Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EUTECTIC ALLOY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18

Significantly Promoting the Thermal Conductivity and Machinability of Negative Thermal Expansion Alloy via In Situ Precipitation of Copper Networks

Rapid advancements in electronic devices yield an urgent demand for high-performance electronic packaging materials with high thermal conductivity, low thermal expansion, and great mechanical properties. However, it is a great challenge for current design philosophies to fulfill all the requirements simultaneously. Here, an effective strategy is proposed for significantly promoting the thermal conductivity and machinability of negative thermal expansion alloy (Zr,Nb)Fe 2 through eutectic precipitation of copper networks. The eutectic dual-phase alloy exhibits an isotropic chips-matched thermal expansion coefficient and a thermal conductivity enhancement exceeding 200% compared with (Zr,Nb)Fe 2 , along with an ultimate compressive strength of 550 MPa. The addition of copper reorganizes the composition of (Zr,Nb)Fe 2 , which smooths the magnetic transition and shifts it toward higher temperature, resulting in linear low thermal expansion in a wide temperature range. The highly fine eutectic copper lamellae construct high thermal conductivity networks within (Zr,Nb)Fe 2 , serving as highways for heat transfer electrons and phonons. The in situ forming of eutectic copper lamellae also facilitates the mechanical properties by enhancing interfacial bonding and bearing additional stress after yielding of (Zr,Nb)Fe 2 . This work provides a novel strategy for promoting thermal conductivity and mechanical properties of negative thermal expansion alloys via eutectic precipitation of copper networks.

36 MATERIALS SCIENCE↗

Elevated temperature properties of aligned ferrous eutectics

Iron base alloys containing aluminum and chromium together with smaller amounts of yttrium and silicon are of interest for high temperature applications. Strengthening an inherently weak but oxidation resistant solid solution matrix with aligned in situ chromium carbides represents an attractive approach to achieving both surface stability and creep resistance at elevated temperatures. Aligned microstructures were produced in alloys of approximately 30 wt % (Cr + Mn), about 3 wt % C and the balance Fe consisting of a gamma matrix and the hexagonal carbide (Cr, Mn, Fe)7C3. The tensile and stress rupture strength to 2000 F of aligned Fe-20 w/t % Cr-10 wt % Mn-3.2 wt % C measured parallel to the carbide reinforcement exceeded those of the strongest iron-nickel superalloys, e.g., CRM-6D developed by Chrysler for automotive turbine application. The cyclic oxidation and sulfidation response of these alloys at elevated temperatures can be markedly improved by aluminum additions.

Lemkey, F. D.↗

A study of deformation and strain induced in bulk by the oxide layers formation on a Fe-Cr-Al alloy in high-temperature liquid Pb-Bi eutectic

At elevated temperatures, heavy liquid metals and their alloys are known to create a highly corrosive environment that causes irreversible degradation of most iron-based materials. In this paper, it has been found that an appropriate concentration of oxygen in the liquid alloy can significantly reduce this issue by creating a passivating oxide scale that controls diffusion, especially if Al is present in Fe-based materials (by Al-oxide formation). However, the increase of the temperature and of oxygen content in liquid phase leads to the increase of oxygen diffusion into bulk, and to promotion of the internal Al oxidation. This can cause a strain in bulk near the oxide layer, due either to mismatch between the thermal expansion coefficients of the oxides and bulk material, or to misfit of the crystal lattices (bulk vs. oxides). This work investigates the strain induced into proximal bulk of a Fe-Cr-Al alloy by oxide layers formation in liquid lead-bismuth eutectic utilizing synchrotron X-ray Laue microdiffraction. Finally, it is found that internal oxidation is the most likely cause for the strain in the metal rather than thermal expansion mismatch as a two-layer problem.

36 MATERIALS SCIENCE↗

Influence of the Composition on the Solidification Path, Microstructure Evolution and Mechanical Properties of Al-Cu-Mg Alloys

The influence of the initial composition on the solidification path, microstructure evolution, thermophysical properties and mechanical properties of Al-Cu-Mg alloys was investigated. The solidification paths of the investigated alloys were determined by analyzing the solidification structure, and then the experimentally determined paths were compared with those from the calculated results. Three of the investigated alloys experienced typical ternary eutectic solidification, and the other four alloys experienced quasiperitectic reactions. Due to differences in the initial compositions, different eutectic morphologies were formed during the solidification process. The binary eutectic phases, (α-Al + Al{sub 2}Cu) and (α-Al + Al{sub 6}CuMg{sub 4}), and the (α-Al + Al{sub 6}CuMg{sub 4} + Al{sub 8}Mg{sub 5}) ternary eutectic phase tended to exhibit divorced growth, and the (α-Al + Al{sub 2}CuMg), (α-Al + Al{sub 6}CuMg{sub 4}) and (α-Al + Al{sub 2}Cu + Al{sub 2}CuMg) eutectic phases tended to exhibit coupled growth. The results indicated that the initial composition, solidification path, microstructure and morphology could greatly affect the melting enthalpy, microhardness and compressive strength of the investigated Al-Cu-Mg alloys.

36 MATERIALS SCIENCE↗

Intergranular precipitation-enhanced wetting and phase transformation in an Al0.4CoCrFeNi high-entropy alloy exposed to lead-bismuth eutectic

We report after exposure to oxygen-poor (10 -13 –10 -14 wt%) liquid lead-bismuth eutectic (LBE) at 500 °C for 500 h, LBE penetrates more than one order of magnitude deeper in an FCC Al 0.4 CoCrFeNi high-entropy alloy (HEA) decorated with a network of BCC (Ni, Al)-rich intergranular (IG) precipitates than in a single-phase, FCC Al 0.3 CoCrFeNi HEA without the IG precipitate network. This deterioration of corrosion resistance is attributed to the energetic nature of the BCC/FCC interphase boundaries (IBs) and resultant IB wetting. The LBE ingress film selectively leaches nickel located at those low-indexed crystalline planes, resulting in phase transformation from FCC to BCC structure.

36 MATERIALS SCIENCE↗

Microstructural development and mechanical properties of a near-eutectic directionally solidified Sn–Bi solder alloy

Sn–Bi solders may be applied for electronic applications where low-temperature soldering is required, i.e., sensitive components, step soldering and soldering LEDs. In spite of their potential to cover such applications, the mechanical response of soldered joints of Sn–Bi alloys in some cases does not meet the strength requirements due to inappropriate resulting microstructures. Hence, careful examination and control of as-soldered microstructures become necessary with a view to pre-programming reliable final properties. The present study aims to investigate the effects of solidification thermal parameters (growth rate — V{sub L} and cooling rate — T-dot{sub L}) on the microstructure of the Sn–52 wt.%Bi solder solidified under unsteady-state conditions. Samples were obtained by upward directional solidification (DS), followed by characterization through metallography and scanning electron microscopy (SEM). The microstructures are shown to be formed by Sn-rich dendrites decorated with Bi precipitates surrounded by a complex regular eutectic mixture, with alternated Bi-rich and Sn-rich phases. Experimental correlations of primary (λ{sub 1}), secondary (λ{sub 2}), tertiary (λ{sub 3}) dendritic and eutectic spacings (λ{sub coarse} and λ{sub fine}) with cooling rate and growth rate are established. Two ranges of lamellar eutectic sizes were determined, described by two experimental equations λ = 1.1 V{sub L}{sup −1/2} and λ = 0.67 V{sub L}{sup −1/2}. The onset of tertiary branches within the dendritic array along the Sn–52 wt.%Bi alloy DS casting is shown to occur for cooling rates lower than 1.5 °C/s. - Highlights: • The Sn–52 wt.%Bi solder was shown to have two eutectic sizes. • The fishbone eutectic is preferably located adjacent to the Bi-rich lamellar phases. • The onset of tertiary dendritic branches in Sn–Bi is associated with T-dot{sub L} < 1.5 °C/s. • Higher eutectic fraction and λ{sub 3} provoked a reverse increase in σ{sub u} and σ{sub y}.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Near-isothermal furnace for in situ and real time X-ray radiography solidification experiments

In this paper, we present a newly developed near-isothermal X-ray transparent furnace for in situ imaging of solidification processes in thin metallic samples. We show that the furnace is ideally suited to study equiaxed microstructure evolution and grain interaction. To observe the growth dynamics of equiaxed dendritic structures, a minimal temperature gradient across the sample is required. A uniform thermal profile inside a circular sample is achieved by positioning the sample in the center of a cylindrical furnace body surrounded by a circular heater arrangement. Performance tests with the hypo-eutectic Al-15wt.%Cu and the near-eutectic Al-33wt.%Cu alloys validate the near-isothermal character of the sample environment. Controlled cooling rates of less than 0.5 K min{sup −1} up to 10 K min{sup −1} can be achieved in a temperature range of 720 K–1220 K. Integrated in our rotatable laboratory X-ray facility, X-RISE, the furnace provides a large field of view of 10.5 mm in diameter and a high spatial resolution of ∼4 μm. With the here presented furnace, equiaxed dendrite growth models can be rigorously tested against experiments on metal alloys by, e.g., enabling dendrite growth velocities to be determined as a function of undercooling or solutal fields in front of the growing dendrite to be measured.

36 MATERIALS SCIENCE↗

Progress in advanced high temperature materials technology

Materials for intermediate temperature applications are considered, taking into account possibilities regarding the use of prealloyed powder processing to obtain superalloys with increased strength for turbine disk applications. Materials for high temperature application are also discussed. Attention is given to oxide dispersion strengthened alloys (ODS), ceramics, directionally solidified eutectics, ODS + gamma prime alloys, and composites. A description is presented of various approaches for providing environmental protection.

Freche, J. C.↗

Grain refinement of cast zinc through magnesium inoculation: Characterisation and mechanism

It was previously found that peritectic-forming solutes are more favourable for the grain refinement of cast Al alloys than eutectic-forming solutes. In this work, we report that the eutectic-forming solute, Mg, can also significantly grain refine cast Zn. Differential thermal analysis (DTA) of a Zn–Mg alloy, in which efficient grain refinement occurred, evidenced an unexpected peak that appeared before the nucleation of η-Zn grains on the DTA spectrum. Based on extensive examination using X-ray diffraction, high resolution SEM and EDS, it was found that: (a) some faceted Zn–Mg intermetallic particles were reproducibly observed; (b) the particles were located at or near grain centres; (c) the atomic ratio of Mg to Zn in the intermetallic compound was determined to be around 1/2. Using tilting selected area diffraction (SAD) and convergent beam Kikuchi line diffraction pattern (CBKLDP) techniques, these faceted particles were identified as MgZn{sub 2} and an orientation relationship between such grain-centred MgZn{sub 2} particles and the η-Zn matrix was determined. Hence, the unexpected peak on the DTA spectrum is believed to correspond to the formation of MgZn{sub 2} particles, which act as effective heterogeneous nucleation sites in the alloy. Together with the effect of Mg solute on restricting grain growth, such heterogeneous nucleation is cooperatively responsible for the grain size reduction in Zn–Mg alloys. - Highlights: • A new eutectic-based grain refiner for the cast Zn was found. • The formation process of an intermetallic compound (MgZn{sub 2}) was characterised. • MgZn{sub 2} can act as potent heterogeneous nucleation sites above the liquidus. • A new OR between MgZn{sub 2} and η-Zn was determined using the CBKLDP technique.

36 MATERIALS SCIENCE↗

Directionally solidified composite systems under evaluation

The directionally solidified eutectic in-situ composites being evaluated for use as turbine materials range from ductile-ductile systems, where both matrix and reinforcement are ductile, to brittle-brittle systems, where both phases are brittle. The alloys most likely to be used in gas turbine engines in the near term are the lamellar ductile-semi ductile alloys gamma prime-delta, Ni3Al-Ni3Nb and gamma/gamma prime-delta Ni,Cr,Cb,Al/Ni3Al-Ni3Nb and the fibrous ductile-brittle alloys M-MC CoTaC or NiTaC and M-M7C3(Co,Cr,Al)-(Cr,Co)7C3. The results of tests are given which indicate that gamma prime strengthened NiTaC alloys and a (Co,Cr,Al)7C3 have greater tensile strength than the strongest superalloys at temperatures up to about 600 C. The gamma prime-delta and gamma/gamma prime-delta alloys in the Ni,Al,Nb(Cr) systems have greater tensile strength than the superalloys at temperatures greater than 800 C. At low stresses fibrous carbide reinforced eutectic alloys have longer lives at high temperatures than the strongest superalloys. Lamellar delta, Ni3Nb reinforced eutectic alloys have longer lives at high temperatures than the strongest superalloys at all stresses. The experience currently being gained in designing with the brittle ceramics SiC and Si3N4 may eventually be applied to ceramic matrix eutectic in-situ composites. However, the refractory metal fiber reinforced brittle-ductile systems may find acceptance as turbine materials before the ceramic-ceramic brittle-brittle systems.

Ashbrook, R. L.↗

Directionally solidified composite systems under evaluation

The directionally solidified eutectic in-situ composites being evaluated for use as turbine materials range from ductile-ductile systems, where both matrix and reinforcement are ductile, to brittle-brittle systems, where both phases are brittle. The alloys most likely to be used in gas turbine engines in the near term are the lamellar ductile-semiductile alloys gamma prime-delta, Ni3Al-Ni3Nb and gamma/gamma prime-delta Ni,Cr,Cb,Al/Ni3Al-Ni3Nb and the fibrous ductile-brittle alloys M-MC CoTaC or NiTaC and M-M7C3(Co,Cr,Al)-(Cr,Co)7C3. Gamma-prime strengthened NiTaC alloys and a (Co,Cr,Al)-(Co,Cr)7C3 have greater tensile strength than the strongest superalloys at temperatures up to about 600 C. The gamma prime-delta and gamma/gamma prime-delta alloys in the Ni,Al,Nb(Cr) systems have greater tensile strength than the superalloys at temperatures greater than 800 C. At low stresses fibrous carbide reinforced eutectic alloys have longer lives at high temperatures than the strongest superalloys. Lamellar delta, Ni3Nb reinforced eutectic alloys have longer lives at high temperatures than the strongest superalloys at all stresses.

Ashbrook, R. L.↗

Effect of Eutectic Characteristics on Hot Tearing of Cast Superalloys

The occurrence of hot cracks in the blades of Ni-based superalloy turbocharger wheels is thought to be closely related to eutectic characteristics. Different alloys that are susceptible to hot tearing, namely K418, K419 and K424, were studied. SEM was used to obtain the microstructure of the alloys. DSC, isothermal solidification quenching process and EPMA were conducted to determine the relationship between the eutectic characteristics and solidification process, segregation behavior and dendrite coalescence. The results show that a large volume fraction of γ/γ′ eutectic indicates a wide-temperature solidification range and severe segregation. A large γ/γ′ eutectic size is a result of element segregation and poor dendrite coalescence. Ti is thought to promote the formation of a large isolated residual liquid pool and lead to a large eutectic size, leading to the poor coalescence behavior of the dendrites. The volume fraction and size of the γ/γ′ eutectic were considered, and a eutectic influence factor (E) was defined to evaluate the effect of eutectic characteristics on hot tearing in cast superalloys. It was found that a high E corresponds to high hot-tearing susceptibility.

36 MATERIALS SCIENCE↗

Dendritic growth of undercooled nickel-tin. III

The paper is concerned with structures and microsegregations in undercooled droplets of Ni-25 wt pct Sn and eutectic Ni-32.5 wt pct Sn alloys. An analysis of experimental results suggests that all samples solidify dendritically and that the final structures are largely the result of ripening. Experimental data on minimum solute composition in the samples produced are bounded by two curves both of which assume equilibrium at all liquid-solid interfaces during recalescence and subsequent cooling. The eutectic alloy samples often show a dendritic structure over the surface in areas where shrinkage is present. This structure appears to be the remnant of an original growth structure in which only limited ripening occurred, due to the rapid removal of interdendritic liquid by shrinkage.

Wu, Y.↗

The Effects of Grain Refinement and Rare Earth Intermetallics on Mechanical Properties of As-Cast and Wrought Magnesium Alloys

The effects of rare earth intermetallics and grain refinement by alloying and hot extrusion on the mechanical properties of Mg-Gd-Al-Zn alloys have been studied to elucidate some useful ways to enhance the mechanical properties of magnesium alloys. It was revealed that aluminum as an alloying element is a much better grain refining agent compared with gadolinium, but the simultaneous presence of Al and Gd can refine the as-cast grain size more efficiently. The presence of fine and widely dispersed rare earth intermetallics was found to be favorable to achieve finer recrystallized grains during hot deformation by extrusion. The presence of coarse dendritic structure in the GZ61 alloy, grain boundary eutectic containing Mg{sub 17}Al{sub 12} phase in the AZ61 alloy, and rare earth intermetallics with unfavorable morphology in the Mg-4Gd-2Al-1Zn alloy was found to be detrimental to mechanical properties of the alloy in the as-cast condition. As a result, the microstructural refinement induced by hot extrusion process resulted in a significant enhancement in strength and ductility of the alloys. The presence of intermetallic compounds in the extruded Mg-4Gd-2Al-1Zn and Mg-2Gd-4Al-1Zn alloys deteriorated tensile properties, which was related to the fact that such intermetallic compounds act as stress risers and microvoid initiation sites.

36 MATERIALS SCIENCE↗

Developing of nano sized fibrous eutectic silicon in hypereutectic Al–Si alloy by laser remelting

Laser surface melting followed by rapid solidification is an effective means to produce very fine microstructures with desirable surface properties because of the high rates of cooling associated with it. In the present study, the effect of rapid cooling on the silicon particle size, distribution, and morphology of hypereutectic Al–17wt.%Si and Al–20wt.%Si alloys have been investigated. A continuous-wave CO2 laser of wavelength 10.6 μm and a Trumpf Yb-YAG disk laser of wavelength 1.030 μm were used with a beam diameter of 1 mm and scanning speeds ranging from 5 to 100 mm/s. Rapid solidification increased the solubility of silicon in aluminum to approximately 5wt% and induced non-equilibrium hypoeutectic microstructures comprising large volume fractions of primary α-Al dendrites and ultrafine Al–Si eutectic of lamellar morphology. Both α-Al dendrites and the silicon particle sizes were significantly reduced from micron to nanoscale level. The morphology of silicon particles is modified from massive polygonal and plate-like to a mixture of fine fakes with round corners, feathery and fibrous, or a coral-like and thread-like structure. The eutectic silicon size and the interlamellar spacing were reduced to 30 and 10 nm, respectively. Furthermore, most of the silicon crystals in the eutectic region and the aluminum dendrites contained a significant number of twins which were considered as an essential contributor to the mechanism of growth and branching. Microhardness values increased two to threefold due to the refinement of the microstructural constituent.

42 ENGINEERING↗

Sn and Nb modified ultrafine Ti-based bulk alloys with high-strength and enhanced ductility

Sn and Nb modified ultrafine eutectic Ti-Fe alloys with high strength and plasticity prepared by cold crucible levitation melting were tested in compression at room temperature. (Ti{sub 70.5}Fe{sub 29.5}){sub 93.15}Sn{sub 3.85}Nb{sub 3} alloy exhibited an ultimate compressive strength of 2.36 GPa at 15% plastic strain. Electron microscopy revealed that lamellar structures in Ti{sub 70.5}Fe{sub 29.5} alloy could be tailored by the addition of Sn and Nb to obtain a globular structure. The microstructural refinement, morphology of phase constituents, and their relationships to the mechanical properties are discussed.

36 MATERIALS SCIENCE↗

Enhanced glass-forming ability of FeCoBSiNb bulk glassy alloys prepared using commercial raw materials through the optimization of Nb content

We optimized the alloy compositions by modifying the Nb content in [(Fe{sub 0.5}Co{sub 0.5}){sub 0.75}B{sub 0.20}Si{sub 0.05}]{sub 100-x}Nb{sub x}(x=3.6-4.4) alloy system. As a result, it was found that the Nb content of 4.3 at. % was effective for approaching alloy to a eutectic point. By copper mold casting, [(Fe{sub 0.5}Co{sub 0.5}){sub 0.75}B{sub 0.20}Si{sub 0.05}]{sub 95.7}Nb{sub 4.3} bulk glassy alloy rods with diameters up to 4 mm were successfully synthesized even using commercial raw materials. These glassy alloys exhibit a rather high saturation magnetization of 0.77 T and low coercive force of 2.5 A/m.

36 MATERIALS SCIENCE↗