Finite Element Analysis Validation for Stitched, Blade-Stiffened Aerospace Structures

Increased performance and manufacturing rates for aircraft or spacecraft structures may be achieved using stitched and resin infused composite structures. In order to carry out design and analysis of stitched composites, 2-dimensional (2-D) and 3-dimensional (3-D) modeling approaches for stitched and non-stitched carbon fiber vacuum-infused parts were developed. These analysis approaches will be compared with data from previous test specimens tested at the NASA Langley Research Center (LaRC) under tension and bending load conditions. The preliminary results presented herein for the 2-D and 3-D models capture the strain patterns observed in digital image correlation (DIC) data for stitched, blade-stiffened specimens tested in either tension or bending. The analysis method study presented for these specimens is part of a larger analysis development effort planned for stitched composites, with the modeling practices developed here contributing to those that may be applied to a new set of blade- stiffened test specimens that are currently being manufactured for testing as well as the design of a blade stringer pull-off test. These future tests are expected to provide opportunities to validate the developed modeling approaches for predictive purposes, and to provide opportunities for further refinement of the modeling approaches.

HiCAM↗
NASA NTRS1999

Nondestructive Evaluation Correlated with Finite Element Analysis

Advanced materials are being developed for use in high-temperature gas turbine applications. For these new materials to be fully utilized, their deformation properties, their nondestructive evaluation (NDE) quality and material durability, and their creep and fatigue fracture characteristics need to be determined by suitable experiments. The experimental findings must be analyzed, characterized, modeled and translated into constitutive equations for stress analysis and life prediction. Only when these ingredients - together with the appropriate computational tools - are available, can durability analysis be performed in the design stage, long before the component is built. One of the many structural components being evaluated by the NDE group at the NASA Lewis Research Center is the flywheel system. It is being considered as an energy storage device for advanced space vehicles. Such devices offer advantages over electrochemical batteries in situations demanding high power delivery and high energy storage per unit weight. In addition, flywheels have potentially higher efficiency and longer lifetimes with proper motor-generator and rotor design. Flywheels made of fiber-reinforced polymer composite material show great promise for energy applications because of the high energy and power densities that they can achieve along with a burst failure mode that is relatively benign in comparison to those of flywheels made of metallic materials Therefore, to help improve durability and reduce structural uncertainties, we are developing a comprehensive analytical approach to predict the reliability and life of these components under these harsh loading conditions. The combination of NDE and two- and three-dimensional finite element analyses (e.g., stress analyses and fracture mechanics) is expected to set a standardized procedure to accurately assess the applicability of using various composite materials to design a suitable rotor/flywheel assembly.

Abdul-Azid, Ali↗
NASA NTRS1975

Correlation study of finite element analysis

A study was conducted to investigate and prove the correlation between the NASTRAN predicted stresses and those measured on an actual structure. NASTRAN is a general purpose digital computer program for the analysis of large complex structures. A real airframe, which had logged several thousand hours flying time, was obtained, instrumented, and loaded to obtain the measured strains.

Long, C. A.↗
NASA NTRS1977

Symbolic calculations in a finite dynamic element analysis

A second order problem is outlined for which MACSYMA was used only for checking purpose. A fourth order problem is briefly described for which a symbolic system is necessary. At the end, some sample output is displayed to indicate the complexity of the computational problem.

Gupta, K. K.↗
NASA NTRS1977

Finite element analysis of aeroacoustic jet-flap flows

A computational analysis was performed on the steady, turbulent aerodynamic flowfields associated with a jet-blown flap. For regions devoid of flow separation, a parabolic approximation to the governing time-averaged Navier-Stokes equations was applied. Numerical results are presented for the symmetry plane flow of a slot-nozzle planar jet flap geometry, including prediction of flowfield evolution within the secondary mixing region immediately downstream of the trailing edge. Using a two equation turbulence kinetic energy closure model, rapid generation and decay of large spatial gradients in mean and correlated fluctuating velocity components within the immediate wake region were predicted. Modifications to the turbulent flow structure, as induced by porous surface treatment of the flap, were evaluated. The recirculating flow within a representative discrete slot in the surface was evaluated, using the two dimensional, time-averaged Navier-Stokes equations.

Baker, A. J.↗
NASA NTRS1978

NASTRAN finite element analysis activity at Northrop

In-house evaluation of the various analytical capabilities of the MSC version of NASTRAN, prior to production release, is a continuous effort. The NASTRAN superelement and subsonic aero features are presently being tested and brought on-line for production use. Two examples of recent NASTRAN structural solutions are also presented.

Thordarson, S.↗
NASA NTRS1980

Finite element analysis of hyperelastic structures

The use of the penalty function, to account for near incompressibility is discussed and compared to that of Lagrange multiplier. A scheme to use Lagrange multiplier, without having to treat it as unknown, is also presented.

Tabaddor, F.↗
NASA NTRS1984

System for Structural Synthesis Combines Finite-Element Analysis and Optimization Programs

Programming System for Structural Synthesis, EAL/PROSSS, provides structural-synthesis capability by combining EAL and CONMIN computer programs with set of interface procedures. EAL is general-purpose finiteelement structural-analysis program; CONMIN is general-purpose optimization program. User supplies two smaller problem-dependent programs to define design variables, constraints, and objective function.

Rogers, J. L., Jr.↗