Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Ductility”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Microstructure and strengthening of Al-6Ce-3Ni-0.7Fe (wt%) alloy manufactured by laser powder-bed fusion

In this study, an Al-6Ce-3Ni-0.7Fe (wt%) alloy was fabricated via laser powder-bed fusion and its microstructure, thermal stability, tensile properties, and creep properties are investigated for two rapid-solidification rates with different eutectic spacings. For both faster- and slower-cooled states, the as-fabricated alloy mostly shows elongated grains with very fine eutectic networks (~40 nm lamellar width) comprising a high-volume fraction (~18 %) of intermetallic phases. Faster-cooled samples, however, display a less continuous eutectic network with finer spacing (~100 nm), leading to higher Orowan strengthening and therefore superior microhardness and yield stress up to ~350 °C. Upon aging (300 - 450 °C), micron-size Al 9 (Ni,Fe) 2 needle-like precipitates form within grains, and the Al 11 Ce 3 eutectic network spheroidizes, while retaining a submicron width and spacing, resulting in 33–37 % drop in microhardness after 144 h aging at 400 °C. Limited tensile ductility (~6 %) and creep ductility (~1-2 %) are measured for both faster- and slower-cooled alloys due to an inhomogeneous microstructure, where cavitation preferentially initiates at melt-pool boundaries, precipitate-free zones, and/or denuded zones, eventually leading to local fracture. Denuded zones, induced by stress, form due to diffusional flow with stress-dependent orientations, and are identified as microstructurally weak regions leading to strain localization. The present alloy does not show a significant difference in 300 °C creep resistance between: (i) tensile and compressive loading, (ii) faster- and slower-cooled samples, and (iii) continuous and spheroidized eutectics. Creep resistance at 300 °C is comparable to that of a Ce-richer Al-10.5Ce-3.1Ni-1.2Mn (wt%) alloy, despite the formation of denuded zones and needle-like Al 9 (Ni,Fe) 2 precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Mechanical behavior of carbonated MgO-based Engineered Cementitious Composite (ECC) after high temperatures exposure

Carbonated MgO-based Engineered Cementitious Composite (ECC) has ultrahigh tensile ductility and tight crack width control behavior. However, the expectation of improved fire-resistant has not been confirmed. This study explored the alterations to mechanical and microstructure characteristics of this material after exposure to temperatures up to 500 °C. Material mass loss, compressive strength, tensile strength, strain capacity, and matrix fracture toughness were measured. Scanning electron microscopy, mercury intrusion porosimetry, thermogravimetric analysis, and X-ray diffraction were used to probe the degradation of the cement matrix and fibers. The effect of elevated temperature on carbonated MgO-based ECC was further assessed via examination of the micromechanical behavior of the fiber-matrix. The objective of this research was to assess the performance of carbonated MgO-based ECC exposed to fire hazards. The tensile ductility of carbonated MgO-based ECC was found to be enhanced when exposed to ~100 °C as compared with those at room temperature ~20 °C. Further increase in exposure temperature, however, posed a negative impact on the composite compressive strength, ultimate tensile strength, and ability to control crack width. Here the results provide a useful database for further investigations into carbonated MgO-based ECC for fire safety enhancement.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Material processing, microstructure, and composite properties of low carbon Engineered Cementitious Composites (ECC)

Traditional PVA fiber-reinforced Engineered Cementitious Composites (ECC) show high tensile ductility and superior durability with tight crack width, but the high cost and embodied carbon can hinder its wider application in infrastructures. The objective of this study is to develop a better understanding of the fresh and hardened properties of an ECC that employs a lower embodied-carbon binder, Limestone Calcined Clay Cement (LC3), and lower-cost PP fiber that is widely available. Specifically, the interrelations between material processing, microstructure, and composite properties were studied experimentally. The results showed that ECC with high tensile ductility up to 9% tensile strain and tight crack width with 50 μm at 2% tensile strain can be achieved. It was found that a matrix paste with higher viscosity generally enhanced fiber dispersion uniformity and robustness in tensile strain-hardening. The paste viscosity is increased when OPC is replaced by LC3 and can be tuned with superplasticizer content. Larger maximum flaw size leads to lower first crack strength, beneficial for microcrack initiation and multiple cracking. This study generates fundamental knowledge linking processing-microstructure-performance of PP-LC3-ECC. This class of low embodied carbon ECC with tight crack width is expected to contribute to reducing the carbon footprint of the built environment.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Microstructure and water absorption of ancient concrete from Pompeii: An integrated synchrotron microtomography and neutron radiography characterization

There is renewed interest in using advanced techniques to characterize ancient Roman concrete due to its exceptional durability and low-carbon footprint. In the present work, samples were drilled from the “Hospitium” in Pompeii and were analyzed by synchrotron microtomography (μCT) and neutron radiography to study how the microstructure, including the presence of induced cracks, affects their water adsorption. The water distribution and absorptivity were quantified by neutron radiography. The 3D crack propagation, pore size distribution and orientation, tortuosity, and connectivity were analyzed from μCT results using advanced imaging methods. Porosity was also measured by mercury intrusion porosimetry (MIP) as a reference. Ductile fracture patterns were observed once cracks were introduced. Compared to Portland cement mortar/concrete, the Pompeii samples had relatively high porosity, low connectivity, and a similar coefficient of capillary penetration. In addition, permeability was predicted from models based on percolation theory and pore structure data to evaluate the fluid transport properties. Understanding the microstructure of ancient Pompeii concrete is important because it could inspire the development of modern concrete with high durability.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Mechanical and self-healing behavior of low carbon engineered cementitious composites reinforced with PP-fibers

While the ultrahigh tensile ductility and superior durability of Engineered Cementitious Composites (ECC) have been demonstrated, the relatively high energy and carbon intensity, as well as high material cost present potential impediments to broader ECC applications. The objective of this research is to develop a more sustainable and cost-effective ECC. The ordinary Portland cement (OPC) and the commonly used PVA fiber in conventional ECC were replaced by limestone calcined clay cement (LC3) and polypropylene (PP) fiber, respectively. The ECC compressive strength, tensile stress-strain relationship, and microcrack self-healing behavior were studied at three water to binder ratios (0.3, 0.2, 0.16). The novel LC3-PP-ECC showed a tensile strain capacity of greater than 6% and an intrinsically tight crack width below 82 μm when loaded to 1% tensile strain. Further, the LC3-PP-ECC demonstrated efficient recovery of the composite tensile ductility and ultimate tensile strength through self-healing. Compared to typical ECC made with OPC and PVA fiber, the material cost, embodied energy and carbon footprint of LC3-PP-ECC are reduced by 61%, 45%, and 48%, respectively. Here, the superior mechanical properties and durability combined with the low environmental impact and cost for material production promote LC3-PP-ECC as a sustainable material for structural and non-structural applications.

42 ENGINEERING↗
DOE OSTI2024

Testing and modeling of CLT-to-CLT joints made using hardwood dowels and screws with varying spacing

With the increasing popularity of mass timber, utilizing large-diameter wood screws and hardwood dowels can offer an easy and cost-efficient way to join structural elements. However, the existing research on hardwood dowels is limited to single fastener joints under monotonic loading. No research is available on the group effects of joints with multiple hardwood dowels. Here, this paper presents the results of 96 monotonic and cyclic single-shear plane CLT-to-CLT joint tests with hardwood dowels (Red Oak and Yellow Birch, 25.4 mm diameter) and self-tapping wood screws (8 mm diameter) in Grand-Fir CLT, where screws were inserted both perpendicular and at a 45-degree angle to the grain for comparison to hardwood dowels. The study evaluated the mechanical properties of the joints by changing fastener spacing. Mechanical properties such as yielding and peak strength, displacement, elastic and yielding stiffness, and ductility were evaluated. The results showed equal strength and stiffness properties for hardwood dowels comparable with large-diameter screws. Additionally, the hardwood dowel joints demonstrated moderate ductility properties. The strength and stiffness of the tested joints were compared with analytical equations found in the literature by considering the group action factor of the fasteners. Lastly, a nonlinear force-displacement model was presented and compared to the experimental results and analytical calculations, which gives the possibility to predict and optimize the mechanical behavior of hardwood dowel and screw joints with varying numbers and spacing between fasteners.

36 MATERIALS SCIENCE↗
DOE OSTI2025

The Path towards Plasma Facing Components: A Review of State-of-the-art in W-Based Refractory High-Entropy Alloys

Developing advanced materials for plasma-facing components (PFCs) in fusion reactors is a crucial aspect for achieving sustained energy production. Tungsten (W) - based refractory high-entropy alloys (RHEAs) have emerged as promising candidates due to their superior radiation tolerance and high-temperature strength. This review paper will focus on recent advancements in W-based RHEA research, particularly emphasizing the key role of modelling using machine learning (ML) in the stage of discovery by predicting properties for each composition and expediting the identification of optimal RHEA compositions with desired properties. Additionally, the application of additive manufacturing (AM) techniques for fabricating W-based RHEAs is explored, highlighting their advantages for rapid prototyping and multi-compositional sample production in a high throughput manner. The review critically evaluates the current understanding of mechanical properties relevant to PFC applications, including high-temperature strength and ductility. Furthermore, the radiation tolerance of W-based RHEAs under irradiated conditions is discussed. Finally, the validity of current AM-manufactured W-based RHEAs as PFC materials is assessed, and key challenges and opportunities for future research are identified. This review aims to provide a comprehensive overview of W-based RHEAs for fusion applications and their potential to guide the development and validation of advanced refractory high entropy alloys.

Hatler, Caleb [University of Wisconsin-Madison]↗
DOE OSTI2024

The damage Mechanics challenge Results: Participant predictions compared with experiment

In this article, We present results from a recent exercise where participating organizations were asked to provide model-based blind predictions of damage evolution in 3D-printed geomaterial analogue test articles. Participants were provided with a range of data characterizing both the undamaged state (e.g., ultrasonic measurements) and damage evolution (e.g., 3-point bending, unconfined compression, and Brazilian testing) of the material. In this paper, we focus on comparisons between the participants’ predictions and the previously secret challenge problem experimental observations. We present valuable lessons learned for the application of numerical methods to deformation and failure in brittle-ductile materials. The exercise also enables us to identify which specific types of calibration data were of most utility to the participants in developing their predictions. Further, we identify additional data that would have been useful for participants to improve the confidence of their predictions. Consequently, this work improves our understanding of how to better characterize a material to enable more accurate prediction of damage and failure propagation in natural and engineered brittle-ductile materials.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Experimental data for damage mechanics simulation challenge

While there are many computational approaches for simulating damage in rock and other materials, few have been ground truth tested with either known experimental data or with blind data sets. Here, in this work, we present a bench-mark laboratory data set for a damage mechanics challenge to compare computational approaches on damage evolution in brittle-ductile materials. The samples were fabricated through additive manufacturing to produce repeatable specimens designed to fail in controlled ways. The failure was induced in the samples using a 3-point bending test to produce different Modes such as Mode I and mixed Modes including I-II, I-III and I-II-III Modes to generate a calibration data set and a blind challenge data set. Data collected included spatial and temporal measurements from traditional digital load–displacement sensors, 2D digital image correlation measurement to map surface deformations, 3D X-ray microscopy to ground-truth the crack-failure geometry, and laser profilometry to capture surface roughness. The data sets are available, on a data repository, to the community to advance computational models to improve our ability to predict damage in brittle-ductile materials.

3-point bending↗
DOE OSTI2026

Effect of Specimen Thickness on Fracture Toughness and Plane Stress to Plane Strain Transition in Medium-Density Polyethylene

This study investigates the effect of specimen thickness on fracture toughness and the transition from plane stress to plane strain conditions in Medium-Density Polyethylene (MDPE) using Single Edge Notched Bend (SENB) specimens. Three thickness groups (7.5 mm, 9.0 mm, and 12.1 mm) were tested following ASTM D5045 protocol. Conditional stress intensity factors (KQ) increased from 2.2 MPavm to 2.8 MPavm with increasing thickness, demonstrating significant size dependency. Confocal microscopy revealed a 34% reduction in maximum crack tip opening displacement (CTOD) from 0.478 mm to 0.314 mm as thickness increased, with plastic zone lateral extent decreasing by 32%. This quantitative evidence validates Irwin's theoretical prediction of plastic zone size transition from plane stress r_y˜ (1/2p) (K_I/s_y )^2 to plane strain conditions r_y˜ (1/6p) (K_I/s_y )^2.Scanning electron microscopy confirmed progressive suppression of shear lips and evolution from ductile tearing with extensive polymer chain drawing in thin specimens to localized crazing in thick specimens. Despite all specimens satisfying the ASTM D5045 criterion (B = 2.5(KQ/s_y )^2 ) ,residual shear lips persisted even in the thickest specimens, demonstrating that nominal size requirements alone are insufficient for achieving complete plane strain conditions in highly ductile polymers. The findings emphasize the necessity of integrated analytical and morphological assessment for valid fracture toughness characterization, with critical implications for life assessment and integrity prediction in thick-section polymer components such as natural gas distribution pipelines.

Medium-Density Polyethylene↗
DOE OSTI2020

Constitutive modeling of δ-phase zircaloy hydride based on strain rate dependent nanoindentation and nano-scale impact dataset

In this work, a constitutive model for zircaloy-4 embedded with δ-phase hydride rim/blister structures (δ-phase zircaloy hydride) is presented. Nanoindentation and nano-scale impact experiments were performed on the δ-hydride blisters as a function of temperature in order to obtain strain rate dependent location specific constitutive response. A power law viscoplastic constitutive model was chosen to represent the strain rate dependent behavior. The strength coefficient and the strain hardening exponent in the power law relation were found to decrease with increase in temperature indicating softening behavior at higher temperatures. The strain rate exponent remained constant with increase in temperature indicating that the rate dependent ductility does not change significantly at higher temperatures. A finite element method based model was created to analyze the failure behavior and the ductile to brittle transition in zircaloy hydride. The model predicted that fracture strength of δ-phase zircaloy hydride decreases linearly with increase in temperature.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Microstructure, compression properties, and oxidation behavior of Hf-25Ta-5Me alloys (Me is Mo, Nb, W, 0.5Mo + 0.5 W, Cr, or Zr)

Hf–Ta based alloys have recently been investigated as potential candidates for high-temperature structural applications. While most attentions have been given to the properties above ~1200 °C where the alloys are mainly single-phase BCC structures and have excellent oxidation performance due to formation of super-oxides, structural properties at lower temperatures are equally important for applications in which an alloy may experience a range of temperatures. In the present work, microstructure, phase composition, mechanical properties and oxidation behavior of six Hf-25Ta-5Me alloys (Me is Mo (HTM alloy), W (HTW), 0.5Mo + 0.5 W (HTMW), Cr (HTC) or Zr (HTZ), the compositions are in at.%) are reported at temperatures below the eutectoid transformation. The alloys were prepared by arc melting followed by hot isostatic pressing for 3 h at 1400 °C and 207 MPa. All the alloys display coarse grains of partially or fully transformed (by a eutectoid reaction) high-temperature BCC phase. The eutectoid regions consist of fine lamellae of Hf-rich HCP and Ta-rich BCC phases. The ternary alloys containing W or Cr also contained small amounts of a cubic Laves phase. At 25 °C, the HTW alloy was the strongest (yield stress σ y = 1966 MPa) but brittle and HTZ was the weakest (σ y = 1120 MPa) but ductile among the studied alloys. Other alloys showed intermediate behaviors. In general, the room temperature ductility of the alloys increased with decreasing σy. All alloys maintained high strength up to 800 °C, but displayed a noticeable strength decrease at 1000 °C. At 1000 °C, HTMW was the strongest alloy (σ y = 468 MPa) and HTC was the weakest alloy (σ y = 368 MPa). All alloys had excellent deformability at 1000 °C. Oxidation behavior of the alloys was studied at 800 °C and 1000 °C and compared with that of Hf–27Ta binary alloy. Although the ternary additions improved oxidation resistance, overall oxidation performance of the studied alloys at 800 °C and 1000 °C was poor.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Reformulating a Gurson-based dynamic damage model and demonstrating improved predictive power and numerical robustness

The original Tepla (TEnsile PLAsticity) ductile damage model, based on the Gurson yield surface, has long been used to model damage evolution and material failure under dynamic loading. Unfortunately, Tepla suffered from mesh sensitivity, numerical instability, and limited predictive capability. Here, we theoretically reformulate Tepla to address these issues. We especially focus on the prediction of porosity, which is the key state variable used for modeling ductile damage, as compared to more easily measured surface velocities, which are at best an indirect measure of damage. Key model changes include separating the viscosity during volumetric void growth from underlying shear strength behavior and switching to an iterative bisection solver. The new Tepla is then calibrated on incipient spall experiments on half-hard copper and tantalum, which demonstrate its ability to simultaneously fit the model to recovered porosity distributions and measured surface velocities, a stringent test. Improved numerical behavior, such as greatly reduced mesh sensitivity, is also shown in those simulations. Finally, the new Tepla model is applied to several high-explosive loaded, sweeping wave experiments, showing the ability of the model to predict behavior on tests with significantly different loading conditions and histories than the calibration data.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Investigation of crossed-twin structure formation in magnesium and magnesium alloys

In this work, the effect of alloying addition on the propensity for twin-twin interactions to transform into crossed-twin structures in magnesium alloys is investigated. A full-field elasto-viscoplastic fast Fourier transform (EVP-FFT) framework combined with a discrete twin model and dislocation density-based hardening law for slip strengths is used to calculate the micromechanical fields in the crystalline matrix around the interacting twins. AZ31 and MgLi alloys are selected along with pure Mg to study the influence of plastic anisotropy in connection with alloying elements. These alloys were selected since their plastic anisotropy measure, which is defined as the ratio between the critical resolved shear stress for pyramidal $\langle$c +a$\rangle$ and basal $\langle$a$\rangle$ slip modes, spanned a wide range. To quantify the role of twin thicknesses, we probe a range of impinging twin thicknesses while fixing the recipient twin thickness. The analysis reveals that: (i) the local driving stress for crossed twin structure formation generated from the interaction of the two twins is lower in a low plastically anisotropic material, like a MgLi alloy, than a high plastically anisotropic material like pure Mg and (ii) the critical impinging twin thickness needed to form the crossed twin structure in pure Mg, AZ31 and MgLi alloys is ~0.5, ~0.75 and ~1.5 times the recipient twin thickness. We propose a relationship between the tendency for crossed twin structure formation and the experimentally observed higher ductility in MgLi alloys compared to pure Mg. Finally, one key implication of the findings is that crossed- twin structure formation can be hindered and the ductility of magnesium alloy thereby improved by properly choosing alloying elements that lower the slip strength for pyramidal $\langle$c + a$\rangle$ slip.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Influence of oxygen on performance of multi-principal element alloy as braze filler for Ni-base alloys

In manufacturing of multi-principal element alloys (MPEAs), the casting process is often a primary point of oxygen introduction to the material system, which was demonstrated by the laboratory scale button arc-melting process. Oxygen introduction raises concerns for the mechanical performance of these alloys if employed as structural materials alone or in engineering applications, such as serving as filler materials to enable joining of similar or dissimilar alloy pairs that are conventionally considered difficult to join. In this work, oxide inclusions in an as-cast off-equiatomic MnFeCoNiCu MPEA and Ni-base alloy braze joints made with this MPEA were evaluated by synchrotron x-ray diffraction mapping and electron microscopy. MnO was found to be prevalent throughout the cast MPEA and was chemically reduced during brazing by trace Al from the base material, Ni-base Alloy 600. Incomplete reaction of the MnO with Al, and some alternative reaction with Cr, left a mixture of MnO, Al 2 O 3 , and Cr 2 O 3 in the as-brazed joint, with the oxides concentrated near the braze centerline due to directional solidification. Further, in the braze joints, the non-oxide constituent phases detected were an FCC matrix and particles of Cr 23 C 6 , Cr 7 C 3 , and TiN which are all native to Alloy 600. The evolution of oxides within the brazed joints at elevated service temperatures of 600-800°C was also evaluated. While MnO and Al 2 O 3 were stable during high-temperature service, Cr 2 O 3 particles grew to several hundred microns, with dissolved oxygen in the MPEA providing a significant source for oxide growth. Comparing tensile performance of the as-brazed condition with post-service conditions showed that the evolution of oxide particles contributed to an increase in strength and decrease in ductility of the brazed joints. Evaluating particle morphologies among fracture surfaces of individual specimens demonstrated that large Cr 2 O 3 particles and continuous cluster networks of Al 2 O 3 were the features most detrimental to total elongation. Hence, unmitigated evolution of oxygen-containing species during brazing and service conditions is detrimental to the ductility of the brazed joints, which highlights the importance of oxygen control in initial manufacturing of MPEAs for engineering applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Microstructure analysis and machinability of additively manufactured A205 aluminum with heat treatments

A205 aluminum is one of the few high-strength aluminum alloys discovered for additive manufacturing (AM). The microstructure and heat treatment effects of AM A205 vary from those of its cast form, indicating possible differences in machinability during post-processing. Here, the objective of this research is to determine these variations of AM A205 and their effects on machinability using the cast condition as the baseline. As built and two heat-treated conditions (solution treatment and age hardening) were applied and compared in terms of their microstructures, micro-hardness, and machinability including vibration, specific cutting energy, chip morphology, and surface finish. The effects of print orientations on machinability were tested as well and found to be insignificant. AM as built had a higher hardness and slightly better machinability than its cast as built cast counterpart due to a smaller grain size (1 µm vs. 15 µm), eutectic θ-Al 2 Cu lattice and a fine, homogeneous TiB 2 distribution. The solution treatment dissolved this θ-Al 2 Cu lattice and increased the grain size (3 µm) which decreased the hardness, increased the ductility seen in the chips, and reduced the overall machinability. The presence of θ’-Al 2 Cu precipitates improved the machinability of aged AM A205. In addition, it was found that A205 exhibited both ductile and brittle behavior depending on the cutting speed, thus producing different machinability. The speed dependency is related to the material condition and heat treatment.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Dislocation dynamics in heterogeneous nanostructured materials

Crystalline materials can be strengthened by introducing dissimilar phases that impede dislocation glide. At the same time, the changes in microstructure and chemistry usually make the materials less ductile. One way to circumvent the strength–ductility dilemma is to take advantage of heterogeneous nanophases which simultaneously serve as dislocation barriers and sources. Owing to their superior mechanical properties, heterogeneous nanostructured materials (HNMs) have attracted a lot of attention worldwide. Nevertheless, it has been difficult to characterize dislocation dynamics in HNMs using classical continuum models, mainly due to the challenges in describing the elastic and plastic heterogeneity among the phases. Here, in this work, we advance a phase-field dislocation dynamics (PFDD) model to treat multi-phase materials, consisting of phases differing in composition, structural order, and size in the same system. We then apply the advanced PFDD model to exploring two important but divergent materials design problems in HNMs: dislocation/obstacle interactions and dislocation/interface interactions. Results show that the interactions between a dislocation and distribution of obstacles varying in structure and composition cannot be understood by simply interpolating from their individual interactions with a dislocation. It is also found that materials containing interfaces with nanoscale thicknesses and compositional gradients have a much higher dislocation bypass stress than those with sharp interfaces, providing an explanation for the simultaneous high strength and toughness of thick interface-containing nanolaminates as observed in recent experiments.

36 MATERIALS SCIENCE↗