Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Drag coefficient”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 325 records · Page 18
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

A computer program for estimating the aerodynamic characteristics of NACA 16-series airfoils

A computer program written in a table ""look-up'' format, is presented which provides a comprehensive data base on NACA 16-series airfoils. The geometry covered is limited to cambers for a design-lift coefficient from 0.0 to 0.7 and thickness ratios from 4 to 21%. The data include Mach numbers from 0.3 to 1.6, angles of attack from -4 to 8 degrees, and lift coefficients from 0.0 to 0.8. Extrapolation is used to obtain data from Mach numbers, angles of attack, and lift coefficients beyond those for which data are available. A routine to adjust the lift and drag coefficients beyond stall is included. The uses and limitations of the program are also discussed.

Maksymiuk, C. M.↗
NASA NTRS1989

Computational design of low aspect ratio wing-winglet configurations for transonic wind-tunnel tests

Computational designs were performed for three different low aspect ratio wing planforms fitted with nonplanar winglets; one of the three configurations was selected to be constructed as a wind tunnel model for testing in the NASA LaRC 8-foot transonic pressure tunnel. A design point of M = 0.8, C(sub L) is approximate or = to 0.3 was selected, for wings of aspect ratio equal to 2.2, and leading edge sweep angles of 45 deg and 50 deg. Winglet length is 15 percent of the wing semispan, with a cant angle of 15 deg, and a leading edge sweep of 50 deg. Winglet total area equals 2.25 percent of the wing reference area. The design process and the predicted transonic performance are summarized for each configuration. In addition, a companion low-speed design study was conducted, using one of the transonic design wing-winglet planforms but with different camber and thickness distributions. A low-speed wind tunnel model was constructed to match this low-speed design geometry, and force coefficient data were obtained for the model at speeds of 100 to 150 ft/sec. Measured drag coefficient reductions were of the same order of magnitude as those predicted by numerical subsonic performance predictions.

Kuhlman, John M.↗
NASA NTRS1934

Tests of three tapered airfoils based on the N.A.C.A. 2200, the N.A.C.A.-M6, and the Clark Y sections

Three tapered airfoils based on the N.A.C.A. 2200, the N.A.C.A.-M6, and the Clark Y sections were tested in the variable-density wind tunnel at a Reynolds Number of approximately 3,100,000. The models, which were of aspect ratio 6, had constant core center sections and rounded tips, and tapered in thickness from 18 percent at the roots to 9 percent at the tips. The aerodynamic characteristics are given by the usual dimensionless coefficients plotted for both positive and negative angles of attack and by effective profile-drag coefficients plotted against lift coefficients.

Anderson, Raymond F↗
NASA NTRS1999

In-flight adaptive performance optimization (APO) control using redundant control effectors of an aircraft

Practical application of real-time (or near real-time) Adaptive Performance Optimization (APO) is provided for a transport aircraft in steady climb, cruise, turn descent or other flight conditions based on measurements and calculations of incremental drag from a forced response maneuver of one or more redundant control effectors defined as those in excess of the minimum set of control effectors required to maintain the steady flight condition in progress. The method comprises the steps of applying excitation in a raised-cosine form over an interval of from 100 to 500 sec. at the rate of 1 to 10 sets/sec of excitation, and data for analysis is gathered in sets of measurements made during the excitation to calculate lift and drag coefficients C.sub.L and C.sub.D from two equations, one for each coefficient. A third equation is an expansion of C.sub.D as a function of parasitic drag, induced drag, Mach and altitude drag effects, and control effector drag, and assumes a quadratic variation of drag with positions .delta..sub.i of redundant control effectors i=1 to n. The third equation is then solved for .delta..sub.iopt the optimal position of redundant control effector i, which is then used to set the control effector i for optimum performance during the remainder of said steady flight or until monitored flight conditions change by some predetermined amount as determined automatically or a predetermined minimum flight time has elapsed.

Gilyard, Glenn B.↗
NASA NTRS1952

Low-Speed Wind-Tunnel Investigation of the Drag of a Lockheed F-94C Airplane (A.F. No. 50-956)

The aerodynamic characteristics in pitch of an F-94C airplane, with the primary attention given to its drag characteristics, have been evaluated at low speed in the Ames 40- by 80-foot wind tunnel. The increments of drag due to various surface irregularities, ports, and component parts of the production airplane were determined. Wing-wake surveys were taken to determine the section drag coefficients at midsemispan for the smooth and the production wing. Base-pressure and internal drags of the air-induction system were measured at low inlet-velocity ratios. The characteristics of the airplane in the landing configuration are also included.

Maki, Ralph L.↗
NASA NTRS2015

Mach Stability Improvements Using an Existing Second Throat Capability at the National Transonic Facility

Recent data quality improvements at the National Transonic Facility have an intended goal of reducing the Mach number variation in a data point to within plus or minus 0.0005, with the ultimate goal of reducing the data repeatability of the drag coefficient for full-span subsonic transport models at transonic speeds to within half a drag count. This paper will discuss the Mach stability improvements achieved through the use of an existing second throat capability at the NTF to create a minimum area at the end of the test section. These improvements were demonstrated using both the NASA Common Research Model and the NTF Pathfinder-I model in recent experiments. Sonic conditions at the throat were verified using sidewall static pressure data. The Mach variation levels from both experiments in the baseline tunnel configuration and the choked tunnel configuration will be presented and the correlation between Mach number and drag will also be examined. Finally, a brief discussion is given on the consequences of using the second throat in its location at the end of the test section.

Chan, David T.↗
NASA NTRS1959

Transonic Aerodynamic Characteristics of a 45 deg Swept Wing Fuselage Model with a Finned and Unfinned Body Pylon Mounted Beneath the Fuselage or Wing, Including Measurements of Body Loads

An investigation of a model of a standard size body in combination with a representative 45 deg swept-wing-fuselage model has been conducted in the Langley 8-foot transonic pressure tunnel over a Mach number range from 0.80 to 1.43. The body, with a fineness ratio of 8.5, was tested with and without fins, and was pylon-mounted beneath the fuselage or wing. Force measurements were obtained on the wing-fuselage model with and without the body, for an angle-of-attack range from -2 deg to approximately 12 deg and an angle-of-sideslip range from -8 deg to 8 deg. In addition, body loads were measured over the same angle-of-attack and angle-of-sideslip range. The Reynolds number for the investigation, based on the wing mean aerodynamic chord, varied from 1.85 x 10(exp 6) to 2.85 x 10(exp 6). The addition of the body beneath the fuselage or the wing increased the drag coefficient of the complete model over the Mach number range tested. On the basis of the drag increase per body, the under-fuselage position was the more favorable. Furthermore, the bodies tended to increase the lateral stability of the complete model. The variation of body loads with angle of attack for the unfinned bodies was generally small and linear over the Mach number range tested with the addition of fins causing large increases in the rates of change of normal-force coefficient and nose-down pitching-moment coefficient. The variation of body side-force coefficient with sideslip for the unfinned body beneath the fuselage was at least twice as large as the variation of this load for the unfinned body beneath the wing. The addition of fins to the body beneath either the fuselage or the wing approximately doubled the rate of change of body side-force coefficient with sideslip. Furthermore, the variation of body side-force coefficient with sideslip for the body beneath the wing was at least twice as large as the variation of this load with angle of attack.

Wornom, Dewey E.↗
NASA NTRSDate not supplied

Validating Drag and Heating Coefficients for Hollow Reentry Objects in Continuum Flow Using a Mach 7 Ludwieg Tube

Drag and heating coefficient databases and models are crucial to destructive reentry simulation. The NASA Orbital Debris Program Office (ODPO) develops, maintains, and performs analysis with the Object Reentry Survival Analysis Tool (ORSAT), which comprises drag and heating models for free molecular, transitional, and continuum flow regimes. These models have, in the past, only included solid, convex, blunt shapes (such as boxes, spheres, and cylinders). Previous work led by ODPO includes the extension of these models to hollow cylinders and square boxes in free molecular and transitional flow using the Direct Simulation Monte Carlo (DSMC) method. Since 2019, the ODPO has continued its program of DSMC simulations and extended the project to include analyses with the NASA Data Parallel Line Relaxation (DPLR) program on hollow cylinders and boxes (with varying wall thickness-diameter ratio). In fall 2022, the ODPO began a collaboration with the University of Texas San Antonio (UTSA) to use the Mach 7 Ludwieg Tube facility to validate the model built using numerical simulations. This facility can replicate (at a scale of approximately 100:1) the conditions seen by reentering objects near typical demise altitudes. We present here the drag and heating coefficients derived from the continued DSMC simulations, the new DPLR simulations, and the 26-test series at UTSA.

Chris Ostrom↗
NASA NTRS2023

Validating Drag and Heating Coefficients for Hollow Reentry Objects in Continuum Flow Using a Mach 7 Ludwieg Tube

Drag and heating coefficient databases and models are crucial to destructive reentry simulation. The NASA Orbital Debris Program Office (ODPO) develops, maintains, and performs analysis with the Object Reentry Survival Analysis Tool (ORSAT), which comprises drag and heating models for free molecular, transitional, and continuum flow regimes. These models have, in the past, only included solid, convex, blunt shapes (such as boxes, spheres, and cylinders). Previous work led by ODPO includes the extension of these models to hollow cylinders and square boxes in free molecular and transitional flow using the Direct Simulation Monte Carlo (DSMC) method. Since 2019, the ODPO has continued its program of DSMC simulations and extended the project to include analyses with the NASA Data Parallel Line Relaxation (DPLR) program on hollow cylinders and boxes (with varying wall thickness-diameter ratio). In fall 2022, the ODPO began a collaboration with the University of Texas San Antonio (UTSA) to use the Mach 7 Ludwieg Tube facility to validate the model built using numerical simulations. This facility can replicate (at a scale of approximately 100:1) the conditions seen by reentering objects near typical demise altitudes. We present here the drag and heating coefficients derived from the continued DSMC simulations, the new DPLR simulations, and the 26-test series at UTSA.

Chris Ostrom↗
NASA NTRS1985

Supercritical airfoil drag reduction by passive shock wave/boundary layer control in the Mach number range .75 to .90

Airfoils operating in the transonic region are subject to large increases in drag due to shock wave/boundary layer interactions. The concept of passive shock wave/boundary layer control seeks drag reduction by placing a thin cavity with a porous top surface at the airfoil chordwise position where a shock wave would normally occur. The higher pressure behind the shock wave circulates flow through the cavity to the lower pressure ahead of the shock wave. The effects from this circulation prevent boundary layer separation and reduce entropy increases through the shock wave. In this investigation this concept is studied at a freestream Mach number range of .75 and .90. The Mach number distributions over the model, the wake impact pressure surveys used to determine profile drag and schlieren photographs for 2.8 percent porosity and solid airfoil cases are presented and compared. Results indicate that the profile drag coefficient can be reduced by as much as 40 percent through the use of this passive drag control system.

Nagamatsu, H. T.↗
NASA NTRS1988

A preliminary investigation of drag reduction and mechanism for a blunt body of revolution with slanted base

This is a preliminary study of the drag reduction effect and its mechanism of a blunt body of revolution with a 21-deg slant angle by using a series of base plates. Drag coefficients were measured to investigate the effect of base installation position and plate height. An effective drag reduction device was found. Through the measurement of base pressure and total pressure distribution and flow pattern display, flow characteristics and drag reduction mechanism in the vortex near the wake were investigated.

Xia, Xuejian↗
NASA NTRS1996

High Altitude Towed Glider

The concept of using an unmanned towed glider for high altitude scientific research had been previously proposed. This paper examines the feasibility of this concept by determining what impact the various characteristics of the tow line, glider and tow aircraft have on tow line drag. A description of the analysis and computer code used to generate the results is given. The parameters examined were glider altitude, tow aircraft glider separation distance, velocity, tow line drag coefficient and tow line material properties. The results from the analysis show that the tow line drag increases significantly with tow aircraft/glider separation. The drag increased from 940 N (211 lb) with a tow aircraft/glider separation of 3 km to 11,970 N (2691 lb) with a tow aircraft/glider separation of 10 km. The results also show that by varying some of the initial assumptions significant reductions in tow line drag and weight can be obtained. The variables which had the greatest effect on reducing the tow line drag were the decrease in tow aircraft/glider separation distance, the increase in tow line strength and the decrease in glider Mach number.

Colozza, Anthony J.↗
NASA NTRS1998

Design and Performance Calculations of a Propeller for Very High Altitude Flight

Reported here is a design study of a propeller for a vehicle capable of subsonic flight in Earth's stratosphere. All propellers presented were required to absorb 63.4 kW (85 hp) at 25.9 km (85,000 ft) while aircraft cruise velocity was maintained at Mach 0.40. To produce the final design, classic momentum and blade-element theories were combined with two and three-dimensional results from the Advanced Ducted Propfan Analysis Code (ADPAC), a numerical Navier-Stokes analysis code. The Eppler 387 airfoil was used for each of the constant section propeller designs compared. Experimental data from the Langley Low-Turbulence Pressure Tunnel was used in the strip theory design and analysis programs written. The experimental data was also used to validate ADPAC at a Reynolds numbers of 60,000 and a Mach number of 0.20. Experimental and calculated surface pressure coefficients are compared for a range of angles of attack. Since low Reynolds number transonic experimental data was unavailable, ADPAC was used to generate two-dimensional section performance predictions for Reynolds numbers of 60,000 and 100,000 and Mach numbers ranging from 0.45 to 0.75. Surface pressure coefficients are presented for selected angles of attack. in addition to the variation of lift and drag coefficients at each flow condition. A three-dimensional model of the final design was made which ADPAC used to calculated propeller performance. ADPAC performance predictions were compared with strip-theory calculations at design point. Propeller efficiency predicted by ADPAC was within 1.5% of that calculated by strip theory methods, although ADPAC predictions of thrust, power, and torque coefficients were approximately 5% lower than the strip theory results. Simplifying assumptions made in the strip theory account for the differences seen.

Koch, L. Danielle↗
NASA NTRS2015

Mach Stability Improvements Using an Existing Second Throat Capability at the National Transonic Facility

Recent data quality improvements at the National Transonic Facility (NTF) have an intended goal of reducing the Mach number variation in a data point to within unit vector A plus or minus 0.0005, with the ultimate goal of reducing the data repeatability of the drag coefficient for full-span subsonic transport models at transonic speeds to within half of a drag count. This paper will discuss the Mach stability improvements achieved through the use of an existing second throat capability at the NTF to create a minimum area at the end of the test section. These improvements were demonstrated using both the NASA Common Research Model and the NTF Pathfinder-I model in recent experiments. Sonic conditions at the throat were verified using sidewall static pressure data. The Mach variation levels from both experiments in the baseline tunnel configuration and the choked tunnel configuration will be presented. Finally, a brief discussion is given on the consequences of using the second throat in its location at the end of the test section.

Chan, David T.↗
NASA NTRSDate not supplied

Mixed-element USM3D Contributions to the 4th AIAA High-Lift Prediction Workshop

This paper discusses results of the mixed-element USM3D (USM3D-ME) simulations performed for the 4th AIAA High-Lift Prediction Workshop. The workshop was separated into six Technical Focus Groups to investigate the impact of geometry modeling, grid, and computational methods for predicting high lift flows. This work was performed under the Fixed Grid RANS Technical Focus Group. The primary geometry selected for the workshop was the High-Lift Common Research Model. The performed simulations included a flap deflection study and both a grid refinement study and pitch sweep for the nominal flap deflection configuration. The results show that USM3D-ME RANS solutions, generally, tends to underpredict the lift coefficient and to predict a less negative pitching moment relative to the experimental data. The predicted drag coefficient values agree better with experiment for smaller angles of attack but were observed to be larger than experiment for the largest angle of attack simulated. The results of the grid refinement study demonstrated a lack of grid convergence for the provided grid family. The results of the grid refinement study are consistent with the submissions to the Fixed Grid and Mesh Adaptation Technical Focus Groups. Grid convergence for the provided grid family remains elusive for the international community. A 2D Multielement Airfoil configuration was included to enable a turbulence model verification study, which illustrated favorable agreement between USM3D-ME and the solutions provided by other flow solvers.

CFD↗
NASA NTRSDate not supplied

Mixed-Element USM3D Contributions to the 4th AIAA High-Lift Prediction Workshop

This paper discusses results of the mixed-element USM3D (USM3D-ME) simulations performed for the 4th AIAA High-Lift Prediction Workshop. The workshop was separated into six Technical Focus Groups to investigate the impact of geometry modeling, grid, and computational methods for predicting high lift flows. This work was performed under the Fixed Grid RANS Technical Focus Group. The primary geometry selected for the workshop was the High-Lift Common Research Model. The performed simulations included a flap deflection study and both a grid refinement study and pitch sweep for the nominal flap deflection configuration. The results show that USM3D-ME RANS solutions, generally, tends to underpredict the lift coefficient and to predict a less negative pitching moment relative to the experimental data. The predicted drag coefficient values agree better with experiment for smaller angles of attack but were observed to be larger than experiment for the largest angle of attack simulated. The results of the grid refinement study demonstrated a lack of grid convergence for the provided grid family. The results of the grid refinement study are consistent with the submissions to the Fixed Grid and Mesh Adaptation Technical Focus Groups. Grid convergence for the provided grid family remains elusive for the international community. A 2D Multielement Airfoil configuration was included to enable a turbulence model verification study, which illustrated favorable agreement between USM3D-ME and the solutions provided by other flow solvers.

CFD↗
NASA NTRS1961

A Transonic Investigation of Changing Indentation Design Mach Number on the Aeodynamic Characteristics of a 45 deg Sweptback-Wing-Body Combination Designed for High Performance

The effects of changing indentation design Mach number on the aerodynamic characteristics of a 45 deg. sweptback-wing-body combination designed for high performance have been investigated at Mach numbers from 0.80 to 1.13 in the Langley 8-foot transonic tunnel and at a Mach number of 1.43 in the Langley 8-foot transonic pressure tunnel. The Reynolds number of the investigation covered the range from approximately 2.5 x 10 (exp 6) to approximately 3.0 x 10(exp 6) based on the mean aerodynamic chord of the wing. The 45 deg. sweptback wing with camber and a thickened root was tested at 0 deg. angle of incidence on an unindented body and on bodies indented for Mach numbers M of 1.0, 1.2, and 1.4. Transonic and supersonic area rules were used in the design of the indented bodies. Theoretical zero-lift wave drag was calculated for these wing-body combinations. A -2 deg. angle of incidence of the wing, and M = 1.4 revised body indentation, and fixed transition also were investigated. Experimental values of zero-lift wave drag for the indented-body combinations followed closely the area-rule concept in that the lowest zero-lift wave-drag coefficient was obtained at or near the Mach number for which the body of the combination was designed. Theoretical values of zero-lift wave drag were considered to be in good agreement with the experimental results. At a given supersonic Mach number the highest values of maximum lift-drag ratio for the various combinations also were obtained at or near the Mach number for which the body of the combination was designed. At Mach numbers of 1.0, 1.2, and 1.43, the maximum lift-drag ratios were 15.3, 13.0, and 9.2, respectively. The use of an angle of incidence of -2 deg. for the wing in combination with the M = 1.2 body increased the zero-lift wave drag and decreased the maximum lift-drag ratio. All configurations maintained stable characteristics up to the highest lift coefficient of the investigation (C(L) approx. equal to 0.5).

Loving, Donald L.↗
NASA NTRS1992

Further wind tunnel investigation of the SM701 airfoil with aileron and turbulators

Wind tunnel tests were performed on a two-dimensional model of the SM701 airfoil designed for use on the World Class gliders. The test covered a range of Reynolds numbers from 500,000 to 1.7 million. Aerodynamic forces and moments were measured with an external balance. Momentum loss method measurements of the section drag coefficient were also made. Flow visualization techniques provided information on transition from laminar to turbulent flow. Lift, drag, and pitching moment were analyzed and comparisons were made with predicted and previously obtained experimental data. The effects of V-tape turbulators for use in turbulent drag reduction were studied. The performance of a 25 percent chord aileron deflected through plus or minus 20 degrees was researched. The model was designed, constructed, and tested by students at Texas A&M University.

Steen, Gregory↗